2W SMD DC-DC Converter P2JS-Series ● ● ● ● ● ● SMD 8 lead package Up to 3000 VDC isolation MTBF > 3.5 Mio. h at 25 °C -40...105 °C operating temperature range Efficiency up to 86 % Continuous short circuit protection Model guide Type P2JS053R3S P2JS0505S P2JS0509S P2JS0512S P2JS0515S P2JS0524S P2JS123R3S P2JS1205S P2JS1209S P2JS1212S P2JS1215S P2JS1224S P2JS1505S P2JS1512S P2JS1515S P2JS1524S P2JS243R3S P2JS2405S P2JS2409S P2JS2412S P2JS2415S P2JS2424S Input voltage range [VDC] Full load [mA] typ. No load [mA] typ. [VDC] min. [mA] max. [mA] Output ripple & noise (see note 4) [mVp-p] typ. 4.5..5.5 4.5..5.5 4.5..5.5 4.5..5.5 4.5..5.5 4.5..5.5 10.8..13.2 10.8..13.2 10.8..13.2 10.8..13.2 10.8..13.2 10.8..13.2 13.5..16.5 13.5..16.5 13.5..16.5 13.5..16.5 21.6..26.4 21.6..26.4 21.6..26.4 21.6..26.4 21.6..26.4 21.6..26.4 506 506 506 506 506 506 212 212 212 212 212 212 169 169 169 169 105 105 105 105 105 105 30 30 30 30 30 30 25 25 25 25 25 25 18 18 18 18 15 15 15 15 15 15 3.3 5.0 9.0 12.0 15.0 24.0 3.3 5.0 9.0 12.0 15.0 24.0 5.0 12.0 15.0 24.0 3.3 5.0 9.0 12.0 15.0 24.0 40 40 22 17 13 8 40 40 22 17 13 8 40 17 13 8 40 40 22 17 13 8 400 400 220 167 130 83 400 400 220 167 130 83 400 167 130 83 400 400 220 167 130 83 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 Input current Output voltage Output current Efficiency typ. @ full load Maximum capacitive load [%] 78 79 82 82 83 84 78 79 82 82 83 84 79 82 83 84 78 79 82 82 83 86 [µF] 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 Specifications Input Voltage range Filter Reflected ripple current Input / output: Isolation voltage tested for 60 sec. @ leakage current < 1mA Isolation resistance @ 500 VDC Capacitance Output Output voltage drift @ 3.3V Vout models Output voltage drift @ all other models Output voltage tolerance Output voltage deviation at load change Temperature coefficient Short circuit protection General Switching frequency Reliability, MTBF (MIL-HDBK-217 @ 25 °C) Physical Package material Weight ± 10 % of nominal Capacitors 15 mAp-p, typ. 3 kVDC 109 Ω, min. 20 pF, typ. ± 1.5 % @ 1% Vin change ± 1.2 % @ 1% Vin change ± 5 % @ 70 % load, See output voltage tolerance diagram See output voltage tolerance diagram 0.03 % / °C, max., at full load Continuous, auto recovery 100 kHz, typ. 300 kHz, max. 3.5 Mio. hours Environmental Operating temperature (ambient) Storage temperature Derating Cooling Case temperature rise at full load Humidity EMC CISPR22 / EN55022 class B (Recommended circuit refer to Fig. 1) CISPR22 / EN55022 class B (Recommended circuit refer to Fig. 1) IEC/EN61000-4-2 contact ± 8 kV perf. criteria B CE EMI RE EMS -40 °C to +105 °C -55 °C to +125 °C See derating curve Free air convection 25 °C Up to 95 %, non condensing ESD Absolute maximum ratings Vin 5 V types Vin 12 V types Vin 15 V types Vin 24 V types Manual soldering lead temperature Soldering temperature Moisture sensitivity level (MSL) -0.7 ~ 9 VDC, max. 1 s -0.7 ~ 18 VDC, max. 1 s -0.7 ~ 21 VDC, max. 1 s -0.7 ~ 30 VDC, max. 1 s 300 °C max. 10 s max., 1.5 mm distance from body 217 °C for 60 s max., 245 °C peak IPC/JEDEC J-STD-020D.1 Epoxy resin (UL94-V0) 1.5 g, typ. Page 1 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 2W SMD DC-DC Converter P2JS-Series Input reflected ripple current measure circuit oscilloscope current probe + Vin 4.7µH Measure point 220 µF ESR <1 Ω at 100 kHz Load - Vin Figure 1 Recommended EMC / EMI circuit for Class B standard + Vin 6.8µH + Vout 4.7µF Cout - Vin Load - Vout Y2 470 pF only P2JS2424S Page 2 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 2W SMD DC-DC Converter P2JS-Series Note: 1. Operation under minimum load will not damage the converter, however they may not meet all specifications. 2. Max. capacitive load is tested at nominal input voltage and full load. 3. Unless otherwise noted, all specifications are measured at Ta 25 °C, humidity <75 %, nominal input voltage and rated output load. 4. Ripple and noise tested with „parallel cable“.method. 5. P2JS-series is not usable for IGBT driver applications. Page 3 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 2W SMD DC-DC Converter P2JS-Series Application notes 1) Requirement on output load To ensure this module can operate efficiently and reliably during operation, the minimum output load must be higher than 10 % of the full load. If the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load, or use our company’s products with a lower rated output power. Operation with smaller load than minimum load will not damage the converter. However, they may not meet all specification listed, and that will reduce the life time of product. 2) Overload Protection Under normal operating conditions, the output circuit of these products has no protection against overload. The simplest method is to connect a self recovery fuse in series at the input end or add a circuit breaker to the circuit. 3) Output Voltage Regulation and Over-voltage Protection Circuit The simplest device for output voltage regulation, over voltage and over current protection is a linear voltage regulator with overheat protection that is connected to the input or output end in series. 4) Recommended circuit If you want to further decrease the input / output ripple, filter capacitors may be connected to the input and output ends of the DC/DC converter, see (Figure 3). It should also be noted that the capacitance of the capacitor must be proper. If the capacitance is too large, a startup problem might arise. It should also be noted that the capacitance of the capacitor must be proper. If the capacitance is too large, a startup problem might arise. For an safe and reliable operation of every model, the recommended capacitance of the capacitor refer to table below. Figure 3 + Vin + Vout Cin - Vin Cout - Vout Vin P2JS05xxS P2JS12xxS P2JS15xxS P2JS24xxS Cin 4.7 µF 2.2 µF 2.2 µF 1 µF Vout P2JSxx3R3S P2JSxx05S P2JSxx09S P2JSxx12S P2JSxx15S P2JSxx24S Cout 10 µF 10 µF 4.7 µF 2.2 µF 1 µF 0.47 µF It’s not recommended to connect any external capacitor in the application field with less than 0.5 W output power! 5) The input and the output of the product are recommended to be connected to ceramic capacitor or electrolytic capacitor. Using tantalum capacitor may cause risk of failure 6) Not for parallel connection or plug and play (hot swap) application! Package dimensions Lead 1 2 3 4 5 6 7 8 - Vinput + Vinput No lead - Voutput + Voutput No lead No lead Not connected Notes: All dimensions are in mm General tolerances ±0.25 mm Pin tolerances ±0.1 mm Page 4 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 2W SMD DC-DC Converter P2JS-Series PHI-CON is a trademark of HY-LINE Holding GmbH. Only for professional use by professionals! Not for resale or distribution to the general public in any way! Read the instructions carefully before using! Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Rev: 11.14 f Page 5 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected]