NCP1402 D

NCP1402
200 mA, PFM Step-Up
Micropower Switching
Regulator
Features
•
•
•
•
•
•
•
•
•
•
Extremely Low Startup Voltage of 0.8 V
Operation Down to Less than 0.3 V
High Efficiency 85% (Vin = 2.0 V, VOUT = 3.0 V, 70 mA)
Low Operating Current of 30 mA (VOUT = 1.9 V)
Output Voltage Accuracy ±2.5%
Low Converter Ripple with Typical 30 mV
Only Three External Components Are Required
Chip Enable Power Down Capability for Extended Battery Life
Micro Miniature Thin SOT−23−5 Packages
These Devices are Pb−Free and are RoHS Compliant
http://onsemi.com
SOT23−5
(TSOP−5, SC59−5)
SN SUFFIX
CASE 483
PIN CONNECTIONS AND
MARKING DIAGRAM
CE
1
OUT
2
NC
3
xxxAYW G
G
The NCP1402 series are monolithic micropower step−up DC to DC
converter that are specially designed for powering portable equipment
from one or two cell battery packs.These devices are designed to
startup with a cell voltage of 0.8 V and operate down to less than 0.3 V.
With only three external components, this series allow a simple means
to implement highly efficient converters that are capable of up to
200 mA of output current at Vin = 2.0 V, VOUT = 3.0 V.
Each device consists of an on−chip PFM (Pulse Frequency
Modulation) oscillator, PFM controller, PFM comparator, soft−start,
voltage reference, feedback resistors, driver, and power MOSFET
switch with current limit protection. Additionally, a chip enable
feature is provided to power down the converter for extended battery
life.
The NCP1402 device series are available in the Thin SOT−23−5
package with five standard regulated output voltages. Additional
voltages that range from 1.8 V to 5.0 V in 100 mV steps can be
manufactured.
5
LX
4
GND
(Top View)
xxx
A
Y
W
G
= Marking
= Assembly Location
= Year
= Work Week
= Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information in the ordering
information section on page 17 of this data sheet.
Typical Applications
•
•
•
•
•
•
•
•
Cellular Telephones
Pagers
Personal Digital Assistants (PDA)
Electronic Games
Portable Audio (MP3)
Camcorders
Digital Cameras
Handheld Instruments
© Semiconductor Components Industries, LLC, 2014
July, 2014 − Rev. 10
1
Publication Order Number:
NCP1402/D
NCP1402
Vin
VOUT
LX
CE
1
OUT NCP1402
2
NC
5
GND
4
3
Figure 1. Typical Step−Up Converter Application
OUT
2
LX
5
VLX LIMITER
DRIVER
−
+
NC
3
PFM
COMPARATOR
POWER
SWITCH
PFM
CONTROLLER
VOLTAGE
REFERENCE
SOFT−START
PFM
OSCILLATOR
GND
4
1 CE
Figure 2. Representative Block Diagram
PIN FUNCTION DESCRIPTIONS
Pin #
Symbol
1
CE
2
OUT
3
NC
4
GND
5
LX
Pin Description
Chip Enable pin
(1) The chip is enabled if a voltage which is equal to or greater than 0.9 V is applied
(2) The chip is disabled if a voltage which is less than 0.3 V is applied
(3) The chip will be enabled if it is left floating
Output voltage monitor pin, also the power supply pin of the device
No internal connection to this pin
Ground pin
External inductor connection pin to power switch drain
http://onsemi.com
2
NCP1402
ABSOLUTE MAXIMUM RATINGS
Rating
Symbol
Value
Unit
VOUT
6.0
V
Input/Output Pins
LX (Pin 5)
LX Peak Sink Current
VLX
ILX
−0.3 to 6.0
400
V
mA
CE (Pin 1)
Input Voltage Range
Input Current Range
VCE
ICE
−0.3 to 6.0
−150 to 150
V
mA
Thermal Resistance, Junction−to−Air
RqJA
250
°C/W
Operating Ambient Temperature Range (Note 2)
TA
−40 to +85
°C
Operating Junction Temperature Range
TJ
−40 to +125
°C
Storage Temperature Range
Tstg
−55 to +150
°C
Power Supply Voltage (Pin 2)
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
NOTES:
1. This device series contains ESD protection and exceeds the following tests:
Human Body Model (HBM) ±2.0 kV per JEDEC standard: JESD22−A114.
Machine Model (MM) ±150 V per JEDEC standard: JESD22−A115.
2. The maximum package power dissipation limit must not be exceeded.
TJ(max) * TA
PD +
RqJA
3. Latchup Current Maximum Rating: ±150 mA per JEDEC standard: JESD78.
4. Moisture Sensitivity Level: MSL 1 per IPC/JEDEC standard: J−STD−020A.
http://onsemi.com
3
NCP1402
ELECTRICAL CHARACTERISTICS (For all values TA = 25°C, unless otherwise noted.)
Symbol
Min
Switch On Time (current limit not asserted)
ton
Switch Minimum Off Time
toff
Characteristic
Typ
Max
Unit
3.6
5.5
7.6
ms
1.0
1.45
1.9
ms
DMAX
70
78
85
%
OSCILLATOR
Maximum Duty Cycle
Minimum Startup Voltage (IO = 0 mA)
Vstart
−
0.8
0.95
V
DVstart
−
−1.6
−
mV/°C
Vhold
0.3
−
−
V
tSS
0.3
2.0
−
ms
Internal Switching N−Channel FET Drain Voltage
VLX
−
−
6.0
V
LX Pin On−State Sink Current (VLX = 0.4 V)
Device Suffix:
19T1
27T1
30T1
33T1
40T1
50T1
ILX
Minimum Startup Voltage Temperature Coefficient (TA = −40°C to 85°C)
Minimum Operation Hold Voltage (IO = 0 mA)
Soft−Start Time (VOUT u 0.8 V)
LX (PIN 5)
mA
110
130
130
130
130
130
145
180
190
200
210
215
−
−
−
−
−
−
VLXLIM
0.45
0.65
0.9
V
ILKG
−
0.5
1.0
mA
CE Input Voltage (VOUT = VSET x 0.96)
High State, Device Enabled
Low State, Device Disabled
VCE(high)
VCE(low)
0.9
−
−
−
−
0.3
CE Input Current (Note 6)
High State, Device Enabled (VOUT = VCE = 6.0 V)
Low State, Device Disabled (VOUT = 6.0 V, VCE = 0 V)
ICE(high)
ICE(low)
−0.5
−0.5
0
0.15
0.5
0.5
Voltage Limit
Off−State Leakage Current (VLX = 6.0 V, TA = −40°C to 85°C)
CE (PIN 1)
V
mA
TOTAL DEVICE
Output Voltage
Device Suffix:
19T1
27T1
30T1
33T1
40T1
50T1
VOUT
V
1.853
2.632
2.925
3.218
3.900
4.875
1.9
2.7
3.0
3.3
4.0
5.0
1.948
2.768
3.075
3.383
4.100
5.125
DVOUT
Output Voltage Temperature Coefficient (TA = −40°C to +85°C)
Device Suffix:
19T1
27T1
30T1
33T1
40T1
50T1
ppm/°C
−
−
−
−
−
−
150
150
150
150
150
150
−
−
−
−
−
−
Operating Current 2 (VOUT = VCE = VSET +0.5 V, Note 5)
IDD2
−
13
15
mA
Off−State Current (VOUT = 5.0 V, VCE = 0 V, TA = −40°C to +85°C, Note 6)
IOFF
−
0.6
1.0
mA
Operating Current 1 (VOUT = VCE = VSET x 0.96)
Device Suffix:
19T1
27T1
30T1
33T1
40T1
50T1
IDD1
mA
−
−
−
−
−
−
30
39
42
45
55
70
50
60
60
60
100
100
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
5. VSET means setting of output voltage.
6. CE pin is integrated with an internal 10 MW pullup resistor.
http://onsemi.com
4
NCP1402
4.0
NCP1402SN19T1
L = 47 mH
TA = 25°C
2.0
VOUT, OUTPUT VOLTAGE (V)
VOUT, OUTPUT VOLTAGE (V)
2.1
1.9
Vin = 1.5 V
Vin = 0.9 V
1.8
Vin = 1.2 V
1.7
1.6
0
20
40
60
80
Vin = 2.5 V
3.0
Vin = 0.9 V
2.5
Vin = 1.2 V
2.0
0
20
40
60
80
100 120 140 160 180 200
IO, OUTPUT CURRENT (mA)
Figure 3. NCP1402SN19T1 Output Voltage vs.
Output Current
Figure 4. NCP1402SN30T1 Output Voltage vs.
Output Current
100
Vin = 4.0 V
80
Vin = 1.5 V
Vin = 1.2 V
4.0
EFFICIENCY (%)
5.0
Vin = 2.0 V
Vin = 3.0 V
Vin = 0.9 V
3.0
NCP1402SN50T1
L = 47 mH
TA = 25°C
2.0
Vin = 1.5 V
60
Vin = 0.9 V
Vin = 1.2 V
40
NCP1402SN19T1
L = 47 mH
TA = 25°C
20
1.0
0
0
20
40
60
80
100 120 140 160 180 200
0
20
40
60
80
100 120 140 160 180 200
IO, OUTPUT CURRENT (mA)
IO, OUTPUT CURRENT (mA)
Figure 5. NCP1402SN50T1 Output Voltage vs.
Output Current
Figure 6. NCP1402SN19T1 Efficiency vs.
Output Current
100
100
Vin = 4.0 V
Vin = 2.5 V
80
80
Vin = 2.0 V
EFFICIENCY (%)
EFFICIENCY (%)
Vin = 2.0 V
Vin = 1.5 V
IO, OUTPUT CURRENT (mA)
6.0
VOUT, OUTPUT VOLTAGE (V)
3.5
1.5
100 120 140 160 180 200
NCP1402SN30T1
L = 47 mH
TA = 25°C
60
Vin = 0.9 V
Vin = 1.2 V
Vin = 1.5 V
40
NCP1402SN30T1
L = 47 mH
TA = 25°C
20
Vin = 3.0 V
Vin = 1.2 V
Vin = 2.0 V
Vin = 0.9 V
40
NCP1402SN50T1
L = 47 mH
TA = 25°C
20
0
Vin = 1.5 V
60
0
0
20
40
60
80
100 120 140 160 180 200
0
20
40
60
80
100 120 140 160 180 200
IO, OUTPUT CURRENT (mA)
IO, OUTPUT CURRENT (mA)
Figure 7. NCP1402SN30T1 Efficiency vs.
Output Current
Figure 8. NCP1402SN50T1 Efficiency vs.
Output Current
http://onsemi.com
5
NCP1402
3.2
VOUT, OUTPUT VOLTAGE (V)
VOUT, OUTPUT VOLTAGE (V)
2.1
2.0
1.9
1.8
1.7
NCP1402SN19T1
VOUT = 1.9 V x 0.96
Open−Loop Test
1.6
−50
−25
0
25
50
75
3.0
2.9
2.8
NCP1402SN30T1
VOUT = 3.0 V x 0.96
Open−Loop Test
2.7
−50
100
−25
25
50
75
100
TEMPERATURE (°C)
Figure 9. NCP1402SN19T1 Output Voltage vs.
Temperature
Figure 10. NCP1402SN30T1 Output Voltage vs.
Temperature
100
5.1
IDD1, OPERATING CURRENT 1 (mA)
NCP1402SN50T1
VOUT = 5.0 V x 0.96
Open−Loop Test
5.0
4.9
4.8
4.7
−50
−25
0
25
50
75
80
60
40
20
0
−50
100
NCP1402SN19T1
VOUT = 1.9 V x 0.96
Open−Loop Test
−25
TEMPERATURE (°C)
50
75
100
100
IDD1, OPERATING CURRENT 1 (mA)
NCP1402SN30T1
VOUT = 3.0 V x 0.96
Open−Loop Test
60
40
20
0
−50
25
Figure 12. NCP1402SN19T1 Operating
Current 1 vs. Temperature
100
80
0
TEMPERATURE (°C)
Figure 11. NCP1402SN50T1 Output Voltage vs.
Temperature
IDD1, OPERATING CURRENT 1 (mA)
0
TEMPERATURE (°C)
5.2
VOUT, OUTPUT VOLTAGE (V)
3.1
−25
0
25
50
75
80
60
40
20
0
−50
100
NCP1402SN50T1
VOUT = 5.0 V x 0.96
Open−Loop Test
−25
0
25
50
75
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 13. NCP1402SN30T1 Operating
Current 1 vs. Temperature
Figure 14. NCP1402SN50T1 Operating
Current 1 vs. Temperature
http://onsemi.com
6
100
NCP1402
7.5
ton, SWITCH ON TIME (ms)
ton, SWITCH ON TIME (ms)
7.5
7.0
6.5
6.0
NCP1402SN19T1
VOUT = 1.9 V x 0.96
Open−Loop Test
5.5
5.0
−50
−25
0
25
50
75
−25
0
25
50
75
Figure 16. NCP1402SN30T1 Switch On Time
vs. Temperature
toff, MINIMUM SWITCH OFF TIME (ms)
NCP1402SN50T1
VOUT = 5.0 V x 0.96
Open−Loop Test
−25
0
25
50
75
100
1.8
1.7
1.6
1.5
1.4
−50
NCP1402SN19T1
VOUT = 1.9 V x 0.96
Open−Loop Test
−25
0
25
50
75
TEMPERATURE (°C)
Figure 17. NCP1402SN50T1 Switch On Time
vs. Temperature
Figure 18. NCP1402SN19T1 Minimum Switch
Off Time vs. Temperature
1.8
1.7
1.6
1.5
NCP1402SN30T1
VOUT = 3.0 V x 0.96
Open−Loop Test
−25
0
25
50
75
100
100
1.8
1.7
1.6
1.5
1.4
1.3
−50
NCP1402SN50T1
VOUT = 5.0 V x 0.96
Open−Loop Test
−25
0
25
50
75
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 19. NCP1402SN30T1 Minimum Switch
Off Time vs. Temperature
Figure 20. NCP1402SN50T1 Minimum Switch
Off Time vs. Temperature
http://onsemi.com
7
100
1.9
TEMPERATURE (°C)
toff, MINIMUM SWITCH OFF TIME (ms)
ton, SWITCH ON TIME (ms)
toff, MINIMUM SWITCH OFF TIME (ms)
NCP1402SN30T1
VOUT = 3.0 V x 0.96
Open−Loop Test
Figure 15. NCP1402SN19T1 Switch On Time
vs. Temperature
5.5
1.3
−50
5.5
TEMPERATURE (°C)
6.0
1.4
6.0
TEMPERATURE (°C)
6.5
4.5
−50
6.5
5.0
−50
100
7.0
5.0
7.0
100
NCP1402
100
DMAX, MAXIMUM DUTY CYCLE (%)
DMAX, MAXIMUM DUTY CYCLE (%)
100
90
80
70
60
50
40
−50
NCP1402SN19T1
VOUT = 1.9 V x 0.96
Open−Loop Test
−25
0
25
50
75
NCP1402SN30T1
VOUT = 3.0 V x 0.96
Open−Loop Test
−25
0
25
50
75
Figure 22. NCP1402SN30T1 Maximum Duty
Cycle vs. Temperature
ILX, LX PIN ON−STATE CURRENT (mA)
60
NCP1402SN50T1
VOUT = 5.0 V x 0.96
Open−Loop Test
−25
0
25
50
75
100
180
160
140
120
100
−50
NCP1402SN19T1
VOUT = 1.9 V x 0.96
VLX = 0.4 V
Open−Loop Test
−25
0
25
50
75
TEMPERATURE (°C)
Figure 23. NCP1402SN50T1 Maximum Duty
Cycle vs. Temperature
Figure 24. NCP1402SN19T1 LX Pin On−State
Current vs. Temperature
250
230
210
190
NCP1402SN30T1
VOUT = 3.0 V x 0.96
VLX = 0.4 V
Open−Loop Test
−25
0
25
50
75
100
100
300
275
250
225
200
175
−50
NCP1402SN50T1
VOUT = 5.0 V x 0.96
VLX = 0.4 V
Open−Loop Test
−25
0
25
50
75
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 25. NCP1402SN30T1 LX Pin On−State
Current vs. Temperature
Figure 26. NCP1402SN50T1 LX Pin On−State
Current vs. Temperature
http://onsemi.com
8
100
200
TEMPERATURE (°C)
ILX, LX PIN ON−STATE CURRENT (mA)
DMAX, MAXIMUM DUTY CYCLE (%)
ILX, LX PIN ON−STATE CURRENT (mA)
50
Figure 21. NCP1402SN19T1 Maximum Duty
Cycle vs. Temperature
70
150
−50
60
TEMPERATURE (°C)
80
170
70
TEMPERATURE (°C)
90
40
−50
80
40
−50
100
100
50
90
100
NCP1402
1.0
VLXLIM, VLX VOLTAGE LIMIT (V)
VLXLIM, VLX VOLTAGE LIMIT (V)
1.0
0.8
0.6
0.4
0.2
NCP1402SN19T1
Open−Loop Test
0.0
−50
−25
0
25
50
75
0.4
0.2
NCP1402SN30T1
Open−Loop Test
−25
0
25
50
75
100
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 27. NCP1402SN19T1 VLX Voltage Limit
vs. Temperature
Figure 28. NCP1402SN30T1 VLX Voltage Limit
vs. Temperature
RDS(on), SWITCH−ON RESISTANCE (W)
0.8
0.6
0.4
0.2
NCP1402SN50T1
Open−Loop Test
0.0
−50
−25
0
25
50
75
100
4.0
3.5
3.0
2.5
2.0
1.5
1.0
−50
NCP1402SN19T1
VOUT = 1.9 V x 0.96
VLX = 0.4 V
Open−Loop Test
−25
0
25
50
75
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 29. NCP1402SN50T1 VLX Voltage Limit
vs. Temperature
Figure 30. NCP1402SN19T1 Switch−on
Resistance vs. Temperature
3.0
RDS(on), SWITCH−ON RESISTANCE (W)
VLXLIM, VLX VOLTAGE LIMIT (V)
0.6
0.0
−50
100
1.0
RDS(on), SWITCH−ON RESISTANCE (W)
0.8
2.5
2.0
1.5
1.0
0.5
0.0
−50
NCP1402SN30T1
VOUT = 3.0 V x 0.96
VLX = 0.4 V
Open−Loop Test
−25
0
25
50
75
100
3.0
2.5
2.0
1.5
1.0
0.5
0.0
−50
NCP1402SN50T1
VOUT = 5.0 V x 0.96
VLX = 0.4 V
Open−Loop Test
−25
0
25
50
75
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 31. NCP1402SN30T1 Switch−on
Resistance vs. Temperature
Figure 32. NCP1402SN50T1 Switch−on
Resistance vs. Temperature
http://onsemi.com
9
100
100
Vstart
0.8
NCP1402SN19T1
L = 22 mH
COUT = 10 mF
IO = 0 mA
0.4
0.2
Vhold
0.0
−50
−25
0
25
75
50
100
NCP1402SN50T1
L = 22 mH
COUT = 10 mF
IO = 0 mA
Vhold
0.2
−25
25
0
50
75
100
0.4
0.2
Vhold
0.0
−50
−25
0
25
50
75
100
2.0
1.5
Vstart
1.0
Vhold
NCP1402SN19T1
L = 47 mH
COUT = 68 mF
TA = 25°C
0.5
0.0
0
10
20
30
40
50
60
70
80
90 100
TEMPERATURE (°C)
IO, OUTPUT CURRENT (mA)
Figure 35. NCP1402SN50T1 Startup/Hold
Voltage vs. Temperature
Figure 36. NCP1402SN19T1 Startup/Hold
Voltage vs. Output Current
2.0
1.5
Vstart
1.0
Vhold
NCP1402SN30T1
L = 47 mH
COUT = 68 mF
TA = 25°C
0.5
0.0
0
NCP1402SN30T1
L = 22 mH
COUT = 10 mF
IO = 0 mA
0.6
Figure 34. NCP1402SN30T1 Startup/Hold
Voltage vs. Temperature
0.8
0.0
−50
0.8
Figure 33. NCP1402SN19T1 Startup/Hold
Voltage vs. Temperature
Vstart
0.4
Vstart
TEMPERATURE (°C)
1.0
0.6
1.0
TEMPERATURE (°C)
Vstart/Vhold, STARTUP/HOLD VOLTAGE (V)
0.6
Vstart/Vhold, STARTUP/HOLD VOLTAGE (V)
1.0
Vstart/Vhold, STARTUP/HOLD VOLTAGE (V)
Vstart/Vhold, STARTUP/HOLD VOLTAGE (V)
Vstart/Vhold, STARTUP/HOLD VOLTAGE (V)
Vstart/Vhold, STARTUP/HOLD VOLTAGE (V)
NCP1402
10
20
30
40
50
60
70
80
90 100
2.0
1.5
Vstart
1.0
0.5
NCP1402SN50T1
L = 47 mH
COUT = 68 mF
TA = 25°C
Vhold
0.0
0
10
20
30
40
50
60
70
80
90 100
IO, OUTPUT CURRENT (mA)
IO, OUTPUT CURRENT (mA)
Figure 37. NCP1402SN30T1 Startup/Hold
Voltage vs. Output Current
Figure 38. NCP1402SN50T1 Startup/Hold
Voltage vs. Output Current
http://onsemi.com
10
NCP1402
5 ms/div
VOUT = 1.9 V, Vin = 1.2 V, IO = 30 mA, L = 47 mH, COUT = 68 mF
1. VLX, 1.0 V/div
2. VOUT, 20 mV/div, AC coupled
3. IL, 100 mA/div
5 ms/div
VOUT = 1.9 V, Vin = 1.2 V, IO = 70 mA, L = 47 mH, COUT = 68 mF
1. VLX, 1.0 V/div
2. VOUT, 20 mV/div, AC coupled
3. IL, 100 mA/div
Figure 39. NCP1402SN19T1 Operating
Waveforms (Medium Load)
Figure 40. NCP1402SN19T1 Operating
Waveforms (Heavy Load)
2 ms/div
VOUT = 3.0 V, Vin = 1.2 V, IO = 30 mA, L = 47 mH, COUT = 68 mF
1. VLX, 2.0 V/div
2. VOUT, 20 mV/div, AC coupled
3. IL, 100 mA/div
2 ms/div
VOUT = 3.0 V, Vin = 1.2 V, IO = 70 mA, L = 47 mH, COUT = 68 mF
1. VLX, 2.0 V/div
2. VOUT, 20 mV/div, AC coupled
3. IL, 100 mA/div
Figure 41. NCP1402SN30T1 Operating
Waveforms (Medium Load)
Figure 42. NCP1402SN30T1 Operating
Waveforms (Heavy Load)
2 ms/div
2 ms/div
VOUT = 5.0 V, Vin = 1.5 V, IO = 30 mA, L = 47 mH, COUT = 68 mF
1. VLX, 2.0 V/div
2. VOUT, 20 mV/div, AC coupled
3. IL, 100 mA/div
VOUT = 5.0 V, Vin = 1.5 V, IO = 60 mA, L = 47 mH, COUT = 68 mF
1. VLX, 2.0 V/div
2. VOUT, 20 mV/div, AC coupled
3. IL, 100 mA/div
Figure 43. NCP1402SN50T1 Operating
Waveforms (Medium Load)
Figure 44. NCP1402SN50T1 Operating
Waveforms (Heavy Load)
http://onsemi.com
11
NCP1402
Vin = 1.2 V, L = 47 mH, COUT = 68 mF
1. VOUT = 1.9 V (AC coupled), 100 mV/div
2. IO = 0.1 mA to 80 mA
Vin = 1.2 V, L = 47 mH, COUT = 68 mF
1. VOUT = 1.9 V (AC coupled), 100 mV/div
2. IO = 80 mA to 0.1 mA
Figure 45. NCP1402SN19T1 Load Transient
Response
Figure 46. NCP1402SN19T1 Load Transient
Response
Vin = 1.5 V, L = 47 mH, COUT = 68 mF
1. VOUT = 3.0 V (AC coupled), 100 mV/div
2. IO = 0.1 mA to 80 mA
Vin = 1.5 V, L = 47 mH, COUT = 68 mF
1. VOUT = 3.0 V (AC coupled), 100 mV/div
2. IO = 80 mA to 0.1 mA
Figure 47. NCP1402SN30T1 Load Transient
Response
Figure 48. NCP1402SN30T1 Load Transient
Response
Vin = 2.4 V, L = 47 mH, COUT = 68 mF
1. VOUT = 5.0 V (AC coupled), 100 mV/div
2. IO = 0.1 mA to 80 mA
Vin = 2.4 V, L = 47 mH, COUT = 68 mF
1. VOUT = 5.0 V (AC coupled), 100 mV/div
2. IO = 80 mA to 0.1 mA
Figure 49. NCP1402SN50T1 Load Transient
Response
Figure 50. NCP1402SN50T1 Load Transient
Response
http://onsemi.com
12
NCP1402
100
NCP1402SN19T1
L = 47 mH
COUT = 68 mF
TA = 25°C
80
Vripple, RIPPLE VOLTAGE (mV)
Vripple, RIPPLE VOLTAGE (mV)
100
60
40
Vin = 1.2 V
Vin = 1.5 V
20
NCP1402SN30T1
L = 47 mH
COUT = 68 mF
TA = 25°C
80
Vin = 2.0 V
60
Vin = 0.9 V
Vin = 1.2 V
Vin = 1.5 V
40
Vin = 2.5 V
20
Vin = 0.9 V
0
0
0
20
40
60
80
100 120 140 160 180 200
0
60
80
100 120 140 160 180 200
Figure 51. NCP1402SN19T1 Ripple Voltage vs.
Output Current
Figure 52. NCP1402SN30T1 Ripple Voltage vs.
Output Current
100
IDD1, OPERATING CURRENT 1 (mA)
Vripple, RIPPLE VOLTAGE (mV)
40
IO, OUTPUT CURRENT (mA)
100
Vin = 4.0 V
80
Vin = 2.0 V
Vin = 1.5 V
60
Vin = 3.0 V
Vin = 1.2 V
40
NCP1402SN50T1
L = 47 mH
COUT = 68 mF
TA = 25°C
20
Vin = 0.9 V
0
80
85°C
25°C
60
−40°C
40
NCP1402SNXXT1
VOUT = VSET x 0.96
Open−loop Test
20
0
0
20
40
60
80
100 120 140 160 180 200
2
3
4
6
5
IO, OUTPUT CURRENT (mA)
VOUT, OUTPUT VOLTAGE (V)
Figure 53. NCP1402SN50T1 Ripple Voltage vs.
Output Current
Figure 54. NCP1402SNXXT1 Operating
Current 1 vs. Output Voltage
300
−40°C
260
220
25°C
85°C
180
NCP1402SNXXT1
VOUT = VSET x 0.96
VLX = 0.4 V
Open−loop Test
140
100
1
1
RDS(ON), SWITCH−ON RESISTANCE (W)
ILX, LX PIN ON−STATE CURRENT (mA)
20
IO, OUTPUT CURRENT (mA)
2
3
4
6
5
3.5
NCP1402SNXXT1
VOUT = VSET x 0.96
VLX = 0.4 V
Open−loop Test
3.0
2.5
85°C
2.0
25°C
1.5
−40°C
1.0
1
2
3
4
5
VOUT, OUTPUT VOLTAGE (V)
VOUT, OUTPUT VOLTAGE (V)
Figure 55. NCP1402SNXXT1 Pin On−state
Current vs. Output Voltage
Figure 56. NCP1402SNXXT1 Switch−On
Resistance vs. Output Voltage
http://onsemi.com
13
6
150
IO(max), MAX. OUTPUT CURRENT (mA)
Iin(no load), NO LOAD INPUT CURRENT (mA)
NCP1402
NCP1402SNXXT1
L = 47 mH
IO = 0 mA
TA = 25°C
5.0 V
125
100
3.3 V
75
3.0 V
50
2.7 V
25
1.9 V
0
0
1
2
3
4
5
6
400
3.3 V
5.0 V
3.0 V
300
2.7 V
200
1.9 V
100
NCP1402SNXXT1
L = 47 mH
TA = 25°C
0
0
1
2
3
4
Vin, INPUT VOLTAGE (V)
Vin, INPUT VOLTAGE (V)
Figure 57. NCP1402SNXXT1 No Load Input
Current vs. Input Voltage
Figure 58. NCP1402SNXXT1 Maximum Output
Current vs. Input Voltage
5
DETAILED OPERATING DESCRIPTION
Operation
Soft−Start
The NCP1402 series are monolithic power switching
regulators optimized for applications where power drain
must be minimized. These devices operate as variable
frequency, voltage mode boost regulators and designed to
operate in continuous conduction mode. Potential
applications include low powered consumer products and
battery powered portable products.
The NCP1402 series are low noise variable frequency
voltage−mode DC−DC converters, and consist of Soft−Start
circuit, feedback resistor, reference voltage, oscillator, PFM
comparator, PFM control circuit, current limit circuit and
power switch. Due to the on−chip feedback resistor network,
the system designer can get the regulated output voltage
from 1.8 V to 5 V with a small number of external
components. The operating current is typically 30 mA
(VOUT = 1.9 V), and can be further reduced to about 0.6 mA
when the chip is disabled (VCE < 0.3 V).
The NCP1402 operation can be best understood by
examining the block diagram in Figure 2. PFM comparator
monitors the output voltage via the feedback resistor. When
the feedback voltage is higher than the reference voltage, the
power switch is turned off. As the feedback voltage is lower
than reference voltage and the power switch has been off for
at least a period of minimum off−time decided by PFM
oscillator, the power switch is then cycled on for a period of
on−time also decided by PFM oscillator, or until current
limit signal is asserted. When the power switch is on, current
ramps up in the inductor, storing energy in the magnetic
field. When the power switch is off, the energy in the
magnetic field is transferred to output filter capacitor and the
load. The output filter capacitor stores the charge while the
inductor current is high, then holds up the output voltage
until next switching cycle.
There is a Soft−Start circuit in NCP1402. When power is
applied to the device, the Soft−Start circuit pumps up the
output voltage to approximately 1.5 V at a fixed duty cycle, the
level at which the converter can operate normally. What is
more, the startup capability with heavy loads is also improved.
Regulated Converter Voltage (VOUT)
The VOUT is set by an internal feedback resistor network.
This is trimmed to a selected voltage from 1.8 to 5.0 V range
in 100 mV steps with an accuracy of ±2.5%.
Current Limit
The NCP1402 series utilizes cycle−by−cycle current
limiting as a means of protecting the output switch
MOSFET from overstress and preventing the small value
inductor from saturation. Current limiting is implemented
by monitoring the output MOSFET current build−up during
conduction, and upon sensing an overcurrent conduction
immediately turning off the switch for the duration of the
oscillator cycle.
The voltage across the output MOSFET is monitored and
compared against a reference by the VLX limiter. When the
threshold is reached, a signal is sent to the PFM controller
block to terminate the power switch conduction. The current
limit threshold is typically set at 350 mA.
Enable / Disable Operation
The NCP1402 series offer IC shut−down mode by chip
enable pin (CE pin) to reduce current consumption. An
internal pullup resistor tied the CE pin to OUT pin by default
i.e. user can float the pin CE for permanent “On”. When
voltage at pin CE is equal or greater than 0.9 V, the chip will
be enabled, which means the regulator is in normal
operation. When voltage at pin CE is less than 0.3 V, the chip
is disabled, which means IC is shutdown.
Important: DO NOT apply a voltage between 0.3 V and 0.9 V to pin CE as this is the CE pin’s hyteresis voltage
range. Clearly defined output states can only be obtained by applying voltage out of this range.
http://onsemi.com
14
NCP1402
APPLICATIONS CIRCUIT INFORMATION
L1
Vin
C1
10 mF
CE
D1
47 mH
1
OUT NCP1402
2
NC
LX
5
VOUT
C2
68 mF
GND
4
3
Figure 59. Typical Application Circuit
Step−up Converter Design Equations
enough to maintain low ripple. Low inductance values
supply higher output current, but also increase the ripple and
reduce efficiency. Note that values below 27 mH is not
recommended due to NCP1402 switch limitations. Higher
inductor values reduce ripple and improve efficiency, but
also limit output current.
The inductor should have small DCR, usually less than 1 W
to minimize loss. It is necessary to choose an inductor with
saturation current greater than the peak current which the
inductor will encounter in the application.
NCP1402 step−up DC−DC converter designed to operate
in continuous conduction mode can be defined by:
Calculation
Equation
2
ǒVOUTVinIOmax
Ǔ
vM
L
IPK
(Vin * Vs)ton
) I min
L
Imin
(ton ) toff)IO (Vin * VS)ton
*
2L
toff
(VOUT ) VF * Vin)
DQ
*NOTES:
−
IPK
Imin −
−
IO
IOmax −
−
IL
−
Vin
VOUT −
−
VF
−
VS
DQ
−
Vripple −
ESR −
M
−
The diode is the main source of loss in DC−DC converters.
The most importance parameters which affect their
efficiency are the forward voltage drop, VF, and the reverse
recovery time, trr. The forward voltage drop creates a loss
just by having a voltage across the device while a current
flowing through it. The reverse recovery time generates
a loss when the diode is reverse biased, and the current
appears to actually flow backwards through the diode due to
the minority carriers being swept from the P−N junction.
A Schottky diode with the following characteristics is
recommended:
Small forward voltage, VF < 0.3 V
Small reverse leakage current
Fast reverse recovery time/ switching speed
Rated current larger than peak inductor current,
Irated > IPK
Reverse voltage larger than output voltage,
Vreverse > VOUT
(Vin * Vs)ton
toff
Vripple
Diode
(IL * IO)toff
[
DQ
) (IL * IO)ESR
COUT
Peak inductor current
Minimum inductor current
Desired dc output current
Desired maximum dc output current
Average inductor current
Nominal operating dc input voltage
Desired dc output voltage
Diode forward voltage
Saturation voltage of the internal FET switch
Charge stores in the COUT during charging up
Output ripple voltage
Equivalent series resistance of the output capacitor
An empirical factor, when VOUT ≥ 3.0 V,
M = 8 x 10−6, otherwise M = 5.3 x 10−6.
Input Capacitor
EXTERNAL COMPONENT SELECTION
The input capacitor can stabilize the input voltage and
minimize peak current ripple from the source. The value of
the capacitor depends on the impedance of the input source
used. Small Equivalent Series Resistance (ESR) Tantalum or
ceramic capacitor with value of 10 mF should be suitable.
Inductor
The NCP1402 is designed to work well with a 47 mH
inductor in most applications. 47 mH is a sufficiently low
value to allow the use of a small surface mount coil, but large
http://onsemi.com
15
NCP1402
Output Capacitor
An evaluation board of NCP1402 has been made in the
size of 23 mm x 20 mm only, as shown in Figures 60 and 61.
Please contact your ON Semiconductor representative for
availability. The evaluation board schematic diagram, the
artwork and the silkscreen of the surface mount PCB are
shown below:
The output capacitor is used for sustaining the output
voltage when the internal MOSFET is switched on and
smoothing the ripple voltage. Low ESR capacitor should be
used to reduce output ripple voltage. In general, a 47 mF to
68 mF low ESR (0.15 W to 0.30 W) Tantalum capacitor
should be appropriate. For applications where space is
a critical factor, two parallel 22 mF low profile SMD ceramic
capacitors can be used.
20 mm
23 mm
Figure 60. NCP1402 PFM Step−Up DC−DC Converter Evaluation Board Silkscreen
20 mm
23 mm
Figure 61. NCP1402 PFM Step−Up DC−DC Converter Evaluation Board Artwork (Component Side)
http://onsemi.com
16
NCP1402
Components Supplier
Supplier
Part Number
Inductor, L1
Parts
Sumida Electric Co. Ltd.
CD54−470L
Schottky Diode, D1
ON Semiconductor Corp.
MBR0520LT1
Description
Phone
Inductor 47 mH / 0.72 A
(852)−2880−6688
Schottky Power Rectifier
(852)−2689−0088
(852)−2305−1168
(852)−2305−1168
Output Capacitor, C2
KEMET Electronics Corp.
T494D686K010AS
Low ESR Tantalum Capacitor
68 mF / 10 V
Input Capacitor, C1
KEMET Electronics Corp.
T491C106K016AS
Low Profile Tantalum Capacitor
10 mF / 16 V
PCB Layout Hints
Grounding
efficiency (short and thick traces for connecting the inductor
L can also reduce stray inductance), e.g.: short and thick
traces listed below are used in the evaluation board:
1. Trace from TP1 to L1
2. Trace from L1 to Lx pin of U1
3. Trace from L1 to anode pin of D1
4. Trace from cathode pin of D1 to TP2
One point grounding should be used for the output power
return ground, the input power return ground, and the device
switch ground to reduce noise as shown in Figure 62, e.g.:
C2 GND, C1 GND, and U1 GND are connected at one point
in the evaluation board. The input ground and output ground
traces must be thick enough for current to flow through and
for reducing ground bounce.
Output Capacitor
Power Signal Traces
The output capacitor should be placed close to the output
terminals to obtain better smoothing effect on the output
ripple.
Low resistance conducting paths should be used for the
power carrying traces to reduce power loss so as to improve
L1
TP1
Vin
TP2
47 mH
C1
10 mF/16 V
+
JP1
Enable
On
Off
LX
CE
1
OUT NCP1402
2
NC
TP4
GND
Vout
D1
MBR0520LT1
+
5
C2
68 mF/10 V
GND
TP3
4
3
GND
Figure 62. NCP1402 Evaluation Board Schematic Diagram
ORDERING INFORMATION
Device
Output Voltage
Device Marking
NCP1402SN19T1G
1.9 V
DAU
NCP1402SN27T1G
2.7 V
DAE
NCP1402SN30T1G
3.0 V
DAF
NCP1402SN33T1G
3.3 V
DAG
NCP1402SN40T1G
4.0 V
DCR
NCP1402SN50T1G
5.0 V
DAH
Package
Shipping†
SOT23−5
(Pb−Free)
3,000 Units/Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
NOTE: The ordering information lists five standard output voltage device options. Additional device with output voltage ranging from 1.8 V to
5.0 V in 100 mV increments can be manufactured. Contact your ON Semiconductor representative for availability.
http://onsemi.com
17
NCP1402
PACKAGE DIMENSIONS
SOT23−5
(TSOP−5, SC59−5)
SN SUFFIX
CASE 483−02
ISSUE K
NOTE 5
2X
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH
THICKNESS. MINIMUM LEAD THICKNESS IS THE
MINIMUM THICKNESS OF BASE MATERIAL.
4. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH, PROTRUSIONS, OR GATE BURRS. MOLD
FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT
EXCEED 0.15 PER SIDE. DIMENSION A.
5. OPTIONAL CONSTRUCTION: AN ADDITIONAL
TRIMMED LEAD IS ALLOWED IN THIS LOCATION.
TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2
FROM BODY.
D 5X
0.20 C A B
0.10 T
M
2X
0.20 T
B
5
1
4
2
S
3
K
B
DETAIL Z
G
A
A
TOP VIEW
DIM
A
B
C
D
G
H
J
K
M
S
DETAIL Z
J
C
0.05
H
SIDE VIEW
C
SEATING
PLANE
END VIEW
MILLIMETERS
MIN
MAX
3.00 BSC
1.50 BSC
0.90
1.10
0.25
0.50
0.95 BSC
0.01
0.10
0.10
0.26
0.20
0.60
0_
10 _
2.50
3.00
SOLDERING FOOTPRINT*
0.95
0.037
1.9
0.074
2.4
0.094
1.0
0.039
0.7
0.028
SCALE 10:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
18
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP1402/D