Link zum Datenblatt der Type FYLS-0603AUGC

Model. No.
Rev.
FYLS-0603AUGC
A
PRODUCT SPECIFICATION
Model No.
:FYLS-0603AUGC
Features:
■SMD Type
■Size (mm):1.6*0.8*0.4
■Emitting Color:Yellow Green
■SMT package
■Suitable for all SMT assembly and soldering method
■Pb-free Reflow soldering application
■RoHS Compliant
■Light Strips
■LCD Backlight
■Decorative lighting
■Indicators
■Interior automotive
■Illuminations
■Mobile Phones
CUSTOMER APPROVED
SIGNATURES
Applications:
APPROVED BY
NINGBO FORYARD OPTOELECTRONICS CO.,LTD
Add:NO.115 Qixin Road Ningbo Zhejiang China
Tel: 0086-574-87933652 87927870 87922206
Fax: 0086-574-87927917
E-mail:[email protected] ( General)
Http://www.foryard.com
CHECKED BY
PREPARED BY
Zip:315051
Http://www.foryard.com
Page
:
1/8
Model. No.
Rev.
Model No.
FYLS-0603AUGC
A
:FYLS-0603AUGC
■ Mechanical Dimensions
Notes:
1. Dimension in millimeter [inch], tolerance is ±0.25 [.010].
2.The specifications,characteristics and technical data described in the datasheet are subject to change without prior notice.
Http://www.foryard.com
Page
:
2/8
FYLS-0603AUGC
A
Model. No.
Rev.
Model No.
:FYLS-0603AUGC
■ Absolute Maximun Ratings(Ta=25ºC)
Items
Symbol
Absolute maximum Rating
Unit
IF
30
mA
Peak Forward Current*
IFP
100
mA
Power Dissipation
PD
78
Mw
Forward Current(DC)
Operation Temperature
Topr
Storage Temperature
Tstg
Reverse Voltage
VR
Soldering Temperature
Tsol
º~ º
-40ºC~+100ºC
℃
℃
-30 C +80 C
5
Reflow Soldering:250
≦1msec duty≦1/10
℃/5sec
V
*Pulse width
■ Typical Electrical &Optical Charcteristics(Ta=25ºC)
Items
Symbol
Condition
Forward Voltage
VF
IF = 20mA
Reverse Current
IR
VR = 5V
Peak Emission Wavelength
λp
IF = 20mA
568
nm
Dominant Wavelength
λD
IF = 20mA
570
nm
Luminous Intensity
IV
IF = 20mA
40
mcd
50% Power Angle
2θ½
IF = 20mA
Min.
---
Typ.
Max
Unit
2.00
2.60
V
10
uA
130
---
Deg
■ Material
Item
Reflector
Wire
Encapsulate
Chip
Material
/
Gold
Silicone
AlGaInP
Note:
1.Luminous Intensity is based on the Foryard standards.
2.Pay attention about static for InGaN
Http://www.foryard.com
Page
:
3/8
Model. No.
Rev.
Model No.
FYLS-0603AUGC
A
:FYLS-0603AUGC
■ Typical Eletrical/Optical Characteristics Curves(Ta=25ºC Unless Otherwise Noted)
Relative Lumionous Intensity(LOP @max=1)
GaP or AlGaInP
Http://www.foryard.com
Page
:
4/8
Model. No.
Rev.
Model No.
FYLS-0603AUGC
A
:FYLS-0603AUGC
■ Packing Diagram
Note: The specifications are subject to change without notice. Please contact us for updated information.
Http://www.foryard.com
Page
:
5/8
Model. No.
Rev.
Model No.
FYLS-0603AUGC
A
:FYLS-0603AUGC
■ Packing Diagram
0603A 4000/Reel
Reel
39.0
OUTSIDE LABEL
.0
32
30
FORYARD
1
8
.5
O P T O E L E C T R O N I C S
0
.
8
3
www.foryard.com
9 Reels /Box
.5
11
6 Boxes/Carton
FORYARD
O P T O E L E C T R O N I C S
LED
PN:FYLS-XXXXX-XX
Qty:XXXXX PCS
Date:xxxx/xx/xx
GW: XX KG
PASS
QC: QC
NW: XX KG
xxxxxxxxxx
RoHS
ATTENTION
OUTSIDE LABEL
Note: The specifications are subject to change without notice. Please contact us for updated information.
Http://www.foryard.com
Page
:
6/8
Model. No.
Rev.
Model No.
FYLS-0603AUGC
A
:FYLS-0603AUGC
■ Precautions for use:
1. Storage
To prevent moisture absorption into SMD LEDs during the transportation and storage , the LEDs are packed
in a moisture-barrier bag. Desiccants and a humidity indicator are packed together with the LEDs as
secondary protection
℃ and < 90% RH is 12 months. Baking is
The shelf life of LEDs stored in the original sealed bag at <40
required if the shelf life has expired
Before opening the packaging , check for air leaks in the bag.
℃ and < 60% RH. Under these conditions,
After the bag is opened, the SMD LEDs must be stored at <30
SMD LEDs must be used within 24 hours. If the LEDs are not within 24 hours after removal from the bag ,
baking is required Take the material out of the packaging bag before baking. Do not open the oven door
frequently during the baking process.
2. Soldering
(1) Manual soldering with a soldering Iron
℃
Use a soldering iron of less than 25 watts is recommended . The iron temperature must be kept below 315
And soldering time no more than 2 seconds.
The epoxy resin of an SMD LED should not contact the tip of the soldering iron.
No mechanical stress should be exerted on the resin portion of an SMD LED during soldering.
Handling of an SMD LED should be done only when the package has been cooled down to below 40
℃
(2)Reflow soldering
Temperature profile
Temperature
Peak temperature
Melting-point
Pre-heat
Soak
Reflow
Cooling
Time
Http://www.foryard.com
Page
:
7/8
FYLS-0603AUGC
A
Model. No.
Rev.
Model No.
:FYLS-0603AUGC
Solder=Sn63-Pb37
Solder= Pb-Free
℃
℃
Average ramp-up rate:4 /sec.max
Average ramp-up rate:4 /sec.max
Peak preheat temperature:100-150
Peak preheat temperature:100-150
℃
preheat time:100seconds.max
preheat time:100seconds.max
ramp-down rate:6 /sec.max
ramp-down rate:6 /sec.max
Peak temperature:230
Peak temperature:250
℃
℃
℃
℃
Time within 5 of actual peak
temperature=10 sec. max
Duration above 183
℃ is 80 sec. max
℃
℃
℃ of actual peak temperature=10 sec.
Duration above 217℃ is 80 sec. max
Time within 5
max
SMD LED should not be modified after soldering. If modification cannot be avoided, the modification
must be pre-qualified to avoid damage to the SMD LEDs.
Reflow soldering should not be done more than one time
No stress should be exerted on the package during soldering.
(3) Recommend Soldering pad design(unit=mm)
3. Static Electricity
Static Electricity and surge voltage damage the LEDs. So it is recommended that an ESD wrist band,
ESD shoe strap or an anti-electrostatic glove be used when handling the LEDs.
All devices, equipment and machinery must be properly grounded
4. Others
Reverse voltage should not exceed the absolute maximum rating on the data sheet. The colour of the LEDs
is changed slightly an operating current and thermal.
This device should not be used in any type of fluid such as water, oil, organic solvent and etc
When washing is required, IPA (Isopropyl Alcohol) should be used.
The influence of ultrasonic cleaning on the leds depends on factors such as ultrasonic power and the way.
High-brightness LED light may injure human eyes. Avoid looking directly into lighted LED
The appearance and specifications of the product may be modified for improvement without notice.
Http://www.foryard.com
Page
:
8/8