Download

IL800-Series Isolators
DC-Correct High Speed Digital Isolators
Features
Functional Diagrams
IL810
IL814
•
•
•
•
•
•
•
•
•
•
•
•
DC-correct
−40ºC to 125ºC operating temperature
110 Mbps
10 ns propagation delay
1.3 mA/channel typical quiescent current
50 kV/μs typ.; 30 kV/μs min. common mode transient immunity
1000 VRMS/1500 VDC high voltage endurance
44000 year barrier life
3 V to 5 V power supplies
Low EMC footprint
8-pin MSOP and SOIC; 0.15", 0.3", and True 8™ mm 16-pin SOIC packages
UL 1577 recognized; IEC 60747-5-5 (VDE 0884) certified
Applications
IL811
IL812
IL815
•
•
•
•
•
•
•
•
•
•
•
ADCs and DACs
Digital Fieldbus
RS-485 and RS-422
Multiplexed data transmission
Data interfaces
Board-to-board communication
Digital noise reduction
Ground loop elimination
Peripheral interfaces
Parallel bus
Logic level shifting
Description
IL800-Series isolators are high-speed, high temperature dc-correct isolators.
An internal refresh clock ensures the outputs respond to dc states on inputs
within a maximum of 9 µs.
IL821
The devices use NVE’s patented* IsoLoop® spintronic Giant
Magnetoresistive (GMR) technology.
IL816
A unique ceramic/polymer composite barrier provides excellent isolation
and virtually unlimited barrier life.
IL817
IsoLoop is a registered trademark of NVE Corporation.
*U.S. Patent numbers 5,831,426; 6,300,617 and others.
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
REV. E
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL800-Series Isolators
Absolute Maximum Ratings(1)
Parameters
Storage Temperature
Ambient Operating Temperature
Supply Voltage
Input Voltage
Output Voltage
Output Current Drive
Lead Solder Temperature
ESD
Symbol
TS
TA
VDD1, VDD2
VI
VO
IO
Min.
−55
−40
−0.5
−0.5
−0.5
Typ.
Max.
150
125
7
VDD+0.5
VDD+0.5
10
260
2
Units
°C
°C
V
V
V
mA
°C
kV
Test Conditions
10 sec.
HBM
Recommended Operating Conditions
Parameters
Ambient Operating Temperature
Supply Voltage
Logic High Input Voltage
Logic Low Input Voltage
Input Signal Rise and Fall Times(10)
Symbol
TA
VDD1, VDD2
VIH
VIL
tIR, tIF
Min.
−40
3.0
2.4
0
Typ.
Max.
125
5.5
VDD
0.8
Units
°C
V
V
V
Test Conditions
DC-Correct
Insulation Specifications
Parameters
Creepage
MSOP
Distance
0.15" SOIC (8 or 16 pin)
(external)
0.3" SOIC
Total Barrier Thickness (internal)
Leakage Current
Barrier Resistance
Barrier Capacitance
Comparative Tracking Index
High Voltage Endurance
AC
(Maximum Barrier Voltage
for Indefinite Life)
DC
Symbol
RIO
CIO
CTI
VIO
Min.
3.0
4.0
8.03
0.012
Typ.
Max.
Units
Test Conditions
mm
8.3
0.013
0.2
>1014
4
Per IEC 60601
≥175
1000
mm
µA
Ω
pF
V
VRMS
1500
VDC
Barrier Life
240 VRMS, 60 Hz
500 V
f = 1 MHz
Per IEC 60112
At maximum
operating temperature
Years
100°C, 1000 VRMS, 60%
CL activation energy
Max.
Units
Test Conditions
150
°C/W
°C/W
°C/W
°C/W
mW
44000
Package Characteristics
Parameters
Thermal Resistance
MSOP
0.15" 8-pin SOIC
0.15" 16-pin SOIC
0.3" 16-pin SOIC
Package Power Dissipation
Symbol
Min.
Typ.
θJC
θJC
θJC
θJC
168
144
41
28
PPD
Thermocouple at
center underside
of package
f = 1 MHz, VDD = 5 V
2
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL800-Series Isolators
Safety and Approvals
IEC 60747-5-5 (VDE 0884) (File Number 5016933-4880-0001)
• Working Voltage (VIORM) 600 VRMS (848 VPK); basic insulation; pollution degree 2
• Transient overvoltage (VIOTM) and surge voltage (VIOSM) 4000 VPK
• Each part tested at 1590 VPK for 1 second, 5 pC partial discharge limit
• Samples tested at 4000 VPK for 60 sec.; then 1358 VPK for 10 sec. with 5 pC partial discharge limit
IEC 61010-1 (Edition 2; TUV Certificate Numbers N1502812; N1502812-101)
Reinforced Insulation; Pollution Degree II; Material Group III
Part No. Suffix
-1
-3
None
Package
MSOP
SOIC
Wide-body SOIC/True 8™
Working Voltage
150 VRMS
150 VRMS
300 VRMS
UL 1577 (Component Recognition Program File Number E207481)
Each part other than MSOP tested at 3000 VRMS (4240 VPK) for 1 second; each lot sample tested at 2500 VRMS (3530 VPK) for 1 minute
MSOP tested at 1200 VRMS (1768 VPK) for 1 second; each lot sample tested at 1500 VRMS (2121 VPK) for 1 minute
Soldering Profile
Per JEDEC J-STD-020C, MSL 1
3
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL800-Series Isolators
IL810-1/IL810-3 Pin Connections
1
2
VDD1
IN
3
SYNC
4
5
6
GND1
GND2
OUT
7
VOE
8
VDD2
Supply voltage
Data in
Internal refresh clock disable
(normally enabled and internally
held low with 10 kΩ)
Ground return for VDD1
Ground return for VDD2
Data out
Output enable
(internally held low with 100 kΩ)
Supply voltage
VDD1
VDD2
IN
VOE
SYNC
OUT
GND1
GND2
IL810-1/IL810-3
IL811-1/IL811-3 Pin Connections
1
2
3
4
5
6
7
8
VDD1
IN1
IN2
GND1
GND2
OUT2
OUT1
VDD2
Supply voltage
Data in, channel 1
Data in, channel 2
Ground return for VDD1
Ground return for VDD2
Data out, channel 2
Data out, channel 1
Supply voltage
VDD1
8 VDD2
1
IN1 2
7 OUT1
IN2 3
6 OUT2
GND1 4
5 GND2
IL811-1/IL811-3
IL812-3 Pin Connections
1
2
3
4
5
6
7
8
VDD1
IN1
OUT2
GND1
GND2
IN2
OUT1
VDD2
Supply voltage
Data in, channel 1
Data out, channel 2
Ground return for VDD1
Ground return for VDD2
Data in, channel 2
Data out, channel 1
Supply voltage
VDD1
VDD2
IN1
OUT1
OUT2
IN2
GND1
GND2
IL812-3
IL821-3 Pin Connections
1
2
3
4
5
6
7
8
VDD1
OUT1
IN2
GND1
GND2
OUT2
IN1
VDD2
Supply voltage
Data out, channel 1
Data in, channel 2
Ground return for VDD1
Ground return for VDD2
Data out, channel 2
Data in, channel 1
Supply voltage
VDD1
VDD2
OUT1
IN1
IN2
OUT2
GND1
GND2
IL821-3
4
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL800-Series Isolators
IL814/IL814-3 Pin Connections
1
VDD1
2
GND1
3
4
5
6
IN1
IN2
OUT3
NC
7
VOE
8
GND1
9
GND2
10
11
12
13
14
NC
NC
IN3
OUT2
OUT1
15
GND2
16
VDD2
Supply voltage 1
Ground return for VDD1
(pin 2 internally connected to pin 8)
Data in, channel 1
Data in, channel 2
Data out, channel 3
No connection
Output enable, channel 3
(internally held low with 100 kΩ)
Ground return for VDD1
(pin 8 internally connected to pin 2)
Ground return for VDD2
(pin 9 internally connected to pin 15)
No connection
No connection
Data in, channel 3
Data out, channel 2
Data out, channel 1
Ground return for VDD2
(pin 15 internally connected to pin 9)
Supply voltage
VDD1
VDD2
GND1
GND2
IN1
OUT1
IN2
OUT2
OUT3
IN3
NC
NC
VOE
NC
GND2
GND1
IL814/IL814-3
IL815/IL815-3 Pin Connections
1
VDD1
Supply voltage
Ground return for VDD1
2
GND1
(pin 2 internally connected to pin 8)
3
IN1
Data in, channel 1
4
IN2
Data in, channel 2
5
IN3
Data in, channel 3
6
IN4
Data in, channel 4
Internal refresh clock disable
7
SYNC* (normally enabled and
internally held low with 10 kΩ)
Ground return for VDD1
8
GND1
(pin 8 internally connected to pin 2)
Ground return for VDD2
9
GND2
(pin 9 internally connected to pin 15)
Output enable
10
VOE*
(internally held low with 100 kΩ)
11
OUT4
Data out, channel 4
12
OUT3
Data out, channel 3
13
OUT2
Data out, channel 2
14
OUT1
Data out, channel 1
Ground return for VDD2
15
GND2
(pin 15 internally connected to pin 9)
16
VDD2
Supply voltage
*Wide-body version (IL815TE) only.
No internal connections to pins 7 or 10
in narrow-body (IL815T-3E) version.
VDD1
VDD2
GND1
GND2
IN1
OUT1
IN2
OUT2
IN3
OUT3
IN4
OUT4
SYNC
VOE
GND1
GND2
IL815/IL815-3*
5
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL800-Series Isolators
IL816/IL816-3 Pin Connections
1
VDD1
2
GND1
3
4
5
6
IN1
IN2
OUT3
OUT4
7
VOE
8
GND1
9
GND2
10
11
12
13
14
NC
IN4
IN3
OUT2
OUT1
15
GND2
16
VDD2
Supply voltage
Ground return for VDD1
(pin 2 internally connected to pin 8)
Data in, channel 1
Data in, channel 2
Data out, channel 3
Data out, channel 4
Output enable, channels 3 and 4
(internally held low with 100 kΩ)
Ground return for VDD1
(pin 8 internally connected to pin 2)
Ground return for VDD2
(pin 9 internally connected to pin 15)
No connection
Data in, channel 4
Data in, channel 3
Data out, channel 2
Data out, channel 1
Ground return for VDD2
(pin 15 internally connected to pin 9)
Supply voltage
VDD1
1
16
VDD2
GND1
2
15
GND2
IN1
3
14
OUT1
IN2
4
13
OUT2
OUT3
5
12
IN3
OUT4
6
11
IN4
VOE
7
10
NC
GND1
8
9
GND2
IL816/IL816-3
IL817/IL817-3 Pin Connections
1
VDD1
2
GND1
3
4
5
6
IN1
IN2
IN3
OUT4
7
VOE
8
GND1
9
GND2
10
11
12
13
14
NC
IN4
OUT3
OUT2
OUT1
15
GND2
16
VDD2
Supply voltage
Ground return for VDD1
(pin 2 internally connected to pin 8)
Data in, channel 1
Data in, channel 2
Data in, channel 3
Data out, channel 4
Output enable, channel 4
(internally held low with 100 kΩ)
Ground return for VDD1
(pin 8 internally connected to pin 2)
Ground return for VDD2
(pin 9 internally connected to pin 15)
No connection
Data in, channel 4
Data out, channel 3
Data out, channel 2
Data out, channel 1
Ground return for VDD2
(pin 15 internally connected to pin 9)
Supply voltage
VDD1
1
16
VDD2
GND1
2
15
GND2
IN1
3
14
OUT1
IN2
4
13
OUT2
IN3
5
12
OUT3
OUT4
6
11
IN4
VOE
7
10
NC
GND1
8
9
GND2
IL817/IL817-3
6
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL800-Series Isolators
IL821 Pin Connections
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
GND1
VDD1
OUT1
IN2
NC
GND1
GND2
NC
OUT2
IN1
VDD2
GND2
Ground return for VDD1
(pins 1, 2, 7, and 8 internally connected)
Supply voltage
Data out, channel 1
Data in, channel 2
No connection
Ground return for VDD1
(pins 1, 2, 7, and 8 internally connected)
Ground return for VDD2
(pins 9, 10, 15, and 16 internally connected)
No connection
Data out, channel 2
Data in, channel 1
Supply voltage
Ground return for VDD2
(pins 9, 10, 15, and 16 internally connected)
GND1
1
16
GND2
GND1
2
15
GND2
VDD1
3
14
VDD2
OUT1
4
13
IN1
IN2
5
12
OUT2
NC
6
11
NC
GND1
7
10
GND2
GND1
8
9
GND2
IL821
7
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL800-Series Isolators
Timing Diagrams
Legend
tPLH
tPHL
tPW
tPLZ
tPZH
tPHZ
tPZL
tR
tF
Propagation Delay, Low to High
Propagation Delay, High to Low
Minimum Pulse Width
Propagation Delay, Low to High Impedance
Propagation Delay, High Impedance to High
Propagation Delay, High to High Impedance
Propagation Delay, High Impedance to Low
Rise Time
Fall Time
Truth Tables
SYNC
Output Enable
VI
L
H
L
H
VOE
L
L
H
H
VO
L
H
Z
Z
SYNC
0
1
Internal Refresh Clock
Enabled
Disabled
Note: SYNC should be left open or connected
to GND to enable the internal refresh clock,
or connected to VDD to disable the internal clock.
8
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL800-Series Isolators
Parameters
Input Quiescent Supply Current
IL810, IL811, IL815
IL812, IL814, IL817, IL821
IL816
Output Quiescent Supply Current
IL810, IL812, IL821
IL811, IL814, IL816
IL815
IL817
Logic Input Current
3.3 Volt Electrical Specifications (Tmin to Tmax unless otherwise stated)
Symbol
Min.
Typ.
Max.
Units
IDD1
15
1.3
2.6
30
1.8
3.6
µA
mA
mA
IDD2
1.3
2.6
5.2
3.9
1.8
3.6
7.2
5.4
10
mA
mA
mA
mA
µA
II
Logic High Output Voltage
VOH
Logic Low Output Voltage
VOL
Maximum Data Rate
Pulse Width(7)
Propagation Delay Input to Output
(High to Low)
Propagation Delay Input to Output
(Low to High)
Propagation Delay Enable to Output
(High to High Impedance)
Propagation Delay Enable to Output
(Low to High Impedance)
Propagation Delay Enable to Output
(High Impedance to High)
Propagation Delay Enable to Output
(High Impedance to Low)
Pulse Width Distortion(2)
Propagation Delay Skew(3)
Output Rise Time (10%−90%)
Output Fall Time (10%−90%)
Common Mode Transient Immunity
(Output Logic High or Logic Low)(4)
Channel-to-Channel Skew
SYNC Internal Clock Off Time(11)
Dynamic Power Consumption(6)
Power Frequency Magnetic Immunity
Pulse Magnetic Field Immunity
Damped Oscillatory Magnetic Field
Cross-axis Immunity Multiplier(9)
−10
VDD − 0.1
0.8 x VDD
VDD
0.9 x VDD
0
0.5
V
0.1
0.8
Switching Specifications (VDD = 3.3 V)
100
110
PW
10
V
Mbps
ns
Test Conditions
IO = −20 µA, VI = VIH
IO = −4 mA, VI = VIH
IO = 20 µA, VI = VIL
IO = 4 mA, VI = VIL
CL = 15 pF
VO 50% points;
tPHL
12
18
ns
CL = 15 pF
tPLH
12
18
ns
CL = 15 pF
tPHZ
5
ns
CL = 15 pF
tPLZ
5
ns
CL = 15 pF
tPZH
5
ns
CL = 15 pF
tPZL
5
ns
CL = 15 pF
3
6
4
4
ns
ns
ns
ns
CL = 15 pF
CL = 15 pF
CL = 15 pF
CL = 15 pF
VCM = 1500 VDC
tTRANSIENT = 25 ns
CL = 15 pF
PWD
tPSK
tR
tF
|CMH|,|CML|
2
4
2
2
30
50
tCSK
tOFF
2
140
kV/µs
3
5
240
Magnetic Field Immunity(8) (VDD2= 3V, 3V<VDD1<5.5V)
HPF
1000
1500
HPM
1800
2000
HOSC
1800
2000
KX
2.5
ns
ns
μA/Mbps
A/m
A/m
A/m
per channel
50Hz/60Hz
tp = 8µs
0.1Hz – 1MHz
9
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL800-Series Isolators
Parameters
Input Quiescent Supply Current
IL810, IL811, IL815
IL812, IL814, IL817, IL821
IL816
Output Quiescent Supply Current
IL810, IL812, IL821
IL811, IL814, IL816
IL815
IL817
Logic Input Current
5 Volt Electrical Specifications (Tmin to Tmax unless otherwise stated)
Symbol
Min.
Typ.
Max.
Units
IDD1
24
1.8
3.6
40
2.5
5
µA
mA
mA
IDD2
1.8
3.6
7.2
5.4
2.5
5
10
7.5
10
mA
mA
mA
mA
µA
II
Logic High Output Voltage
VOH
Logic Low Output Voltage
VOL
Maximum Data Rate
Pulse Width(7)
Propagation Delay Input to Output
(High to Low)
Propagation Delay Input to Output
(Low to High)
Propagation Delay Enable to Output
(High to High Impedance)
Propagation Delay Enable to Output
(Low to High Impedance)
Propagation Delay Enable to Output
(High Impedance to High)
Propagation Delay Enable to Output
(High Impedance to Low)
Pulse Width Distortion(2)
Propagation Delay Skew(3)
Output Rise Time (10%−90%)
Output Fall Time (10%−90%)
Common Mode Transient Immunity
(Output Logic High or Logic Low)(4)
Channel-to-Channel Skew
SYNC Internal Clock Off Time(11)
Dynamic Power Consumption(6)
Power Frequency Magnetic Immunity
Pulse Magnetic Field Immunity
Damped Oscillatory Magnetic Field
Cross-axis Immunity Multiplier(9)
PW
−10
VDD − 0.1
0.8 x VDD
VDD
0.9 x VDD
0
0.5
V
0.1
0.8
Switching Specifications
100
110
10
V
Mbps
ns
Test Conditions
IO = −20 µA, VI = VIH
IO = −4 mA, VI = VIH
IO = 20 µA, VI = VIL
IO = 4 mA, VI = VIL
CL = 15 pF
VO 50% points
tPHL
10
15
ns
CL = 15 pF
tPLH
10
15
ns
CL = 15 pF
tPHZ
5
ns
CL = 15 pF
tPLZ
5
ns
CL = 15 pF
tPZH
5
ns
CL = 15 pF
tPZL
5
ns
CL = 15 pF
3
6
3
3
ns
ns
ns
ns
CL = 15 pF
CL = 15 pF
CL = 15 pF
CL = 15 pF
VCM = 1500 VDC
tTRANSIENT = 25 ns
CL = 15 pF
PWD
tPSK
tR
tF
|CMH|,|CML|
2
4
1
1
30
50
tCSK
tOFF
3
200
kV/µs
5
5
340
Magnetic Field Immunity(8) (VDD2= 5V, 3V<VDD1<5.5V)
HPF
2,800
3,500
HPM
4,000
4,500
HOSC
4,000
4,500
KX
2.5
ns
ns
μA/Mbps
A/m
A/m
A/m
per channel
50Hz/60Hz
tp = 8 µs
0.1Hz – 1MHz
10
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL800-Series Isolators
Notes (apply to both 3.3 V and 5 V specifications):
1.
Absolute maximum means the device will not be damaged if operated under these conditions. It does not guarantee performance.
2.
PWD is defined as |tPHL − tPLH|. %PWD is equal to PWD divided by pulse width.
3.
tPSK is the magnitude of the worst-case difference in tPHL and/or tPLH between devices at 25°C.
4.
CMH is the maximum common mode voltage slew rate that can be sustained while maintaining VO > 0.8 VDD2. CML is the maximum
common mode input voltage that can be sustained while maintaining VO < 0.8 V. The common mode voltage slew rates apply to both rising
and falling common mode voltage edges.
5.
Device is considered a two terminal device: pins on each side of the package are shorted.
6.
Dynamic power consumption is calculated per channel and is supplied by the channel’s input side power supply.
7.
Minimum pulse width is the minimum value at which specified PWD is guaranteed.
8.
The relevant test and measurement methods are given in the Electromagnetic Compatibility section on p. 9.
9.
External magnetic field immunity is improved by this factor if the field direction is “end-to-end” rather than to “pin-to-pin” (see diagram on p. 9).
10. If internal clock is used, devices will respond to DC states on inputs within a maximum of 9 µs. Outputs may oscillate if the SYNC input slew
rate is less than 1 V/ms.
11. toff is the maximum time for the internal refresh clock to shut down.
11
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL800-Series Isolators
Application Information
Electrostatic Discharge Sensitivity
Dynamic Power Consumption
This product has been tested for electrostatic sensitivity to the
limits stated in the specifications. However, NVE recommends that
all integrated circuits be handled with appropriate care to avoid
damage. Damage caused by inappropriate handling or storage could
range from performance degradation to complete failure.
IsoLoop Isolators achieve their low power consumption from the
way they transmit data across the isolation barrier. A magnetic field
is created around the GMR Wheatstone bridge by detecting the
edge transitions of the input logic signal and converting them to
narrow current pulses. Depending on the direction of the magnetic
field, the bridge causes the output comparator to switch following
the input logic signal. Since the current pulses are narrow, about
2.5 ns, the power consumption is independent of mark-to-space
ratio and solely dependent on frequency. This has obvious
advantages over optocouplers, which have power consumption
heavily dependent on mark-to-space ratio.
Electromagnetic Compatibility
IsoLoop Isolators have the lowest EMC footprint of any isolation
technology. IsoLoop Isolators’ Wheatstone bridge configuration
and differential magnetic field signaling ensure excellent EMC
performance against all relevant standards.
Additionally, on the IL810 and IL815, the internal clock can be
disabled for even better EMC performance.
DC Correctness, EMC, and the SYNC Function
NVE digital isolators have the lowest EMC noise signature of any
high-speed digital isolator on the market today because of the dc
nature of the GMR sensors used. It is perhaps fair to include optocouplers in that dc category too, but their limited parametric
performance, physically large size, and wear-out problems
effectively limit side by side comparisons between NVE’s isolators
and isolators coupled with RF, matched capacitors, or transformers.
These isolators are fully compliant with generic EMC standards
EN50081, EN50082-1 and the umbrella line-voltage standard for
Information Technology Equipment (ITE) EN61000. NVE has
completed compliance tests in the categories below:
EN50081-1
Residential, Commercial & Light Industrial
Methods EN55022, EN55014
EN50082-2: Industrial Environment
Methods EN61000-4-2 (ESD), EN61000-4-3 (Electromagnetic
Field Immunity), EN61000-4-4 (Electrical Transient Immunity),
EN61000-4-6 (RFI Immunity), EN61000-4-8 (Power Frequency
Magnetic Field Immunity), EN61000-4-9 (Pulsed Magnetic
Field), EN61000-4-10 (Damped Oscillatory Magnetic Field)
ENV50204
Radiated Field from Digital Telephones (Immunity Test)
IL800-Series isolators has an internal refresh clock which ensure
the synchronization of input and output within 9 μs of the supply
passing the 1.5 V threshold. The IL810 and IL815 allow external
control of the refresh clock through the SYNC pin thereby further
lowering the EMC footprint. This can be advantageous in
applications such as hi-fi, motor control and power conversion.
The isolators can be used with Power on Reset (POR) circuits
common in microcontroller applications, as the means of ensuring
the output of the device is in the same state as the input a short time
after power up. Figure 1 shows a practical Power on Reset circuit:
Immunity to external magnetic fields is even higher if the field
direction is “end-to-end” rather than to “pin-to-pin” as shown in the
diagram below:
Vdd2
Vdd1
1
8
7
SET
IN
POR
Cross-axis Field Direction
2
6
SYNC 3
4
5
Power Supply Decoupling
VOE
OUT
IL810
IL510
Both power supplies to these devices should be decoupled with low
ESR ceramic capacitors of at least 47 nF. Capacitors must be
located as close as possible to the VDD pins.
Fig. 1. Typical Power On Reset Circuit for IL810
After POR, the SYNC line goes high, the internal clock is disabled,
and the EMC signature is optimized. Decoupling capacitors are
omitted for clarity.
Maintaining Creepage
Creepage distances are often critical in isolated circuits. In addition to
meeting JEDEC standards, NVE isolator packages have unique creepage
specifications. Standard pad libraries often extend under the package,
compromising creepage and clearance. Similarly, ground planes, if used,
should be spaced to avoid compromising clearance. Package drawings
and recommended pad layouts are included in this datasheet.
12
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL800-Series Isolators
Illustrative Applications
Isolated A/D Converter
Bridge
Bias
Delta Sigma A/D
CS5532
Bridge +
Bridge -
SD OE
SD Out
Iso SD Out
CS
Iso CS
Iso SCK
SCK
IL814
Clock
Generator
OSC
A delta-sigma A-D converter interfaced with the three-channel IL814. Multiple channels can easily be combined using the IL814’s output enable function.
13
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL800-Series Isolators
12-Bit D/A Converter Isolation
SYNC
OE
D1
D2
Latch
D3
D4
SYNC
Data
Bus
OE
D5
D6
Latch
Vout
D7
D8
SYNC
OE
D9
D10
Latch
D11
D12
3 x IL815
IL515
12-Bit DAC
RESET
The IL815 four-channel isolator is ideally suited for parallel bus isolation. The circuit above uses three IL815s to isolate a 12-bit DAC. The SYNC function
automatically synchronizes the outputs to the inputs, ensuring correct data on the isolator outputs. After the reset pulse goes high, data transfer from input to
output is initiated by the leading edge of each changing data bit.
14
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL800-Series Isolators
Package Drawings
8-pin MSOP (-1 suffix)
Dimensions in inches (mm); scale = approx. 5X
0.114 (2.90)
0.122 (3.10)
0.016 (0.40)
0.027 (0.70)
0.114 (2.90)
0.122 (3.10)
0.189 (4.80)
0.197 (5.00)
0.032 (0.80)
0.043 (1.10)
0.005 (0.13)
0.009 (0.23)
0.010 (0.25)
0.016 (0.40)
0.024 (0.60)
0.028 (0.70)
0.002 (0.05)
0.006 (0.15)
NOTE: Pin spacing is a BASIC
dimension; tolerances
do not accumulate
8-pin SOIC Package (-3 suffix)
Dimensions in inches (mm); scale = approx. 5X
0.188 (4.77)
0.197 (5.00)
0.016 (0.4)
0.050 (1.3)
0.040 (1.02)
0.050 (1.27)
0.054 (1.4)
0.072 (1.8)
0.150 (3.8)
0.157 (4.0)
0.228 (5.8)
0.244 (6.2)
0.049 (1.24)
0.051 (1.30)
NOM
0.013 (0.3)
0.020 (0.5)
0.004 (0.1)
0.012 (0.3)
NOTE: Pin spacing is a BASIC
dimension; tolerances
do not accumulate
0.007 (0.2)
0.013 (0.3)
15
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL800-Series Isolators
0.15" 16-pin SOIC Package (-3 suffix)
Dimensions in inches (mm); scale = approx. 5X
0.013 (0.3)
0.020 (0.5)
NOM
0.007 (0.2)
0.013 (0.3)
0.386 (9.8)
0.394 (10.0)
Pin 1 identified
by either an
indent or a
marked dot
0.016 (0.4)
0.050 (1.3)
0.055 (1.40)
0.062 (1.58)
0.054 (1.4)
0.072 (1.8)
0.150 (3.81)
0.157 (3.99)
0.049 (1.24)
0.051 (1.30)
0.228 (5.8)
0.244 (6.2)
NOTE: Pin spacing is a BASIC
dimension; tolerances
do not accumulate
0.004 (0.1)
0.012 (0.3)
True8™ 0.3" 16-pin SOIC Package (no suffix)
Dimensions in inches (mm); scale = approx. 5X
0.033 (0.85)*
0.043 (1.10)
0.260 (6.60)*
0.280 (7.11)
0.013 (0.3)
0.020 (0.5)
0.007 (0.2)
0.013 (0.3)
0.397 (10.08)
0.413 (10.49)
0.017 (0.43)*
0.022 (0.56)
0.016 (0.4)
0.050 (1.3)
0.007 (0.18)*
0.010 (0.25)
0.092 (2.34)
0.105 (2.67)
Pin 1 identified by
either an indent
or a marked dot
0.08 (2.0)
0.10 (2.5)
0.292 (7.42)*
0.299 (7.59)
0.049 (1.24)
0.051 (1.30)
0.394 (10.00)
0.419 (10.64)
NOTE: Pin spacing is a BASIC
dimension; tolerances
do not accumulate
*Specified for True 8™ package to guarantee 8 mm creepage per IEC 60601.
0.004 (0.1)
0.012 (0.3)
16
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL800-Series Isolators
Ordering Information
IL 8 16 - 3 T E TR13
Bulk Packaging
Blank = Tube
TR7 = 7'' Tape and Reel
TR13 = 13'' Tape and Reel
Package
E = RoHS Compliant
Temperature Range
T = -40ºC to 125ºC
Package Type
-1 = 8-pin MSOP
-3 = 0.15'' 8-pin or 16-pin SOIC
Blank = True8™ 0.3'' 16-pin SOIC
Channels
10 = 1 Transmit Channel
11 = 2 Transmit Channels
12 = 1 Transmit Channel
1 Receive Channel
21 = 1 Transmit Channel
1 Receive Channel
(reverse pinout)
14 = 2 Transmit Channels;
1 Receive Channel
15 = 4 Transmit Channels
16 = 2 Transmit Channels;
2 Receive Channels
17 = 3 Transmit Channels;
1 Receive Channels
Base Part Number
8 = 110 Mbps, DC-Correct
Product Family
IL = Isolators
Available
Parts
IL810T-1E
IL810T-3E
IL811T-1E
IL811T-3E
IL812T-3E
IL821T-3E
IL814T-3E
IL814TE
IL815T-3E
IL815TE
IL816T-3E
IL816TE
IL817T-3E
IL817TE
IL821TE
Xmit
Ch.
1
1
2
2
1
1
2
2
4
4
2
2
3
3
1
Rcv.
Ch.
0
0
0
0
1
1
1
1
0
0
2
2
1
1
1
Package
MSOP-8
SOIC-8
MSOP-8
SOIC-8
SOIC-8
SOIC-8
0.15" SOIC-16
True8
0.15" SOIC-16
True8
0.15" SOIC-16
True8
0.15" SOIC-16
True8
True8
17
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL800-Series Isolators
ISB-DS-001-IL800-E
November 2013
Changes:
• Added IL821TE part type (16-pin True8 wide-body package).
• Added output enables to IL816 and IL817.
• Clarified pinouts for different package types.
• IEC 60747-5-5 (VDE 0884) certification.
• Upgraded from MSL 2 to MSL 1.
ISB-DS-001-IL800-D
August 2013
Changes:
• Tighter quiescent current specifications.
• Added IL817 part types.
ISB-DS-001-IL800-C
July 2013
Changes:
• Added IL812-3 and IL821-3 part types (8-pin SOIC packages).
ISB-DS-001-IL800-B
June 2013
Changes:
• Increased transient immunity specifications based on additional data.
ISB-DS-001-IL800-A
May 27, 2013
Changes:
• Added “T” to full part numbers to indicate 125°C max. operating temperature.
• Added two-channel bidirectional versions (IL812 and IL821).
• Added list of available part types.
ISB-DS-001-IL800-PREVIEW
May 3, 2013
Changes:
• Released product preview.
18
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL800-Series Isolators
Datasheet Limitations
The information and data provided in datasheets shall define the specification of the product as agreed between NVE and its customer, unless NVE and
customer have explicitly agreed otherwise in writing. All specifications are based on NVE test protocols. In no event however, shall an agreement be
valid in which the NVE product is deemed to offer functions and qualities beyond those described in the datasheet.
Limited Warranty and Liability
Information in this document is believed to be accurate and reliable. However, NVE does not give any representations or warranties, expressed or
implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information.
In no event shall NVE be liable for any indirect, incidental, punitive, special or consequential damages (including, without limitation, lost profits, lost
savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on
tort (including negligence), warranty, breach of contract or any other legal theory.
Right to Make Changes
NVE reserves the right to make changes to information published in this document including, without limitation, specifications and product descriptions
at any time and without notice. This document supersedes and replaces all information supplied prior to its publication.
Use in Life-Critical or Safety-Critical Applications
Unless NVE and a customer explicitly agree otherwise in writing, NVE products are not designed, authorized or warranted to be suitable for use in life
support, life-critical or safety-critical devices or equipment. NVE accepts no liability for inclusion or use of NVE products in such applications and such
inclusion or use is at the customer’s own risk. Should the customer use NVE products for such application whether authorized by NVE or not, the
customer shall indemnify and hold NVE harmless against all claims and damages.
Applications
Applications described in this datasheet are illustrative only. NVE makes no representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications and products using NVE products, and NVE accepts no liability for any
assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NVE product is suitable and fit for
the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customers. Customers should
provide appropriate design and operating safeguards to minimize the risks associated with their applications and products.
NVE does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s
applications or products, or the application or use by customer’s third party customers. The customer is responsible for all necessary testing for the
customer’s applications and products using NVE products in order to avoid a default of the applications and the products or of the application or use by
customer’s third party customers. NVE accepts no liability in this respect.
Limiting Values
Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the
device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the recommended
operating conditions of the datasheet is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the
quality and reliability of the device.
Terms and Conditions of Sale
In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NVE hereby expressly objects to
applying the customer’s general terms and conditions with regard to the purchase of NVE products by customer.
No Offer to Sell or License
Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication
of any license under any copyrights, patents or other industrial or intellectual property rights.
Export Control
This document as well as the items described herein may be subject to export control regulations. Export might require a prior authorization from national
authorities.
Automotive Qualified Products
Unless the datasheet expressly states that a specific NVE product is automotive qualified, the product is not suitable for automotive use. It is neither
qualified nor tested in accordance with automotive testing or application requirements. NVE accepts no liability for inclusion or use of non-automotive
qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall
use the product without NVE’s warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the
product for automotive applications beyond NVE’s specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies
NVE for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NVE’s
standard warranty and NVE’s product specifications.
19
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL800-Series Isolators
An ISO 9001 Certified Company
NVE Corporation
11409 Valley View Road
Eden Prairie, MN 55344-3617 USA
Telephone: (952) 829-9217
Fax: (952) 829-9189
www.nve.com
e-mail: [email protected]
©NVE Corporation
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
ISB-DS-001-IL800-E
November 2013
20
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation