LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only 0.4W Power Light LED Pb Lead-Free Parts LG-5630WKZ-DT-1-P-A04 DATA SHEET DOC. NO : QW0905-LG-5630WKZ-DT-1-P-A04 REV. : E DATE : 13 - Apr. - 2012 發行 立碁電子 DCC LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Product Model Designation System LG - 56 30 WK Z - D T - P - X - A04 X1 X2 X1 Title X3 X4 X2 Dimension(L) LG:Ligitek X6 Epoxy Color D:Yellow Diffused 57:5.7mm 56:5.6mm X5 X3 30:3.0mm X8 Package Patent X8 X4 Dimension(W) X7 T:Tape&Reel X6 X7 Emitting Color X9 X5 Zener WK:White Color X9 Chip Modification P:IP free X10 -X: 2 chip in 1(Parallel) -1: 1 chip in 1 -2: 2 chip in 1(Series) Page 1/15 X10 Bin Modification LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Typical Applications Features *. White colored SMTpackage *.Suitable for all SMT assembly and soldering methodes *. Pb-Free Reflow soldering application *. More Energy Efficient than lncandescent and most Halogen lamps. *. RoHS compliant *. Reading Light (car,bus,aircraft) *. Portable(flashlight,bicycle). *. Backlights(Monitor,TV) / Light Guides. *. Automotive Exterior (Stop-Tail-Tum,CHMSL,Mirror Side Repeat). *. Commercial and Residential Architectural lighting. *. Mini-accent / Uplighters / Downlighters / Orientation lighting *. Fiber Optic Alternative / Decorative / Entertainment lighting. *. Security / Garden lighting. *. Cove / Undershelf / Task lighting. *. Traffic signaling / Beacons / Rail crossing and Wayside lighting. Dimension 5.3 C 3.0 A C Recommended Solder Patterns 5.6 2.0 0.9 1.6 1.62 3.8 6.8 0.5 0.8 1.28 0.5 2.1 Slug Anode(+) 0.3 2.3 0.8 Cathode(-) Note: 1.The tolerance unless mentioned is ±0.1mm,unit=mm. 2.The slug has polarity as anode. 3.It is strongly recommended to apply on electrically isolated heat conducting film between the slug and contact surfaces. Page 2/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Absolute Maximum Ratings at Ta=25℃ Ratings Parameter Symbol UNIT White DC Forward Current IF 150 mA Power Dissipation PD 0.6 W Peak pulse current Duty 1/10@10KHz IFP 200 mA LED junction Temperature Tj 125 ℃ Reverse Current(VR=5V) Ir 10 µA ESD Sensitivity VB ±2000 V Storage Temperature Tstg -40 ~ +100 ℃ Operating Temperature Topr -40 ~ +85 ℃ Soldering Temperature Tp 260 ℃ Hand Soldering Time at320°C(Max) Tsol 3 seconds Note: 1.Proper current derating must be observed to maintain temperature below the maximum. 2.LEDS are not designed to be driven in reverse bias. Luminous Intensity Characteristics at 120mA (Ratings At 25°C Ambient) PART NO Luminous Intensity @120mA Emission Color Min. LG-5630WKZ-DT-1-P-A04 White Typ. 12500 13200 Max. ---- Note : 1. White emitters are built with InGaN. 2. Luminous Intensity is measured with an accuracy of ±10% Page 3/15 Units mcd LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Forward Voltage Characteristics at 120mA (Ratings At 25°C Ambient) Vf PART NO Emission Color Min. Typ. Max. LG-5630WKZ-DT-1-P-A04 White ---- 3.3 3.6 Units V Note : Forward Voltage is measured with an accuracy of±0.1V Chromaticity Coordinates Characteristics at 120mA (Ratings At 25°C Ambient ) PART NO Emission Color LG-5630WKZ-DT-1-P-A04 White Chromaticity Coordinates X Y Max. Max. Min. Min. 0.2447 0.2615 0.2103 0.2318 Note : ±0.01 is tester tolerance. Emission Angle Characteristics at 120mA (Ratings At 25°C Ambient ) PART NO Emission Color Lambertian Units LG-5630WKZ-DT-1-P-A04 White 120 Degrees Page 4/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Bin Code Description Bin Code Luminous Intensity K00K50 CIE Forward Voltage B1 3.05-3.2 Luminous Intensity (mcd) @IF=120mA 正面噴碼 Bin Code Min. Max. 8 J50K00 12500 13000 9 K00K50 13000 13500 A K50L00 13500 14000 B L00L50 14000 14500 C L50M00 14500 15000 D M00M50 15000 15500 E M50N00 16000 15500 Forward Voltage(V) @IF=120mA Color Rank @IF=120mA A1-D1 Page 5/15 Bin Code Range 正面噴碼 V1 2.9-3.05 1 V2 3.05-3.2 2 V3 3.2-3.35 3 V4 3.35-3.5 4 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Bins Code of chromaticity coordinates 1 CODE A1 B1 C1 D1 X 0.2567 0.2537 0.2507 0.2477 2 Y 0.2482 0.2398 0.2314 0.2230 X 0.2645 0.2615 0.2585 0.2555 3 Y 0.2439 0.2355 0.2271 0.2187 NOTE: Tolerance on each color bin(x,y)is±0.01 Page 6/15 X 0.2615 0.2585 0.2555 0.2525 4 Y 0.2355 0.2271 0.2187 0.2103 X 0.2537 0.2507 0.2477 0.2447 Y 0.2398 0.2314 0.2230 0.2146 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only The C.I.E 1931 Chromaticity Coordinates 0.26 G1L 0.25 A1L★ A1 0.24 B1L B1 0.23 C1L★ C1 0.22 D1L D1 0.21 0.20 0.19 0.18 0.22 0.23 0.24 0.25 0.26 Page 7/15 0.27 0.28 0.29 0.30 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Recommended Profile for Reflow Soldering Pb -free solder temperature profile Pb -free solder Temperature profile Pre-heat Pre-heat time Peak-Temperature Soldering time condition 180-200°C 120 Sec Max 260°C Max 10 Sec Max 260°C.Max. 10 Sec .Max. 1-5°C/Sec. 60 Sec.Max. Above220°C 6°C/Sec. Pre-heating 180-200°C 1-5°C/Sec. 120 Sec. Max. (1) Reflow soldering should not be done more than two times. (2) When soldering,do not put stress on the LEDs during heating. (3) After soldering,do not warp the circuit board. (4) The encapsulated material of the LEDs is silicone. Precautions should be taken to avoid the strong pressure on the encapsulated part. So when using the chip mounter,the picking up nozzle that does not affect the silicone resin should be used. Hand Soldering Conditions: Do not exceed 3 seconds at maximum 320°C under soldering iron.(one time only) Page 8/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Fig.1 Forward current vs. Forward Voltage Forward Current(mA) 160 120 80 40 0 2.0 2.5 3.0 3.5 4.0 4.5 Forward Voltage(V) Fig.2 Forward current vs.Luminous Intensity Relative Luminous Intensity(%) 1.2 1.0 0.8 0.6 0.4 0.2 0 30 60 Page 9/15 90 120 150 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Relative Luminous Flux(%) Fig.3 Luminous Spectrum(Ta=25 ℃) SPECTRAL RADIANCE 100 80 60 40 20 0 400 500 600 700 800 Wavelength (nm) Fig.4 Directivity Radiation 0° -30° 30° -60° 100% 75% 50% 60° 25% 0 Page 10/15 25% 50% 75% 100% LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Carrier Type Dimensions 4.0 0.25 1.5 1.75 - 5.5 + 12.0±0.3 5.95 9.3 Polarity 4.0 3.25 1.2 Note : The tolerances unless mentioned is ±0.2mm. Packing Specifications Label Aluminum Moist-Proof bag Label Desiccant Page 11/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Label Explanation Pb LIGITEK ELECTRONICS CO., LTD. PART : LG-5630WKZ-DT-1-P-A04 BIN : Luminous Flux LOT : GS1-060109 QTY(PCS): 2000 HUE : Chromaticity Coordinates (CIE_x , CIE_y) BIN/HUE : J50K00/C1 VF:3.0-3.2 3.0 - 3.2 : Forward Voltage Reel Dimensions 16.0± 1.0 60.2±0.5 Page 12/15 178±1 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Box Explanation 1. 4 BAG / INNER BOX 2. INNER BOX SIZE : L X W X H 23cm X 8.5cm x 26cm H W L 3. 10 INNER BOXES / CARTON 4. CARTON SIZE : L X W X H 58cm X 34cm x 35cm W L H Page 13/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Reliability Test (1)Test items and results Classification Test Item Test Condition Sample Size Operating Life Test 1.Ta=Under Room Temperature As Per Data Sheet Maximum Rating. 2.If= 120mA 3.t=1000 hrs 22 High Temperature Storage Test 1.Ta=100 ℃ 2.t= 1000 hrs 22 Low Temperature Storage Test 1.Ta=-40 ℃ 2.t=1000 hrs 22 High Temperature High Humidity Storage Test 1.Ta= 85℃ 2.RH=85 % 3.t= 1000 hrs 22 Endurance Test Thermal Shock Test Environmental Test Reflow Soldering Test Temperature Cycling 1.Ta=-40 ℃(30min) -100 ℃( 30min) 2.total 100 cycles 22 1.T.Sol=260 ℃±5 ℃ 2.Dwell Time= 10 Sec.Max. 22 1.100 ℃ ~ 25 ℃ ~ - 40 ℃ 30mins 5mins 30mins 2.10 0 Cyeles 22 (2)Criteria for judging the damage Criteria for Judgement Item Symbol Test Conditions Min. Max. Forward Voltage Vf If=120mA - U.S.L x1.2 Reverse Current Ir Vr=5V - U.S.L x2.0 Luminous Intensity Iv If=120mA L.S.L x 0.5 - Note: 1.U.S.L.:Upper Standard Level. 2.L.S.L.:Lower Standard Level. Page 14/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Precautions For Use: Storage time: 1.The operation of Temperatures and RH are : 5 ℃~35℃,RH60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year(from production date). 3.If opened more than one week in an atmosphere 5 ℃ ~ 35℃,RH60%, they should be treated at 60 ℃±5 ℃for 15hrs. Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forward current should not be allowed to change by more than 40% of its desired value. Circuit model A Circuit model B LED LED (A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. Page 15/15