A3425: Ultra-Sensitive Dual-Channel Quadrature Hall-Effect Bipolar Switch

A3425
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
Discontinued Product
This device is no longer in production. The device should not be
purchased for new design applications. Samples are no longer available.
Date of status change: May 2, 2011
Recommended Substitutions:
For existing customer transition, and for new customers or new applications, refer to the A1230.
NOTE: For detailed information on purchasing options, contact your
local Allegro field applications engineer or sales representative.
Allegro MicroSystems, LLC reserves the right to make, from time to time, revisions to the anticipated product life cycle plan
for a product to accommodate changes in production capabilities, alternative product availabilities, or market demand. The
information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use; nor for any infringements of patents or other rights of third parties which may result from its use.
A3425
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
Features and Benefits
Description
▪
▪
▪
▪
▪
The A3425 is a dual–output-channel, bipolar switch with each
channel comprising a separate complete Hall-effect circuit with
dedicated Hall element and separate digital output for speed
and direction signal processing capability. The independent
Hall elements (E1 integrated with OUTPUTA, and E2 integrated
with OUTPUTB) are photolithographically aligned to better
than 1 μm. Maintaining this accurate mechanical location
between the two active Hall elements eliminates the major
manufacturing hurdle encountered in fine-pitch detection
applications. The A3425 is a highly sensitive, temperature-stable
magnetic device, which is ideal for use in ring magnet-based
speed and direction sensing systems used in harsh automotive
and industrial environments.
Two matched Hall effect switches on a single substrate
Hall element spacing approximately 1 mm
Superior temperature stability
3.3 to 18 V operation
Integrated ESD diode from OUTPUT and VCC pins
to GND
▪ High-sensitivity switchpoints
▪ Robust structure for EMC protection
▪ Solid-state reliability
Package: 8 pin SOIC (suffix L), and 4 pin
SIP (suffix K)
The A3425 contains two independent Hall effect switches, and
has a monolithic IC that accurately locates the two Hall elements,
E1 and E2, approximately 1 mm apart. The digital outputs are
90º out of phase so that the outputs are in quadrature, with the
proper ring magnet design. This allows for easy processing of
speed and direction signals. Extremely low-drift amplifiers
guarantee symmetry between the switches to maintain signal
Continued on the next page…
Not to scale
Typical Application
VOUTPUTB
VOUTPUTA
2
OUTPUTA
VSupply
A3425
1
VCC
OUTPUTB
100 Ω
GND
4
0.1 uF
Using unregulated supply
A3425DS-Rev. 13
3
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
Description (continued)
quadrature. The patented chopper stabilization technique cancels
offsets in each channel, and provides stable operation over the
operating temperature and voltage ranges. An on-chip regulator
allows the use of this device over a wide operating voltage range.
Post-assembly factory programming provides sensitive switchpoints
that are symmetrical between the two switches.
The A3425 is available in a plastic 8-pin SOIC surface mount
package (L) and a plastic 4-pin SIP (K), both in two operating
temperature ranges. Each package is available in a lead (Pb) free
version with 100% matte tin plated leadframe.
Selection Guide
Part Number
Packing*
Mounting
A3425EK-T
Bulk, 500 pieces/bag
4-pin SIP through hole
A3425LK-T
Bulk, 98 pieces/bag
4-pin SIP through hole
A3425LLTR-T
13-in. reel, 3000 pieces/reel
8-pin SOIC surface mount
Ambient, TA
–40ºC to 85ºC
–40ºC to 150ºC
*Contact Allegro for additional packing options.
Absolute Maximum Ratings
Characteristic
Symbol
Notes
Rating
Units
Supply Voltage
VCC
26.5
V
Reverse Battery Voltage
VRCC
–16
V
V
Output Off Voltage
VOUTPUT
VCC
IOUTPUT(Sink)
Internally Limited
–
Magnetic Flux Density
B
Unlimited
–
Operating Ambient Temperature
TA
Maximum Junction Temperature
Output Sink Current
Storage Temperature
Range E
–40 to 85
ºC
Range L
–40 to 150
ºC
TJ(max)
165
ºC
Tstg
–65 to 170
ºC
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
2
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
Functional Block Diagram
VCC
Programmable
Trim
Regulator
8 Bits
Channel A
Amp
OUTPUTA
Sample and Hold
Dynamic Offset
Cancellation
4 Bits
Hall
Element
E1
LowPass
Filter
Output
Drive
Channel B
Amp
OUTPUTB
Sample and Hold
Hall
Element
E2
Dynamic Offset
Cancellation
4 Bits
LowPass
Filter
Output
Drive
GND
Terminal List Table
Package K
E1
Package L
1
E2
2
3
1
2
3
4
4
E1
E2
8
7
6
5
Pin Number
Name
Function
Package K
Package L
1
1
2
2
OUTPUTA Output from E1 via first Schmitt circuit
3
3
OUTPUTB Output from E2 via second Schmitt circuit
4
4
GND
–
5-8
NC
VCC
Connects power supply to on-chip voltage regulator
Terminal for ground connection
No connection
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
3
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
OPERATING CHARACTERISTICS Valid over operating temperature ranges unless otherwise noted; typical data applies to
VCC = 12 V, and TA = 25ºC
Characteristic
Symbol
Test Conditions
Min. Typ.
Max
Units
ELECTRICAL CHARACTERISTICS
Supply Voltage1
VCC
Output Leakage Current
IOUTPUT(OFF)
Operating; TA ≤ 150°C
3.3
–
18
V
Either output
–
<1
10
μA
Output Rise Time
tr
CLOAD = 20 pF, RLOAD = 820 Ω
–
1.8
–
μs
Output Fall Time
tf
CLOAD = 20 pF, RLOAD = 820 Ω
–
1.2
–
μs
ICC(OFF)
B < BRP(A) ,B < BRP(B)
–
3.5
6.0
mA
ICC(ON)
B > BOP(A) ,B > BOP(B)
–
4.0
6.0
mA
Both outputs; IOUTPUT(SINK) = 20 mA; B > BOP(A),
B > BOP(B)
–
160
500
mV
–
–
20
mA
Supply Current
Low Output Voltage
VOUTPUT(ON)
Output Sink Current
Output Sink Current,
IOUTPUT(SINK)
Continuous2
Output Sink Current, Peak3
Chopping Frequency
IOUTPUT(SINK)C
TJ < TJ(max) ,VOUTPUT = 12 V
–
–
70
mA
IOUTPUT(SINK)P
t < 3 seconds
–
–
220
mA
–
340
–
kHz
fC
TRANSIENT PROTECTION CHARACTERISTICS
Supply Zener Voltage
VZ
ICC = 15 mA
28
33
37
V
Supply Zener Current4
IZ
VS = 28 V
–
–
9.0
mA
VRCC = –18 V, TJ < TJ(max)
–
2
15
mA
Reverse-Battery Current
IRCC
Continued on the next page...
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
4
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
OPERATING CHARACTERISTICS (continued) Valid over operating temperature ranges unless otherwise noted; typical
data applies to VCC = 12 V, and TA = 25ºC
Characteristic
MAGNETIC CHARACTERISTICS, K
Symbol
Test Conditions
Min. Typ.
Max
Units
Package5
Operate Point: B > BOP
BOP(A), BOP(B)
–
7
35
G
Release Point: B < BRP
BRP(A), BRP(B)
–35
–7
–
G
BHYS(A), BHYS(B)
5
16
40
G
SYMA, SYMB
–40
–
40
G
Operate Symmetry: BOP(A) – BOP(B)
SYMAB(OP)
–30
–
30
G
Release Symmetry: BRP(A) – BRP(B)
SYMAB(RP)
–30
–
30
G
Hysteresis: BOP(A) – BRP(A),
BOP(B) – BRP(B)
Symmetry: Channel A, Channel B,
BOP(A) + BRP(A), BOP(B) + BRP(B)
MAGNETIC CHARACTERISTICS, L Package5
Operate Point: B > BOP
BOP(A), BOP(B)
–
7
30
G
Release Point: B < BRP
BRP(A), BRP(B)
–30
–7
–
G
BHYS(A), BHYS(B)
5
14
35
G
SYMA, SYMB
–35
–
35
G
Operate Symmetry: BOP(A) – BOP(B)
SYMAB(OP)
–25
–
25
G
Release Symmetry: BRP(A) – BRP(B)
SYMAB(RP)
–25
–
25
G
Hysteresis: BOP(A) – BRP(A),
BOP(B) – BRP(B)
Symmetry: Channel A, Channel B,
BOP(A) + BRP(A), BOP(B) + BRP(B)
1
When operating at maximum voltage, never exceed maximum junction temperature, TJ(max). Refer to power derating curve charts.
Device will survive the current level specified, but operation within magnetic specification cannot be guaranteed.
3 Short circuit of the output to VCC is protected for the time duration specified.
4 Maximum specification limit is equivalent to I
CC(max) + 3 mA.
5 Magnetic flux density, B, is indicated as a negative value for north-polarity magnetic fields, and as a positive value for south-polarity
magnetic fields. This so-called algebraic convention supports arithmetic comparison of north and south polarity values, where the
relative strength of the field is indicated by the absolute value of B, and the sign indicates the polarity of the field (for example, a
–100 G field and a 100 G field have equivalent strength, but opposite polarity).
2
EMC
Contact Allegro MicroSystems for EMC performance.
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
5
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
THERMAL CHARACTERISTICS may require derating at maximum conditions, see application information
Characteristic
Symbol
Test Conditions*
RθJA
Package Thermal Resistance
Value Units
Package K, 1-layer PCB with copper limited to solder pads
177
ºC/W
Package L-8 pin, 1-layer PCB with copper limited to solder pads
140
ºC/W
Package L-8 pin, 4-layer PCB based on JEDEC standard
80
ºC/W
*Additional thermal data available on the Allegro Web site.
Maximum Allowable VCC (V)
Power Derating Curve
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
VCC(max)
Package L, 4-layer PCB
(RθJA = 80 ºC/W)
Package L, 1-layer PCB
(RθJA = 140 ºC/W)
Package K, 1-layer PCB
(RθJA = 177 ºC/W)
VCC(min)
20
40
60
80
100
120
140
160
180
Temperature (ºC)
Power Dissipation, PD (m W)
Power Dissipation versus Temperature
1900
1800
1700
1600
1500
1400
1300
1200
1100
1000
900
800
700
600
500
400
300
200
100
0
P
(R ack
ag
θJ
A = e
80 L, 4
ºC -la
/W ye
Pa
cka
) rP
(R
ge
C
θJA
B
L
= 1 , 1lay
40
ºC er P
/W
CB
Pac
)
(R kage K
θJA =
, 1la
177
ºC/ yer PC
W)
B
20
40
60
80
100
120
140
Temperature, TA (°C)
160
180
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
6
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
Functional Description
Chopper-Stabilized Technique
When using Hall effect technology, a limiting factor
for switchpoint accuracy is the small signal voltage
developed across the Hall element. This voltage is disproportionally small relative to the offset that can be
produced at the output of the Hall device. This makes
it difficult to process the signal and maintain an accurate, reliable output over the specified temperature and
voltage range.
Chopper stabilization is a unique approach used to
minimize Hall offset on the chip. The patented Allegro
technique, dynamic quadrature offset cancellation,
removes key sources of the output drift induced by
thermal and mechanical stress. This offset reduction
technique is based on a signal modulation-demodulation process. The undesired offset signal is separated
from the magnetically induced signal in the frequency
domain through modulation. The subsequent demodulation acts as a modulation process for the offset,
causing the magnetically-induced signal to recover its
original spectrum at the baseband level, while the dc
offset becomes a high-frequency signal. Then, using a
low-pass filter, the signal passes while the modulated
dc offset is suppressed.
The chopper stabilization technique uses a 170 kHz
high-frequency clock. The Hall element chopping
occurs on each clock edge, resulting in a 340 kHz
chop frequency. This high-frequency operation allows
for a greater sampling rate, which produces higher
accuracy and faster signal processing capability. This
approach desensitizes the chip to the effects of thermal and mechanical stress. The disadvantage to this
approach is that jitter, also known as 360° repeatability,
can be induced on the output signal. The sample-andhold process, used by the demodulator to store and
recover the signal, can slightly degrade the signalto-noise ratio. This is because the process generates
replicas of the noise spectrum at the baseband, causing
a decrease in jitter performance. However, the improvement in switchpoint performance, resulting from the
reduction of the effects of thermal and mechanical
stress, outweighs the degradation in the signal-to-noise
ratio.
This technique produces devices that have an
extremely stable quiescent Hall element output voltage, are immune to thermal stress, and have precise
recoverability after temperature cycling. This technique is made possible through the use of a BiCMOS
process, which allows the use of low-offset and lownoise amplifiers in combination with high-density
logic integration and sample-and-hold circuits. This
process is illustrated in the following diagram.
Amp
Sample and Hold
Regulator
LowPass
Filter
Chopper stabilization circuit (dynamic quadrature offset cancellation)
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
7
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
Typical Applications Operation
Switch to High
VOUTPUT(OFF)
Switch to Low
VOUTPUT
V+
VOUTPUT(ON)(sat)
BRP
BOP
B+
BHYS
Output voltage in relation to magnetic flux density received.
Output on each channel independently follows the same
pattern of transition through BOP followed by transition
through BRP.
Channel A
M agnetic Field
at Hall Element E1
Channel B
M agnetic Field
at Hall Element E2
Channel A
Output Signal
at OUTPUTA
Channel B
Output Signal
at OUTPUTB
Quadrature output signal configuration. The outputs of the two
output channels have a phase difference of 90º when used
with a properly designed magnet that has an optimal pole pitch
of twice the Hall element spacing of 1.0 mm.
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
8
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
Typical Applications Circuits
This device requires minimal protection circuitry
during operation with a low-voltage regulated line.
The on-chip voltage regulator provides immunity
to power supply variations between 3.3 and 18 V.
Because the device has open-drain outputs, pull-up
resistors must be included.
protection is generally required to protect the device
against supply-side transients. Specifications for such
transients vary for each application, so the design of
the protection circuit should be optimized for each
application.
If protection against coupled and injected noise is
required, then a simple low-pass filter on the supply
(RC) and a filtering capacitor on each of the outputs
may also be needed, as shown in the unregulated
supply diagram.
For applications in which the device receives its power
from unregulated sources, such as a car battery, full
For example, the circuit shown in the unregulated
supply diagram includes a Zener diode that offers high
voltage load-dump protection and noise filtering by
means of a series resistor and capacitor. In addition, it
includes a series diode that protects against high-voltage reverse battery conditions.
VOUTPUTB
VOUTPUTA
2
OUTPUTA
VSupply
A3425
1
VCC
3
OUTPUTB
GND
0.1 uF
4
Regulated supply
VOUTPUTB
VOUTPUTA
2
OUTPUTA
VSupply
A3425
1
VCC
3
OUTPUTB
100 Ω
GND
4
0.1 uF
Unregulated supply
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
9
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
Typical Thermal Performance
The device must be operated below the maximum junction
temperature of the device, TJ(max). Under certain combinations of
peak conditions, reliable operation may require derating supplied power or improving the heat dissipation properties of the
application. This section presents a procedure for correlating
factors affecting operating TJ. (Thermal data is also available on
the Allegro MicroSystems Web site.)
The Package Thermal Resistance, RJA, is a figure of merit summarizing the ability of the application and the device to dissipate
heat from the junction (die), through all paths to the ambient air.
Its primary component is the Effective Thermal Conductivity,
K, of the printed circuit board, including adjacent devices and
traces. Radiation from the die through the device case, RJC, is
relatively small component of RJA. Ambient air temperature,
TA, and air motion are significant external factors, damped by
overmolding.
The effect of varying power levels (Power Dissipation, PD), can
be estimated. The following formulas represent the fundamental
relationships used to estimate TJ, at PD.
PD = VIN × IIN

(1)
T = PD × RJA (2)
TJ = TA + ΔT
Example: Reliability for VCC at TA = 150°C, package L, using
minimum-K PCB
Observe the worst-case ratings for the device, specifically:
RJA = 140 °C/W, TJ(max) = 165°C, VCC(max) = 18 V, and
ICC(max) = 6 mA.
Calculate the maximum allowable power level, PD(max). First,
invert equation 3:
Tmax = TJ(max) – TA = 165 °C – 150 °C = 15 °C
This provides the allowable increase to TJ resulting from internal
power dissipation. Then, invert equation 2:
PD(max) = Tmax ÷ RJA = 15°C ÷ 140 °C/W = 107 mW
Finally, invert equation 1 with respect to voltage:
VCC(est) = PD(max) ÷ ICC(max) = 107 mW ÷ 6 mA = 18 V
The result indicates that, at TA, the application and device can
dissipate adequate amounts of heat at voltages ≤VCC(est).
Compare VCC(est) to VCC(max). If VCC(est) ≤ VCC(max), then reliable operation between VCC(est) and VCC(max) requires enhanced
RJA. If VCC(est) ≥ VCC(max), then operation between VCC(est) and
VCC(max) is reliable under these conditions.
(3)
For example, given common conditions such as: TA= 25°C,
VCC = 12 V, ICC = 4 mA, and RJA = 140 °C/W, then:
PD = VCC × ICC = 12 V × 4 mA = 48 mW

T = PD × RJA = 48 mW × 140 °C/W = 7°C
TJ = TA + T = 25°C + 7°C = 32°C
A worst-case estimate, PD(max), represents the maximum allowable power level (VCC(max), ICC(max)), without exceeding TJ(max),
at a selected RJA and TA.
10
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
Electrical Operating Characteristics, Package L
ICC(off)
8
8
7
7
6
6
5
-40°C
4
25°C
3
150°C
2
Current (mA)
Current (mA)
ICC(off)
1
3.3 V
18 V
5
4
3
2
1
0
0
0
5
10
15
-50
20
0
50
ICC(on)
150
200
ICC(on)
8
7
7
6
6
5
-40°C
4
25°C
3
150°C
2
Current (mA)
8
1
5
3.3 V
4
18 V
3
2
1
0
0
5
10
15
0
20
-50
0
50
100
150
200
Temperature (°C)
VCC (V)
Output Saturation Voltage
VCC = 3.3 V, Isink = 20 mA
500
400
Vsat (mV)
Current (mA)
100
Temperature (°C)
VCC (V)
Ch. A
300
Ch. B
200
100
0
-50
0
50
100
150
200
Temperature (°C)
11
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
Magnetic Operating Characteristics, Package L
Channel A, BOP and BRP
Channel A, BOP and BRP
30
30
20
BOP
10
0
-40°C
25°C
150°C
BRP
-10
-20
-30
0
5
10
15
Switchpoint (G)
Switchpoint (G)
20
0
0
100
150
200
Channel B, BOP and BRP
30
20
BOP
10
0
-40°C
25°C
150°C
BRP
-10
Switchpoint (G)
20
Switchpoint (G)
50
Temperature (°C)
30
-20
0
5
10
15
0
3.3 V
12 V
18 V
BRP
-10
-20
-30
-50
20
BOP
10
0
50
100
150
200
Temperature (°C)
VCC (V)
Channels A and B, Hysteresis
Channels A and B, Hysteresis
30
30
25
25
20
-40°C
25°C
150°C
15
10
BOP - BRP (G)
BOP - BRP (G)
18 V
-20
Channel B, BOP and BRP
20
3.3 V
12 V
18 V
15
10
5
5
0
12 V
BRP
VCC (V)
-30
3.3 V
-10
-30
-50
20
BOP
10
0
5
10
15
VCC (V)
20
0
-50
0
50
100
150
200
Temperature (°C)
Additional magnetic characteristics on next page
12
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
Magnetic Operating Characteristics, Package L (continued)
BOP Symmetry
BOP Symmetry
30
30
20
10
-40°C
0
25°C
150°C
-10
-20
-30
0
5
10
15
Ch. A - Ch. B (G)
Ch. A - Ch. B (G)
20
12 V
0
18 V
-10
-20
-30
-50
20
3.3 V
10
0
VCC (V)
20
20
10
-40°C
0
25°C
150°C
-10
-20
10
15
VCC (V)
20
Ch. A - Ch. B (G)
Ch. A - Ch. B (G)
30
5
150
200
BRP Symmetry
BRP Symmetry
0
100
Temperature (°C)
30
-30
50
10
3.3 V
0
12 V
-10
18 V
-20
-30
-50
0
50
100
150
200
Temperature (°C)
Additional magnetic characteristics on next page
13
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
Magnetic Operating Characteristics, Package L (continued)
Channel A Symmetry
30
30
20
20
10
-40°C
0
25°C
150°C
-10
-20
BOP + BRP (G)
BOP + BRP (G)
Channel A Symmetry
-30
0
5
10
15
10
12 V
-10
18 V
-20
-30
-50
20
3.3 V
0
0
VCC (V)
20
20
10
10
-40°C
0
25°C
-10
150°C
-20
-30
VCC (V)
15
20
BOP + BRP (G)
BOP + BRP (G)
30
10
150
200
Channel B Symmetry
30
5
100
Temperature (°C)
Channel B Symmetry
0
50
3.3 V
0
12 V
-10
18 V
-20
-30
-50
0
50
100
150
200
Temperature (°C)
14
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
Electrical Operating Characteristics, Package K
ICC(off)
8
8
7
7
6
6
5
-40°C
4
25°C
3
150°C
2
Current (mA)
Current (mA)
ICC(off)
1
3.3 V
18 V
5
4
3
2
1
0
0
0
5
10
15
-50
20
0
50
150
200
Temperature (°C)
VCC (V)
ICC(on)
ICC(on)
8
7
7
6
6
5
-40°C
4
25°C
3
150°C
2
Current (mA)
8
1
5
3.3 V
4
18 V
3
2
1
0
0
5
10
15
0
20
-50
0
50
100
150
200
Temperature (°C)
VCC (V)
Output Saturation Voltage
VCC = 3.3 V, Isink = 20 mA
500
400
Vsat (mV)
Current (mA)
100
Ch. A
300
Ch. B
200
100
0
-50
0
50
100
150
200
Temperature (°C)
15
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
Magnetic Operating Characteristics, Package K
Channel A, BOP and BRP
Channel A, BOP and BRP
30
30
20
BOP
10
0
-40°C
25°C
150°C
BRP
-10
-20
-30
0
5
10
15
Switchpoint (G)
Switchpoint (G)
20
0
0
100
150
200
Channel B, BOP and BRP
30
20
BOP
10
0
-40°C
25°C
150°C
BRP
-10
Switchpoint (G)
20
Switchpoint (G)
50
Temperature (°C)
30
-20
0
5
10
15
0
3.3 V
12 V
18 V
BRP
-10
-20
-30
-50
20
BOP
10
0
50
100
150
200
Temperature (°C)
VCC (V)
Channels A and B, Hysteresis
Channels A and B, Hysteresis
30
30
25
25
20
-40°C
25°C
150°C
15
10
BOP - BRP (G)
BOP - BRP (G)
18 V
-20
Channel B, BOP and BRP
20
3.3 V
12 V
18 V
15
10
5
5
0
12 V
BRP
VCC (V)
-30
3.3 V
-10
-30
-50
20
BOP
10
0
5
10
15
VCC (V)
20
0
-50
0
50
100
150
200
Temperature (°C)
Additional magnetic characteristics on next page
16
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
Magnetic Operating Characteristics, Package K (continued)
BOP Symmetry
BOP Symmetry
30
30
20
10
-40°C
0
25°C
150°C
-10
-20
-30
0
5
10
15
Ch. A - Ch. B (G)
Ch. A - Ch. B (G)
20
12 V
0
18 V
-10
-20
-30
-50
20
3.3 V
10
0
VCC (V)
20
20
10
-40°C
0
25°C
150°C
-10
-20
10
15
VCC (V)
20
Ch. A - Ch. B (G)
Ch. A - Ch. B (G)
30
5
150
200
BRP Symmetry
BRP Symmetry
0
100
Temperature (°C)
30
-30
50
10
3.3 V
0
12 V
-10
18 V
-20
-30
-50
0
50
100
150
200
Temperature (°C)
Additional magnetic characteristics on next page
17
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
Magnetic Operating Characteristics, Package K (continued)
Channel A Symmetry
30
30
20
20
10
-40°C
0
25°C
150°C
-10
-20
BOP + BRP (G)
BOP + BRP (G)
Channel A Symmetry
-30
0
5
10
15
10
12 V
-10
18 V
-20
-30
-50
20
3.3 V
0
0
VCC (V)
30
30
20
20
10
-40°C
0
25°C
-10
150°C
-20
-30
5
10
VCC (V)
100
150
200
Channel B Symmetry
15
20
BOP + BRP (G)
BOP + BRP (G)
Channel B Symmetry
0
50
Temperature (°C)
10
3.3 V
0
12 V
-10
18 V
-20
-30
-50
0
50
100
150
200
Temperature (°C)
18
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
Package K, 4-pin SIP
+0.08
5.21 –0.05
45°
B
E
E
1.00
2.10
C
1.55 ±0.05
1.32 E
+0.08
3.43 –0.05
E1
E2
2.16
MAX
Mold Ejector
Pin Indent
Branded
Face
45°
1
D Standard Branding Reference View
N = Device part number
Y = Last two digits of year of manufacture
W = Week of manufacture
2
3
4
14.73 ±0.51
+0.06
0.38 –0.03
+0.07
0.41 –0.05
1
0.84 REF
A
0.51
REF
NNNN
YYWW
For Reference Only; not for tooling use (reference DWG-9010)
Dimensions in millimeters
Dimensions exclusive of mold flash, gate burrs, and dambar protrusions
Exact case and lead configuration at supplier discretion within limits shown
A
Dambar removal protrusion (8X)
B
Gate and tie bar burr area
C
Active Area Depth, 0.43 mm REF
D
Branding scale and appearance at supplier discretion
E
Hall elements (E1 and E2); not to scale
1.27 NOM
19
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
Package L, 8-pin SOIC
4.90 ±0.10
D
D
0.99
1.96
8
A
0.65
8°
0°
1.27
8
1.75
0.21 ±0.04
D
1.96
3.90 ±0.10 6.00 ±0.20
E1
E2
B
5.60
+0.43
0.84 –0.44
1.04 REF
1
2
0.25 BSC
8X
SEATING
PLANE
0.10 C
C
1
B
SEATING PLANE
GAUGE PLANE
+0.13
1.62 –0.27
0.41 ±0.10
1.27 BSC
+0.10
0.15 –0.05
NNNNNNN
YYWW
LLLL
For Reference Only; not for tooling use (reference DWG-9204)
Dimensions in millimeters
Dimensions exclusive of mold flash, gate burrs, and dambar protrusions
Exact case and lead configuration at supplier discretion within limits shown
A
2
PCB Layout Reference View
1
C
Active Area Depth, 0.40 mm REF
B Reference land pattern layout (reference IPC7351
SOIC127P600X175-8M); all pads a minimum of 0.20 mm from all
adjacent pads; adjust as necessary to meet application process
requirements and PCB layout tolerances
C Branding scale and appearance at supplier discretion
Standard Branding Reference View
N = Device part number
= Supplier emblem
Y = Last two digits of year of manufacture
W = Week of manufacture
L = Lot number
D Terminal #1 mark area
Copyright ©2005-2010, Allegro MicroSystems, Inc.
Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the
information being relied upon is current.
Allegro’s products are not to be used in life support devices or systems, if a failure of an Allegro product can reasonably be expected to cause the
failure of that life support device or system, or to affect the safety or effectiveness of that device or system.
The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use;
nor for any infringement of patents or other rights of third parties which may result from its use.
For the latest version of this document, visit our website:
www.allegromicro.com
20
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com