FAST RECOVER RECTIFIER VOLTAGE RANGE CURRENT BY296 THRU BY299 100 to 800 Volts 2 .0Ampere FEATURES • • • • • DO-15 Low coat construction Fast switching for high efficency. Low reverse leakage High forward surge current capability High temperature soldering guaranteed: 260℃/10 secods/.375”(9.5mm)lead length at 5 lbs(2.3kg) tension .034(0.9) .028(0.7) 1.0(25.4) MIN. .300(7.6) .230(5.8) .140(3.6) .104(2.6) MECHANICAL DATA • • • • • • DIA. DIA. 1.0(25.4) MIN. Case: Transfer molded plastic Epoxy: UL94V-O rate flame retardant Polarity: Color band denotes cathode end Lead: Plated axial lead, solderable per MIL-STD-202E method 208C Mounting position: Any Weight: 0.014 ounce, 0.39 grams Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25OC ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% SYMBOLS VRRM VRMS VDC Maximum Repetitive Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current 0.375”(9.5mm) lead length at TA= 75℃ Peak Forward Surge Current 8.3mS single half sine wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage @ 2.0A TA = 25℃ Maximum DC Reverse Current at Rated DC Blocking Voltage TA = 100℃ Maximum Reverse Recovery Time (Note 3) T J=25℃ Typical Junction Capacitance (Note 1) Typical Thermal Resistance (Note 2) Operating Junction Temperature Range Storage Temperature Range BY296 100 70 100 BY297 200 140 200 BY298 400 280 400 BY299 800 560 800 UNITS Volts Volts Volts I(AV) 2.0 Amp IFSM 70 Amps VF 1.3 5.0 200 500 25 40 (-55 to +150) (-55 to +150) Volts IR trr CJ RθJA TJ TSTG Notes: 1.Measured at 1.0MHz and Applied Reverse Voltage of 4.0Volits. 2 Thermal Resistance from junction to Ambient at .375”(9.5mm)lead length, P.C.board mounted. 3.Reverse Recovery Test Conditions:If=10mA,Ir=10mA,Irr=1A Web Site: www.hkmic.com µA ns pF ℃/W ℃ ℃ FAST RECOVER RECTIFIER VOLTAGE RANGE CURRENT BY296 THRU BY299 100 to 800 Volts 2 .0Ampere RATING AND CHRACTERISTIC CURVES BY296 THRU BY299 FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE 70 PEAK FORWARD SURGE 60 1.0 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375"(9.5mm)Lead Length 0 0 25 50 100 75 150 125 8.3ms Single Half Sine-Wave (JEDEC Method) Tj=Tjmax 50 CURRENT, (A) 2.0 (A) AVERAGE FORWARD CURRENT, 3.0 40 30 20 10 0 175 1 2 AMBIENT TEMPERATURE, (° C) 4 8 6 10 20 40 60 80 100 NUMBER OF CYCLES AT 60 Hz FIG.4-TYPICAL REVERSE CHARACTERISTICS FIG.3-TYPICAL INSTANTANEOUS 20 10 INSTANTANEOUS REVERSE CURRENT, (uA) 10 (A) INSTANTANEOUS FORWARD CURRENT, FORWARD CHARACTERISTICS 1.0 0.1 Tj =25° C Pulse Width=300us 1% Duty Cycle 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 Tj =100° C 1.0 0.1 Tj =25° C 0.01 0 INSTANTANEOUS FORWARD VOLTAGE,(V) 20 60 40 80 120 100 140 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FIG.5-TYPICAL JUNCTION CAPACITANCE FIG.6-TEST CIRCUIT DIAGRAM AND REVERSE REXOVERY TIME CHARACTERISTIC JUNCTION CAPACITANCE,(pF) 100 +0.5A 50Ω NONINDUCTIVE 10Ω NONINDUCTIVE (-) (+) 25 Vdc (approx) (-) 10 D.U.T 1Ω NON INDUCTIVE PULSE GENERATIOR (NOTE 2) 0 0.25A OSCILLOSCOPE (NOTE 1) -1.0A TJ=25° C F=1MHz NOTE: 1.Rise Time =7ns max.Input Impedance=1megohm.22pF 2.Rise time=10ns max.Source Impedance=50 ohms Vsig=50mVp-p 1 0.1 1.0 10 100 REVERSE VOLTAGE,(V) Web Site: www.hkmic.com SET TIME BASE FOR 50 /100NS /cm