87072

REVISIONS
LTR
DESCRIPTION
DATE
APPROVED
A
Add new source of supply; change temperature
coefficient of schematics 8, 11, and 13. Editorial
changes throughout.
20 May 1988
D. MOORE
B
Changes in accordance with NOR
5905-R012-93.
28 May 1993
D. MOORE
C
Update and validation of drawing.
Editorial changes throughout.
D
Add pure tin prohibition paragraph. Editorial
changes throughout.
29 Jan 2007
M. RADECKI
E
Dash numbers 08, 09, 10, 11, 12, and 13, the seat
height is .350 inch max. QR Code added. Vendor
address change. Editorial changes throughout
06 June 2016
M. RADECKI
11 Sep 2000
K. COTTONGIM
CURRENT DESIGN ACTIVITY CAGE CODE 037Z3
DEFENSE LOGISTICS AGENCY
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO 43218-3990
Prepared in accordance with ASME Y14.100
E
E
REV
REV STATUS
OF PAGES
1
2
PAGES
PMIC N/A
Original date of
drawing:
29 December 1987
E
E
E
3
4
5
6
PREPARED BY
Alan R. Knox
CHECKED BY
David W. Withrow
APPROVED BY
David E. Moore
SIZE
A
REV
AMSC N/A
E
CODE IDENT. NO.
14933
E
E
E
E
E
E
E
7
8
9
10 11 12
DESIGN ACTIVITY:
DEFENSE ELECTRONIC SUPPLY CENTER
DAYTON, OHIO 45444-5000
TITLE
RESISTOR NETWORK, FIXED, FILM, 10-PIN SIP,
MULTIPLE RESISTANCE VALUES, MULTIPLE
SCHEMATICS AND MULTIPLE TOLERANCES.
DWG NO.
87072
PAGE
1
OF
12
5905-2016-E29
1. SCOPE
1.1 Scope. This drawing describes the requirements for a 10-pin, single-in-line package (SIP), fixed, film, resistor
network.
1.2 Part or Identifying Number (PIN). The complete PIN is as follows:
87072

Drawing number
-
01

Schematic number
(see figure 2)
2. APPLICABLE DOCUMENTS
2.1 Government documents.
2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of
this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in
the solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATIONS
MIL-PRF-83401
-
Resistor Network, Fixed, Film, and Capacitor-Resistor Network, Ceramic
Capacitor and Fixed Film Resistor, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-1285
-
Marking of Electrical and Electronic Parts
(Copies of these documents are available online at http://quicksearch.dla.mil).
2.2 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of
this document and the references cited herein (except for related specification sheets), the text of this document takes
precedence unless otherwise noted. Nothing in this document, however, supersedes applicable laws and regulations
unless a specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item Requirements. The individual item requirements shall be in accordance with MIL-PRF-83401 and as specified
herein.
3.2 Interface and physical dimensions. The resistor shall meet the interface and physical dimensions as specified in
MIL-PRF-83401 and herein (see figure 1). For dash numbers 08, 09, 10, 11, 12, and 13, the seat height is .350 inch max
3.3 Electrical characteristics.
3.3.1 Resistance. The resistance value shall be as specified on figure 2.
3.3.2 Resistance tolerance. The resistance tolerance shall as specified on figure 2.
3.3.3 Resistor power rating. The resistor power rating for individual resistors shall be 125 milliwatts maximum at 70OC
derated to 0 watts at 150OC.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
87072
REV E
PAGE
2
*
* Dash numbers 08, 09, 10, 11, 12, and 13, the seat height is .350 inch max.
Inches
0.002
0.005
0.006
0.010
mm
0.05
0.12
0.15
0.25
Inches
0.019
0.098
0.100
0.125
mm
0.48
2.48
2.54
3.17
Inches
0.320
0.350
1.000
mm
8.12
8.89
25.40
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for general information only.
3. Unless otherwise specified, dimensional tolerances shall be ±0.02 (0.5 mm) for two decimal places and ±0.010
(0.25 mm) for three decimal places.
4. The picturization of the styles above is given as representative of the envelope of the item. Slight deviations from
the outline shown, which are contained within the envelope and do not alter the functional aspects of the device,
are acceptable.
FIGURE 1. Resistor network.
3.3.4 Package power rating. The package power rating shall not exceed the sum of the individual resistance element
power rating in the network.
3.3.5 Operating voltage. Each resistor element shall have a maximum operating voltage of 100 V dc or ac rms.
3.3.6 Schematic. Resistor networks are available in schematics listed on figure 2.
3.3.7 Resistance temperature characteristic. Unless otherwise specified, the resistance temperature characteristic
shall be ±100 ppm/OC.
3.4 Characteristic. The characteristic shall be in accordance with MIL-PRF-83401, characteristic K.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
87072
REV E
PAGE
3
NOTES:
1. Resistance tolerance shall be ±3 percent.
2. Resistor temperature coefficient shall be ±200 ppm/OC.
3. Power rating shall be 25 mW at +120OC.
4. kΩ = kilohms.
NOTES:
1. Resistance tolerance shall be ±3 percent.
2. Resistor temperature coefficient shall be ±200 ppm/OC maximum.
3. R1 and R5 power rating shall be 60 mW at +120OC. R2, R3, R4, R6, R7 and R8 power ratings shall be 25 mW
at +120OC.
4. Ω = ohms, kΩ = kilohms.
FIGURE 2. Schematic, resistance and tolerance.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
87072
REV E
PAGE
4
NOTES:
1. Resistance tolerance shall be ±3 percent.
2. Resistor temperature coefficient shall be ±200 ppm/OC maximum.
3. R1 and R6 power rating shall be 60 mW at +120OC. R2, R3, R4, R5, R7, R8 and R9 power ratings shall be
25 mW at +120OC.
4. Ω = ohms, kΩ = kilohms.
NOTES:
1. Resistance tolerance shall be ±3 percent.
2. Resistor temperature coefficient shall be ±200 ppm/OC maximum.
3. R3 and R6 power rating shall be 60 mW at +120OC. R1, R2, R4, R5, and R7 power ratings shall be 25 mW
at +120OC.
4. Ω = ohms, kΩ = kilohms
FIGURE 2. Schematic, resistance and tolerance - Continued.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
87072
REV E
PAGE
5
NOTES:
1. Resistance tolerance shall be ±3 percent.
2. Resistor temperature coefficient shall be ±200 ppm/OC.
3. Power rating shall be 25 mW at +120OC.
4. Ω = ohms, kΩ = kilohms.
NOTES:
1. Resistance tolerance shall be ±3 percent.
2. Resistor temperature coefficient shall be ±200 ppm/OC.
3. Power rating shall be 25 mW at +120OC.
4. Ω = ohms, kΩ = kilohms
FIGURE 2. Schematic, resistance and tolerance - Continued.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
87072
REV E
PAGE
6
NOTES:
1. Resistance tolerance shall be ±3 percent.
2. Resistor temperature coefficient shall be ±200 ppm/OC.
3. Power rating shall be 25 mW at +120OC.
4. Ω = ohms, kΩ = kilohms.
NOTES:
1. Resistance tolerance shall be ±1 percent.
2. Resistor temperature coefficient shall be ±100 ppm/OC maximum.
3. kΩ = kilohms.
FIGURE 2. Schematic, resistance and tolerance - Continued.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
87072
REV E
PAGE
7
NOTES:
1. Resistance tolerance shall be ±5 percent.
NOTES:
1. Resistance tolerance shall be ±1percent.
2. Resistor temperature coefficient shall be ±200 ppm/OC maximum; except R4 which shall be ±100 ppm/OC
maximum.
3. kΩ = kilohms.
FIGURE 2. Schematic, resistance and tolerance - Continued.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
87072
REV E
PAGE
8
NOTES:
1. Resistance tolerance shall be ±1 percent.
2. Resistor temperature coefficient shall be ±100 ppm/OC maximum.
3. kΩ = kilohms.
NOTES:
1. Resistance tolerance shall be ±5 percent.
2. kΩ = kilohms.
FIGURE 2. Schematic, resistance and tolerance - Continued.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
87072
REV E
PAGE
9
NOTES:
1. Resistance tolerance shall be ±1 percent.
2. Resistor temperature coefficient shall be ±100 ppm/OC maximum.
3. kΩ = kilohms.
NOTES:
1. Resistance tolerance shall be ±5 percent.
2. Resistor temperature coefficient shall be ±200 ppm/OC maximum.
3. Power rating shall be 20 mW per resistor.
4. kΩ = kilohms.
FIGURE 2. Schematic, resistance and tolerance - Continued.
3.5 Environmental requirements. The environmental requirements shall be in accordance with MIL-PRF-83401,
characteristic K.
3.6 Marking. Marking shall be in accordance with MIL-STD-1285 except the networks shall be marked with the PIN as
specified herein (see 1.2), the manufacturer's name or Commercial and Government Entity (CAGE) code, and date lot
codes.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
87072
REV E
PAGE
10
3.7 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on
the MIL-PRF-83401 Qualified Products List for at least one part, or perform the group A and group B inspections specified
herein on a sample of parts agreed upon by the manufacturer and DLA Land and Maritime - VAT.
3.7.1 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a
approved source of supply.
3.8 Pure tin. The use of pure tin, as an underplate or final finish, is prohibited both internally and externally. Tin
content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3
percent lead, by mass (see 6.3).
3.9 Recycled, recovered, environmentally preferable, or biobased materials. Recycled, recovered, environmentally
preferable, or biobased materials should be used to the maximum extent possible, provided that the material meets or
exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs.
3.10 Workmanship. Resistors shall be uniform in quality and free from defects that will affect life, serviceability, or
appearance.
4. VERIFICATION
4.1 Qualification inspection. Qualification inspection is not applicable to this document.
4.2 Conformance inspections.
4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A and group B
inspections of MIL-PRF-83401.
4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B
requirements in lieu of performing group B tests (see 6.2d).
4.3 Inspection of packaging. Inspection of packaging shall be in accordance with MIL-PRF-83401.
4.4 Visual and mechanical examination. Resistors shall be examined to verify that the materials, design, construction,
physical dimensions, marking, and workmanship are in accordance with the applicable requirements of MIL-PRF-83401.
5. PACKAGING
5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order
(see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need
to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are
maintained by the Inventory Control Point's packaging activities within the Military Service or Defense Agency, or within
the military service's system commands. Packaging data retrieval is available from the managing Military Department's or
Defense Agency's automated packaging files, CD-ROM products, or by contacting the responsible packaging activity.
6. NOTES
(This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.)
6.1 Intended use. Resistor networks are used in surface mounting applications where space is a major concern.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
87072
REV E
PAGE
11
6.2 Ordering data. The contract or purchase order should specify the following:
a. Complete PIN (see 1.2).
b. Requirements for delivery: One copy of the conformance inspection data or certification of compliance that parts
have passed conformance inspection with each shipment of parts by the manufacturer.
c.
Requirements for packaging and packing. (i.e. ESD sensitive packaging).
d. Whether the manufacturer performs the group B tests or provides certification of compliance with group B
requirements.
6.3 Electrostatic charge. Under several combinations of conditions, these resistors can be electrically damaged, by
electrostatic charges, and drift from specified value. Users should consider this phenomena when ordering or shipping
resistors. Direct shipment to the Government is controlled by MIL-DTL-39032 which specifies a preventive packaging
procedure.
6.4 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker
growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can
develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a
whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to
inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification
for Electrodeposited Coatings of Tin).
6.5 User of record. Coordination of this document for future revisions is coordinated only with the approved source of
supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be
achieved online at [email protected] or in writing to: DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH
43218-3990 or by telephone (614) 692-8754 or DSN 850-8754.
6.6 Approved source of supply. Approved source of supply is listed herein. Additional sources will be added as they
become available. Assistance in the use of this drawing may be obtained online at [email protected] or contact
DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-8754 or
DSN 850-8754.
DLA Land and Maritime
drawing PIN
Vendors similar
designation or
type number 1/
Vendor
CAGE
Vishay Techno
P.O. Box 609,
1122 23rd St.,
Columbus, NE 68602-0609
10SM-****-FX
87072-**
Vendor's name
and address
91637
MSP 10 or
CSC10
http://www.vishay.com/
Vishay Dale
P.O. Box 609,
1122 23rd St.,
Columbus, NE 68602-0609
http://www.vishay.com/
1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all
performance requirements and test are met.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
87072
REV E
PAGE
12