Datasheet

SSF2616E
DESCRIPTION
The SSF2616E uses advanced trench technology to
provide excellent RDS(ON), low gate charge and operation
with gate voltages as low as 2.5V.
GENERAL FEATURES
● VDS = 20V,ID = 7A
RDS(ON) < 30mΩ @ VGS=2.5V
RDS(ON) < 26mΩ @ VGS=3.1V
RDS(ON) < 23mΩ @ VGS=4V
RDS(ON) < 22mΩ @ VGS=4.5V
Schematic diagram
ESD Rating:2000V HBM
● High Power and current handing capability
● Lead free product is acquired
● Surface Mount Package
Marking and pin Assignment
Application
●Battery protection
●Load switch
●Power management
SOP-8 Top View
PACKAGE MARKING AND ORDERING INFORMATION
Device Marking
Device
Device Package
Reel Size
Tape width
Quantity
SSF2616E
SSF2616E
SOP-8
Ø330mm
12mm
2500 units
ABSOLUTE MAXIMUM RATINGS(TA=25℃unless otherwise noted)
Parameter
Symbol
Limit
Unit
Drain-Source Voltage
VDS
20
V
Gate-Source Voltage
VGS
±12
V
ID(25℃)
7
A
ID(70℃)
5
A
IDM
25
A
PD
1.5
W
TJ,TSTG
-55 To 150
℃
RθJA
83
℃/W
Drain Current-Continuous@ Current-Pulsed (Note 1)
Maximum Power Dissipation
Operating Junction and Storage Temperature Range
THERMAL CHARACTERISTICS
Thermal Resistance,Junction-to-Ambient (Note 2)
ELECTRICAL CHARACTERISTICS (TA=25℃unless otherwise noted)
Parameter
Symbol
Condition
Min
Typ
Max
Unit
OFF CHARACTERISTICS
©Silikron Semiconductor CO.,LTD.
1
http://www.silikron.com
v1.1
SSF2616E
Drain-Source Breakdown Voltage
BVDSS
VGS=0V ID=250μA
20
V
Zero Gate Voltage Drain Current
IDSS
VDS=20V,VGS=0V
1
μA
Gate-Body Leakage Current
IGSS
VGS=±4.5V,VDS=0V
±200
nA
VGS=±10V,VDS=0V
±10
uA
0.75
1.2
V
VGS=4.5V, ID=6.5A
16.5
22
mΩ
VGS=4V, ID=6A
17
23
mΩ
VGS=3.1V, ID=5.5A
19
26
mΩ
VGS=2.5V, ID=5.5A
22
30
mΩ
VDS=10V,ID=6.5A
6.6
S
600
PF
330
PF
PF
ON CHARACTERISTICS (Note 3)
Gate Threshold Voltage
Drain-Source On-State Resistance
Forward Transconductance
VGS(th)
VDS=VGS,ID=250μA
RDS(ON)
gFS
0.6
DYNAMIC CHARACTERISTICS (Note4)
Input Capacitance
Clss
VDS=8V,VGS=0V,
F=1.0MHz
Output Capacitance
Coss
Reverse Transfer Capacitance
Crss
140
Turn-on Delay Time
td(on)
10
20
nS
Turn-on Rise Time
tr
11
25
nS
35
70
nS
30
60
nS
10
15
nC
SWITCHING CHARACTERISTICS (Note 4)
Turn-Off Delay Time
VDD=10V,ID=1A
VGS=4.5V,RGEN=6Ω
td(off)
Turn-Off Fall Time
tf
Total Gate Charge
Qg
Gate-Source Charge
Qgs
Gate-Drain Charge
Qgd
VDS=10V,ID=7A,
VGS=4.5V
2.3
nC
3
nC
DRAIN-SOURCE DIODE CHARACTERISTICS
Diode Forward Voltage (Note 3)
VSD
VGS=0V,IS=1.5A
0.84
1.2
V
NOTES:
1. Repetitive Rating: Pulse width limited by maximum junction temperature.
2. Surface Mounted on 1in2 FR4 Board, t ≤ 10 sec.
3. Pulse Test: Pulse Width ≤ 300μs, Duty Cycle ≤ 2%.
4. Guaranteed by design, not subject to production testing.
©Silikron Semiconductor CO.,LTD.
2
http://www.silikron.com
v1.1
SSF2616E
TYPICAL ELECTRICAL AND THERMAL CHARACTERISTICS
Vdd
Vgs
Rgen
D
VOUT
Vout
toff
tf
td(off)
90%
Rl
Vin
ton
tr
td(on)
90%
INVERTED
10%
10%
G
90%
VIN
S
50%
50%
10%
PULSE WIDTH
Figure 2:Switching Waveforms
PD Power(W)
ID- Drain Current (A)
Figure 1:Switching Test Circuit
TJ-Junction Temperature(℃)
TJ-Junction Temperature(℃)
Figure 3 Power Dissipation
ID- Drain Current (A)
Rdson On-Resistance(mΩ)
Figure 4 Drain Current
ID- Drain Current (A)
Vds Drain-Source Voltage (V)
Figure 5 Output CHARACTERISTICS
©Silikron Semiconductor CO.,LTD.
Figure 6 Drain-Source On-Resistance
3
http://www.silikron.com
v1.1
ID- Drain Current (A)
Normalized On-Resistance
SSF2616E
TJ-Junction Temperature(℃)
Figure 7 Transfer Characteristics
Figure 8 Drain-Source On-Resistance
C Capacitance (pF)
Rdson On-Resistance(mΩ)
Vgs Gate-Source Voltage (V)
Vds Drain-Source Voltage (V)
Figure 9 Rdson vs Vgs
Figure 10 Capacitance vs Vds
Is- Reverse Drain Current (A)
Vgs Gate-Source Voltage (V)
Vgs Gate-Source Voltage (V)
Vsd Source-Drain Voltage (V)
Qg Gate Charge (nC)
Figure 12 Source- Drain Diode Forward
Figure 11 Gate Charge
©Silikron Semiconductor CO.,LTD.
4
http://www.silikron.com
v1.1
ID- Drain Current (A)
SSF2616E
Vds Drain-Source Voltage (V)
Safe Operation Area
r(t),Normalized Effective
Transient Thermal Impedance
Figure 13
Square Wave Pluse Duration(sec)
Figure 14 Normalized Maximum Transient Thermal Impedance
©Silikron Semiconductor CO.,LTD.
5
http://www.silikron.com
v1.1
SSF2616E
SOP-8 PACKAGE INFORMATION
NOTES:
1. Dimensions are inclusive of plating
2. Package body sizes exclude mold flash and gate burrs. Mold flash at the non-lead sides should be less than 6 mils.
3. Dimension L is measured in gauge plane.
4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exa
©Silikron Semiconductor CO.,LTD.
6
http://www.silikron.com
v1.1
SSF2616E
ATTENTION:
■
■
■
■
■
■
■
■
■
Any and all Silikron products described or contained herein do not have specifications that can handle applications that require
extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can
be reasonably expected to result in serious physical and/or material damage. Consult with your Silikron
representative nearest you before using any Silikron products described or contained herein in such applications.
Silikron assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in
products specifications of any and all Silikron products described or contained herein.
Specifications of any and all Silikron products described or contained herein stipulate the performance, characteristics, and
functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and
functions of the described products as mounted in the customer’s products or equipment. To verify symptoms and states that
cannot be evaluated in an independent device, the customer should always evaluate and test devices
mounted in the customer’s products or equipment.
Silikron Semiconductor CO.,LTD. strives to supply high-quality high-reliability products. However, any and all semiconductor
products fail with some probability. It is possible that these probabilistic failures could give rise to
accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to
other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such
measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and
structural design.
In the event that any or all Silikron products(including technical data, services) described or contained herein are controlled under
any of applicable local export control laws and regulations, such products must not be exported without obtaining the export
license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including
photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of
Silikron Semiconductor CO.,LTD.
Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume
production. Silikron believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use
or any infringements of intellectual property rights or other rights of third parties.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the Silikron product
that you intend to use.
This catalog provides information as of Dec, 2008. Specifications and information herein are subject to change without notice.
©Silikron Semiconductor CO.,LTD.
7
http://www.silikron.com
v1.1