P13L www.vishay.com Vishay Sfernice Long Life Cermet Potentiometer up to 2 Million Cycles FEATURES • 2 million cycles for bushing L and N • 1 million cycles for bushing T, Q, O, and P • High power rating 1.5 W at 70 °C • Test according to CECC 41000 or IEC 60393-1 • Cermet element Their excellent performances are due to the use of a cermet-track sealed in a large case. • Fully sealed case P13 interchangeability with RV6, combined with the excellent stability of its rated characteristics make it fully acceptable for industrial and professional uses. • Custom designs on request • Mechanical strength • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 DIMENSIONS in millimeters (± 0.5) P13LT 10 wrench 0.7 10.5 max. Panel Cutout Ø 2.2 Thread M6 x 0.75 8 1.6 Slot 0.6 x 1 deep Ø 12.6 b 0.3 Ø3 AA = 9.5 5 5.9 ± 0.2 2 5.08 c 5.08 a 1.6 AB = 12.5 Ø 6.5 0.8 AJ = 22 2.4 P13LQ 10 wrench 0.7 10.5 max. Panel Cutout Thread M7 x 0.75 8 Ø 12.6 b 0.3 Ø4 2 5.08 c 5.08 EA = 9.5 5 Ø 2.2 1.6 Slot 0.8 x 1.4 deep 5.9 ± 0.2 a 1.6 EB = 12.5 Ø 7.5 0.8 EJ = 22 2.4 P13LL Panel Cutout Thread M10 x 0.75 10.5 max. 12 1.6 Slot 1 x 1.8 deep Ø6 Ø 14 5 0.3 2 5.08 c 5.08 FG = 16 a 1.6 FL = 25 FR = 50 Revision: 23-Sep-15 b Ø 10.5 0.8 2.4 Document Number: 51065 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 P13L www.vishay.com Vishay Sfernice ELECTRICAL SPECIFICATIONS Resistive element Cermet Electrical travel 270° ± 10° Standard resistance value 1 k, 5 k, 10 k, 50 k Tolerance ± 20 % % TOTAL RESISTANCE 100 Taper 80 F 60 A L 40 20 0 0 20 40 60 80 100 % CLOCKWISE SHAFT ROTATION c a Circuit diagram (3) (1) cw b (2) 1.5 Power rating POWER IN W LIN. TAPER A Linear 1.5 W at 70 °C Logarithmic 0.75 W at 70 °C 1 LOG. TAPER L and F 0.5 0 0 20 40 60 70 80 100 120 140 AMBIENT TEMPERATURE IN °C Resistance Value (k) Standard resistance element data 1 5 10 50 Temperature coefficient (typical) Limiting element voltage (linear law) End resistance (typical) Linear Taper Non-Linear Taper Max. Power Max. Working Max. Power Max. Working at 70 °C Voltage at 70 °C Voltage (W) (V) (W) (V) 1.5 1.5 1.5 1.5 38.7 86.6 122 274 27.4 61.2 87 194 ± 150 ppm/°C 350 V 1 Dielectric strength (RMS) 2000 V Insulation resistance (300 VDC) 106 M Independent linearity (typical) ±5% Revision: 23-Sep-15 0.75 0.75 0.75 0.75 Document Number: 51065 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 P13L www.vishay.com Vishay Sfernice MECHANICAL SPECIFICATIONS Mechanical travel 300° ± 5° Operating torque (typical) 2 Ncm max. 2.85 oz. inch max. Style T, Q 35 Ncm max. 3.1 lb inch max. Style L 80 Ncm max. 7.1 lb inch max. Style T, Q 150 Ncm max. 13.3 lb inch max. Style L 250 Ncm max. 22.1 lb inch max. End stop torque Tightening torque of mounting nut Unit weight 6 g to 18 g max. 0.22 oz. to 0.64 oz. Terminals e3: Pure Sn ENVIRONMENTAL SPECIFICATIONS Temperature range -55 °C to +125 °C Climatic category 55/125/56 Sealing Fully sealed - Container IP67 OPTIONS Special feature command shaft Length is measured from the mounting surface to the free end of the shaft. The screwdriver slot is aligned with the wiper within ± 10°. Special shafts are available, in accordance to drawings supplied by customers. We recommend that customers should not machine tool shafts, in order to avoid damage. Bending or torsion of terminals should also be avoided. Potentiometers P13LT and P13LL can be fitted with a device providing sealing between the threaded bushing and the front panel. Their designation is P13LP and P13LN respectively or with a locating peg P13LP...E and P13LN...E. Panel sealed version P13LP P13LP...E: Including locating peg Panel Cutout 0.7 13.2 max. 8 Thread M6 x 0.75 1.6 Slot 0.6 x 1 deep Ø 12.6 Ø3 Ø 1.5 0.3 3.9 ± 0.2 5.08 AA = 9.5 5 2 5.08 Ø 6.5 1.6 AB = 12.5 0.8 AJ = 22 2.4 Panel sealing Panel sealed version P13LN P13LN...E: Including locating peg Thread M10 x 0.75 13.5 max. 9.5 Ø 1.5 0.3 Ø6 Ø 16 Ø 14 5 Panel Cutout 1.6 Slot 1 x 1.8 deep 2 5.08 6.9 ± 0.2 5.08 FE = 13.5 FK = 22.5 1.6 Ø 10.5 0.8 FQ = 47.5 2.4 Revision: 23-Sep-15 Document Number: 51065 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 P13L www.vishay.com Vishay Sfernice OPTIONS On potentiometers equipped with a 3 mm Ø shaft, shaft locking can be obtained: • Either by a taper nut tightening a slotted bushing. Ask for P13LO type. These devices are normally equipped with an AB type shaft (12.5 mm with a slot). P13LO 10 wrench Slotted bushing Thread M6 x 0.75 8 wrench 0.7 Ø3 11 AB = 12.5 Shaft locking • Or by a tightening nut locked by a screw. Ask for ES1 type. On potentiometers equipped with a Ø 6 mm shaft, locking can be obtained by a taper nut applying pressure on a slotted notched washer. This device is supplied in a box as an accessory. Ask for DBAN. These devices are ordered separately. Please consult Vishay Sfernice. P13LL DBAN 12 wrench 6.5 No locking on shaft Ø 4 mm. MARKING Printed: • Vishay trademark • Part number (including ohmic value code, tolerance code and taper) • Manufacturing date code • Marking of terminals a APPLICATION NOTE c (3) The potentiometer shall be used in voltage divider with an impedance load at least 100 times higher than the total potentiometer nominal resistance value. Advised load impedance: 1 M min. for resistance range of 1 k to 50 k cw Vin Z> 1 MΩ (2) b Vout (1) a PACKAGING • • • • In box of 8 pieces for shafts FR and FQ In box of 10 pieces for shafts FE, FL, FG, and FK In box of 15 pieces for shafts AJ and EJ In box of 25 pieces for shafts AB, AA, EA, and EB PERFORMANCE TYPICAL VALUES AND DRIFTS TESTS Electrical endurance Revision: 23-Sep-15 CONDITIONS 1000 h at rated power 90’/30’ - ambient temp. 70 °C RT/RT (%) R1-2/R1-2 (%) OTHER ± 20 % ± 20 % - Document Number: 51065 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 P13L www.vishay.com Vishay Sfernice PERFORMANCE TYPICAL VALUES AND DRIFTS TESTS RT/RT (%) R1-2/R1-2 (%) OTHER ± 0.5 % ±1% - ± 0.5 % ±1% Dielectric strength: 1000 V Insulation resistance: > 104 M ± 0.5 % - - ± 20 % - Independent linearity: ± 10 % ± 0.1 % ± 0.2 % - ± 0.1 % - V1-2/V1-3 < ± 0.2 % CONDITIONS Phase A dry heat 125 °C Phase B damp heat Phase C cold -55 °C Phase D damp heat 5 cycles 56 days 40 °C 93 % HR 5 cycles -55 °C at +125 °C Bushings L and N: 2 000 000 cycles Bushings T, Q, O, and P: 1 000 000 cycles at rated power Turn angle ± 60° Temperature ± 20 °C 50 g‘s at 11 ms 3 successive shocks in 3 directions 10 Hz to 55 Hz 0.75 mm or 10 g‘s during 6 h Climatic sequence Damp heat, steady state Change of temperature Mechanical endurance Shock Vibration Note • Nothing stated herein shall be construed as a guarantee of quality or durability. ORDERING INFORMATION (part number) P MODEL 1 3 L Q BUSHING P13L E SHAFT Ø L 6 8 Q 7 8 AA L 10 12 AB O 6 11 AJ 3 22 T, P P 6 8 EA 4 9.5 Q EB 4 12.5 Q EJ 4 22 Q T L Only with bushing 3 9.5 T, P 3 12.5 T, P, O Ø N 10 9.5 FG 6 16 L FL 6 25 L FR 6 50 L FE 6 13 N FK 6 22 N FQ 6 47.5 N A S 1 0 3 SHAFT END OHMIC VALUE S = slotted F = flatted R = round D = custom 102 = 1 k 502 = 5 k 103 = 10 k 503 = 50 k M L E TOLERANCE TAPER SPECIAL M = 20 % A = linear L = clockwise logarithmic F = inverse clockwise logarithmic E= locating peg or special code given by Vishay PART NUMBER DESCRIPTION (for information only) P13L Q E EA 10K 20 % L MODEL BUSHING SPECIAL SHAFT VALUE TOLERANCE TAPER BO25 SPECIAL PACKAGING e3 SHAFT SPECIAL LEAD (Pb)-FREE RELATED DOCUMENTS APPLICATION NOTES Potentiometers and Trimmers www.vishay.com/doc?51001 Guidelines for Vishay Sfernice Resistive and Inductive Components www.vishay.com/doc?52029 Revision: 23-Sep-15 Document Number: 51065 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000