lhrf9ug3993-pf.pdf

LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
DUAL COLOR TYPE LED LAMPS
Pb
Lead-Free Parts
LHRF9UG3993-PF
DATA SHEET
DOC. NO :
QW0905-LHRF9UG3993-PF
REV.
:
A
DATE
: 24 - May - 2010
發行
立碁電子
DCC
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Page 1/6
PART NO. LHRF9UG3993-PF
Package Dimensions
8.0 9.1
9.0
11 12.05±0.5
15.1±0.5
1.5MAX
9UG HRF
□0.5
TYP
18.0MIN
1
2
1
3
2
1.ANODE GREEN
2.COMMON CATHODE
3.ANODE RED
2.0MIN
2.0MIN
2.54TYP
2.54TYP
Note : 1.All dimension are in millimeter tolerance is ±0.25mm unless otherwise noted.
2.Specifications are subject to change without notice.
Directivity Radiation
0°
-30°
30°
60°
-60°
100% 75% 50%
3
25%
0
25% 50% 75% 100%
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
PART NO. LHRF9UG3993-PF
Page 2/6
Absolute Maximum Ratings at Ta=25 ℃
Absolute Maximum Ratings
Symbol
Parameter
UNIT
HRF
9UG
Forward Current
IF
30
30
mA
Peak Forward Current
Duty 1/10@10KHz
IFP
90
60
mA
Power Dissipation
PD
75
75
mW
Reverse Current @5V
Ir
10
10
μA
Electrostatic Discharge
ESD
2000
V
Operating Temperature
Topr
-40 ~ +85
℃
Storage Temperature
Tstg
-40 ~ +100
℃
Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic
* glove
is recommended when handing these LED. All devices, equipment and machinery must be properly
grounded.
Typical Electrical & Optical Characteristics (Ta=25 ℃)
PART NO
COLOR
MATERIAL
Emitted
AlGaInP
Red
AlGaInP
Green
Forward
Dominant Spectral
voltage
wave halfwidth
length
△λ nm @20mA(V)
λDnm
Luminous
intensity
@20mA(mcd)
Viewing
angle
2θ 1/2
(deg)
Min. Max. Min. Typ.
Lens
630
20
1.5
2.4
300
450
58
574
20
1.7
2.6
90
160
58
Water Clear
LHRF9UG3993-PF
Note : 1.The forward voltage data did not including ±0.1V testing tolerance.
2. The luminous intensity data did not including ±15% testing tolerance.
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
PART NO. LHRF9UG3993-PF
Page 3/6
Typical Electro-Optical Characteristics Curve
HRF CHIP
Fig.1 Forward current vs. Forward Voltage
Fig.2 Relative Intensity vs. Forward Current
3.5
Relative Intensity
Normalize @20mA
Forward Current(mA)
1000
100
10
1.0
0.1
3.0
2.5
2.0
1.5
1.0
0.5
0
1.0
1.5
2.0
2.5
3.0
1.0
10
Fig.3 Forward Voltage vs. Temperature
Fig.4 Relative Intensity vs. Temperature
3.0
Relative Intensity@20mA
Normalize@25 ℃
1.2
Forward Voltage@20mA
Normalize @25℃
1000
Forward Current(mA)
Forward Voltage(V)
1.1
1.0
0.9
0.8
-40
-20
-0
20
40
60
80
100
Ambient Temperature( ℃)
Fig.5 Relative Intensity vs. Wavelength
Relative Intensity@20mA
100
1.0
0.5
0
550
600
650
Wavelength (nm)
700
2.5
2.0
1.5
1.0
0.5
0
-40
-20
0
20
40
60
80
Ambient Temperature( ℃)
100
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
PART NO. LHRF9UG3993-PF
Page 4/6
Typical Electro-Optical Characteristics Curve
9UG CHIP
Fig.1 Forward current vs. Forward Voltage
Fig.2 Relative Intensity vs. Forward Current
3.0
Relative Intensity
Normalize @20mA
Forward Current(mA)
1000
100
10
1.0
0.1
2.5
2.0
1.5
1.0
0.5
0
1.0
2.0
3.0
4.0
5.0
1.0
10
1.2
1.1
1.0
0.9
0.8
0
20
40
60
80
100
Fig.5 Relative Intensity vs. Wavelength
1.0
0.5
0
500
550
600
Wavelength (nm)
3.0
2.5
2.0
1.5
1.0
0.5
0
-40
-20
0
20
40
60
80
Ambient Temperature( ℃)
Ambient Temperature( ℃)
Relative Intensity @20mA
Fig.4 Relative Intensity vs. Temperature
Relative Intensity @20mA
Normalize @25℃
Forward Voltage@20mA
Normaliz @25℃
Fig.3 Forward Voltage vs. Temperature
-20
1000
Forward Current(mA)
Forward Voltage(V)
-40
100
650
100
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Page 5/6
PART NO. LHRF9UG3993-PF
Soldering Condition(Pb-Free)
1.Iron:
Soldering Iron:30W Max
Temperature 350° C Max
Soldering Time:3 Seconds Max(One time only)
Distance:2mm Min(From solder joint to body)
2.Wave Soldering Profile
Dip Soldering
Preheat: 120° C Max
Preheat time: 60seconds Max
Ramp-up
2°C/sec(max)
Ramp-Down:-5° C/sec(max)
Solder Bath:260°C Max
Dipping Time:3 seconds Max
Distance:2mm Min(From solder joint to body)
Temp(° C)
260° C3sec Max
260°
5° /sec
max
120°
25°
0° 0
2° /sec
max
Preheat
50
100
60 Seconds Max
Note: 1.Wave solder should not be made more than one time.
2.You can just only select one of the soldering conditions as above.
150
Time(sec)
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Page 6/6
PART NO. LHRF9UG3993-PF
Reliability Test:
Test Item
Test Condition
Description
Reference
Standard
Operating Life Test
1.Under Room Temperature
2.If=20mA
3.t=1000 hrs (-24hrs, +72hrs)
This test is conducted for the purpose
of detemining the resistance of a part
in electrical and themal stressed.
MIL-STD-750: 1026
MIL-STD-883: 1005
JIS C 7021: B-1
High Temperature
Storage Test
1.Ta=105 ℃±5 ℃
2.t=1000 hrs (-24hrs, +72hrs)
The purpose of this is the resistance of
the device which is laid under condition
of high temperature for hours.
MIL-STD-883:1008
JIS C 7021: B-10
Low Temperature
Storage Test
1.Ta=-40 ℃±5℃
2.t=1000 hrs (-24hrs, +72hrs)
The purpose of this is the resistance
of the device which is laid under
condition of low temperature for hours.
High Temperature
High Humidity Test
1.Ta=65 ℃±5℃
2.RH=90 %~95 %
3.t=240hrs ±2hrs
The purpose of this test is the resistance
of the device under tropical for hours.
1.Ta=105 ℃±5 ℃&-40 ℃±5℃
(10min) (10min)
2.total 10 cycles
The purpose of this is the resistance of
the device to sudden extreme changes
in high and low temperature.
MIL-STD-202: 107D
MIL-STD-750: 1051
MIL-STD-883: 1011
Solder Resistance
Test
1.T.Sol=260 ℃±5℃
2.Dwell time= 10 ±1sec.
This test intended to determine the
thermal characteristic resistance
of the device to sudden exposures
at extreme changes in temperature
when soldering the lead wire.
MIL-STD-202: 210A
MIL-STD-750: 2031
JIS C 7021: A-1
Solderability Test
1.T.Sol=230 ℃±5℃
2.Dwell time=5 ±1sec
This test intended to see soldering well
performed or not.
MIL-STD-202: 208D
MIL-STD-750: 2026
MIL-STD-883: 2003
JIS C 7021: A-2
Thermal Shock Test
JIS C 7021: B-12
MIL-STD-202:103B
JIS C 7021: B-11