Infineon-DPS310 Pressure Sensor-PB-v01_00-EN

Product Brief
DPS310 Digital Barometric Pressure
Sensor for Mobile and Wearable Devices
Description
The DPS310 is a miniaturized Digital Barometric Air Pressure Sensor with a high accuracy level and low current consumption. The DPS310 is both a pressure and temperature
sensor. The pressure sensor element is based on a capacitive principle which guarantees
high precision during temperature changes. The small package makes the DPS310 ideal
for mobile applications and wearable devices.
The DPS310’s internal signal processor converts the output from the pressure and
temperature sensor elements to 24-bit results. Each pressure sensor has been calibrated
individually and contains calibration coefficients. The coefficients are used in the application to convert the measurement results to true pressure and temperature values.
The sensor has a FIFO that can store the latest 32 measurements. Since the host processor can remain in a sleep mode for a longer period between readouts, a FIFO can reduce
the system power consumption.
Sensor measurements and calibration coefficients are available via the serial I2C / SPI
interface.
Typical Applications
„„ Indoor navigation
–– Floor detection e.g. in shopping malls and parking garages
„„ Health and sports
–– Accurate elevation gain and vertical speed
„„ Outdoor navigation
–– GPS start-up time and accuracy improvement
–– Dead-reckoning e.g. in tunnels
„„ Local weather station
www.infineon.com
Features
„„ Operation range:
–– Pressure: 300 … 1200hPa
–– Temperature: -40 … 85°C
„„ Pressure level precision:
–– ±0.006hPa (or ±5cm)
(high-precision mode)
„„ Pressure sensor relative accuracy:
–– ±0.06hPa (or ±0.5m)
„„ Temperature accuracy:
–– ±0.5°C
„„ Pressure temperature sensitivity:
–– < 0.5Pa/K
„„ Measurement time:
–– Low-power mode: 3ms
„„ Average current consumption:
–– Low power: 3µA
(1 measurement/sec.)
–– Standby: < 1µA
„„ Supply voltage:
–– VDDIO: 1.2 … 3.6V
–– VDD: 1.7 … 3.6V
„„ Operating modes:
–– Command (manual)
–– Background (automatic)
–– Standby
„„ Interface:
–– I2C and SPI
(both with optional interrupt)
„„ Package dimensions:
–– 8-pin LGA
–– 2.0mm x 2.5mm x 1.0mm
Product Brief
Pressure Sensor for Mobile Devices
Digital Barometric Air Pressure Sensor
Functional Block Diagram
Temperature
Sensor
MUX
Digital
Signal
Processing
ADC
Calibration
Coefficients
Capacitive
Pressure
Sensor
Digital
Core
Digital
Interface
Memory
Interface
Voltage
Regulators
I2C/SPI
VDDIO
FIFO
VDD
Application Circuit Example (in I2C configuration)
Processor
R
I2C Serial Interface
VDDIO
SDI
SDA
SCK
SCK
Interrupt (optional)
INT
N.C.
SDO
VDDIO
Pressure Sensor
CSB
GND
1.2 … 3.6V
C
GND
VDD
1.7 … 3.6V
C
Pin Configuration (Top View)
VDD
8
1
GND
Pin
Name
Function
1
GND
Ground
2
CSB
Chip Select
SDI
Serial Data In
GND
7
2
CSB
3
4
SCK
Serial Clock
VDDIO
6
3
SDI
5
SDO
Serial Data Out
6
VDDIO
Digital Interface Supply
7
GND
Ground
8
VDD
Analog Supply
SDO
5
4
SCK
Vent hole
Published by
Infineon Technologies AG
85579 Neubiberg, Germany
© 2015 Infineon Technologies AG.
All Rights Reserved.
Visit us:
www.infineon.com
Order Number: B132-I0080-V1-7600-EU-EC-P
Date: 01 / 2015
Attention please!
The information given in this document shall in no event
be regarded as a guarantee of conditions or characteristics
(“Beschaffenheitsgarantie”). With respect to any examples
or hints given herein, any typical values stated herein and/
or any information regarding the application of the device,
Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation
warranties of non-infringement of intellectual property
rights of any third party.
Information
For further information on technology, delivery terms and
conditions and prices please contact your nearest Infineon
Technologies Office (www.infineon.com).
Warnings
Due to technical requirements components may contain
dangerous substances. For information on the types in
question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only
be used in life-support devices or systems with the express
written approval of Infineon Technologies, if a failure of
such components can reasonably be expected to cause
the failure of that life-support device or system, or to affect
the safety or effectiveness of that device or system. Life
support devices or systems are intended to be implanted in the human body, or to support and/or maintain and
sustain and/or protect human life. If they fail, it is reasonable
to assume that the health of the user or other persons may
be endangered.