NCT203 D

NCT203
Low Voltage, High
Accuracy Temperature
Monitor with I2C Interface
The NCT203 is a digital thermometer and undertemperature/
overtemperature alarm, intended for use in thermal management
systems requiring low power and size. The NCT203 operates over a
supply range of 1.4 V to 2.75 V making it possible to use it in a wide
range of applications including low power devices.
The NCT203 can measure the ambient temperature accurate to
±1.75°C. The device operates over a wide temperature range of −40 to
+125°C.
The NCT203 has a configurable ALERT output and over−
temperature shutdown THERM pin.
Communication with the NCT203 is accomplished via the I2C
interface which is compatible with industry standard protocols.
Through this interface the NCT203s internal registers may be
accessed. These registers allow the user to read the current
temperature, change the configuration settings and adjust limits.
An ALERT output signals when the on−chip temperature is out of
range. The THERM output is a comparator output that can be used to
shut down the system if it exceeds the programmed limit. The ALERT
output can be reconfigured as a second THERM output, if required.
http://onsemi.com
DFN8
MT SUFFIX
CASE 511BU
PIN ASSIGNMENTS
VDD
1
8
SCL
NC
2
7
SDA
NC
3
6
ALERT/THERM2
THERM
4
5
GND
DFN
(Top View)
Features
•
•
•
•
•
•
•
•
•
Small DFN Package
On−Chip Temperature Sensor
Low Voltage Operation: 1.4 V to 2.75 V
Low Quiescent Current:
♦ 44 mA Normal Mode (max)
♦ 20 mA Shutdown (max)
Power Saving Shutdown Mode
Operating Temperature Range of −40°C to 125°C
2−wire I2C Serial Interface
Programmable Over/Undertemperature Limits
This is a Pb−Free Device
MARKING DIAGRAM
1
J2
M
G
J2 MG
G
= Specific Device Code
= Date Code
= Pb−Free Device
(*Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 13 of this data sheet.
Applications
• Smart Phones, Tablet PCs, Satellite Navigation, Smart Batteries
© Semiconductor Components Industries, LLC, 2013
June, 2013 − Rev. 2
1
Publication Order Number:
NCT203/D
NCT203
CONVERSION RATE
REGISTER
TEMPERATURE
LOW−LIMIT REGISTER
RUN/
STANDBY
DIGITAL MUX
LIMIT
COMPARATOR
A−TO−D
CONVERTER
TEMPERATURE
VALUE REGISTER
BUSY
TEMPERATURE
HIGH−LIMIT REGISTER
TEMPERATURE THERM
LIMIT
HYSTERESIS
REGISTER
ADDRESS POINTER
REGISTER
CONFIGURATION
REGISTERS
ON−CHIP
TEMPERATURE
SENSOR
INTERRUPT
MASKING
STATUS REGISTER
NCT203
6
4
ALERT/
THERM2
THERM
I2C INTERFACE
1
VDD
5
7
SDA
GND
8
SCL
Figure 1. Functional Block Diagram
VDD
VDD
1.4V TO 2.75V
NCT203
0.1 μF
TYP 10 kW
SCL
VDD
SDA
TYP 10 kW
OVERTEMPERATURE
SHUTDOWN
I2C Master
ALERT/
THERM2
THERM
GND
Figure 2. Typical Application Circuit
Table 1. PIN FUNCTION DESCRIPTION − DFN PACKAGE
Pin No.
Pin Name
Description
1
VDD
Positive Supply, 1.4 V to 2.75 V
2
NC
No connect − leave this pin floating.
3
NC
No connect − leave this pin floating.
4
THERM
Open−Drain Output. Can be used to throttle a CPU clock in the event of an overtemperature condition. Requires pullup resistor to VDD. Active low output.
5
GND
6
ALERT/THERM2
Supply Ground Connection.
7
SDA
Logic Input/Output, I2C Serial Data. Requires pullup resistor to VDD.
8
SCL
Logic Input, I2C serial clock. Requires pullup resistor to VDD.
Open−Drain Logic Output used as Interrupt. This can also be configured as a second THERM output. Requires pullup resistor to VDD. Active low output.
http://onsemi.com
2
NCT203
Table 2. ABSOLUTE MAXIMUM RATINGS (Note 1)
Rating
Symbol
Value
Unit
VDD
−0.3, +3
V
−0.3 to +5.25
V
−1, +50
mA
Supply Voltage (VDD) to GND
SCL, SDA, ALERT, THERM
Input current on SDA, THERM
IIN
Maximum Junction Temperature
TJ(max)
150.7
°C
Operating Temperature Range
TOP
−40 to 125
°C
Storage Temperature Range
TSTG
−65 to 160
°C
ESD Capability, Human Body Model (Note 2)
ESDHBM
2000
V
ESD Capability, Machine Model (Note 2)
ESDMM
100
V
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
2. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per AEC−Q100-002 (EIA/JESD22-A114)
ESD Machine Model tested per AEC-Q100-003 (EIA/JESD22-A115)
Table 3. I2C TIMING − 400 kHz
Parameter (Note 3)
Symbol
Min
Clock Frequency
fSCLK
10
Clock Period
tSCLK
2.5
ms
SCL High Time
tHIGH
0.6
ms
SCL Low Time
tLOW
1.3
ms
Start Setup Time
tSU;STA
0.6
ms
Start Hold Time (Note 4)
tHD;STA
0.6
ms
Data Setup Time (Note 5)
tSU;DAT
100
ns
Data Hold Time (Note 6)
tHD;DAT
0.9
ms
SCL, SDA Rise Time
tr
300
ns
SCL, SDA Fall Time
tf
300
ns
Stop Setup Time
3.
4.
5.
6.
tSU;STO
0.6
Bus Free Time
tBUF
1.3
Glitch Immunity
tSW
Typ
Max
Unit
400
kHz
ms
ms
50
ns
Guaranteed by design, but not production tested.
Time from 10% of SDA to 90% of SCL.
Time for 10% or 90% of SDA to 10% of SCL.
A device must internally provide a hold time of at least 300 ns for the SDA signal to bridge the undefined region of the falling edge of SCL.
tR
tLOW
tF
tHD;STA
SCLK
tHIGH
tHD;STA
tHD;DAT
tSU;STA
tSU;STO
tSU;DAT
SDATA
tBUF
STOP START
START
Figure 3. I2C Timing Diagram
http://onsemi.com
3
STOP
NCT203
Table 4. ELECTRICAL CHARACTERISTICS
(TA = TMIN to TMAX, VDD = 1.6 V to 2.75 V. All specifications for −40°C to +125°C, unless otherwise noted.)
Test Conditions
Parameter
Min
Typ
Max
Unit
+125
°C
±1.75
±3
°C
1.5
°C
TEMPERATURE SENSOR
−40
Measurement Range
TEMPERATURE SENSOR ACCURACY
VDD
TA = 25°C to 85°C
TA = −40°C to +125°C
VDD = 1.8 V, TA = 40°C to +100°C
−0.5
ADC Resolution
10
Bits
Conversion time
60
ms
Temperature Resolution
1
°C
Undervoltage Lockout Threshold
1.32
V
Power−On Reset Threshold
0.9
V
POWER REQUIREMENTS
1.4
Supply Voltage
Quiescent Current (IDD)
Standby Current (ISTBY)
I2C inactive – 0.0625
Conversions/Sec Rate, 1.8 V VDD
I2C active, 400 kHz
15
I2C inactive
I2C active, 400 kHz
1
10
2.75
V
44
mA
20
mA
30
DIGITAL INPUT/OUTPUT
Input Logic Levels
VIH
0.7 x VDD
2.75
V
VIL
−0.5
0.3 x VDD
V
Input Current
0 < VIN < 2.75 V
1
mA
Output Logic Levels
VOL SDA, ALERT, THERM
VDD > 2 V, IOL = 3 mA
0
0.4
V
VDD < 2 V, IOL = 3 mA
0
0.2 x VDD
V
http://onsemi.com
4
NCT203
Theory of Operation
measurement. To reduce the effects of noise, digital filtering
is performed by averaging the results of 16 measurement
cycles for low conversion rates. At rates of 16−, 32− and 64−
conversions/second, no digital averaging occurs. Signal
conditioning and measurement of the internal temperature
sensor are performed in the same manner.
The NCT203 is an on−chip temperature sensor and
over/under temperature alarm. When the NCT203 is
operating normally, the on−board ADC operates in a free
running mode. The ADC digitizes the signals from the
temperature sensor and the results are stored in the
temperature value register.
The measurement results are compared with the
corresponding high, low, and THERM temperature limits,
stored in the on−chip registers. Out−of−limit comparisons
generate flags that are stored in the status register. A result
that exceeds the high temperature limit or the low
temperature limit causes the ALERT output to assert.
Exceeding the THERM temperature limits causes the
THERM output to assert low. The ALERT output can be
reprogrammed as a second THERM output.
The limit registers are programmed and the device
controlled and configured via the serial I2C. The contents of
any register are also read back via the I2C. Control and
configuration functions consist of switching the device
between normal operation and standby mode, selecting the
temperature measurement range, masking or enabling the
ALERT output, switching Pin 6 between ALERT and
THERM2, and selecting the conversion rate.
Temperature Measurement Results
The results of the temperature measurement are stored in
the temperature value register and compared with limits
programmed into the high and low limit registers.
The temperature value is in Register 0x00 and has a
resolution of 1°C.
Temperature Measurement Range
The temperature measurement range is, by default, 0°C to
+127°C. However, the NCT203 can be operated using an
extended temperature range. The extended measurement
range is −64°C to +191°C. Therefore, the NCT203 can be
used to measure the full temperature range of the NCT203,
from −40°C to +125°C.
The extended temperature range is selected by setting
Bit 2 of the configuration register to 1. The temperature
range is 0°C to 127°C when Bit 2 equals 0. A valid result is
available in the next measurement cycle after changing the
temperature range.
In extended temperature mode, the upper and lower
temperature that can be measured by the NCT203 is limited
by the device temperature range of −40°C to +125°C. The
temperature register can have values from −64°C to +191°C.
It should be noted that although temperature
measurements can be made while the part is in extended
temperature mode, the NCT203 should not be exposed to
temperatures greater than those specified in the absolute
maximum ratings section. Further, the device is only
guaranteed to operate as specified at ambient temperatures
from −40°C to +125°C.
Temperature Measurement Method
A simple method of measuring temperature is to exploit
the negative temperature coefficient of a diode, measuring
the base emitter voltage (VBE) of a transistor operated at
constant current. However, this technique requires
calibration to null the effect of the absolute value of VBE,
which varies from device to device.
The technique used in the NCT203 measures the change
in VBE when the device operates at different currents.
To measure DVBE, the operating current through the
sensor is switched among related currents. N1 x I and N2 x I
are different multiples of the current, I. The currents through
the temperature diode are switched between I and N1 x I,
giving DVBE1; and then between I and N2 x I, giving DVBE2.
The temperature is then calculated using the two DVBE
measurements.
The resulting DVBE waveforms are passed through a
65 kHz low−pass filter to remove noise and then to a
chopper−stabilized amplifier. This amplifies and rectifies
the waveform to produce a dc voltage proportional to DVBE.
The ADC digitizes this voltage producing a temperature
Temperature Data Format
The NCT203 has two temperature data formats. When the
temperature measurement range is from 0°C to 127°C
(default), the temperature data format for temperature
results is binary. When the measurement range is in
extended mode, an offset binary data format is used.
Temperature values are offset by 64°C in the offset binary
data format. Examples of temperatures in both data formats
are shown in Table 5.
http://onsemi.com
5
NCT203
Temperature Value Register
Table 5. TEMPERATURE DATA FORMAT
Temperature
Binary
Offset Binary
(Note 1)
-55°C
0 000 0000 (Note 2)
0 000 1001
0°C
0 000 0000
0 100 0000
+1°C
0 000 0001
0 100 0001
+10°C
0 000 1010
0 100 1010
+25°C
0 001 1001
0 101 1001
+50°C
0 011 0010
0 111 0010
+75°C
0 100 1011
1 000 1011
+100°C
0 110 0100
1 010 0100
+125°C
0 111 1101
1 011 1101
+127°C
0 111 1111
1 011 1111
+150°C
0 111 1111 (Note 3)
1 101 0110
The NCT203 has a temperature register to store the results
of temperature measurement. This register can only be
written to by the ADC and can be read by the user over the
I2C. The temperature value register is at Address 0x00.
The power−on default for this register is 0x00.
Configuration Register
The configuration register is Address 0x03 at read and
Address 0x09 at write. Its power−on default is 0x00. Only
four bits of the configuration register are used. Bit 0, Bit 1,
Bit 3, and Bit 4 are reserved; only zeros should be written to
these.
Bit 7 of the configuration register masks the ALERT
output. If Bit 7 is 0, the ALERT output is enabled. This is the
power−on default. It Bit 7 is set to 1, the ALERT output is
disabled. This applies only if Pin 6 is configured as ALERT.
If Pin 6 is configured as THERM2, then the value of Bit 7
has no effect.
If Bit 6 is set to 0, which is power−on default, the device
is in operating mode with ADC converting. If Bit 6 is set to
1, the device is in standby mode and the ADC does not
convert. The I2C does, however, remain active in standby
mode; therefore, values can be read from or written to the
NCT203 via the I2C. The ALERT and THERM output are
also active in standby mode. Changes made to the register in
standby mode that affect the THERM or ALERT outputs
cause these signals to be updated.
Bit 5 determines the configuration of Pin 6 on the
NCT203. If Bit 5 is 0 (default), then Pin 6 is configured as
a ALERT output. If Bit 5 is 1, then Pin 6 is configured as a
THERM2 output. Bit 7, the ALERT mask bit, is only active
when Pin 6 is configured as an ALERT output. If Pin 6 is set
up as a THERM2 output, then Bit 7 has no effect.
Bit 2 sets the temperature measurement range. If Bit 2 is
0 (default value), the temperature measurement range is set
between 0°C to +127°C. Setting Bit 2 to 1 sets the
measurement range to the extended temperature range
(−64°C to +191°C).
1. Offset binary scale temperature values are offset by
64°C.
2. Binary scale temperature measurement returns 0°C for all
temperatures < 0°C.
3. Binary scale temperature measurement returns 127°C for
all temperatures > 127°C.
The user can switch between measurement ranges at any
time. Switching the range likewise switches the data format.
The next temperature result following the switching is
reported back to the register in the new format. However, the
contents of the limit registers do not change. It is up to the
user to ensure that when the data format changes, the limit
registers are reprogrammed as necessary. More information
on this is found in the Limit Registers section.
NCT203 Registers
The NCT203 contains 12, 8−bit registers in total. These
registers store the results of the temperature measurement,
high and low temperature limits, and configure and control
the device. See the Address Pointer Register section through
the Consecutive ALERT Register section of this data sheet
for more information on the NCT203 registers. Additional
details are shown in Table 6 through Table 9. The entire
register map is available in Table 10.
Table 6. CONFIGURATION REGISTER BIT
ASSIGNMENTS
Address Pointer Register
The address pointer register itself does not have, nor does
it require, an address because the first byte of every write
operation is automatically written to this register. The data
in this first byte always contains the address of another
register on the NCT203 that is stored in the address pointer
register. It is to this register address that the second byte of
a write operation is written, or to which a subsequent read
operation is performed.
The power−on default value of the address pointer register
is 0x00. Therefore, if a read operation is performed
immediately after power−on, without first writing to the
address pointer, the value of the temperature is returned
because its register address is 0x00.
Name
Function
7
MASK1
0 = ALERT Enabled
1 = ALERT Masked
0
6
RUN/STOP
0 = Run
1 = Standby
0
5
ALERT/
THERM2
0 = ALERT
1 = THERM2
0
4, 3
Reserved
2
Temperature
Range Select
1, 0
Reserved
http://onsemi.com
6
Power−On
Default
Bit
0
0 = 0°C to 127°C
1 = Extended Range
0
0
NCT203
Conversion Rate Register
provided which applies to both THERM channels. This
hysteresis value can be reprogrammed to any value after
powerup (Register Address 0x21).
It is important to remember that the temperature limits
data format is the same as the temperature measurement data
format. Therefore, if the temperature measurement uses
default binary, then the temperature limits also use the
binary scale. If the temperature measurement scale is
switched, however, the temperature limits do not
automatically switch. The user must reprogram the limit
registers to the desired value in the correct data format. For
example, if the low limit is set at 10°C with the default binary
scale, the limit register value is 0000 1010b. If the scale is
switched to offset binary, the value in the low temperature
limit register needs to be reprogrammed to 0100 1010b.
The conversion rate register is Address 0x04 at read and
Address 0x0A at write. The lowest four bits of this register are
used to program the conversion rate by dividing the internal
oscillator clock by 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024
to give conversion times from 15.5 ms (Code 0x0A) to 16
seconds (Code 0x00). For example, a conversion rate of
eight conversions per second means that beginning at
125 ms intervals, the device performs a conversion on the
internal temperature channel.
The conversion rate register can be written to and read
back over the I2C. The higher four bits of this register are
unused and must be set to 0. The default value of this register
is 0x08, giving a rate of 16 conversions per second. Use of
slower conversion times greatly reduces the device power
consumption.
Status Register
Table 7. CONVERSION RATES
Code
Conversion/Second
Time (Seconds)
0x00
0.0625
16
0x01
0.125
8
0x02
0.25
4
0x03
0.5
2
0x04
1
1
0x05
2
500 m
0x06
4
250 m
0x07
8
125 m
0x08
16
62.5 m
0x09
32
31.25 m
0x0A
64
15.5 m
0x0B to 0xFF
Reserved
The status register is a read−only register at Address 0x02.
It contains status information for the NCT203. When Bit 7
of the status register is high, it indicates that the ADC is bisy
converting. The other bits in this register flag the
out−of−limit temperature measurements (Bit 6 to Bit 3, and
Bit 1 to Bit 0).
If Pin 6 is configured as an ALERT output, the following
applies: If the temperature measurement exceeds its limits,
Bit 6 (high limit) or Bit 5 (low limit) of the status register
asserts to flag this condition. These flags are NOR’ed
together, so if any of them is high, the ALERT interrupt latch
is set and the ALERT output goes low.
Reading the status register clears the flags, Bit 6 to Bit 2,
provided the error conditions causing the flags to be set have
gone away. A flag bit can be reset only if the corresponding
value register contains an in−limit measurement or if the
sensor is good.
The ALERT interrupt latch (output) is reset by either
reading the status register or by issuing the device with an
ARA. In order for either of the above to work the error
condition must have gone away.
When Flag 0 is set, the THERM output goes low to
indicate that the temperature measurement is outside the
programmed limits. The THERM output does not need to be
reset, unlike the ALERT output. Once the measurements are
within the limits, the corresponding status register bits are
automatically reset and the THERM output goes high. The
user may add hysteresis by programming Register 0x21. The
THERM output is reset only when the temperature falls to
limit value minus the hysteresis value.
When Pin 6 is configured as THERM2, only the high
temperature limits are relevant. If Flag 6 is set, the THERM2
output goes low to indicate that the temperature
measurement is outside the programmed limits. Flag 5 has
no effect on THERM2. The behavior of THERM2 is
otherwise the same as THERM.
Limit Registers
The NCT203 has three limit registers: high, low, and
THERM temperature limits for temperature measurements.
There is also a THERM hysteresis register. All limit
registers can be written to, and read byck over I2C. See
Table 9 for details of the limit register addresses and their
power−on default values.
When Pin 6 is configured as an ALERT output, the high
limit registers perform a > comparison, while the low limit
registers perform a ≤ comparison. For example, if the high
limit register is programmed with 80°C, then measuring
81°C results in an out−of−limit condition, setting a flag in
the status register. If the low limit register is programmed
with 0°C, measuring 0°C or lower resutls in an out−of−limit
condition.
Exceeding the THERM limit asserts THERM low. When
Pin 6 is configured as THERM2, exceeding the high limit
asserts THERM2 low. A default hysteresis value of 10°C is
http://onsemi.com
7
NCT203
Consecutive ALERT Register
Table 8. STATUS REGISTER BIT ASSIGNMENTS
Bit
Name
7
BUSY
6
HIGH
(Note 4)
1 when high temperature limit is
tripped
5
LOW
(Note 4)
1 when low temperature limit is tripped
4
Reserved
3
Reserved
2
Reserved
1
Reserved
0
THRM
The value written to this register determines how many
out−of−limit measurements must occur before an ALERT is
generated. The default value is that one out−of−limit
measurement generates an ALERT. The maximum value
that can be chosen is 4. The purpose of this register is to
allow the user to perform some filtering of the output. This
is particularly useful at the fastest three conversion rates,
where no averaging takes place. This register is at Address
0x22.
Function
1 when ADC is converting
Table 9. CONSECUTIVE ALERT REGISTER CODES
1 when THERM limit is tripped
Register Value
Number of Out-of-Limit
Measurements Required
yxxx 000x
1
yxxx 001x
2
yxxx 011x
3
yxxx 111x
4
4. These flags stay high until the status register is read or
they are reset by POR unless Pin 6 is configured as
THERM2. Then, only Bit 2 remains high until the status
register is read or is reset by POR.
One−Shot Register
The one−shot register is used to initiate a conversion and
comparison cycle when the NCT203 is in standby mode,
after which the device returns to standby. Writing to the
one−shot register address (0x0F) causes the NCT203 to
perform a conversion and comparison on the temperature.
This is not a data register as such, and it is the write operation
to Address 0x0F that causes the one−shot conversion. The
data written to this address is irrelevant and is not stored.
Note: x = don’t care bits, and y = Bus timeout bit.
Default = 0. See interface section for more information.
Table 10. LIST OF REGISTERS
Read Address (Hex)
Write Address (Hex)
Name
Power−On Default
Not Applicable
Not Applicable
Address Pointer
00
Not Applicable
Temperature Value
02
Not Applicable
Status
03
09
Configuration
0000 0000 (0x00)
04
0A
Conversion Rate
0000 1000 (0x08)
05
0B
Temperature High Limit
0101 0101 (0x55) (85°C)
06
0C
Temperature Low Limit
0000 0000 (0x00) (0°C)
Not Applicable
0F (Note 1)
20
20
THERM Limit
21
21
THERM Hysteresis
0000 1010 (0x0A) (0x10°C)
22
22
Consecutive ALERT
0000 0001 (0x01)
FE
Not Applicable
Manufacturer ID
0001 1010 (0x1A)
FF
Not Applicable
Die Revision Code
Undefined
0000 0000 (0x00)
Undefined
One−Shot
http://onsemi.com
8
0101 0101 (0x55) (85°C)
0xXX
NCT203
SERIAL INTERFACE
Control of the NCT203 is carried out via the I2C
compatible serial interface. The NCT203 is connected to this
bus as a slave device, under the control of a master device.
The NCT203 has a bus timeout feature. When this is
enabled, the bus times out after typically 25 ms of no
activity. After this time, the NCT203 resets the SDA line
back to its idle state (high impedance) and waits for the next
start condition. However, this feature is not enabled by
default. Bit 7 of the consecutive alert register (Address =
0x22) should be set to enable it.
mode, the master overrides the acknowledge bit by
pulling the data line high during the low period
before the ninth clock pulse. This is known as no
acknowledge. The master takes the data line low
during the low period before the tenth clock pulse,
then high during the tenth clock pulse to assert a
stop condition.
To write data to one of the device data registers, or to read
data from it, the address pointer register must be set so that
the correct data register is addressed. The first byte of a write
operation always contains a valid address that is stored in the
address pointer register. If data is to be written to the device,
the write operation contains a second data byte that is written
to the register selected by the address pointer register.
This procedure is illustrated in Figure 4. The device
address is sent over the bus followed by R/W set to 0. Thisis
followed by two data bytes. The first data byte is the address
of the internal data register to be written to, which is stored
in the address pointer register. The second data byte is the
data to be written to the internal data register.
When reading data from a register there are two
possibilities.
• If the address pointer register value of the NCT203 is
unknown or not the desired value, it is first necessary to
set it to the correct value before data can be read from
the desired data register. This is done by writing to the
NCT203 as before, but only the data byte containing
the register read address is sent, because data is not to
be written to the register see Figure 4.
A read operation is then performed consisting of the
serial bus address, R/W bit set to 1, followed by the
data byte read from the data register see Figure 6.
• If the address pointer register is known to be at the
desired address, data can be read from the
corresponding data register without first writing to the
address pointer register and the bus transaction shown
in Figure 5 can be omitted.
Addressing the Device
In general, every I2C device has a 7−bit device address,
except for some devices that have extended 10−bit
addresses. When the master device sends a device address
over the bus, the slave device with that address responds.
The NCT203 is available with one device address, 0x4C. For
systems requiring more than one NCT203, another address
option will be required. Please contact your local
ON Semiconductor representative for more information.
The serial bus protocol operates as follows:
1. The master initiates data transfer by establishing a
start condition, defined as a high to low transition
on the serial data line SDA, while the serial clock
line SCL remains high. This indicates that an
address/data stream is going to follow. All slave
peripherals connected to the serial bus respond to
the start condition and shift in the next eight bits,
consisting of a 7−bit address (MSB first) plus a
read/write (R/W) bit, which deternimes the
direction of the data transfer i.e. whether data is
written to, or read from, the slave device. The
peripheral with the address corresponding to the
transmitted address responds by pulling the data
line low during the low period before the ninth
clock pulse, known as the acknowledge bit. All
other devices on the bus now remain idle while the
selected device waits for data to be read from or
written to it. If the R/W bit is a zero then the
master writes to the slave device. If the R/W bit is
a one then the master reads from the slave device.
2. Data is sent over the serial bus in sequences of
nine clock pulses, eight bits of data followed by an
acknowledge bit from the receiver of data.
Transitions on the data line must occur during the
low period of the clock signal and remain stable
during the high period, since a low−to−high
transition when the clock is high can be interpreted
as a stop signal.
3. When all data bytes have been read or written,
stop conditions are established. In write mode, the
master pulls the data line high during the tenth
clock pulse to assert a stop condition. In read
Notes:
• It is possible to read a data byte from a data register
•
without first writing to the address pointer register.
However, if the address pointer register is already at the
correct value, it is not possible to write data to a register
without writing to the address pointer register because
the first data byte of a write is always written to the
address pointer register.
Some of the registers have different addresses for read
and write operations. The write address of a register
must be written to the address pointer if data is to be
written to that register, but it may not be possible to
read data from that address. The read address of a
register must be written to the address pointer before
data can be read from that register.
http://onsemi.com
9
NCT203
1
9
1
9
SCL
SDA
A6
A5
A4
A3
A2
A1
A0
D7
R/W
START BY
MASTER
D6
D5
ACK. BY
NCT203
FRAME 1
SERIAL BUS ADDRESS BYTE
D4
D3
D2
D1
D0
STOP BY
MASTER
ACK. BY
NCT203
FRAME 2
ADDRESS POINTER REGISTER BYTE
Figure 4. Writing to the Address Pointer Register
1
9
1
9
SCL
SDA
A6
A5
A4
A3
A2
A1
A0
D7
R/W
D6
D5
D4
D3
D2
D1
D0
ACK. BY
NCT203
START BY
MASTER
FRAME 1
SERIAL BUS ADDRESS BYTE
ACK. BY
NCT203
FRAME 2
ADDRESS POINTER REGISTER BYTE
1
9
SCL (CONTINUED)
D7
SDA (CONTINUED)
D6
D5
D4
D3
D2
D1
D0
ACK. BY
NCT203
FRAME 3
DATA BYTE
STOP BY
MASTER
Figure 5. Writing a Register Address to the Address Pointer Register,
then Writing a Single Byte of Data to a Register
1
9
1
9
SCL
SDA
START BY
MASTER
A6
A5
A4
A3
A2
A1
A0
D7
R/W
D6
ACK. BY
NCT203
D5
D4
D3
D2
D1
FRAME 2
DATA BYTE FROM REGISTER
FRAME 1
SERIAL BUS ADDRESS BYTE
D0
NO ACK. BY
MASTER
STOP BY
MASTER
Figure 6. Reading a Byte of Data from a Register
ALERT Output
MASTER RECEIVES SMBALERT
This is applicable when Pin 6 is configured as an ALERT
output. The ALERT output goes low whenever an
out−of−limit measurement is detected. It is an open−drain
output and requires a pullup resistor to VDD. Several
ALERT outputs can be wire−OR’ed together, so that the
common line goes low if one or more of the ALERT outputs
goes low.
The ALERT output can be used as an interrupt signal to a
processor, or as an SMBALERT. Slave devices on the bus
cannot normally signal to the bus master that they want to
talk, but the SMBALERT function allows them to do so.
One or more ALERT outputs can be connected to a
common SMBALERT line that is connected to the master.
When the SMBALERT line is pulled low by one of the
devices, the following procedure occurs (see Figure 7):
START
ALERT RESPONSE
ADDRESS
MASTER SENDS
ARA AND READ
COMMAND
RD ACK
DEVICE
ADDRESS
NO
STOP
ACK
DEVICE SENDS
ITS ADDRESS
Figure 7. Use of SMBALERT
1. SMBALERT is pulled low.
2. Master initiates a read operation and sends the
alert response address (ARA = 0001 100). This is
a general call address that must not be used as a
specific device address.
3. The device whose ALERT output is low responds
to the alert response address and the master reads
its device address. As the device address is seven
bits, an LSB of 1 is added. The address of the
device is now known and it can be interrogated in
the usual way.
4. If more than one device’s ALERT output is low,
the one with the lowest device address takes
http://onsemi.com
10
NCT203
where the temperature hovers around the THERM limit, and
the fan is constantly switched.
priority, in accordance with normal bus arbitration.
Once the NCT203 has responded to the alert
response address, it resets its ALERT output,
provided that the error condition that caused the
ALERT no longer exists. If the SMBALERT line
remains low, the master sends the ARA again, and
so on until all devices whose ALERT outputs were
low have responded.
Table 11. THERM HYSTERESIS
Low Power Standby Mode
THERM Hysteresis
Binary Representation
0°C
0 000 0000
1°C
0 000 0001
10°C
0 000 1010
Figure 8 shows how the THERM and ALERT outputs
operate. The ALERT output can be used as a SMBALERT
to signal to the host via the I2C that the temperature has risen.
The user can use the THERM output to turn on a fan to cool
the system, if the temperature continues to increase. This
method ensures that there is a fail−safe mechanism to cool
the system, without the need for host intervention.
The NCT203 can be put into low power standby mode by
setting Bit 6 of the configuration register. When Bit 6 is low,
the NCT203 operates normally. When Bit 6 is high, the ADC
is inhibited, and any conversion in progress is terminated
without writing the result to the corresponding value
register. However, the I2C is still enabled. Power
consumption in the standby mode is reduced to 15 mA if
there is no bus activity.
When the device is in standby mode, it is possible to
initiate a one−shot conversion by writing to the one−shot
register (Address 0x0F), after which the device returns to
standby. It does not matter what is written to the one−shot
register, all data written to it is ignored. It is also possible to
write new values to the limit register while in standby mode.
If the value stored in the temperature value register is outside
the new limits, an ALERT is generated, even though the
NCT203 is still in standby.
TEMPERATURE
1005C
905C
THERM LIMIT
805C
THERM LIMIT − HYSTERESIS
705C
HIGH TEMP LIMIT
605C
505C
405C
RESET BY MASTER
ALERT
The NCT203 Interrupt System
1
4
THERM
The NCT203 has two interrupt outputs, ALERT and
THERM. Both have different functions and behavior.
ALERT is maskable and responds to violations of software
programmed temperature limits. THERM is intended as a
fail−safe interrupt output that cannot be masked.
If the temperature exceeds the programmed high
temperature limits, or equals or exceeds the low temperature
limits, the ALERT output is asserted low. ALERT is reset
when serviced by a master reading its device address,
provided the error condition has gone away and the status
register has been reset.
The THERM output asserts low if the temperature
exceeds the programmed THERM limits. THERM
temperature limits should normally be equal to or greater
than the high temperature limits. THERM is reset
automatically when the temperature falls back within the
THERM limit. A hysteresis value can be programmed; in
which case, THERM resets when the temperature falls to the
limit value minus the hysteresis value. The power−on
hysteresis default value is 10°C, but this can be
reprogrammed to any value after powerup.
The hysteresis loop on the THERM outputs is useful when
THERM is used, for example, as an on/off controller for a
fan. The user’s system can be set up so that when THERM
asserts, a fan is switched on to cool the system. When
THERM goes high again, the fan can be switched off.
Programming a hysteresis value protects from fan jitter,
2
3
Figure 8. Operation of the ALERT and THERM
Interrupts
• If the measured temperature exceeds the high
temperature limit, the ALERT output asserts low.
• If the temperature continues to increase and exceeds the
THERM limit, the THERM output asserts low. This can
be used to throttle the CPU clock or switch on a fan.
• The THERM output deasserts (goes high) when the
temperature falls to THERM limit minus hysteresis.
The default hysteresis value is 10°C.
• The ALERT output deasserts only when the
temperature has fallen below the high temperature
limit, and the master has read the device address and
cleared the status register.
• Pin 6 on the NCT203 can be configured as either an
ALERT output or as an additional THERM output.
• THERM2 asserts low when the temperature exceeds the
programmed high temperature limits. It is reset in the
same manner as THERM and is not maskable.
• The programmed hysteresis value also applies to
THERM2.
Figure 9 shows how THERM and THERM2 operate
together to implement two methods of cooling the system.
http://onsemi.com
11
NCT203
• When the THERM2 limit is exceeded, the THERM2
In this example, the THERM2 limits are set lower than the
THERM limits. The THERM2 output is used to turn on a
fan. If the temperature continues to rise and exceeds the
THERM limits, the THERM output provides additional
cooling by throttling the CPU.
•
•
TEMPERATURE
905C
THERM LIMIT
•
805C
705C
605C
THERM2 LIMIT
505C
Power Supply Rise Time
405C
When powering up the NCT203 you must ensure that the
power supply voltage rises above 1.32 in less than 5 ms. If
a rise time of longer than this occurs then power-on-reset
will be caused and yield unpredictable results.
305C
THERM2
THERM
signal asserts low.
If the temperature continues to increase and exceeds the
THERM limit, the THERM output asserts low.
The THERM output deasserts (goes high) when the
temperature falls to THERM limit minus hysteresis. In
Figure 9, there is no hysteresis value shown.
As the system cools further, and the temperature falls
below the THERM2 limit, the THERM2 signal resets.
Again, no hysteresis value is shown for THERM2.
1
4
2
3
Figure 9. Operation of the THERM and THERM2
Interrupts
http://onsemi.com
12
NCT203
Table 12. ORDERING INFORMATION
Device Number
NCT203MTR2G
Package
Shipping†
DFN8
(Pb−Free)
3000 / Tape and Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
PACKAGE DIMENSIONS
WDFN8 2x1.8, 0.5P
CASE 511BU
ISSUE O
D
PIN ONE
REFERENCE
2X
0.10 C
2X
ÍÍ
ÍÍ
ÍÍ
0.10 C
L
A
B
L1
DETAIL A
E
ALTERNATE TERMINAL
CONSTRUCTIONS
EXPOSED Cu
DETAIL B
A
NOTE 4
MOLD CMPD
DETAIL B
ALTERNATE
CONSTRUCTIONS
A1
A3
SIDE VIEW
e/2
C
SEATING
PLANE
e
7X
4
MILLIMETERS
MIN
MAX
0.70
0.80
0.00
0.05
0.20 REF
0.20
0.30
2.00 BSC
1.80 BSC
0.50 BSC
0.45
0.55
--0.15
0.55
0.65
RECOMMENDED
SOLDERING FOOTPRINT*
7X
DETAIL A
1
DIM
A
A1
A3
b
D
E
e
L
L1
L2
ÉÉÉ
ÉÉÉ
TOP VIEW
0.10 C
0.08 C
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.20 MM FROM TERMINAL TIP.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
L
PACKAGE
OUTLINE
0.73
L
L2
2.10
8
5
BOTTOM VIEW
8X
0.83
b
0.10
M
C A
0.05
M
C
1
B
8X
0.32
NOTE 3
0.50
PITCH
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
13
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCT203/D