NCN5192 D

NCN5192
HART Modem
Description
The NCN5192 is a single−chip, CMOS modem for use in highway
addressable remote transducer (HART) field instruments and masters.
The modem and a few external passive components provide all of the
functions needed to satisfy HART physical layer requirements
including modulation, demodulation, receive filtering, carrier detect,
and transmit−signal shaping. In addition, the NCN5192 also has an
integrated DAC for low-BOM current loop slave transmitter
implementation.
The NCN5192 uses phase continuous frequency shift keying (FSK)
at 1200 bits per second. To conserve power the receive circuits are
disabled during transmit operations and vice versa. This provides the
half−duplex operation used in HART communications.
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Single−chip, Half−duplex 1200 Bits per Second FSK Modem
Bell 202 Shift Frequencies of 1200 Hz and 2200 Hz
3.0 V − 5.5 V Power Supply
Transmit−signal Wave Shaping
Receive Band−pass Filter
Low Power: Optimal for Intrinsically Safe Applications
Compatible with 3.3 V or 5 V Microcontroller
Internal Oscillator Requires 460.8 kHz, 920 kHz or 1.8 MHz Crystal
or Ceramic Resonator
SPI Communication
Integrated 16 bit Sigma-Delta DAC
Meets HART Physical Layer Requirements
Industrial Temperature Range of −40°C to +85°C
Available in 32−pin NQFP Package
These are Pb−Free Devices
http://onsemi.com
MARKING
DIAGRAM
1
1
32
QFN32
CASE 488AM
NCN
5192
AWLYYWW
G
NCN5192 = Specific Device Code
A
= Assembly Location
WL
= Wafer Lot
YY
= Year
WW
= Work Week
G
= Pb−Free Package
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 12 of this data sheet.
Applications
• HART Multiplexers
• HART Modem Interfaces
• 4 − 20 mA Loop Powered Transmitters
© Semiconductor Components Industries, LLC, 2014
February, 2014 − Rev. 3
1
Publication Order Number:
NCN5192/D
NCN5192
BLOCK DIAGRAM
VDD
RxD
RxAFI
VDDA
RxAF
RxA
Demodulator
Logic
RxD _ENH
Rx Comp
FSK _IN
Rx HP Filter
AREF
CD
Carrier Detect
Counter
CDREF
Carrier Comp
Numeric
Controlled
Oscillator
TxD
DEMODULATOR
TxA
Sine
Shaper
RTS
FSK _OUT
MODULATOR
NCN5192
CS
SCLK
DATA
SPI
VPOR
KICK
RESET
POR
JUMP
DAC
DACREF
DAC
CLK 1
Crystal
Oscillator
BIAS
CBIAS
VSS VSSA
CLK 2
XOUT XIN
Figure 1. Block Diagram NCN5192
ELECTRICAL SPECIFICATIONS
Table 1. ABSOLUTE MAXIMUM RATINGS (Note 1)
Parameter
Symbol
Min
Max
Units
TA
Ambient Temperature
−40
+85
°C
TS
Storage Temperature
−55
+150
°C
TJ
Junction Temperature
−40
+150
°C
Supply Voltage
−0.3
6.0
V
DC Input, Output
−0.3
VDD + 0.3
V
VDD
VIN, VOUT
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. CMOS devices are damaged by high−energy electrostatic discharge. Devices must be stored in conductive foam or with all pins shunted.
Precautions should be taken to avoid application of voltages higher than the maximum rating. Stresses above absolute maximum ratings
may result in damage to the device.
http://onsemi.com
2
NCN5192
Table 2. DC CHARACTERISTICS (VDD = 3.0 V to 5.5 V, VSS = 0 V, TA = −40°C to +85°C)
Parameter
Symbol
VDD
VDD
DC Supply Voltage
VIL
Input Voltage, Low
3.0 – 5.5 V
VIH
Input Voltage, High
3.0 – 5.5 V
VOL
Output Voltage, Low (IOL = 0.67 mA)
3.0 – 5.5 V
Output Voltage, High (IOH = −0.67 mA)
3.0 – 5.5 V
CIN
Input Capacitance of:
Analog Inputs
RxA
Digital Inputs
IIL/IIH
Input Leakage Current
IOLL
Output Leakage Current
IDD
Total Power Supply Current
IDDA
Static Analog Supply Current
IDDQ
Static Digital Current
IDDD
AREF
CBIAS
Typ
Max
Units
5.5
V
0.3 * VDD
V
3.0
VOH
CDREF
(Note 2)
Min
0.7 * VDD
V
0.4
V
2.4
V
2.9
25
3.5
175
pF
pF
pF
350
±500
nA
±10
mA
600
mA
330
370
mA
mA
3.3 V
5.0 V
150
150
0
30
mA
Dynamic Digital Current
5.0 V
25
200
mA
Analog Reference
3.3 V
5.0 V
1.2
2.6
V
V
Carrier Detect Reference (AREF – 0.08 V)
3.3 V
5.0 V
1.235
2.5
Comparator Bias Current
(RBIAS = 500 kW, AREF = 1.235 V)
1.15
2.42
V
2.5
mA
2. The HART specification requires carrier detect (CD) to be active between 80 and 120 mVp−p. Setting CDREF at AREF − 0.08 VDC will set
the carrier detect to a nominal 100 mVp−p.
Table 3. AC CHARACTERISTICS (VDD = 3.0 V to 5.5 V, VSS = 0 V, TA = −40°C to +85°C) (Note 3)
Description
Min
Typ
Max
Units
Receive analog input
Leakage current
Frequency – mark (logic 1)
Frequency – space (logic 0)
1190
2180
1200
2200
±150
1210
2220
nA
Hz
Hz
Output of the high−pass filter
Slew rate
Gain bandwidth (GBW)
Voltage range
150
0.15
VDD – 0.15
V/ms
kHz
V
±500
nA
Pin Name
RxA
RxAF
RxAFI
TxA
0.025
Carrier detect and receive filter input
Leakage current
Modulator output
Frequency – mark (logic 1)
Frequency – space (logic 0)
Amplitude (IAREF 1.235 V)
Slew Rate − mark (logic 1)
Slew Rate − space (logic 0)
Loading (IAREF = 1.235 V)
30
RxD
Receive digital output
Rise/fall time
20
CD
Carrier detect output
Rise/fall time
20
1196.9
2194.3
500
1860
3300
Hz
Hz
mV
V/s
V/s
kW
ns
ns
3. The modulator output frequencies are proportional to the input clock frequency (460.8 kHz/920 kHz/1.8 MHz).
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
http://onsemi.com
3
NCN5192
Table 4. MODEM CHARACTERISTICS (VDD = 3.0 V to 5.5 V, VSS = 0 V, TA = −40°C to +85°C)
Min
Parameter
Typ
Demodulator jitter
Conditions
1. Input frequencies at 1200 Hz ± 10 Hz, 2200 Hz ± 20 Hz
2. Clock frequency of 460.8 kHz ± 0.1%
3. Input (RxA) asymmetry, 0
Max
Units
12
% of 1 bit
Max
Units
1.0
%
kHz
1.0
%
kHz
1.0
%
MHz
60
%
V
Max
Units
Table 5. CERAMIC RESONATOR AND CRYSTAL − External Clock Specifications
(VDD = 3.0 V to 5.5 V, VSS = 0 V, TA = −40°C to +85°C)
Min
Parameter
Typ
Resonator
Tolerance
Frequency
460.8
Crystal or Resonator, 920 kHz
Tolerance
Frequency
921.6
Crystal, 1.8 MHz
Tolerance
Frequency
1.843
External
Duty cycle
Amplitude
40
50
VOH − VOL
Table 6. DAC CHARACTERISTICS (VDD = 3.0 V to 5.5 V, VSS = 0 V, TA = −40°C to +85°C)
Min
Parameter
Typ
Bandwidth
10
Hz
Accuracy
Return−to−Zero
Non Return−to−Zero
16
14
Bit
Bit
Maximum Output
Return−to−Zero
Non Return−to−Zero
AVDD/2
AVDD
V
V
Differential Non−linearity
Return−to−Zero
Non Return−to−Zero
0.5
0.25
0.75
0.75
LSB
LSB
Integral Non−linearity
Return−to−Zero
Non Return−to−Zero
2.0
1.0
4.0
2.0
LSB
LSB
http://onsemi.com
4
NCN5192
TYPICAL APPLICATION
POWER
3.0 to 5.5 V
VDD
RxAFI
VDDA
RESET
RxAF
RxA
HART IN
VPOR
KICK
RxD_ENH
VDDA
RxD
CD
TxD
AREF
NCN5192
LM285
RTS
mC
CDREF
CS
DATA
TxA
CLK
HART &
4 – 20 mA OUT
S
VDDA
DAC
CLK1
1. 8 MHz
CLK2
JUMP
XOUT
DACREF
XIN
CBIAS
VSS
VSSA
Figure 2. Application Diagram NCN5192
http://onsemi.com
5
RxD_ENH
CD
RxD
25
DACREF
28
26
DAC
29
27
CLK1
VDD
30
CLK2
31
32
NCN5192
SCLK
1
24
DATA
2
23
TxD
JUMP
3
22
RTS
KICK
4
21
VDD
CS
5
20
VSS
VSS
6
19
VSSA
TxA
7
18
XIN
AREF
8
17
XOUT
9
10
11
12
13
14
15
16
CDREF
CBIAS
VPOR
VSSA
VDDA
RxA
RxAF
RxAFI
NCN5192
RESET
Figure 3. Pin Out NCN5192 in 32-pin NQFP (top view)
Table 7. PIN OUT SUMMARY 32−PIN NQFP
Pin No.
Signal Name
Type
Pin Description
1
SCLK
Input
SPI Serial Clock
2
DATA
Input
SPI Serial Data
3
JUMP
Input
Sigma−Delta Modulator Alarm condition value
4
KICK
Input
Watchdog kick
SPI Serial Chip Select
5
CS
Input
6
VSS
Ground
Ground
7
TxA
Output
Transmit Data Modulator output
8
AREF
Input
Analog reference voltage
9
CDREF
Input
Carrier detect reference voltage
10
CBIAS
Output
Comparator bias current
11
VPOR
Input
POR measurement point
12
VSSA
Ground
Analog ground
13
VDDA
Power
Analog supply voltage
14
RxA
Input
15
RxAF
Output
16
RxAFI
Input
17
XOUT
Output
Receive Data Modulator input
Analog receive filter output
Analog receive comparator input
Crystal oscillator output
18
XIN
Input
19
VSSA
Ground
Crystal oscillator input
Analog ground
20
VSS
Ground
Ground
21
VDD
Power
Digital supply voltage
22
RTSB
Input
Request to send
23
TxD
Input
Input transmit data, transmit HART data stream from microcontroller
24
RESETB
Open Drain
25
RxD
Output
Received demodulated HART data to microcontroller
26
CD
Output
Carrier detect output
27
RxD_ENH
Output
not[CD] or RxD
28
DACREF
Input
29
DAC
Output
Sigma−Delta Modulator Output
30
VDD
Power
Digital supply voltage
31
CLK1
Output
Programmable Clock Output 1
32
CLK2
Output
Programmable Clock Output 2
EP
Exposed Pad
Power
Connect to VSS
Reset all digital logic when low
Sigma−Delta Modulator Reference Voltage
http://onsemi.com
6
NCN5192
Pin Descriptions
Table 8. PIN DESCRIPTIONS
Symbol
Pin Name
Description
AREF
Analog reference voltage
Receiver Reference Voltage. Normally 1.23 V is selected (in combination with VDDA
= 3.3 V). See Table 2.
CDREF
Carrier detect reference voltage
Carrier Detect Reference voltage. The value should be 85 mV below AREF to set
the carrier detection to a nominal of 100 mVp−p.
RESETB
Reset digital logic
When at logic low (VSS) this input holds all the digital logic in reset. During normal
operation RESETB should be at VDD.
RTSB
Request to send
Active−low input selects the operation of the modulator. TxA is enabled when this
signal is low. This signal must be held high during power−up.
RxA
Analog receive input
Receive Data Demodulator Input. Accepts a HART 1200 / 2200 Hz FSK modulated
waveform as input.
RxAFI
Analog receive comparator input
Positive input of the carrier detect comparator and the receiver filter comparator.
TxD
Digital transmit input
Input to the modulator accepts digital data in NRZ form. When TxD is low, the modulator output frequency is 2200 Hz. When TxD is high, the modulator output frequency
is 1200 Hz.
XIN
Oscillator input
Input to the internal oscillator must be connected to a parallel mode ceramic resonator
when using the internal oscillator or grounded when using an external clock signal.
XOUT
Oscillator output
Output from the internal oscillator must be connected to an external clock signal or to
a parallel mode ceramic resonator when using the internal oscillator.
CLK1
Programmable Clock Output
Output signal derived from oscillator output, frequency division set by internal register.
CLK2
Programmable Clock Output
Output signal derived from oscillator output, frequency division set by internal register.
As this signal is also used internally, the division should be set so that the output frequency is 460.8 kHz
CBIAS
Comparator bias current
Connection to the external bias resistor. RBIAS should be selected such that AREF /
RBIAS = 2.5 mA ± 5 %
CD
Carrier detect output
Output goes high when a valid input is recognized on RxA. If the received signal is
greater than the threshold specified on CDREF for four cycles of the RxA signal, the
valid input is recognized.
RxAF
Analog receive filter output
The output of the three pole high pass receive data filter
RxD
Digital receive output
Signal outputs the digital receive data. When the received signal (RxA) is 1200 Hz,
RxD outputs logic high. When the received signal (RxA) is 2200 Hz, RxD outputs
logic low. The HART receive data stream is only active if Carrier Detect (CD) is high.
RxD_ENH
TxA
Digital receive output, alternative
Analog transmit output
Not(OCD) or RXD
Transmit Data Modulator Output. A trapezoidal shaped waveform with a frequency of
1200 Hz or 2200 Hz corresponding to a data value of 1 or 0 respectively applied to
TxD. TxA is active when RTSB is low. TxA equals 0.5 V when RTSB is high.
SCLK
SPI bus clock line
Serial communication clock line
DATA
SPI bus data line
Serial communication data line. Frames transmitted can either be 8 bit or 16 bit long.
CS
SPI bus chip select
Serial communication chip select line. Pulled high by microcontroller while a frame is
transmitted.
JUMP
DAC Alarm value
When a problem is detected, such as a clock failure or the watchdog going off, the
DAC will jump to VSS or DACREF, depending on whether this pin is connected to
VSS or VDD respectively.
DACREF
DAC Reference
This is the high value of the output and can be connected to any voltage between
AREF and VDD.
DAC
DAC Output
Output of a 16 bit Sigma−Delta Modulator
KICK
Watchdog Kick
Periodically a pulse should be provided to reset the watchdog. This can be configured
in internal registers for an internal 1.8kHz signal, or to an external signal provided to
this pin.
VPOR
POR Input
Input to the POR comparator. The voltage on this pin is compared with AREF. An
external resistor divider should divide the supply voltage to this pin.
VDD
Digital power
Power for the digital modem circuitry
VDDA
Analog supply voltage
Power for the analog modem circuitry
VSS
Ground
Digital ground
VSSA
Analog ground
Analog ground
http://onsemi.com
7
NCN5192
Functional Description
The NCN5192 is a single-chip modem for use in Highway
Addressable Remote Transducer (HART) field instruments
and masters. The modem IC contains a transmit data
modulator with signal shaper, carrier detect circuitry, an
analog receiver, demodulator circuitry and an oscillator, as
shown in the block diagram in Figure 1.
The modulator accepts digital data at its digital input TxD
and generates a trapezoidal shaped FSK modulated signal at
the analog output TxA. A digital “1” or mark is represented
with a frequency of 1200 Hz. A digital “0” or space is
represented with a frequency of 2200 Hz. The used bit rate
is 1200 baud.
The demodulator receives the FSK signal at its analog
input, filters it with a band-pass filter and generates 2 digital
signals: RxD: Received Data and CD: Carrier Detect. At the
digital output RxD the original modulated signal is received.
CD outputs the Carrier Detect signal. It goes logic high if the
received signal is above 100 mVpp during 4 consecutive
carrier periods.
The oscillator provides the modem with a stable time base
using either a simple external resonator or an external clock
source.
The Numeric Controlled Oscillator (NCO) works in a
phase continuous mode preventing abrupt phase shifts when
switching between mark and space frequency. The control
signal “Request To Send” (RTSB) enables the NCO. When
RTSB is logic low the modulator is active and NCN5192 is
in transmit mode. When RTSB is logic high the modulator
is disabled and NCN5192 is in receive mode.
The digital outputs of the NCO are shaped in the Wave
Shaper block to a trapezoidal signal. This circuit controls the
rising and falling edge to be inside the standard HART
waveshape limits. Figure 6 shows the transmit-signal forms
captured at TxA for mark and space frequency. The slew
rates are SRm = 1860 V/s at the mark frequency and SRs =
3300 V/s at the space frequency. For AREF = 1.235 V, TxA
will have a voltage swing from approximately 0.25 to
0.75 VDC.
VTxA
“1” = Mark; fm =1.2 kHz
0.5 V
0.5 V
SRm = 1860 V/s
Detailed Description
0
VTxA
2
“0” = Space; fs =2.2 kHz
Modulator
The modulator accepts digital data in NRZ form at the
TxD input and generates the FSK modulated signal at the
TxA output.
t (ms)
1
0.5 V
0.5 V
t (ms)
SRs = 3300 V/s
TxD
Numeric
Controlled
Oscillator
RTS
0
TxA
Sine
Shaper
FSK_OUT
1
2
KVDE20110408
Figure 6. Modulator shaped output signal for Mark
and Space frequency at TxA pin.
MODULATOR
Demodulator
PC20101117.1
Figure 4. Modulator Block Diagram
The demodulator accepts a FSK signal at the RxA input
and reconstructs the original modulated signal at the RxD
output. Figure 7 illustrates the demodulation process.
A logic “1” or mark is represented by a frequency fm =
1200 Hz. A logic “0”or space is represented by a frequency
fs = 2200 Hz.
FSK_IN
“1” = Mark
1.2 kHz
“0” = Space
2.2 kHz
RxD
LSB
IDLE (mark)
t
MSB
Start
D0
D1
D2
“0”
“1”
“0”
“1”
tBIT
IDLE (mark)
D3
D4
D5
D6
D7
Par
“0”
“0”
“1”
“0”
“1”
“0”
8 data bits
Stop
t BIT
PC20101013.4
Figure 7. Modulation Timing
tBIT = 833 ms
This HART bit stream follows a standard 11-bit UART
frame with Start, Stop, 8 Data – and 1 Parity bit (odd). The
communication speed is 1200 baud.
tBIT = 454 m s
KVDE20110407.5
Figure 5. Modulation Timing
http://onsemi.com
8
NCN5192
Receive Filter and Comparator
high and the next comparator pulse is received in less than
2.5 ms. Once CD goes inactive, it takes four consecutive
pulses out of the comparator to assert CD again. Four
consecutive pulses amount to 3.33 ms when the received
signal is 1200 Hz and to 1.82 ms when the received signal
is 2200 HZ. The difference between RxD and RxD_ENH is
evident when CD is low: RxD is then also low, while
RxD_ENH is then high. When CD is high, RxD and
RxD_ENH have the same output.
The received FSK signal first is filtered using a band-pass
filter build around the low noise receiver operational
amplifier “Rx HP filter”. This filter blocks interferences
outside the HART signal band.
C4
R6
R5
RxAF
RxAFI
PC20101118 .2
HART IN
RxA
R3
C3
C2
Miscellaneous Analog Circuitry
C1
R4
Rx HP Filter
DEMODULATOR
The NCN5192 requires two voltage references, AREF
and CDREF. AREF sets the DC operating point of the
internal operational amplifiers and is the reference for the
Rx comparator. If NCN5192 operates at VDD = 3.3 V the ON
Semiconductor LM285D 1.235 V reference is
recommended.
The level at which CD (Carrier Detect) becomes active is
determined by the DC voltage difference (CDREF - AREF).
Selecting a voltage difference of 80 mV will set the carrier
detect to a nominal 100 mVp-p.
R1
R2
1.235 VDC
AREF
Figure 8. Demodulator Receive Filter and Signal
Comparator
The filter output is fed into the Rx comparator. The
threshold value equals the analog ground making the
comparator to toggle on every zero crossing of the filtered
FSK signal. The maximum demodulator jitter is 12 % of one
bit given the input frequencies are within the HART
specifications, a clock frequency of 460.8 kHz (±1.0 %) and
zero input (RxA) asymmetry.
Bias Current Resistor
The NCN5192 requires a bias current resistor RBIAS to be
connected between CBIAS and VSS. The bias current
controls the operating parameters of the internal operational
amplifiers and comparators and should be set to 2.5 mA.
Carrier Detect Circuitry
Low HART input signal levels increases the risk for the
generation of bit errors. Therefore the minimum signal
amplitude is set to 80−120 mVpp. If the received signal is
below this level the demodulator is disabled.
This level detection is done in the Carrier Detector. The
output of the demodulator is qualified with the carrier detect
signal (CD), therefore, only RxA signals large enough to be
detected (100 mVp-p typically) by the carrier detect circuit
produce received serial data at RxD.
KVDE20110407.6
BIAS
AREF
OPA
FILTERED
HART IN
RxAFI
PC20101118 .4
Demodulator
Logic
Rx Comp
RxD_ENH
CD
Carrier Detect
Counter
DEMODULATOR
CBIAS
RBIAS
15 MW
RxD
2.5 mA
15 MW
Voltage References
Rx Comp
AREF
1.235 VDC
CDREF
Figure 10. Bias Circuit
The value of the bias current resistor is determined by the
reference voltage AREF and the following formula:
V AREF – 80 mV
Carrier Comp
R BIAS + AREF
2.5 mA
Figure 9. Demodulator Carrier and Signal
Comparator
The recommended bias current resistor is 500 KW when
AREF is equal to 1.235 V.
The carrier detect comparator shown in Figure 9 generates
logic low output if the RxAFI voltage is below CDREF. The
comparator output is fed into a carrier detect block. The
carrier detect block drives the carrier detect output pin CD
high if RTSB is high and four consecutive pulses out of the
comparator have arrived. CD stays high as long as RTSB is
Oscillator
The clock signal used by NCN5192 can either be
460.8 kHz, 921.6 kHz or 1.8432 MHz. This can be provided
by an external clock or a resonator or crystal connected to the
internal oscillator.
http://onsemi.com
9
NCN5192
Internal Oscillator Option
Reset
The oscillator cell will function with a 460.8 kHz,
921.6 kHz or 1.8432 MHz crystal or ceramic resonator. A
parallel resonant ceramic resonator can be connected
between XIN and XOUT. Figure 11 illustrates the crystal
option for clock generation using a 460.8 kHz (±1%
tolerance) parallel resonant crystal and two tuning
capacitors Cx. The actual values of the capacitors may
depend on the recommendations of the manufacturer of the
resonator. Typically, capacitors in the range of 100 pF to
470 pF are used. Additionally, a resistor may be required
between XOUT and the crystal terminal, depending on
manufacturer recommendation.
The NCN5192 IC uses CLK2 as clock signal for the wave
shaping and digital logic. This signal must be set 460.8 kHz
by activating the proper frequency division in the internal
register (bit 1 and 2). The CLK1 frequency division (bit 3
and 4) can be freely chosen. This programmable clock signal
can be used to drive other ICs such as a microcontroller and
is not used internally in the NCN5192.
The NCN5192 modem includes a Power on Reset block.
An external resistor division of the supply voltage is
required, and should be tied to pin VPOR. This pin is
attached to an internal comparator, and is compared to the
AREF voltage. When this comparator trips, the RESETB
pin will be pulled low and the IC will reset. After VPOR
returns to a valid level, the RESETB pin will be held low for
at least an additional 35 ms (may be longer depending on
clock frequency). The RESETB pin will also be pulled low
when a microcontroller failure is detected. A watchdog will
guard microcontroller communication by looking at the
KICK pin. When the microcontroller fails to provide a
periodical pulse on this pin, the watchdog will pull down the
RESETB pin for 140 ms. A rising edge should be provided
to the IC at least every 53 ms. A 1.8 kHz kick can also be
provided internally if bit 5 of the internal register is set. If the
watchdog kick is provided internally, the KICK pin should
be tied to Vss.
POR
AREF
VDD
Crystal
Oscillator
OPA
VPOR
XOUT
460.8 kHz
CX
XIN
PC20101118 . 5
KVDE 20110408 .1
CX
Figure 13. Power on Reset Block
Figure 11. Crystal Oscillator
External Clock Option
SCLK
It may be desirable to use an external clock as shown in
Figure 12 rather than the internal oscillator. In addition, the
NCN5192 consumes less current when an external clock is
used. Minimum current consumption occurs with the clock
connected to XOUT and XIN connected to VSS.
CS
DATA
Figure 14. 8 Bit SPI Frame
SCLK
Crystal
Oscillator
XOUT
CS
DATA
XIN
Figure 15. 16 Bit SPI Frame
PC20101118 .6
SPI Communication
460.8 kHz
The SPI bus on the NCN5192 is made up of three signals;
DATA, SCLK, and CS. The data is either 8 bits or 16 bits. In
the case of 8 bits CS will go high for eight clock cycles of
SCLK and in the case of 16 bits CS will be high for 16 clock
cycles of SCLK, as can be seen on Figures 14 and 15.
CS should first go high at least one clock cycle before the
other signals change. One clock cycle is 2.17 ms at a master
Figure 12. Oscillator with External Clock
http://onsemi.com
10
NCN5192
Internal Register
clock frequency of 460.8 kHz. CS is clocked in at the falling
edge of the CLK1 clock to detect if the data is for the mode
register or the DAC.
SCLK can begin to clock in DATA serially to the chip on
the falling edge of SCLK. SCLK should have a maximum
frequency of 460.8 kHz. The format of the data should be
either 8 or 16 bits with the most significant bit first.
DATA is shifted into the chip on the falling edge of SCLK,
and thus for correct operation DATA should change only on
the rising edge of SCLK. The first bit shifted in is the MSB.
If 14 bit DAC communication is utilized, then two 0’s should
precede the 14 bits, and 16 clock cycles on SCLK should
occur. Once the data is shifted in, CS should go low no
sooner than one clock cycle after the last rising edge of
SCLK.
The NCN5192 has an 8 bit register to setup its internal
operation. An 8 bit SPI communication method is used to
write to the mode register. If CS goes low after only 8 clock
cycles of SCLK the Mode register will latch in the 8 bits
which are shifted into the SPI shift register. In Table 9 an
explanation of the usage of each bit is given. All bits are set
to ‘0’ at reset.
Sigma Delta DAC
The NCN5192 Modem has an integrated Sigma−Delta
Modulator for use in a current loop slave transmitter.
Through this DAC, an analog value can be set and
transmitted across the current loop. For more information on
how to create a current loop slave transmitter, see
application notes on the ON Semi website. The DAC output
will switch between 0 V and the voltage provided to
DACREF. To achieve maximum accuracy, the DACREF
voltage should be kept stable, so that power supply
variations are not visible in the DAC output. The
Sigma−Delta modulator output can be set through SPI
frames containing 14 or 16 significant bits. The length of the
data frames can be set through bit 0 is the status register. The
output of the DAC can be set return to zero (RTZ) or
non−RTZ. This is important when the rise and fall time of the
signal are not identical. This will cause a DC offset
depending on the number of rising and falling edges. As the
output bits of a sigma−delta modulator are randomly
arranged (ie. for the same setting we could get 01110000 or
01010100), the number of edges might vary over time for a
non return to zero signal. Setting the DAC to “return to zero”
forces the output to have a rising and falling edge for each
logic “1” bit, so that no offset from pulse asymmetry can
occur. However, this will decrease the range of the
modulator to 50% of DACREF, as the maximum duty cycle
is 50% instead of 100% for NRZ. When a clock failure is
detected, using an internal oscillator, the DAC output will
jump to the level set by the JUMP pin, until the IC is reset
or a rising flank is detected on KICK.
Table 9. INTERNAL REGISTER DESCRIPTION
Bit
Description
0 (LSB)
0 = DAC in 14−bit mode
1 = DAC in 16−bit mode
1
Set the crystal divide so that CLK2 is 460.8 kHz
Bit 2
Bit 1
0
0
Crystal/2
0
1
Crystal/4
1
0
Crystal/1
1
1
Crystal/4
2
3
4
Set the crystal divide for CLK1
Bit 4
Bit 3
0
0
Crystal/2
0
1
Crystal/4
1
0
Crystal/1
1
1
Crystal/4
5
0 = Watchdog kick external (pin)
1 = Watchdog kick internal (1.8 kHz)
6
0 = RTZ output format on DAC
1 = Non RTZ output format on DAC
7 (MSB)
0 = RxD is low when carrier is off
1 = RxD is high when carrier is off
Setting this bit, changes the function of RxD to
the function of RxD_ENH
Table 10. SPI FRAME FORMAT
Description
Bits
Mode Register
8
DAC – 14 bits mode
16
DAC – 16 bits mode
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
Mode Register Data
0
0
DAC Output Word
DAC Output Word
http://onsemi.com
11
1
0
NCN5192
Ordering Information
The NCN5192 is available in a 32−pin no lead quad flat pack (NQFP). Use the following part numbers when ordering.
Contact your local sales representative for more information: www.onsemi.com.
Table 11. ORDERING INFORMATION
Part Number
Package
Shipping Configuration
Temperature Range
NCN5192MNG
32−pin NQFP
Green/RoHS compliant
60 Tube/Tray
−40°C to +85°C (Industrial)
NCN5192MNRG
32−pin NQFP
Green/RoHS compliant
5000 / Tape & Reel
−40°C to +85°C (Industrial)
http://onsemi.com
12
NCN5192
PACKAGE DIMENSIONS
QFN32 5*5*1 0.5 P
CASE 488AM−01
ISSUE O
PIN ONE
LOCATION
2X
ÉÉ
ÉÉ
0.15 C
2X
A
B
D
NOTES:
1. DIMENSIONS AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.25 AND 0.30 MM TERMINAL
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
E
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
TOP VIEW
0.15 C
(A3)
0.10 C
A
32 X
0.08 C
C
L
32 X
9
D2
SEATING
PLANE
A1
SIDE VIEW
SOLDERING FOOTPRINT*
EXPOSED PAD
16
5.30
K
32 X
17
MILLIMETERS
MIN
NOM MAX
0.800 0.900 1.000
0.000 0.025 0.050
0.200 REF
0.180 0.250 0.300
5.00 BSC
2.950 3.100 3.250
5.00 BSC
2.950 3.100 3.250
0.500 BSC
0.200
−−−
−−−
0.300 0.400 0.500
3.20
8
32 X
0.63
E2
1
24
32
3.20
25
b
0.10 C A B
32 X
5.30
e
0.05 C
32 X
0.28
BOTTOM VIEW
28 X
0.50 PITCH
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
13
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCN5192/D