!LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only LED SMD Pb Lead-Free Parts LG-170DBK-CT-SD DATA SHEET DOC. NO : QW0905-LG-170DBK-CT-SD REV. : B DATE : 06 - Sep. - 2012 發行 立碁電子 DCC !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 1/11 PART NO. LG-170DBK-CT-SD Features: 1. Package in 8.0mm carrier tape on 7" diameter reel. 2. Compatible with automatic placement equipment. 3. Compatible with reflow solder process. Descriptions: 1. The LG-170 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. 2. Besides, lightweight makes them ideal for miniature applications. etc. Applications: 1. Automotive : backlighting in dashboard and switch. 2. Telecommunication : indicator and backlighting in telephone and fax. 3. Flat backlight for LCD, switch and symbol 4. General use. Device Selection Guide: PART NO MATERIAL LG-170DBK-CT-SD lnGaN COLOR Emitted Lens Blue Water Clear !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 2/11 PART NO. LG-170DBK-CT-SD Package Dimensions 0.8 Cathode Mark 0.3 1.25 Cathode Mark Resin 0.4 LED DICE 2.0 Soldering Terminal 1.4 Polarity 0.4 Note : 1.All dimension are in millimeter tolerance is ̈́0.1mm unless otherwise noted. 2.Specifications are subject to change without notice. Recommended Soldering Pad Dimensions 1.2 1.2 0.9 1.2 Note : The tolerances unless mentioned is ̈́0.1mm,Angle ̈́0.5. Unit=mm. !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 3/11 PART NO. LG-170DBK-CT-SD Absolute Maximum Ratings at Ta=25к Symbol Ratings UNIT Power Dissipation PD 80 mW Peak Forward Current Duty 1/10@10KHz IFP 100 mA Forward Current IF 20 mA Reverse Current @5V Ir 50 ȝA Electrostatic Discharge ESD 500 V Operating Temperature Topr -20 ~ +80 к Storage Temperature Tstg -30 ~ +100 к Parameter Typical Electrical & Optical Characteristics (Ta=25к) Items Symbol Min. Typ. Max. UNIT CONDITION Luminous Intensity Iv 62 90 ---- mcd IF=20mA Dominant Wavelength ȜD ---- 470 ---- nm IF=20mA Ϧӳ ---- 30 ---- nm IF=20mA VF 2.8 ---- 3.6 V IF=20mA 2ș 1/2 ---- 140 ---- deg IF=20mA Spectral Line Half-Width Forward Voltage Viewing Angle Note : 1.The forward voltage data did not including ̈́0.1V testing tolerance. 2. The luminous intensity data did not including ̈́15% testing tolerance. !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 4/11 PART NO. LG-170DBK-CT-SD Luminous Intensity Classification BIN CODE D21 D22 D23 D24 D25 Iv(mcd) at 20mA Min. Max. 62 75 90 108 130 75 90 108 130 156 Dominant Wavelength Classification BIN CODE S10 S11 S12 S13 ȜD(nm) at 20mA Min. Max. 468 470 472 474 470 472 474 476 !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 5/11 PART NO. LG-170DBK-CT-SD Typical Electro-Optical Characteristics Curve DBK CHIP Fig.2 Relative Intensity vs. Forward Current 3.0 1000 Relative Intensity Normalize @20mA Forward Current(mA) Fig.1 Forward current vs. Forward Voltage 100 10 1 01 2.5 2.0 1.5 1.0 0.5 0.0 1.0 2.0 3.0 4.0 5.0 1 10 1.2 1.1 1.0 0.9 0.8 0 20 40 60 80 100 Fig.5 Relative Intensity vs. Wavelength 1.0 0.5 0.0 400 450 500 Wavelength (nm) 3.0 2.5 2.0 1.5 1.0 0.5 0.0 -40 -20 0 20 40 60 80 Ambient Temperature( к) Ambient Temperature( к) Relative Intensity@20mA Fig.4 Relative Intensity vs. Temperature Relative Intensity@20mA Normalize @25к Forward Voltage@20mA Normalize @25к Fig.3 Forward Voltage vs. Temperature -20 1000 Forward Current(mA) Forward Voltage(V) -40 100 550 Fig.6 Directive Radiation 100 !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 6/11 PART NO. LG-170DBK-CT-SD Carrier Type Dimensions 2.0 1.5 4.0̈́0.2 0.25 1.75 3.5̈́0.2 8.0̈́0.3 5.3 2.22 Polarity 0.87 4.0±0.2 1.36 Note : The tolerances unless mentioned is ̈́0.1mm,Angle ̈́ʳ0.5. Unit=mm. Θ Packing Specifications Label Aluminum Moist-Proof bag Label Part No. Description Quantity/Reel LG-170DBK-CT-SD 8.0mm tape,7"reel 4000 devices !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 7/11 PART NO. LG-170DBK-CT-SD Label Explanation LIGITEK ELECTRONICS CO., LTD. Pb !QBSU!; ! MH.281ECL.DU.TE BIN : Radiant Intensity !MPU!; ! HT2.191279 HUE : Peak Emission Wavelength !RUZ)QDT*;! 5111 !CJO0IVF!;! E320T23 ! WG;2/9.3/1 VF : Forward Voltage Reel Dimensions 0.2 0.4 0.8 0.8 0.6 0.2 0.4 0.6 2.0̈́0.5 178̈́1.5 6.0̈́1.0 9.0̈́1.0 ӿ13.5̈́1.0 12.0̈́1.0 !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 8/11 PART NO. LG-170DBK-CT-SD Box Explanation 1. 5 BAG / INNER BOX 2. INNER BOX SIZE : L X W X H 23cm X 8.5cm x 26cm H W L 3. 10 INNER BOXES / CARTON 4. CARTON SIZE : L X W X H 58cm X 34cm x 35cm L W H !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LG-170DBK-CT-SD Page 9/11 Recommended Soldering Conditions 1. Hand Solder Basic spec is Љ 280к 3 sec one time only. 2. Wave Solder Soldering heat Max. 260 к 245̈́5кʳwithin 5 sec 120 ~ 150к Preheat 120 ~ 180 sec 3 PB-Free Reflow Solder 1~5°C/sec Preheat 180~200°C 1~5°C/sec 260°C MaX. 10sec.Max 6°C/sec Above 220°C 60 sec.Max. 120 sec.Max. Note: 1.Reflow soldering should not be done more than two times. 2.When soldering,do not put stress on the LEDs during heating. 3.After soldering,do not warp the circuit board. !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 10/11 PART NO. LG-170DBK-CT-SD Precautions For Use: Storage time: 1.The operation of Temperatures and RH are : 5 к~35к,RH60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year at І30к and І90% relative humidity(RH) (from production date). 3.If opened more than one week in an atmosphere 5 к ~ 35к,RH60%, they should be treated at 60 к±5 кfo r 15hrs. Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forward current should not be allowed to change by more than 40% of its desired value. Circuit model A Circuit model B LED LED (A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 11/11 PART NO. LG-170DBK-CT-SD Reliability Test: Classification Test Item Test Condition Reference Standard Operating Life Test 1.Ta=Under Room Temperature As Per Data Sheet Maximum Rating. 2.If=50mA 3.t=1000 hrs (-24hrs, +72hrs) MIL-STD-750D: 1026 MIL-STD-883D: 1005 JIS C 7021: B-1 High Temperature Storage Test 1.Ta=105 к²5к 2.t=1000 hrs (-24hrs, +72hrs) MIL-STD-883D:1008 JIS C 7021: B-10 Low Temperature Storage Test 1.Ta=-40 к²5к 2.t=1000 hrs (-24hrs, +72hrs) JIS C 7021: B-12 High Temperature High Humidity Storage Test 1.Ta=65 к²5к 2.RH=90%~95% 3.t=1000hrs¡Ó2hrs Endurance Test Thermal Shock Test Solderability Test Environmental Test Temperature Cycling IR Reflow 1.Ta=105 к̈́ˈк&-40к̈́5к (10min) (10min) 2.total 10 cycles 1.T.Sol=235 к̈́5к 2.Immersion time 2 ̈́0.5sec 3.Coverage Њ95% of the dipped surface 1.105кʳ̑ʳ25кʳ̑ʳˀ55кʳ̑ʳ25к 30mins 5mins 30mins 5mins 2.10 Cyeles 1.T=260°C Max. 10sec.Max. 2. 6 Min MIL-STD-202F:103B JIS C 7021: B-11 MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1011 MIL-STD-202F: 208D MIL-STD-750D: 2026 MIL-STD-883D: 2003 IEC 68 Part 2-20 JIS C 7021: A-2 MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1010 JIS C 7021: A-4 MIL-STD-750D:2031.2 J-STD-020