P6LU_ENLF

P6LU-xxxxE/ZH60ENLF
PML-SERIES
Rev.06-2009
1 Watt
Unregulated
Single and Dual Output
SIP7 Case
6 kV DC I/O Isolation
Low Coupling Capacity
Rated Voltage for 250 Vrms
Mainzer Straße 151–153
D-55299 Nackenheim
Tel. +49 6135 7026-0
Fax: +49 6135 931070
www.peak-electronics.de
[email protected]
The PML series P6LU-xxxxE/ZH60ENLF is a family of cost effective 1 W
single & dual output DC-DC converters. These converters are in an ultra
miniature SIP7 case without compromising performance. The bigger case
ensures the physical clearance of isolation barrier of 2.5mm which
increases the reliability under high pot from 6kV DC. Devices are
encapsulated. High performance features: 6kV input/output isolation, high
efficiency, output voltage accuracy of ±3%, input range of ±10%, low
output ripple and noise and long term short circuit protection.
All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified
Input Specifications
Voltage Range
Input Filter
Input Reflected Ripple Current¹
± 10%
Capacitor
20 mA pk-pk
Output Specifications
Voltage Accuracy
Short Circuit Protection
Line Regulation
Load Regulation (10% - 100%)
Ripple and Noise (20Mhz bandwidth)
Temperature Coefficient
± 3%
Indefinite (automatic recovery)
± 1.2% / 1% Vin Change
± 10%
200 mV pk-pk
± 0.03% / °C
General Specifications
Efficiency
I/O Isolation Voltage (3 sec. flash test)
I/O Isolation Capacity
I/O Isolation Resistance
Switching Frequency
Humidity
Reliability Calculated MTBF (MIL-HDBK-217F)
Safety Standard (designed to meet)
See table
6000 VDC
10 pF, typ.
1000 M Ohm
20 - 50 kHz, typ.
95% rel H
>2.39 Mhrs
IEC 60950-1:2001
Physical Specifications
Clearance Distance (Input to Output)
Case Material
Potting Material
Weight
2.5 mm
Epoxy encapsulated (UL94V-0 rated)
Epoxy (UL94V-0 rated)
~ 4.2g, typ.
Environment Specifications
Operating Temperature
Maximum Case Temperature
Storage Temperature
Cooling
RoHS Conform
-40 to +85 °C (ambient)
100°C
-40 to +125°C
Free Air Convection (10 mm distance required)
Soldering 260°C, max. (1.5 mm from case 10s.)
PML-Series – P6LU-xxxxE/ZH60ENLF – Single and Dual Output – SIP7 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 1/4
Selection Guide
Single Output
m A)
ad (
)
o
L
C
l
ul
uF)²
VD
(V
)
ad (
ge ( rrent F
e
o
a
%
g
t
L
(
l
a
y
lt
or
Vo
Cu
t Vo
ienc
a c it
put
pu t
Inpu
O ut
O ut
Effic
Cap
DC)
Order #
SINGLE OUTPUT
P6LU-053R3EH60ENLF
P6LU-0505EH60ENLF
P6LU-0509EH60ENLF
P6LU-0512EH60ENLF
P6LU-0515EH60ENLF
P6LU-093R3EH60ENLF
P6LU-0905EH60ENLF
P6LU-0909EH60ENLF
P6LU-0912EH60ENLF
P6LU-0915EH60ENLF
P6LU-123R3EH60ENLF
P6LU-1205EH60ENLF
P6LU-1209EH60ENLF
P6LU-1212EH60ENLF
P6LU-1215EH60ENLF
P6LU-153R3EH60ENLF
P6LU-1505EH60ENLF
P6LU-1509EH60ENLF
P6LU-1512EH60ENLF
P6LU-1515EH60ENLF
P6LU-243R3EH60ENLF
P6LU-2405EH60ENLF
P6LU-2409EH60ENLF
P6LU-2412EH60ENLF
P6LU-2415EH60ENLF
5
5
5
5
5
9
9
9
9
9
12
12
12
12
12
15
15
15
15
15
24
24
24
24
24
3.3
5
9
12
15
3.3
5
9
12
15
3.3
5
9
12
15
3.3
5
9
12
15
3.3
5
9
12
15
303
200
111.1
83.3
66.7
303
200
111.1
83.3
66.7
303
200
111.1
83.3
66.7
303
200
111.1
83.3
66.7
303
200
111.1
83.3
66.7
69 - 75
70 - 77
70 - 80
70 - 80
70 - 80
69 - 75
70 - 77
70 - 80
70 - 80
70 - 80
69 - 75
70 - 77
70 - 80
70 - 80
70 - 80
69 - 75
70 - 77
70 - 80
70 - 80
70 - 80
69 - 75
70 - 77
70 - 80
70 - 80
70 - 80
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
If you need other specifications, please enquire.
PML-Series – P6LU-xxxxE/ZH60ENLF – Single and Dual Output – SIP7 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 2/4
Selection Guide
Dual Output
m A)
ad (
)
o
L
C
l
ul
uF)²
VD
(V
nt F
)
ad (
ge (
e
e
o
a
r
%
g
t
r
(
L
l
a
y
lt
or
Cu
Vo
ie n c
t Vo
acit
pu t
put
Inpu
O ut
O ut
Effic
Cap
DC)
Order #
DUAL OUTPUT
P6LU-053R3ZH60ENLF
P6LU-0505ZH60ENLF
P6LU-0509ZH60ENLF
P6LU-0512ZH60ENLF
P6LU-0515ZH60ENLF
P6LU-093R3ZH60ENLF
P6LU-0905ZH60ENLF
P6LU-0909ZH60ENLF
P6LU-0912ZH60ENLF
P6LU-0915ZH60ENLF
P6LU-123R3ZH60ENLF
P6LU-1205ZH60ENLF
P6LU-1209ZH60ENLF
P6LU-1212ZH60ENLF
P6LU-1215ZH60ENLF
P6LU-153R3ZH60ENLF
P6LU-1505ZH60ENLF
P6LU-1509ZH60ENLF
P6LU-1512ZH60ENLF
P6LU-1515ZH60ENLF
P6LU-243R3ZH60ENLF
P6LU-2405ZH60ENLF
P6LU-2409ZH60ENLF
P6LU-2412ZH60ENLF
P6LU-2415ZH60ENLF
5
5
5
5
5
9
9
9
9
9
12
12
12
12
12
15
15
15
15
15
24
24
24
24
24
± 3.3
±5
±9
± 12
± 15
± 3.3
±5
±9
± 12
± 15
± 3.3
±5
±9
± 12
± 15
± 3.3
±5
±9
± 12
± 15
± 3.3
±5
±9
± 12
± 15
± 151.5
± 100
± 55.6
± 41.7
± 33.3
± 151.5
± 100
± 55.6
± 41.7
± 33.3
± 151.5
± 100
± 55.6
± 41.7
± 33.3
± 151.5
± 100
± 55.6
± 41.7
± 33.3
± 151.5
± 100
± 55.6
± 41.7
± 33.3
68 - 75
70 - 78
70 - 81
72 - 81
70 - 81
68 - 75
70 - 78
70 - 81
72 - 81
70 - 81
68 - 75
70 - 78
70 - 81
72 - 81
70 - 81
68 - 75
70 - 78
70 - 81
72 - 81
70 - 81
68 - 75
70 - 78
70 - 81
72 - 81
70 - 81
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
± 100
If you need other specifications, please enquire.
PML-Series – P6LU-xxxxE/ZH60ENLF – Single and Dual Output – SIP7 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 3/4
Package / Pinning / Derating
2.13
(0.08)
All dimensions are typical in millimeters (inches).
- Pin diameter: 0.5 +/-0.05 (0.02 +/-0.002)
- Pin pitch tolerance: +/-0.35 (+/-0.014)
- Case tolerance +/-0.5 (+/-0.02)
Specification may change without notice.
0.50
(0.02)
0.50
(0.02)
9.80
(0.39)
19.50
(0.76)
PEAK
Modelcode
Datecode
1
2.54
(0.10)
2
5
15.24
(0.60)
6
7
SIP7 – „ENLF“ PLASTIC CASE
#
1
2
5
6
7
PIN CONNECTIONS
SINGLE
DUAL
+Vin
+Vin
- Vin
- Vin
- Vout
- Vout
Omitted
Common
+Vout
+Vout
App Notes:
¹ = Measured Input reflected ripple current with a simulated source inductance of 12uH.
² = Tested by minimal Vin and constant resistive load.
- Operation under no-load conditions will not damage these devices, but they will not observe the listed specifications.
- For reduce converter’s ripple & noise, it is recommended to add a 4.7µF~100µF(±4.7µF~±68µF for dual output) capacitor at
the output. For EMI performance improvement, it is recommended to add a 12µH inductor and a 10µF~100µF capacitor at the
input.
PML-Series – P6LU-xxxxE/ZH60ENLF – Single and Dual Output – SIP7 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 4/4