SCHOTTKY BARRIER RECTIFIER SR602 THRU SR610 VOLTAGE RANGE 50 to 100 Volts CURRENT 6.0 Ampere FEATURES • • • • • R-6 Fast switching speed Low forward voltage Low power high efficiency High surge capability High temperature soldering guaranteed 250℃/10 seconds,0.373”(9.5mm)lead length .052(1.3) .048(1.2) 1.0(25.4) MIN. DIA. .360(9.1) .340(8.6) MECHANICAL DATA • • • • • • .360(9.1) DIA. .340(8.6) Case: Transfer molded plastic Epoxy: UL94V-0 rate flame retardant Lead: Plated axial lead, solderable per MIL-STD-202E method 208C Polarity: Color band denotes cathode end Mounting position: Any Weight: 0.07ounce, 2.0 gram 1.0(25.4) MIN. Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% SYMBOLS SR602 SR603 Maximum Repetitive Peak Reverse Voltage VRRM 20 30 Maximum RMS Voltage VRMS 14 21 Maximum DC Blocking Voltage VDC 20 30 Maximum Average Forward Rectified Current 0.375”(9.5)Lead length,(Note 1)See Fig..1 TL = 60℃(SR602-604) TL = 85℃(SR605-610) Peak Forward Surge Current 8.3mS single half sine wave superimposed on rated load (JEDEC method) Maximum DC Reverse Current at rated DC blocking Voltage (Note 1) TA = 25℃ SR606 60 42 60 SR608 80 56 80 SR610 100 70 100 UNIT Volts Volts Volts 6.0 Amps IFSM 150 Amps 0.57 IR TA = 100℃ SR605 50 35 50 I(AV) VF Maximum Instantaneous Forward Voltage @ 6.0A SR604 40 28 40 0.70 1.0 50 0.85 450 350 Volts µA Typical Junction Capacitance CJ (Measured at 1.0MHz and applied reverse voltage of 4.0V) Typical Thermal Resistance Operating Junction Temperature Range Storage Temperature Range 550 RθJL TJ TSTG Notes: 1. Pulse test:300μs pulse width,1% duty cycle Web Site: www.hkmic.com 10 (-55 to +150) (-55 to +150) pF ℃/W ℃ ℃ SCHOTTKY BARRIER RECTIFIER SR602 THRU SR610 VOLTAGE RANGE 20 to 100 Volts CURRENT 6.0 Amperes RATING AND CHRACTERISTIC CURVES SR602 THRU SR610 FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 5.0 SR 4.0 R5 5-S (A) 50 3.0 10 R5 10 Inductive or Resistive Load 2.0 5-S Single Phase Half Wave 60Hz 0.375″(9.5mm) Lead Length 1.0 150 CURRENT, (A) PEAK FORWARD SURGE 6.0 50 SR AVERAGE FORWARD CURRENT, FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE 8.3ms Single Half Sine-Wave (JEDEC Method) T= j Tjmax 100 50 1 Cycle 0 25 0 75 85 50 60 100 125 175 150 0 1 AMBIENT TEMPERATURE, (° C) 2 4 6 8 10 20 40 60 100 NUMBER OF CYCLES AT 60 Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.4-TYPICAL REVERSE CHARACTERISTICS 100 INSTANTANEOUS REVERSE CURRENT, (mA) SR505-SR510 10 (A) INSTANTANEOUS FORWARD CURRENT, SR502-SR504 1.0 T J =25° C PULSE WIDTH=300μs DUTY CYCLE1% 0.1 SR502-SR504 SR505-SR510 1.0 TJ =125° C 0.1 TJ=75° C 0.01 TJ =25° C 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 0.001 INSTANTANEOUS FORWARD VOLTAGE,(V) 0 20 40 60 80 100 120 PERCENT OF RATED PEAK FIG.5-TYPICAL JUNCTION CAPACITANCE REVERSE VOLTAGE,(%) JUNCTION CAPACITANCE,(pF) 10000 T J =25° C f=1MHz Vsig=50mV 1000 SR502-SR504 SR505-SR510 100 0.1 1.0 10 100 REVERSE VOLTAGE,(V) Web Site: www.hkmic.com 140