WIDEST TEMPERATURE LOW POWER OSCILLATOR

PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
WIDEST TEMPERATURE LOW POWER OSCILLATOR
SERIES „WTLPO“
-55/+125°C
1.0—110.0 MHz
FEATURES
APPLICATIONS
+
+
+
+
+
+
+
+
+
+ Ruggedized equipment in harsh operating environment
+ Applications in extreme temperature conditions
100% pin-to-pin drop-in replacement to quartz and MEMS based XO
Highest Temperature Low Power Oscillator for Low Cost
Excellent long time reliability-outperforms quartz-based XO
Operating temperature from -55°C to 125°C
Supply voltage of 1.8V, 2.5V or 3.3V
Excellent total frequency stability as low as ±20 ppm
LVCMOS/LVTTL compatible output
Express samples within 1 day ex works PETERMANN-TECHNIK
Pb-free, RoHS and REACH compliant / MSL1@260°C
GENERAL DATA[1,2]
PARAMETER AND CONDITIONS
SYMBOL
MIN.
TYP.
MAX.
UNIT
CONDITION
f
1
–
110
MHz
F_stab
-20
–
+20
PPM
Inclusive of initial tolerance at 25°C, 1st year aging at 25°C,
-25
–
+25
PPM
and variations over operating temperature, rated power
-30
–
+30
PPM
supply voltage and load (15 pF ± 10%).
-50
–
+50
PPM
FREQUENCY RANGE
Output Frequency Range
FREQUENCY STABILITY AND AGING
Frequency Stability
OPERATING TEMPERATURE RANGE
Operating Temperature Range
T_use
-55
–
+125
°C
Widest temperature
Storage Temperature Range
T_stor
-55
–
+125
°C
Storage
VDD
1.62
1.8
1.98
V
2.25
2.5
2.75
V
2.52
2.8
3.08
V
SUPPLY VOLTAGE AND CURRENT CONSUMPTION
Supply Voltage
Current Consumption
OE Disable Current
Standby Current
IDD
I_OD
I_std
2.7
3.0
3.3
V
2.97
3.3
3.63
V
2.25
–
3.63
V
–
3.8
4.5
mA
No load condition, f = 20 MHz, VDD= 2.8V, 3.0V, or 3.3V
–
3.6
4.2
mA
No load condition, f = 20 MHz, VDD = 2.5V
–
3.4
4
mA
No load condition, f = 20 MHz, VDD = 1.8V
–
–
4.1
mA
VDD = 2.5V to 3.3V, OE = Low, output in high Z state
–
–
3.8
mA
VDD = 1.8V, OE = Low, output in high Z state
–
2.6
8.5
µA
VDD = 2.8V to 3.3V, ST = Low, output is pulled down
–
1.4
5.5
µA
VDD = 2.5V, ST = Low, output is pulled down
–
0.6
3.5
µA
VDD = 1.8V, ST = Low, output is pulled down
Note: 1. All electrical specifications in the above table are specified with 15 pF output load at default drive strength and for all VDD(s) unless otherwise stated.
2.The typical value of any parameter in the Electrical Characteristic table is specified for the nominal value of the highest voltage option for that parameter and at 25 °C
temperature.
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
PAGE 1 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014
PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
GENERAL DATA[1] (continued)
SYMBOL
MIN.
DC
45
–
55
%
All VDDs
Tr, Tf
–
1.0
2.0
ns
VDD = 2.5V, 2.8V, 3.0V or 3.3V, 20% - 80%
–
1.3
2.5
ns
VDD =1.8V, 20% - 80%
–
1.0
3.0
ns
VDD = 2.25V - 3.63V, 20% - 80%
VOH
90%
–
–
VDD
IOH = -4 mA (VDD = 3.0V or 3.3V)
IOH = -3 mA (VDD = 2.8V and VDD= 2.5V)
IOH = -2 mA (VDD= 1.8V)
VOL
–
–
10%
VDD
IOL = 4 mA (VDD = 3.0V or 3.3V)
IOL = 3 mA (VDD= 2.8V and VDD = 2.5V)
IOL = 2 mA (VDD = 1.8V)
Input High Voltage
VIH
70%
–
–
VDD
Pin 1, OE or ST
Input Low Voltage
VIL
–
–
30%
VDD
Pin 1, OE or ST
Input Pull-up Impedence
Z_in
50
87
150
kΩ
Pin 1, OE logic high or logic low, or ST logic high
2
–
–
MΩ
Pin 1, ST logic low
T_start
–
–
5
ms
Measured from the time VDD reaches 90% of final value
T_oe
–
–
130
ns
f = 110 MHz. For other frequencies, T_oe = 100 ns + 3* clock
periods
T_resume
–
–
5
ms
Measured from the time ST pin crosses 50% threshold
RMS Period Jitter
T_jitt
–
1.6
2.5
ps
f = 75 MHz, VDD = 2.5V, 2.8V, 3.0V or 3.3V
–
1.9
3
ps
f = 75 MHz, VDD = 1.8V
Peak-to-peak Period Jitter
T_pk
–
12
20
ps
f = 75 MHz, VDD = 2.5V, 2.8V, 3.0V or 3.3V
–
14
30
ps
f = 75 MHz, VDD = 1.8V
–
0.5
0.8
ps
f = 75 MHz, Integration bandwidth = 900 kHz to 7.5 MHz
–
1.3
2
ps
f = 75 MHz, Integration bandwidth = 12 kHz to 20 MHz
PARAMETER AND CONDITIONS
TYP.
MAX.
UNIT
CONDITION
LVCMOS OUTPUT CHARACTERISTICS
Duty Cycle
Rise/Fall Time
Output High Voltage
Output Low Voltage
INPUT CHARACTERISTICS
STARTUP AND RESUME TIMING
Startup Time
Enable/Disable Time
Resume Time
JITTER
RMS Phase Jitter (random)
T_phj
EXCELLENT RELIABILITY DATA
MTBF
500 million hours
Shock Resistance:
10.000 G
Note: 1. All electrical specifications in the above table are specified with 15 pF output load and for all V DD(s) unless otherwise stated.
Vibration Resistance:
70 g
PIN DESCRIPTION
PIN
1
SYMBOL
OE/ ST/NC
TOP VIEW
FUNCTIONALITY
Output Enable
H(3) : specified frequency output
L: output is high impedance. Only output driver is disabled.
Standby
H[3]: specified frequency output
L: output is low (weak pull down). Device goes to sleep mode.
Supply current reduces to I_std.
No connect
Any voltage between 0 and VDD or Open[3]: Specified frequency output. Pin 1 has no function.
2
GND
Power
Electrical ground[4]
3
OUT
Output
Oscillator output
4
VDD
Power
Power supply voltage[4]
1
4
VDD
GND 2
3
OUT
OE/ST/NC
Note: 3. In OE or ST mode, a pull-up resistor of 10kΩ or less is recommended if pin 1 is not externally driven. If pin 1 needs to be left floating, use the NC option.
4. A capacitor value of 0.1 µF between VDD and GND is required.
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
PAGE 2 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014
PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
TEST CIRCUIT AND WAVEFORM
FIGURE 1. TEST CIRCUIT
FIGURE 2. WAVEFORM
Vout
VDD
3
4
Power
Supply
Test
Point
tf
80%VDD
0.1µF
15pF
(including
probe
and fixture
capacitance)
2
1
tr
50%
20%VDD
High Pulse
(TH)
Low Pulse
(TL)
Period
VDD
OE/ST Function
1kΩ
TIMING DIAGRAMS
FIGURE 3. STARTUP TIMING (OE/ST MODE)
FIGURE 4. STANDBY RESUME TIMING (ST MODE ONLY)
VDD
90%VDD
Pin 4 Voltage
50%VDD
VDD
ST Voltage
T_resume
T_start
No Glitch during start up(5)
CLK Output
CLK Output
T_start: Time to start from power-off
FIGURE 5. OE ENABLE TIMING (OE MODE ONLY)
T_resume: Time to resume from ST
FIGURE 6. OE DISABLE TIMING (OE MODE ONLY)
VDD
50%VDD
VDD
OE Voltage
50%VDD
OE Voltage
T_oe
T_oe
CLK Output
CLK Output
T_OE: Time to re-enable the clock output
HZ
T_OE: Time to put the output drive in High Z mode
Note: 5. HTLPO has “no runt” pulses and “no glitch” output during startup or resume.
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
PAGE 3 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014
PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
PROGRAMMABLE DRIVE STRENGTH
The HTLPO includes a programmable drive strength feature named
SoftLevel to provide a simple, flexible tool to optimize the clock rise/
fall time for specific applications. Benefits from the programmable
drive strength feature are:
HIGH OUTPUT LOAD CAPABILITY
The rise/fall time of the input clock varies as a function of the actual
capacitive load the clock drives. At any given drive strength, the rise/
fall time becomes slower as the output load increases. As an examp-
+ Improves system radiated electromagnetic interference (EMI) by
le, for a 3.3V HTLPO device with default drive strength setting, the
typical rise/fall time is 1 ns for 15 pF output load. The typical rise/fall
slowing down the clock rise/fall time
+ Improves the downstream clock receiver’s (RX) jitter by decreasing (speeding up) the clock rise/fall time.
time slows down to 2.6 ns when the output load increases to 45 pF.
One can choose to speed up the rise/fall time to 1.83ns by then increasing the drive strength setting on the HTLPO.
+ Ability to drive large capacitive loads while maintaining full swing
with sharp edge rates.
The HTLPO can support up to 60 pF or higher in maximum capacitive
loads with drive strength settings. Refer to the Rise/Tall Time Tables
For more detailed information about rise/fall time control and drive
strength selection, please contacts the application engineers of Pe-
(Table 1 to 5) to determine the proper drive strength for the desired
combination of output load vs. rise/fall time.
termann-Technik.
EMI REDUCTION BY SLOWING RISE/FALL TIME (SoftLevel FUNCTION)
HTLPO DRIVE STRENGTH SELECTION
Figure 7 shows the harmonic power reduction as the rise/fall times
Tables 1 through 5 define the rise/fall time for a given capacitive load
are increased (slowed down). The rise/fall times are expressed as a
and supply voltage.
ratio of the clock period. For the ratio of 0.05, the signal is very close
to a square wave. For the ratio of 0.45, the rise/fall times are very
close to near-triangular waveform. These results, for example, show
that the 11th clock harmonic can be reduced by 35 dB if the rise/fall
edge is increased from 5% of the period to 45% of the period.
Select the table that matches the HTLPO nominal supply
voltage (1.8V, 2.5V, 2.8V, 3.0V, 3.3V).
2.
Select the capacitive load column that matches the application requirement (5 pF to 60 pF)
3.
Under the capacitive load column, select the desired
rise/fall times.
FIGURE 7. HARMONIC EMI REDUCTION AS A FUNCTION OF
SLOWER RISE/FALL TIME (SoftLevel FUNCTION)
4.
The left-most column represents the part number code for
the corresponding drive strength.
10
Harmonic amplitude (dB)
1.
5.
0
Add the drive strength code to the part number for
ordering purposes.
-10
-20
CALCULATING MAXIMUM FREQUENCY
-30
Based on the rise and fall time data given in Tables 1 through 5, the
-40
maximum frequency the oscillator can operate with guaranteed
-50
full swing of the output voltage over temperature as follows:
-60
Max. frequency =
-70
-80
1
3
trise=0.05
5
7
9
Harmonic number
trise=0.1
trise=3
trise=0.15
trise=0.35
trise=0.2
trise=0.4
11
trise=0.25
trise=0.45
JITTER REDUCTION WITH FASTER RISE/FALL TIME
Power supply noise can be a source of jitter for the downstream chipset. One way to reduce this jitter is to increase rise/fall time (edge
rate) of the input clock. Some chipsets would require faster rise/fall
1
5 x Trf_20/80
where Trf_20/80 is the typical value for 20%-80% rise/fall time.
EXAMPLE 1
Calculate fMAX for the following condition:
+ VDD = 1.8V (Table 1)
+ Capacitive Load: 30pF
+ Desired Tr/f time = 3 ns (rise/fall time part number code=E)
Part number for the above example:
time in order to reduce their sensitivity to this type of jitter. The HTLPO provides up to 3 additional high drive strength settings for very
HTLPO18-2520-E-25-WT-75.000MHz-T-S
fast rise/fall time. Refer to the Rise/Fall Time Tables to determine
the proper drive strength.
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
Drive strength code is inserted here. Standard setting is “S”
PAGE 4 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014
PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
RISE/FALL TIME (20% TO 80%) vs CLOAD
TABLE 1. VDD = 1.8V RISE/FALL TIMES FOR SPECIFIC CLOAD
TABLE 2. VDD = 2.5V RISE/FALL TIMES FOR SPECIFIC CLOAD
RISE/FALL TIME TYP (NS)
Drive Strength \ CLOAD
RISE/FALL TIME TYP (NS)
5 pF
15 pF
30 pF
45 pF
60 pF
L
6.16
11.61
22.00
31.27
39.91
Drive Strength \ CLOAD
5 pF
15 pF
30 pF
45 pF
60 pF
L
4.13
8.25
12.82
21.45
27.79
A
3.19
6.35
11.00
16.01
21.52
A
2.11
4.27
7.64
11.20
14.49
R
2.11
4.31
7.65
10.77
14.47
R
1.45
2.81
5.16
7.65
9.88
B
1.65
3.23
5.79
8.18
11.08
B
1.09
2.20
3.88
5.86
7.57
T
0.93
1.91
3.32
4.66
6.48
T
0.62
1.28
2.27
3.51
4.45
E
0.78
1.66
2.94
4.09
5.74
S for standard
0.54
1.00
2.01
3.10
4.01
U
0.70
1.48
2.64
3.68
5.09
U
0.43
0.96
1.81
2.79
3.65
S for standard
0.65
1.30
2.40
3.35
4.56
F
0.34
0.88
1.64
2.54
3.32
TABLE 3. VDD = 2.8V RISE/FALL TIMES FOR SPECIFIC CLOAD
TABLE 4. VDD = 3.0V RISE/FALL TIMES FOR SPECIFIC CLOAD
RISE/FALL TIME TYP (NS)
Drive Strength \ CLOAD
5 pF
15 pF
L
3.77
7.54
30 pF
RISE/FALL TIME TYP (NS)
45 pF
60 pF
12.28
19.57
25.27
Drive Strength \ CLOAD
5 pF
15 pF
30 pF
45 pF
60 pF
L
3.60
7.21
11.97
18.74
24.30
A
1.94
3.90
7.03
10.24
13.34
A
1.84
3.71
6.72
9.86
12.68
R
1.29
2.57
4.72
7.01
9.06
R
1.22
2.46
4.54
6.76
8.62
B
0.97
2.00
3.54
5.43
6.93
B
0.89
1.92
3.39
5.20
6.64
T
0.55
1.12
2.08
3.22
4.08
S for standard
0.51
1.00
1.97
3.07
3.90
S for standard
0.44
1.00
1.83
2.82
3.67
E
0.38
0.92
1.72
2.71
3.51
U
0.34
0.88
1.64
2.52
3.30
U
0.30
0.83
1.55
2.40
3.13
F
0.29
0.81
1.48
2.29
2.99
F
0.27
0.76
1.39
2.16
2.85
TABLE 5. VDD = 3.3V RISE/FALL TIMES FOR SPECIFIC CLOAD
RISE/FALL TIME TYP (NS)
Drive Strength \ CLOAD
5 pF
15 pF
30 pF
45 pF
L
3.39
6.88
11.63
17.56
60 pF
23.59
A
1.74
3.50
6.38
8.98
12.19
R
1.16
2.33
4.29
6.04
8.34
B
S
for
standard
T or "-": standard
0.81
0.46
0.46
1.82
1.00
1.00
3.22
1.86
1.86
4.52
2.60
2.60
6.33
3.84
3.84
E
E
U
U
F
F
0.33
0.33
0.28
0.28
0.87
0.87
0.79
0.79
1.64
1.64
1.46
1.46
2.30
2.30
2.05
2.05
3.35
3.35
2.93
2.93
0.25
0.25
0.72
0.72
1.31
1.31
1.83
1.83
2.61
2.61
Note: 6. “n/a” in Table 1 to Table 5 indicates that the resulting rise/fall time from the respective combination of the drive strength and output load does not provide rail-torail swing and is not available.
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
PAGE 5 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014
PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
PROGRAMMABLE DRIVE STRENGTH
PIN 1 CONFIGURATION OPTIONS (OE, ST, OR NC)
FIGURE 8. STARTUP WAVEFORM vs. VDD
Pin 1 of the HTLPO can be factory-programmed to support three
modes: Output enable (OE), standby (ST) or No Connect (NC).
OUTPUT ENABLE (OE) MODE
In the OE mode, applying logic Low to the OE pin only disables the
output driver and puts it in Hi-Z mode. The core of the device
continues to operate normally. Power consumption is reduced due
to the inactivity of the output. When the OE pin is pulled High, the
output is typically enabled in <1µs.
STANDBY (ST) MODE
In the ST mode, a device enters into the standby mode when Pin 1
pulled Low. All internal circuits of the device are turned off. The
current is reduced to a standby current, typically in the range of a
FIGURE 9. STARTUP WAVEFORM vs. VDD (ZOOMED-IN VIEW OF
FIGURE 8)
few µA. When ST is pulled High, the device goes through the
“resume” process, which can take up to 5 ms.
NO CONNECT (NC) MODE
In the NC mode, the device always operates in its normal mode
and output the specified frequency regardless of the logic level on
pin 1. Table 6 below summarizes the key relevant parameters in the
operation of the device in OE, ST, or NC mode.
TABLE 6. OE vs. ST vs. NC
OE
ST
NC
Active current 125 MHz (max,
1.8V)
4 mA
4 mA
4 mA
OE disable current (max. 1.8V)
3.8 mA
N/A
N/A
Standby current (typical 1.8V)
N/A
0.6 uA
N/A
OE enable time at 125 MHz
(max)
130 ns
N/A
N/A
Resume time from standby
(max, all frequency)
N/A
5 ms
N/A
Output driver in OE disable/
standby mode
High Z
Weak pulldown
N/A
OUTPUT ON STARTUP AND RESUME
The HTLPO comes with gated output. Its clock output is accurate
to the rated frequency stability within the first pulse from initial
device startup or resume from the standby mode.
In addition, the HTLPO has NO RUNT, NO GLITCH output during
startup or resume as shown in the waveform captures in Figure 8
and Figure 9.
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
PAGE 6 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014
PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
DIMENSIONS AND PATTERNS
RECOMMENDED LAND PATTERN (UNIT:MM) [7]
PACKAGE SIZE – DIMENSIONS (UNIT:MM)
2.0 X 1.6 X 0.75 MM
#1
1.5
0.65
#3
#3
#1
#2
#2
0.8
1.2
0.93
#4
0.48
2.0±0.05
1.6±0.05
#4
0.9
0.75±0.05
0.68
RECOMMENDED LAND PATTERN (UNIT:MM)
PACKAGE SIZE – DIMENSIONS (UNIT:MM)
2.5 X 2.0 X 0.75 MM
#1
1.9
1.00
#3
#3
#1
#2
#2
1.0
1.1
1.5
#4
0.5
2.5±0.05
2.0±0.05
#4
1.1
0.75±0.05
0.75
RECOMMENDED LAND PATTERN (UNIT:MM)
PACKAGE SIZE – DIMENSIONS (UNIT:MM)
3.2 X 2.5 X 0.75 MM
#3
#1
#2
#2
1.2
0.9
1.9
#4
0.9
1.4
0.75±0.05
#1
2.2
2.1
#3
0.7
3.2±0.05
2.5±0.05
#4
Note: 7. A capacitor value of 0.1 µF between VDD and GND is recommended.
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
PAGE 7 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014
PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
DIMENSIONS AND PATTERNS
RECOMMENDED LAND PATTERN (UNIT:MM) [8]
PACKAGE SIZE – DIMENSIONS (UNIT:MM)
5.0 X 3.2 X 0.75 MM
#1
2.54
2.39
#3
#3
#1
#2
#2
1.6
0.8
2.2
#4
1.1
5.0±0.05
3.2±0.05
#4
1.5
0.75±0.05
1.15
RECOMMENDED LAND PATTERN (UNIT:MM)
PACKAGE SIZE – DIMENSIONS (UNIT:MM)
7.0 X 5.0 X 0.90 MM
#3
#1
#2
3.81
#4
#2
2.0
1.1
1.4
2.2
0.90±0.10
#1
5.08
5.08
#3
2.6
7.0±0.05
5.0±0.05
#4
REFLOW SOLDER PROFILE
Note: 8. A capacitor value of 0.1 µF between VDD and GND is recommended.
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
PAGE 8 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014
PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
ORDERING INFORMATION
OSCILLATOR
FAMILY
SUPPLY VOLTAGE
“18“ for 1.8V
“25“ for 2.5V
“28“ for 2.8V
“3“ for 3.0V
“33“ for 3.3V
“XX“ for 2.25V to 3.63V
WTLPO
TEMPERATURE
RANGE
FREQUENCY
1.000000 to
110.000000 MHz
“WT” for –55 +125°C
WTLPO 33-2520-E-25-WT-25.000MHz-T-S
FREQUENCY
STABILITY
“20” for ±20 PPM
“25” for ±25 PPM
“30” for ±30 PPM
“50” for ±50 PPM
PACKING METHOD
“B” Buls or Tubes
“T” Tape & Reel
FEATURE PIN 1
PACKAGE SIZE
“2016” for 2.0 X 1.6 mm
“2520” for 2.5 X 2.0 mm
“3225” for 3.2 X 2.5 mm
“5032” for 5.0 X 3.2 mm
“7050” for 7.0 X 5.0 mm
OUTPUT DRIVE
STRENGTH
“E” for OUTPUT ENABLE
“S” for STANDBY
“N” for NO CONNECT
“S” Standard (datasheet
limits) See Tables 1 to 5
for rise/fall times
“L”
“T”
“A”
“E”
“R”
“U”
“B”
“F”
EXAMPLE: WTLPO33-2520-E-25-WT-25.000MHz-T-S
PLEASE INDICATE YOUR REQUIRED PARAMETERS
EXPRESS SAMPLES ARE DELIVERABLE ON THE SAME DAY
IF ORDERED UNTIL 02:00 PM!
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
PAGE 9 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014
PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
PREMIUM QUALITY BY
PETERMANN-TECHNIK
OUR COMPANY IS CERTIFIED ACCORDING TO ISO 9001:2008 IN OCTOBER 2013 BY THE DMSZ CERTIFIKATION GMBH.
THIS IS FOR YOU TO ENSURE THAT THE PRINCIPLES OF QUALITY
MANAGEMENT ARE FULLY IMPLEMENTED IN OUR QUALITY MANAGEMENT SYSTEM AND QUALITY CONTROL METHODS ALSO DOMINATE OUR QUALITY STANDARDS.
© PETERMANN-TECHNIK GmbH 2014. The information contained herein is subject to change at any time without notice. PETERMANN-TECHNIK owns
all rights, title and interest to the intellectual property related to PETERMANN-TECHNIK's products, including any software, firmware, copyright, patent, or trademark. The sale of PETERMANN-TECHNIK products does not convey or imply any license under patent or other rights. PETERMANNTECHNIK retains the copyright and trademark rights in all documents, catalogs and plans supplied pursuant to or ancillary to the sale of products or
services by PETERMANN-TECHNIK. Unless otherwise agreed to in writing by PETERMANN-TECHNIK, any reproduction, modification, translation, compilation, or representation of this material shall be strictly prohibited.
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
PAGE 10 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014