Ordering number : EN6204A LB1867M Monolithic Digital IC 2-phase Brushless http://onsemi.com Fan Motor Driver Overview The LB1867M is a 2-phase unipolar brushless motor driver. With only a few peripheral parts, lockup protection and automatic recovery can be implemented. The IC can be configured for 12V or 24V operation and a wide range of variations, from Low speed to H-High speed and from 60cm to 120cm square using the same PCB. This makes it easy to design highly reliable fan motor installations. Features • Output protection Zener diode with variable withstand voltage Z1, Z2 pins open: VOLM = 57V (24V specification) Z1, Z2 pins shorted: VOLM = 32V (12V specification) External Zener diode connected across Z1 − VCC pins: support for fans with large drive current • External resistor allows configuration for 12V or 24V • Direct Hall element connection possible (built-in Hall amplifier with hysteresis supports core without auxiliary electrode) • Built-in output transistor with 1.0A output current (strengthened negative-current support for core without auxiliary electrode) • Built-in rotation detection function: Low during rotation and High during stop • Built-in lockup protection with automatic recovery • Built-in thermal shutdown Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Symbol Conditions t ≤ 20ms Ratings Unit Maximum input current ICC max 200 Maximum applied output voltage VOUT max Maximum output current IOUT max 1.0 A Maximum current flowing into RD pin IRD max 10 mA Maximum RD applied voltage VRD max Allowable power dissipation Pd max Operating temperature Topr -30 to +80 °C Storage temperature Tstg -55 to +150 °C Internal Mounted on a specified board * mA V 30 V 800 mW * Specified board: 20mm × 15mm × 1.5mm, glass epoxy board. Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Semiconductor Components Industries, LLC, 2013 May, 2013 31109 MS 20080221-S00008 / 83100RM(KI) No.6204-1/5 LB1867M Allowable Operating Ranges at Ta = 25°C Parameter Symbol Input current range ICC Common mode input voltage range VICM Conditions Ratings Unit 6.0 to 50 mA 0.2 to VIN-1.5 V Electrical Characteristics at Ta = 25°C, ICC = 10mA Parameter Symbol Ratings Conditions min Output limiter withstand voltage VOLM1 Output saturation voltage typ Z1, Z2 open 54 VOLM2 Z1, Z2 short 31 VOsat1 IO = 0.5A VOsat2 IO = 1.0A VIN ICC = 7.0mA Hall input sensitivity (at zero peak) VHN Including offset and hysteresis RD output saturation voltage VRDsat IRD = 5mA CT drain current IC1 C = GND 2.7 CT discharge current IC2 C = VIN Comp input threshold voltage VTH1 VTH2 VIN voltage Thermal protection operating Unit max 57 60 V 33 35 V 0.95 1.2 V 1.15 1.5 V 6.7 7.0 V 20 mV 0.1 0.3 V 3.8 4.9 μA 0.19 0.30 0.41 μA 0.77 0.8VIN 0.83 V 0.42 0.45VIN 0.48 V 6.4 TSD Design target value * 180 °C ΔTSD Design target value * 40 °C temperature Thermal protection circuit hysteresis * Design target value, Do not measurement. Package Dimensions unit : mm (typ) 3111A Pd max -- Ta 8.0 14 0.63 4.4 6.4 8 1 1.7MAX 7 1.0 0.35 0.15 0.1 (1.5) (1.0) SANYO : MFP14S(225mil) Allowable power dissipation, Pd max -- W 1.0 Specified board: 20×15×1.5mm3 glass epoxy board. 0.8 0.6 0.4 0.2 0 -30 -20 0 20 40 60 80 100 Ambient temperature, Ta -- °C No.6204-2/5 LB1867M Pin Assignment 14 VIN IN+ 2 13 RD CT 3 12 Z2 LB1867M IN− 1 NC 4 OUT1 5 11 Z1 10 OUT2 NC 6 9 NC GND 7 8 NC Top view Pin Function Pin No. Pin name Function 1 IN− Hall input + pin. Hysteresis amplifier 2 IN+ Hall input − pin. Hysteresis amplifier 3 CT Lockup protection time setting capacitor pin (0.47 to 4.7μF). 5 OUT1 Output 1 pin. 10 OUT2 Output 2 pin. 7 GND GND pin. 11 Z1 External Zener diode pin (external Zener diode to be connected between power supply and Z1). 12 Z2 Kickback absorption voltage alteration pin (shorted to Z1: 12V operation). 13 RD Lockup detection pin (latch type). 14 VIN Regulated power supply input pin (limiting resistor to be inserted between power supply and VIN). Truth Table IN+ IN− CT OUT1 OUT2 RD H L L H L L L H L L H L H L H H H H L H H H H H * RD is a latch type output No.6204-3/5 LB1867M Block Diagram VIN VCC L1 Thermal shutdown R1 L2 OUT1 R2 IN+ H IN− Control block Z1 Constant current source Z2 OUT2 CT RD C1 GND 0.47 to 10μF Application Circuit Example (1) 12V supply voltage VCC 12V 330Ω 14 VIN 2kΩ 13 RD 12 Z2 11 Z1 10 OUT2 9 NC 8 NC NC 6 GND 7 LB1867M IN− 1 H IN+ 2 CT 3 NC 4 OUT1 5 0.47μF No.6204-4/5 LB1867M (2) 24V supply voltage VCC 24V 1.2kΩ 14 VIN 2kΩ 13 RD 11 Z1 12 Z2 10 OUT2 9 NC 8 NC OUT1 5 NC 6 GND 7 10 OUT2 9 NC 8 NC NC 6 GND 7 LB1867M IN− 1 IN+ 2 CT 3 H NC 4 0.47μF (3) High-Power Fan (120mm-HH-Speed) VCC 12V (24V) 330Ω (1.2kΩ) 14 VIN 2kΩ VZ=12V (24V) 13 RD 12 Z2 11 Z1 LB1867M IN− 1 H IN+ 2 CT 3 NC 4 OUT1 5 0.47μF ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PS No.6204-5/5