Pan-Steel® Stainless Steel Systems Improved Productivity and Worker Safety for Bundling, Fastening, and Identification in Harsh Environments When strength, vibration, radiation, weathering, corrosion and temperature extremes are a factor, the Pan-Steel® System provides strong, reliable solutions for use in indoor, outdoor, and direct burial applications. This guide provides an overview of key design considerations and applications for bundling, fastening, and permanent identification in harsh environments. APPLICATION GUIDE Industrial Oil Rigs Refineries Chemical Plants Water Treatment Facilities Wind Farms Solar Nuclear Introduction Using this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pan-Steel® System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–7 Mining Ships Submarines Key Selection Criteria Performance in Harsh Environments . . . . . . . . . . . . . . . . . . . 8–9 Effective Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Strength for Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Aerial Support Lowest Installed Cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Telecommunications Workplace Safety and Abrasion Protection . . . . . . . . . . . . . . 11 Product Selection Guides Cable Ties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 – 13 Installation Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Permanent Identification System . . . . . . . . . . . . . . . . . . . . . . 14 Cell Towers Transportation OEM Compliance with Industry Standards Pan-Steel® System Approvals . . . . . . . . . . . . . . . . . . . . . . . . 15 Panduit Difference Complete Solution from Panduit . . . . . . . . . . . . . . . . . . . . . . 16 www.panduit.com Introduction Using this Guide Applications This section includes product recommendations for typical applications, always verify product suitability based on your specific requirements and key selection criteria Key Selection Criteria Utilize material and strength charts to help select the Panduit products required to deliver superior performance in your application Select the appropriate tools to speed installation time, and take advantage of our lowest installed cost solutions Consider Panduit permanent identification solutions to help provide legibility in harsh environments; the complete system includes marker plates, tags and ties and is available for use with On-site Custom Marking Tools or through our Factory Custom Marking Service Selection Guides Organized by part number, use each chart to assist with your product selection Pan-Steel® System Reliable system performance: Delivers strength, long life and resistance to chemicals, vibration, radiation, weathering, and extreme temperatures Increased job site safety: Features rounded edges to prevent installer injury and damage to cable bundles or finished product Lowest installed cost: Includes reliable, ergonomic tooling and an innovative cable tie design to provide fast and reliable installation Effectively identified workplace: Offers the most comprehensive selection of on-site and factory custom marking products in the industry Standards compliance: 2 www.panduit.com Meets and exceeds the most stringent industry standards Stainless Steel Cable Ties This section includes product recommendations for typical applications, always verify product suitability based on your specific requirements and key selection criteria Retained Tension Ties Panduit retained tension ties deliver a durable, secure fastening solution for mechanical applications. The system delivers the highest retained tension in the industry, providing tight fastening of rigid materials in high vibration and harsh environments. Stainless Steel Strapping Panduit coated and uncoated stainless steel strapping is the ultimate solution for large mechanical applications. The buckle design and installation tools offer a quick and safe installation. Aluminum Cable Ties Panduit aluminum cable ties are used to bundle and identify cabling or secure aluminum marker plates and tags to cabling and devices. Aluminum cable ties are a lightweight, flexible bundling, and permanent identification solution. Permanent Identification The widest range of permanent identification solutions available includes stainless steel and aluminum cable ties, marker plates and tags in a variety of shapes and sizes. Factory custom marking service delivers embossed or laser etched identification. On-site marking tools are excellent for quick and easy identification in the field. Installation Tools Panduit cable ties and industry leading installation tools work together to provide repeatable high performance at the lowest installed cost. Ergonomic tools are available for low, medium, and high volume applications. Reliability is designed into every tool. Strong, safe, and reliable solutions for long service life and lowest installed cost in harsh environments Total Installed Cost Comparison $ $ $ $ $ $ Panduit Self-Locking Cable Ties $ $ $ $ Safety Occurrence Labor Cost Material Cost $ $ Competitor B Strapping Panduit stainless steel cable ties and permanent identification solutions can deliver a useable life greater than 30 years. The combined value of material cost, labor savings, and improved safety results in the lowest total installed cost. www.panduit.com 3 Applications Panduit offers a wide variety of metal cable bundling, mechanical fastening, and permanent identification solutions to meet your specific application requirements. Common applications include: Cable Tray, Outdoor – Oil Rigs, Refineries Description: Electrical or Communication Cabling secured to cable tray in harsh environment. Selection Criteria: Resistance to extreme temperatures, chemicals, salt-water spray, ultra-violet light. Product Recommendations: • For Horizontal, Stainless Steel Cable Tray – Use Uncoated Heavy 316 Stainless Steel Metal Locking Tie • For Vertical, Stainless Steel Cable Tray – Use Uncoated Extra-Heavy 316 Stainless Steel Metal Locking Tie • For Horizontal, Aluminum Cable Tray – Use Coated Heavy 316 Stainless Steel Metal Locking Tie • For Short Circuit – up to 112kA – Use Metal Locking Ties or MS75 Metal Strapping Cable Tray, Indoor – Ships, Submarines, Chemical Plants, Industrial Facilities Description: Electrical or Communication Cabling secured to cable tray in harsh environment. Selection Criteria: Resistance to extreme temperatures, chemicals, vibration, and shock. Product Recommendations: • For Horizontal, Stainless Steel Cable Tray – Use Uncoated Heavy 316 Stainless Steel Metal Locking Tie • For Vertical, Stainless Steel Cable Tray – Use Uncoated Extra-Heavy 316 Stainless Steel Metal Locking Tie • For Horizontal, Aluminum Cable Tray – Use Coated Heavy 316 Stainless Steel Metal Locking Tie • For Short circuit – up to 71.5kA – Use Super-Heavy Double Loop 316 Stainless Steel Metal Locking Tie • Cushion Sleeving available for military applications • For Short Circuit – up to 112kA – Use Metal Locking Ties or MS75 Metal Strapping Instrument Tubing – Oil Rigs, Refineries, Chemical Plants, Industrial Facilities Description: Instrument tubing secured to pipe or rail in harsh environment. Selection Criteria: Retained tension, resistance to extreme temperatures, chemicals, salt-water spray, ultra-violet light. Product Recommendations: • Coated 1/2" Wide (12.7mm) 316 Stainless Steel Custom Length Strapping 4 www.panduit.com Pipe Insulation – Chemical Plants, Refineries, Industrial Facilities Description: Secure metal shield over pipe insulation. Selection Criteria: Resistance to extreme temperatures, chemicals, ultra-violet light. Product Recommendations: • Uncoated Extra-Heavy 15, 304 Stainless Steel Metal Locking Tie Rubber Steering Rack Boot – Trucks, Autos Description: Securing CV boots or steering rack boots on vehicles. Selection Criteria: Resistance to high temperatures, salt spray and chemicals, retained tension, liquid tight seal. Product Recommendations: • Standard or Light-Heavy 360° Radial Seal 304 Stainless Steel Retained Tension Tie Heat Shields – Motorcycles, Trucks, Autos, Aircraft Description: Secure heat shields on engines. Selection Criteria: Retained tension, resistance to extreme temperatures, thermal expansion, salt spray, chemicals. Product Recommendations: • Standard, Light-Heavy, or Heavy 304 Stainless Steel Retained Tension Tie www.panduit.com 5 Aerial Support – Railway, Power, and Communication Lines Description: Electrical or Communication Cabling secured to support structure. Selection Criteria: Resistance to extreme temperatures, chemicals, ultra-violet light. Product Recommendations: • Uncoated Heavy or Extra-Heavy 304 Stainless Steel Metal Locking Tie • Stackable spacers available Cable Identification – Cell Towers, Oil Rigs, Ships, Submarines, Industrial Facilities, Mining Description: Electrical or Communication Cabling secured to support structure and identification. Selection Criteria: Resistance to extreme temperatures, ultra-violet light. Product Recommendations: • 304 Stainless Steel Marker Plate (Embossed) • Aluminum Marker Plate (Embossed) • Uncoated Heavy 304 Stainless Steel Metal Locking Tie • Aluminum Metal Locking Tie Pipe Identification – Water Treatment Facilities, Refineries, Chemical Plants, Industrial Facilities 6 www.panduit.com Description: Securing stainless steel or aluminum tags onto valve, conduit, pipe, cable. Selection Criteria: Resistance to chemicals, extreme temperatures, ultra-violet light. Product Recommendations: • 304 Stainless Steel Marker Plate • Standard, Light-Heavy, or Heavy 304 Stainless Steel Metal Locking Tie Valve Identification – Industrial Facilities Description: Securing stainless steel or brass tags to valve. Selection Criteria: Resistance to extreme temperatures, ultra-violet light. Product Recommendations: • Brass Marker Tag • Standard 304 Stainless Steel Metal Locking Tie General Mechanical – Sign and Signal Mounting Description: Securing signs to outdoor poles. Selection Criteria: High strength and secure installation. Product Recommendations: • MS75 Strapping System Telecommunications Backbone – Commercial Building Description: Bundling Fiber Optic Cabling to aluminum cable tray. Selection Criteria: Strength, cable protection and corrosion resistance. Product Recommendations: • Coated Heavy 316 Stainless Steel Metal Locking Tie (apply at lowest tension setting) www.panduit.com 7 Key Selection Criteria Variables such as exposure to extreme temperatures, salt spray, and weather have differing effects on the performance of stainless steel and aluminum. Each of these factors contributes to the useful life of a cable tie, marker plate, or tag. Use the following sections as a guide to select the optimum Pan-Steel® Solution for your application. • Performance in harsh environments • Strength for application • Workplace safety and abrasion protection • Lowest installed cost • Effective identification • Compliance with industry standards Panduit stainless steel cable ties perform exceptionally well in temperature, chemical, and environmental extremes. Performance in Harsh Environments Materials Stainless steel: Recommended for harsh environment and general purpose applications where strength and/or resistance to severe conditions are required. Aluminum: Recommended in applications where light weight and flexibility are required. It is also well suited for use with aluminum cable tray to avoid corrosion from dissimilar metals. Loop Tensile Strength UV Resistance Extreme Temps Salt Spray Chemicals 201 Stainless Steel Best Best Best Good Good Not Recommended None 304 Stainless Steel Best Best Best Good Better Not Recommended None 316 Stainless Steel Best Best Best Best Best Not Recommended None Coated 316 Stainless Steel Better Good Better Good Good Best UL94V-2 Aluminum Good Best Good Good Good Best None Material Contact with Aluminum Flammability Material Selection for Temperature Resistance The following are recommended operating temperature ranges for stainless steel and aluminum. The operating temperature for uncoated and coated stainless steel is -112°F (-80°C) to 1,000°F (538°C) (Uncoated), -76°F (-60°C) – 572°F (300°C) (Nylon) and -40°F (-40°C) to 302°F (150°C) (Polyester). The operating temperature for Aluminum is -112°F (-80°C) to 212°F (100°C). Temperature Rating 1200 Temperate Rating 1000 800 600 400 200 0 -112 8 www.panduit.com 201 Stainless Steel 304 Stainless Steel 316 Stainless Steel Nylon 11 Coated Stainless Steel Polyester Coated Stainless Steel Aluminum Material Selection for Salt Spray Resistance Panduit cable ties were subjected to salt spray testing for 2,000 hours at 95°F (35°C). Both materials showed no signs of corrosion. The 316 Stainless Steel had trace surface staining and is recommended for mission critical applications. The 304 Stainless Steel had moderate surface staining and is recommended for general applications. 2,000 Hours 95°F (35°C) Material Selection for Weather Exposure Panduit cable ties were exposed to weather for prolonged lengths of time outside our manufacturing facility in Illinois, USA, without loss of performance or signs of corrosion. Loop tensile strength increased from year one to year four and remained stable over time. Weather Conditioning Loop Tensile Strength (Lbs.) 700 600 500 316 Stainless Steel Coated 400 304 Stainless Steel 316 Stainless Steel 300 200 100 0 Year 0 Year 4 Year 7 Year 11 Years of Exposure Effective Identification Panduit offers the broadest range of permanent identification solutions in the industry to withstand and provide legibility in harsh environments. Safe, quick, and easy to install, permanent identification solutions include stainless steel and aluminum marker plates, tags, marking tools, and ties to deliver improved productivity and workplace safety. On-site Custom Marking Tools provide portability for permanent identification and demand. Panduit also offers a Factory Custom Marking Service for embossed or laser etched marker plates, tags, and ties to speed installation time and reduce labor costs. This global custom marking service provides rapid response and quick product availability to keep projects on schedule and within budget. www.panduit.com 9 Strength for Application Split Mandrel Cable tie design, material selection, and installation tooling determine the resulting strength of a system. Use the following table as a guide to determine the strength of various Panduit stainless steel cable ties and strapping for your applications. The split mandrel test fixture is used to measure loop tensile strength and retained tension of an installed cable tie. Loop Tensile Strength Performance Loop Tensile Strength Loop Tensile Strength: 1,800 Rated load based on statistical analysis with additional margin. Tested mean based on sum of loop tensile strength over sample size. Loop Tensile Strength (Lbs.) 1,600 1,400 1,200 1,000 800 600 400 200 MLT Ties and Strapping Rated Load 0 Standard Retained Tension Light Heavy Heavy ExtraHeavy Cross Section ExtraHeavy 15 Retained Tension: Retained Tension Performance Comparison Retained Tension (Lbs.) Tested Mean SuperHeavy Measured in pounds of residual force remaining on object after tie is installed. 120 100 80 60 Panduit Retained Tension Tie (Heavy) 40 Metal Licking Tie 20 Band Clamp 0 MRT and MRS Ties Pinch Ear Clamp *Representative sample, actual results may vary. Rotational Torque Rotational Torque Rotational torque: 9 Torque (ft.- Lbs.) 8 Measured in pounds of force required to cause deflection of the tie or strapping when applied to a non-resistant object. 7 6 5 4 3 2 1 MRT and MRS Ties 0 Panduit MRT Tie Competitor Punch Style Cable Tie Competitor Pinch Ear Clamp Vibration and Shock: Electrical cables were secured to cable tray using Panduit stainless steel cable ties. The cable assemblies were subjected to multiple levels of severe vibration and shock loading. No damage occurred to the cable ties or cable insulation jacket, which prevented short circuits from occurring. 5 4 60 3 40 2 20 1 0 0 1 2 Test 10 www.panduit.com Hz G-Force Shock Test 6 70 60 5 50 4 40 3 30 2 20 1 10 0 0 1 2 Test 3 G-Force 80 Hammer Drop (ft.) 6 Frequency (Hz) G-Force Vibration Test 100 Hammer Drop (ft) G-Force Lowest Installed Cost Factors that influence installation time include assembly time, thread force, and reliability of tooling. Panduit tools and ties combine to speed installation time and deliver the lowest installed cost. Use the following tables as a guide to select Pan-Steel® solutions and tooling. Controlled Tension Installation Tool Life Cyle Comparison Reliability 160,000 140,000 Cycles to Failure Cycles to Failure The following is an example of Life Cycle Comparison Data demonstrating the superiority of Panduit tooling, with a very low failure rate, versus a leading competitor. Life Cycle Performance may very depending on environment and use. 120,000 Controlled Tension Installation Tool Life Cyle Comparison 100,000 Panduit GS4MT Competitor A 160,000 80,000 140,000 60,000 120,000 40,000 Panduit GS4MT 100,000 20,000 80,000 0 Test 1 60,000 Test 2 Sample 40,000 Thread Force 20,000 Thread Force (Lbs.) 0 Thread force is the measurement of force required to insert the end of a cable tie into the head. Panduit cable ties feature low thread force for extremely fast installation, improved productivity, and worker safety. Competitor A Test 3 Thread Force Comparison 12 10 Test 1 Test 2 Test 3 Sample 8 6 4 2 0 Panduit Competitor B Manufacturer Installation Time Assembly Time 12% s Saving 45 Time (minutes) 40 Time (minutes) Panduit ties, strap, and banding are fast to assemble and install versus standard banding. 50 35 30 50 25 45 20 40 15 35 10 30 5 25 0 20 15 65% s Saving 65% s Saving Panduit MLT 51% s Saving 8% s Saving Installation Time 12% s Saving Time to Install 8% s Saving Assembly 51% s Saving Time to Install Assembly Panduit Strap (Pre-Assembled) Panduit MLT Banding Panduit Strap (Coil) Competitor B Strapping 10 Workplace Safety and Abrasion Protection 5 0 Panduit Panduit Panduit Panduit Strap MLT MLT Strap Panduit stainless steel solutions feature fully rounded edges and a flush Banding cutoff to protect (Pre-Assembled) (Coil) the bundle from abrasion during and after installation. Both of these features are also critical to ensuring worker safety. On the job injuries due to laceration caused by a sharp edge or poor cut-off have several associated costs. The Occupational Health and Safety Organization (OSHA) reports that dollars spent on direct injuries are a fraction of the total costs of a lost time incident, other costs incudes: •Productive time lost by an injured employee and impacted supervisors •Cost of continuing all or part of the employee’s wages •Increased workers’ compensation insurance rates •Time to hire or to retrain other individuals to replace the injured worker •Time and cost for repair or replacement of any damaged equipment or materials •Clean up and start up of operations interrupted by the accident The costs associated with these factors can approach $10,000 per laceration. Competitor B Strapping Panduit Competitor A Cross sectional view of Panduit tie body versus competitor - magnified 150X - www.panduit.com 11 Product Selection Guides Pan-Steel® Stainless Steel Ties Self-Locking Head Construction *Aggressive locking head Quicker locking, tighter installation Unique locking ramp Assures locking in any position *Lead In Design Wider entrance for easier threading Extended retaining tab Increases overall tie strength *Innovative displacement lock Assures superior locking strength Cable Ties Variables such as chemical concentration, temperature, stress and ultra-violet light have differing effects on stainless steel. Each of these factors contributes to the useful life of a cable tie or tag. Cable tie selection depends on the resiliency of the object in your application. MLT ties are ideally suited for resilient Cable Bundling Applications. MRT application ties, MRS ties and strapping are recommended for non-resilient Mechanical Fastening Applications. Use the following table as a guide to select the appropriate tie for your applications. *Patented Length Part Number Material In. mm Width Min. Loop Tensile Strength In. mm Lbs. N Application Stainless Steel Self-Locking Cable Ties Retained Tension Ties (MRT and MRS Series) *Displacement Lock Assures superior locking strength **Lead In Wider entrance for easier threading *Aggressive Locking Head Quicker locking, tighter installation Unique Locking Ramp Assures locking in any position Relief Slots For improved bundle conformance *Patented **Patent Pending Additional Features of 360° Radial Seal Retained Tension Ties (MRS Series Only) Standard Cross Section MLT2S-CP 304SS 7.9 201 0.18 4.6 200 890 Identification MLT2S-CP316 316SS 7.9 201 0.18 4.6 200 890 MLT4S-CP MLT4S-CP316 304SS 316SS 14.3 14.3 362 362 0.18 0.18 4.6 4.6 200 200 890 890 Identification, extra corrosion resistance Identification Identification, extra corrosion resistance Heavy Cross Section MLT2H-LP 304SS 7.9 201 0.31 7.9 450 2000 MLT2H-LP316 MLT4H-LP 316SS 304SS 7.9 14.3 201 362 0.31 0.31 7.9 7.9 450 450 2000 2000 MLT4H-LP316 General Purpose, Aerial support, Identification Cable tray (indoors/outdoors) General Purpose, Aerial support, Identification Cable tray (indoors/outdoors) 316SS 14.3 362 0.31 7.9 450 2000 Extra-Heavy Cross Section MLT4EH-LP 304SS 17.1 434 0.50 12.7 600 2670 MLT4EH-LP316 MLT6EH-LP 17.1 23.4 434 594 0.50 0.50 12.7 12.7 600 600 2670 2670 MLT6EH-LP316 316SS Extra-Heavy 15 Cross Section MLT8EH15-LP 304SS MLT12EH15-Q 304SS Super-Heavy Cross Section MLT4SH-LP316 316SS MLT6SH-LP316 316SS MLT6DSH-Q316 316SS 23.4 594 0.50 12.7 600 2670 Aerial support, Cable tray (indoors/outdoors) Cable tray (indoors/outdoors) Aerial support, Cable tray (indoors/outdoors) Cable tray (indoors/outdoors) 29.7 42.2 754 1072 0.50 0.50 12.7 12.7 700 700 3115 3115 Pipe insulation Pipe insulation 17.1 23.4 41.5 434 594 1054 0.63 0.63 0.63 15.9 15.9 15.9 900 900 1200 4005 4005 5340 MLT8DSH-Q316 53.5 1359 0.63 15.9 1200 5340 Shipboard Cable Bundling Shipboard Cable Bundling Double Loop short circuit – up to 71.5kA Double Loop short circuit – up to 71.5kA 316SS 304SS 316SS Stainless Steel Retained Tension Ties **Front Tab Improves bundle conformance Extra Long Body Improves bundle conformance Heavy Cross Section MRT2H-L4 304SS 11.3 287 0.31 7.9 400 1780 MRT4H-L4 17.6 447 0.31 7.9 400 1780 304SS Heat Shields and General Mechanical Heat Shields and General Mechanical Stainless Steel 360° Radial Seal Retained Tension Ties **Patent Pending Standard Cross Section MRS1S-C4 304SS MRS4S-C4 304SS Light-Heavy Cross Section MRS1.5LH-L4 304SS MRS4LH-L4 304SS 10.6 18.5 269 470 0.18 0.18 4.4 4.4 180 180 800 800 Rubber Boots, Hoses Rubber Boots, Hoses 9.7 18.5 246 470 0.25 0.25 6.4 6.4 225 225 1000 1000 Rubber Boots, Hoses Rubber Boots, Hoses Pan-Alum® Aluminum Self-Locking Cable Ties Heavy Cross Section 12 www.panduit.com MLT1H-LPAL Aluminum 5.5 140 0.31 7.9 50 222 Identification MLT2H-LPAL Aluminum 7.9 201 0.31 7.9 50 222 Identification MLT4H-LPAL Aluminum 14.3 362 0.31 7.9 50 222 Identification Refer to tool selection guide on page 13 for recommended tool. Representative offering only, consult www.panduit.com for complete listing of products. Cable Ties (continued) Length Part Number In. Material mm Width In. Panduit Min. Loop Tensile Strength mm Lbs. N Application Cable tray (indoor/ outdoor), Telco backbone Cable tray (indoor/ outdoor), Telco backbone Fully Coated Stainless Steel Self-Locking Cable Ties Standard Cross Section MLTFC2S-CP316 Coated 316SS MLTFC4S-CP316 Coated 316SS Heavy Cross Section MLTFC2H-LP316 Coated 316SS MLTFC4H-LP316 Coated 316SS Extra-Heavy Cross Section MLTFC4EH-LP316 Coated 316SS MLTFC6EH-LP316 Coated 316SS Super-Heavy Cross Section MLTFC4SH-LP316 Coated 316SS MLTFC6SH-LP316 Coated 316SS stainless steel cable ties and 7.9 201 0.18 4.6 100 445 14.3 362 0.18 4.6 4100 445 7.9 201 0.31 7.9 250 1112 14.3 362 0.31 7.9 250 1112 17.1 434 0.50 12.7 300 1335 Shipboard Cable Bundling 23.4 594 0.50 12.7 300 1335 Shipboard Cable Bundling 17.1 434 0.63 15.9 450 2000 Shipboard Cable Bundling 23.4 594 0.63 15.9 450 2000 Shipboard Cable Bundling installations. Pan-Steel® Stainless Steel Strapping Unique Locking Methods* tooling deliver Cable tray (indoors/outdoors) Cable tray (indoors/outdoors) safe, fast, and reliable Discrete and Custom Length Strapping and Loose Piece Head MS6W75T30-Q6 MS8W75T30-Q6 MS10W75T30-Q6 MSCNW50T15-QR6 316SS 316SS 316SS Coated 316SS MSW75T30-CR2 201SS MSBW50-C6 MSBW75-C2 Cushion Sleeve PCSSH-B-CR 316SS 201SS PCSLSH-B-CR 26.5 32.7 39.0 82.5 Ft. 100 Ft. N/A N/A 673 831 991 25.0 m 30.5 m N/A N/A 0.75 0.75 0.75 0.50 19.1 19.1 19.1 12.7 2400 2400 2400 700 10656 10656 10656 3115 Sign and Signal Mounting Sign and Signal Mounting Sign and Signal Mounting Instrument tubing 0.75 19.1 2400 10656 Sign and Signal Mounting N/A N/A N/A N/A N/A N/A N/A N/A Instrument tubing Sign and Signal Mounting 100 Ft. 100 Ft 30.5 m 30.5 0.91 23.1 N/A N/A Cable tray (indoor/outdoor) military applications 1.05 26.5 N/A N/A Cable tray (indoor/outdoor) military applications Neoprene TPE Low Smoke HalogenFree and Flame Retardant *Patented *Patent Pending The buckle design and tension controlled installation tool offers a quick and safe installation for all harsh environments. Representative offering only, consult www.panduit.com for complete listing of products. Installation Tools PPTMT Part Number PBTMT Tie/Strap Size GS4MT RT2HT RT2HTN Best for Annual Usage Controlled Tension Cut-off Manual/ Powered Time to Install PPTMT Standard, Light-Heavy, Heavy, MLT Over 50,000 Yes Auto Cut-Off Powered Best PBTMT Heavy, Extra-Heavy, SuperHeavy, MLT Over 50,000 Yes Auto Cut-Off Powered Best GS4MT Standard, Light-Heavy, Heavy, MLT Under 50,000 Yes Auto Cut-Off Manual Better RT2HT Extra-Heavy and Super-Heavy, MLT Under 50,000 Yes Lever Cut-Off Manual Better RT2HTN Extra-Heavy and Super-Heavy, MLT Under 50,000 Yes Narrow Nose Lever Cut-Off Manual Better ST2MT Standard, Light-Heavy, Heavy, Extra Heavy, MLT Under 10,000 No Twist Cut-Off Manual Better MTRTH Heavy, MRT/MRS Under 50,000 Yes Lever Cut-Off Manual Good BT2HT 3/8, 1/2 and 5/8 Wide Strapping Under 50,000 Yes Auto Cut-Off Manual Good BT75SDT 3/4, Wide Strapping Under 50,000 No Lever Cut-Off Manual Good *Contact customer service for high volume applications. ST2MT MTRTH BT2HT BT75SDT www.panduit.com 13 Permanent Identification System Panduit permanent identification solutions offer flexibility and long service life. MMP350-C316 Length Part Number Material Color In. Width mm In. mm Max. Recommended 3/16" Tie Cross (4.77mm) Section Characters Max. per Line Lines Standard Heavy Metal Marker Plates – Dual Cable Tie Installation Stainless Steel Marker Plates MMP350-C 304SS MMP350-C316 316SS MMP350H-C 304SS MMP350H-C316 316SS MMP350W38-C 304SS MMP350W38-C316 316SS MMP172-C 304SS MMP172-C316 316SS MMP172W38-C 304SS MMP172W38-C316 316SS Aluminum Marker Plates Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural 3.50 3.50 3.50 3.50 3.50 3.50 1.72 1.72 1.72 1.72 89.0 89.0 89.0 89.0 89.0 89.0 44.0 44.0 44.0 44.0 0.75 0.75 0.75 0.75 0.38 0.38 0.75 0.75 0.38 0.38 19.0 19.0 19.0 19.0 10.0 10.0 19.0 19.0 10.0 10.0 23 23 20 20 20 20 8 8 8 8 3 3 3 3 1 1 3 3 1 1 X X MMP350H-CAL Aluminum Natural MMP350HW54-MAL Aluminum Natural 3.50 3.50 89.0 89.0 0.75 0.54 19.0 13.7 20 16 3 2 0.75 0.75 0.75 0.75 N/A N/A N/A 19.0 19.0 19.0 19.0 N/A N/A N/A 26 26 10 10 5 5, 6, 5 6, 12, 8 3 3 3 3 1 3 3 X X X X X X X N/A N/A N/A N/A N/A N/A 5 5, 6, 5 6, 12, 8 1 3 3 X X X X X X X X X X X X X Metal Tags – Single Cable Tie Installation Stainless Steel Tags MMP350W38-C316 MMP350H-C MTB150D-Q MT350-C MT350-C316 MT172-C MT172-C316 MT1D-Q MT150D-Q MT213D-Q Brass Tags MTB1D-Q MTB150D-Q MTB213D-Q 304SS 316SS 304SS 316SS 304SS 304SS 304SS Brass Brass Brass Natural 3.50 89.0 Natural 3.50 89.0 Natural 1.72 44.0 Natural 1.72 44.0 Natural 1.00* 25.0** Natural 1.50* 38.0** Natural 2.13* 54.0** Brass Brass Brass 1.00* 25.0** 1.50* 38.0* 2.13* 54.0** *Diameter (In.) **Diameter (mm). Representative offering only, consult www.panduit.com for complete listing of product. On-Site Custom Marking Tools Part Number MEHT187 MEHT187 MIM094 MIM125 MIM187 PES197 Hand or Tabletop Hand Volume Low Marking Type Embossing Tabletop Medium Indenting Tabletop High Embossing Marker Materials Metal Tape: Stainless Steel, Aluminum Marker Plates or Tags: Stainless Steel, Aluminum, Brass Marker Plates: Stainless Steel, Aluminum Character Fonts 3/16 (4.77mm) 3/32 (2.38mm) 1/8 (3.18mm) 3/16 (4.77mm) 3/16 (4.77mm) Custom Marking Service MIM PES197 14 www.panduit.com Panduit Factory Custom Marking Service simplifies identification with high quality, made-to-order custom embossed marker plates and tags or laser etched cable ties, marker plates, and tags. To select and order custom embossed marker plates and tags use on-line order form (C2-0677) at www.panduit.com/permanentid. Panduit offers fast turn around on custom marking orders worldwide. Partner with Panduit to create an effectively identified workplace. Compliance with Industry Standards Panduit stainless steel cable ties, strapping, and installation tools meet and exceed the most stringent industry standards. Refer to the following chart for approvals and corresponding products. Contact Panduit for additional information and approvals. Pan-Steel® System Approvals Logo (Symbol) Agency Spec/Approval Requirement Applicable Products Underwriters Laboratories, Inc. Listing E56854 Dimensional, tensile, temp., cycling, humidity MLT-S, MLT-LH, MLT-H, MLTEH15, MLT-SH, MLTDEH, MLTDSH IN 304 and 316. MSW38T15, MTW50T15, MSW63T15, MSBW38, MSBW50, MSBW63 IN 304 and 316. MSCW38T15, MSCW50T15, MSCW63T15, MLTFCS, MLTFCSH, MLTCH, MSCNW38T15, MSCNW5015, MSCNW63T15 in 316 material Conformite European Low Voltage Directive 2006/95/EC MLT cable ties and MS straps also meet the requirements from EN62275 CE Marking is required for products sold within the European Union. CE Marking Directives specify the minimum performance of these products. Applying the CE mark signifies compliance with essential requirements of specific directives All MLT, MRT, MRS ties and MS straps Cert. # HS118592C HS373867 HS152579 HS476898 HS118592A HS118592B Mechanical All MLT ties and MS straps Bureau Veritas Cert. # 04048/E1 Material specification, dimensional, visual All coated and uncoated MLT ties. All MS Straps uncoated and nylon coated Det Norske Veritas Cert. # E-12387 E-12388 Salt mist test, tensile test, accelerated aging, vibration tests All uncoated MLTS, MLTH, MLTE15, MLTDEH15, MLMTSH, and MS strap coated and uncoated 316 material Germanischer Lloyd Cert. # 32666-83HH 51796-89HH Mechanical All coated and uncoated Stainless Steel MLT ties. MS Straps uncoated and nylon coated 316 material Lloyd’s Register of Shipping Cert. # 89/60123 Material specification, tensile test, vibration tests All coated and uncoated stainless steel MLT ties and MS strap SAE Int’l formerly US MIL AS23190 formerly MS23109E Dimensional, visual, vibration, temp. cycling, immersion MLT-S and MLT-H ties in 304 and 316 material US Coast Guard File No. 16703/46 Mechanical MLT-H series cable ties US Military MIL-T-81306A/ MS90387-3 Mechanical GS4MT installation tools Amer. Bureau of Shipping Panduit ® Pan-Steel ® Stainless Steel Systems meet and exceed the most stringent industry standards. www.panduit.com 15 Panduit Difference Industrial Oil Rigs • Refineries • Chemical Plants • Water Treatment Facilities • Wind Farms • Solar • Nuclear • Mining • Ships • Submarines • Cell Towers • Aerial Support • Telecommunications • Transportation • OEM • • WORLDWIDE SUBSIDIARIES AND SALES OFFICES At Panduit, servicing customers is a top priority. Our world-class sales force and comprehensive customer service and technical support provide dedicated and market-focused expertise to assist you in evaluating, designing, implementing, and purchasing the products and services you need to solve your unique business challenges. Customers count on the Panduit service advantage and global product availability to keep their projects on schedule and on budget. Whether you need product information, on-site application guidance, answers to technical questions, or a referral to one of our best-in-class partners, Panduit representatives are highly trained to provide the required assistance. The Panduit website (www.panduit.com) provides access to interactive roadmaps, design tools, product specifications, technical guides and extensive downloads to help you select, design, and install Panduit solutions. The website also helps you connect with local Panduit service experts and distributors. Complete Solutions from Panduit Panduit harsh environment solutions include the Pan-Steel® System, power and grounding connectors, identification and safety, abrasion protection, heat shrink, wiring duct, industrial ethernet, and cable tie solutions. These solutions feature Panduit world-class quality, rigorously tested to deliver the highest performance, and lowest total cost of ownership. Panduit Canada Markham, Ontario [email protected] Phone: 800.777.3300 Panduit Europe Ltd. London, UK [email protected] Phone: 44.208.601.7200 Panduit Singapore Pte. Ltd. Republic of Singapore [email protected] Phone: 65.6305.7575 Panduit Japan Tokyo, Japan [email protected] Phone: 81.3.3767.7011 Stainless Steel System Power Connectors Grounding System Identification and Safety Abrasion Protection Heat Shrink Wiring Duct Industrial Ethernet Cable Ties Panduit Latin America Guadalajara, Mexico [email protected] Phone: 52.33.3777.6000 Panduit Australia Pty. Ltd. Victoria, Australia [email protected] Phone: 61.3.9794.9020 For a copy of Panduit product warranties, log on to www.panduit.com/warranty For more information Visit us at www.panduit.com Contact Customer Service by email: [email protected] or by phone: 800-777-3300 ©2015 Panduit Corp. ALL RIGHTS RESERVED. Printed in the U.S.A. SSAG04--SA-ENG Replaces SA-SSAG03 11/2015