UDN2596 and UDN2597: 8-Channel Saturated Sink Drivers

Data Sheet
29320.2B
2596 AND
2597
8-CHANNEL
SATURATED SINK DRIVERS
Low output-saturation voltages at high load currents are provided
by UDN2596A and UDN2597A sink driver ICs. These devices can be
used as interface buffers between standard low-power digital logic
(particularly MOS) and high-power loads such as relays, solenoids,
stepping motors, and LED or incandescent displays. The eight saturated sink drivers in each device feature high-voltage, high-current
open-collector outputs. Transient suppression clamp diodes and a
minimum 35 V output sustaining voltage allow their use with many
inductive loads.
T
C
U
D
O
R
y
l
P On
The saturated (non-Darlington) NPN outputs provide low collectoremitter voltage drops as well as improved turn-off times due to an
active pull-down function within the output predrive section. The
UDN2596A is for use with output loads to 500 mA while the
UDN2597A is for use with loads to 1 A. Adjacent outputs may be
paralleled for higher load currents.
Inputs require very low input current and are activated by a low
logic level consistent with the much greater sinking capability associated with NMOS, CMOS, and TTL logic. The UDN2596A and
UDN2597A are rated for use with 5 V logic levels.
D
e
E
c
U
n
e
N er
I
T
f
e
N
R
O
r
C
o
S F
I
D
Dwg. No. W-100
Both devices are furnished in 20-pin DIP packages with copper
leadframes for improved thermal characteristics. The UDN2596A is
also available for operation between -40°C and +85°C. To order,
change the prefix from ‘UDN’ to ‘UDQ’.
FEATURES
ABSOLUTE MAXIMUM RATINGS
at TA = + 25°C
OutputVoltage,VCE ................................ 50 V
Output Current, IOUT
(UDN2596A) ............................ 500 mA
(UDN2597A) ................................ 1.0 A
Supply Voltage, VCC ............................ 7.0 V
Input Voltage, VlN ................................. 7.0 V
Package Power Dissipation,
PD ............................................. 2.27 W*
Operating Temperature Range,
TA ................................. -20°C to +85°C
Storage Temperature Range,
TS .............................. - 65°C to +150°C
■
■
■
■
■
Non-Inverting Function
Low Output ON Voltages
Up to 1.0 A Sink Capability
50 V Min. Output Breakdown
Output Transient-Suppression
Diodes
■ Output Pull-Down for
Fast Turn-Off
■ TTL, CMOS Compatible Inputs
■ Automotive Capable
ONE OF EIGHT DRIVERS
*Derate at the rate of 18.2 mW/°C above
TA = +25°C
Dwg. No. W-101
2596 AND 2597
8-CHANNEL
SATURATED SINK DRIVERS
ELECTRICAL CHARACTERISTICS at TA = +25°C, VCC = 5.0 V
Characteristics
Symbol
Output Leakage Current
ICEX
Output Sustaining Voltage
VCE(sus)
Output Saturation Voltage
VCE(SAT)
Applicable
Devices
Limits
Test Conditions
Min.
Max.
Units
Both
VOUT = 50 V, VIN = 2.4 V
—
10
µA
UDN2596A
lOUT = 300 mA, L = 2 mH
35
—
V
UDN2597A
lOUT = 750 mA, L = 2 mH
35
—
V
UDN2596A
lOUT = 300 mA
—
0.5
V
UDN2597A
lOUT = 750 mA
—
1.0
V
VR = 50 V
—
10
µA
Clamp Diode Leakage Current
IR
Both
Clamp Diode Forward Voltage
VF
UDN2596A
IF = 300 mA
—
1.8
V
UDN2597A
IF = 750 mA
—
1.8
V
UDN2956A
VIN = 0.8 V
—
-15
µA
UDN2597A
VIN = 0.8 V
—
-50
µA
Both
VIN = 2.4 V
—
10
µA
UDN2596A
any one driver VIN = 0.8 V
—
6.0
mA
UDN2597A
any one driver VIN = 0.8 V
—
31
mA
UDN2596A
all drivers VIN = 2.4 V
0.75
1.3
mA
UDN2597A
all drivers VIN = 2.4 V
0.75
15
mA
Logic lnput Current
IlN(0)
IlN(1)
Supply Current
ICC(ON)
ICC(OFF)
Turn-On Delay
tpd0
Both
0.5 EIN to 0.5 EOUT
—
3.0
µs
Turn-Off Delay
tpd1
Both
0.5 EIN to 0.5 EOUT
—
2.0
µs
TYPICAL APPLICATION
DUAL STEPPER MOTOR DRIVE
RECOMMENDED
OPERATING CONDITIONS
Type Number
Logic
IOUT
UDN2596A
5.0 V
300 mA
UDN2597A
5.0 V
750 mA
Note: Pins 2 and 12 must both be connected to
power ground.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
Copyright © 1984, 2003 Allegro MicroSystems, Inc.
2596 AND 2597
8-CHANNEL
SATURATED SINK DRIVERS
Dimensions in Inches
(controlling dimensions)
20
0.014
0.008
11
0.430
MAX
0.280
0.240
0.300
BSC
1
0.070
0.045
0.100
1.060
0.980
10
0.005
BSC
MIN
0.210
MAX
0.015
0.150
0.115
MIN
0.022
0.014
Dwg. MA-001-20 in
Dimensions in Millimeters
(for reference only)
20
0.355
0.204
11
10.92
MAX
7.11
6.10
7.62
BSC
1
1.77
1.15
2.54
26.92
24.89
10
BSC
0.13
MIN
5.33
MAX
0.39
3.81
2.93
MIN
0.558
0.356
NOTES: 1. Exact body and lead configuration at vendor’s option within limits shown.
2. Lead spacing tolerance is non-cumulative.
3. Lead thickness is measured at seating plane or below.
Dwg. MA-001-20 mm
2596 AND 2597
8-CHANNEL
SATURATED SINK DRIVERS
The products described here are manufactured under one or more
U.S. patents or U.S. patents pending.
Allegro MicroSystems, Inc. reserves the right to make, from time to
time, such departures from the detail specifications as may be
required to permit improvements in the performance, reliability, or
manufacturability of its products. Before placing an order, the user is
cautioned to verify that the information being relied upon is current.
Allegro products are not authorized for use as critical components
in life-support devices or systems without express written approval.
The information included herein is believed to be accurate and
reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringement of patents or other rights of
third parties which may result from its use.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000