Model. No. Rev. FYLS-0805RGBC A PRODUCT SPECIFICATION Model No. ：FYLS-0805RGBC Features: ■TOP LED Type ■Size (mm):2.0*1.25*1.1 ■Emitting Color:Red/Green/Blue ■SMT package ■Lens Type: Water clear. ■Pb-free Reflow soldering application ■RoHS Compliant ■Light Strips ■LCD Backlight ■Decorative lighting ■Indicators ■Interior automotive ■Illuminations ■Mobile Phones CUSTOMER APPROVED SIGNATURES Applications: APPROVED BY NINGBO FORYARD OPTOELECTRONICS CO.,LTD Add:NO.115 Qixin Road Ningbo Zhejiang China Tel: 0086-574-87933652 87927870 87922206 Fax: 0086-574-87927917 E-mail:[email protected] ( General) Http://www.foryard.com CHECKED BY PREPARED BY Zip:315051 Http://www.foryard.com Page ： 1/8 Model. No. Rev. Model No. FYLS-0805RGBC A ：FYLS-0805RGBC ■ Mechanical Dimensions Notes: 1. Dimension in millimeter [inch], tolerance is ±0.25 [.010]. 2.The specifications,characteristics and technical data described in the datasheet are subject to change without prior notice. Http://www.foryard.com Page ： 2/8 FYLS-0805RGBC A Model. No. Rev. Model No. ：FYLS-0805RGBC ■ Absolute Maximun Ratings(Ta=25ºC) Items Unit R G B IF 30 30 30 mA Peak Forward Current* IFP 100 100 100 mA Power Dissipation PD 78 100 100 Mw Forward Current(DC) ■ Absolute maximum Rating Symbol Operation Temperature Topr Storage Temperature Tstg Reverse Voltage VR Soldering Temperature Tsol ≦ º～ º -40ºC～+100ºC ℃ ℃ -30 C +80 C 5 Reflow Soldering:250 ≦ ℃/5sec V *Pulse width 1msec duty 1/10 Typical Electrical &Optical Charcteristics(Ta=25ºC) Items Forward Voltage Symbol Condition R G B IF = 20mA VF Reverse Current Color Min Max 2.00 3.20 3.20 2.60 3.60 3.60 10 VR = 5V IR R G Peak Emission Wavelength λp B R Dominant Wavelength λD G B R Luminous Intensity IV G B 50% Power Angle 2θ½ IF = 20mA IF = 20mA IF = 20mA IF = 20mA --- 645 525 468 631 520 470 57 250 57 120 Unit V uA nm nm mcd --- Deg ■ Material Item Reflector Wire Encapsulate Chip Material R / Gold Silicone AlGaInP Material G / Gold Silicone InGaN Material / Gold B Note: 1.Luminous Intensity is based on the Foryard standards. Silicone InGaN 2.Pay attention about static for InGaN Http://www.foryard.com Page ： 3/8 Model. No. Rev. Model No. FYLS-0805RGBC A ：FYLS-0805RGBC ■ Typical Eletrical/Optical Characteristics Curves(Ta=25ºC Unless Otherwise Noted) Spectral Reduance Normalized Response (1) (2) (3) Relative Lumionous Intensity(LOP @max=1) Wave Length(nm) Relative Luminous intensity vs Forward current Forward Current Vs Forward Voltage Relative Intensity (Lop@20mA=1) Forward Current(mA) 50 40 30 20 10 0 1.9 2.1 2.3 2.5 2.7 2.9 3.1 3.3 3.5 3.7 3.9 Forward Current IF(mA) Forward Voltage(V) Luminous Intensity Vs. Ambient Temperature 60 50 40 30 InGaN/SiC AlGaInP InGaN/Al2O3 20 10 0 0 10 20 30 40 50 60 70 80 90 Relative Luminous Intensity Forward Current(mA) Forward Current Derating Curve Ambient Temperature TA( ) Http://www.foryard.com Ambient Temperature CTA( ) Page ： 4/8 Model. No. Rev. Model No. FYLS-0805RGBC A ：FYLS-0805RGBC ■ Packing Diagram Note: The specifications are subject to change without notice. Please contact us for updated information. Http://www.foryard.com Page ： 5/8 Model. No. Rev. Model No. FYLS-0805RGBC A ：FYLS-0805RGBC ■ Packing Diagram 0805 4000/Reel Reel 39.0 OUTSIDE LABEL .0 32 30 FORYARD 1 8 . 5 O P T O E L E C T R O N I C S 0 . 8 3 www.foryard.com 9 Reels /Box .5 11 6 Boxes/Carton FORYARD O P T O E L E C T R O N I C S LED PN:FYLS-XXXXX-XX Qty:XXXXX PCS Date:xxxx/xx/xx GW: XX KG PASS QC: QC NW: XX KG xxxxxxxxxx RoHS ATTENTION OUTSIDE LABEL Note: The specifications are subject to change without notice. Please contact us for updated information. Http://www.foryard.com Page ： 6/8 Model. No. Rev. Model No. FYLS-0805RGBC A ：FYLS-0805RGBC ■ Precautions for use: 1. Storage To prevent moisture absorption into SMD LEDs during the transportation and storage , the LEDs are packed in a moisture-barrier bag. Desiccants and a humidity indicator are packed together with the LEDs as secondary protection ℃ and < 90% RH is 12 months. Baking is The shelf life of LEDs stored in the original sealed bag at <40 required if the shelf life has expired Before opening the packaging , check for air leaks in the bag. ℃ and < 60% RH. Under these conditions, After the bag is opened, the SMD LEDs must be stored at <30 SMD LEDs must be used within 24 hours. If the LEDs are not within 24 hours after removal from the bag , baking is required Take the material out of the packaging bag before baking. Do not open the oven door frequently during the baking process. 2. Soldering (1) Manual soldering with a soldering Iron ℃ Use a soldering iron of less than 25 watts is recommended . The iron temperature must be kept below 315 And soldering time no more than 2 seconds. The epoxy resin of an SMD LED should not contact the tip of the soldering iron. No mechanical stress should be exerted on the resin portion of an SMD LED during soldering. Handling of an SMD LED should be done only when the package has been cooled down to below 40 ℃ (2)Reflow soldering Temperature profile Temperature Peak temperature Melting-point Pre-heat Soak Reflow Cooling Time Http://www.foryard.com Page ： 7/8 Model. No. Rev. Model No. FYLS-0805RGBC A ：FYLS-0805RGBC Solder=Sn63-Pb37 Solder= Pb-Free ℃ Average ramp-up rate:4 /sec.max Peak preheat temperature:100-150 ℃ ℃/sec.max Peak preheat temperature:100-150℃ Average ramp-up rate:4 preheat time:100seconds.max preheat time:100seconds.max ramp-down rate:6 /sec.max ramp-down rate:6 /sec.max Peak temperature:230 Peak temperature:250 Time within 5 of actual peak temperature=10 sec. max Time within 5 max ℃ ℃ Duration above 183 ℃ ℃ ℃ is 80 sec. max ℃ ℃ of actual peak temperature=10 sec. Duration above 217℃ is 80 sec. max SMD LED should not be modified after soldering. If modification cannot be avoided, the modification must be pre-qualified to avoid damage to the SMD LEDs. Reflow soldering should not be done more than one time No stress should be exerted on the package during soldering. (3) Recommend Soldering pad design(unit=mm) 3. Static Electricity Static Electricity and surge voltage damage the LEDs. So it is recommended that an ESD wrist band, ESD shoe strap or an anti-electrostatic glove be used when handling the LEDs. All devices, equipment and machinery must be properly grounded 4. Others Reverse voltage should not exceed the absolute maximum rating on the data sheet. The colour of the LEDs is changed slightly an operating current and thermal. This device should not be used in any type of fluid such as water, oil, organic solvent and etc When washing is required, IPA (Isopropyl Alcohol) should be used. The influence of ultrasonic cleaning on the leds depends on factors such as ultrasonic power and the way. High-brightness LED light may injure human eyes. Avoid looking directly into lighted LED The appearance and specifications of the product may be modified for improvement without notice. Http://www.foryard.com Page ： 8/8