CAV93C56 D

CAV93C56
2 Kb Microwire Serial CMOS
EEPROM
Description
The CAV93C56 is a 2 Kb CMOS Serial EEPROM device which is
organized as either 128 registers of 16 bits (ORG pin at VCC) or 256
registers of 8 bits (ORG pin at GND). Each register can be written (or
read) serially by using the DI (or DO) pin. The CAV93C56 features
sequential read and self−timed internal write with auto−clear. On−chip
Power−On Reset circuitry protects the internal logic against powering
up in the wrong state.
Features
•
•
•
•
•
•
•
•
•
•
•
•
Automotive Temperature Grade 1 (−40°C to +125°C)
High Speed Operation: 2 MHz
2.5 V to 5.5 V Supply Voltage Range
Selectable x8 or x16 Memory Organization
Sequential Read
Software Write Protection
Power−up Inadvertant Write Protection
Low Power CMOS Technology
1,000,000 Program/Erase Cycles
100 Year Data Retention
8−pin SOIC and TSSOP Packages
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
VCC
ORG
CS
SK
CAV93C56
DO
DI
http://onsemi.com
TSSOP−8
Y SUFFIX
CASE 948AL
SOIC−8
V SUFFIX
CASE 751BD
PIN CONFIGURATIONS
CS
SK
DI
DO
1
VCC
NC
ORG
GND
SOIC (V), TSSOP (Y)
(Top View)
PIN FUNCTION
Pin Name
Function
CS
Chip Select
SK
Clock Input
DI
Serial Data Input
DO
Serial Data Output
VCC
Power Supply
GND
Ground
ORG
Memory Organization
NC
No Connection
GND
Figure 1. Functional Symbol
ORDERING INFORMATION
NOTE: When the ORG pin is connected to VCC, the x16 organization is selected.
When it is connected to ground, the x8 pin is selected. If the ORG pin is left
unconnected, then an internal pullup device will select the x16 organization.
© Semiconductor Components Industries, LLC, 2013
December, 2013 − Rev. 0
1
See detailed ordering and shipping information in the package
dimensions section on page 10 of this data sheet.
Publication Order Number:
CAV93C56/D
CAV93C56
Table 1. ABSOLUTE MAXIMUM RATINGS
Parameters
Ratings
Units
Storage Temperature
−65 to +150
°C
Voltage on Any Pin with Respect to Ground (Note 1)
−0.5 to +6.5
V
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. The DC input voltage on any pin should not be lower than −0.5 V or higher than VCC + 0.5 V. During transitions, the voltage on any pin may
undershoot to no less than −1.5 V or overshoot to no more than VCC + 1.5 V, for periods of less than 20 ns.
Table 2. RELIABILITY CHARACTERISTICS (Note 2)
Parameter
Symbol
NEND (Note 3)
TDR
Endurance
Min
Units
1,000,000
Program / Erase Cycles
100
Years
Data Retention
2. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC−Q100
and JEDEC test methods.
3. Block Mode, VCC = 5 V, 25°C
Table 3. D.C. OPERATING CHARACTERISTICS
(VCC = +2.5 V to +5.5 V, TA=−40°C to +125°C unless otherwise specified.)
Parameter
Symbol
Test Conditions
Min
Max
Units
ICC1
Power Supply Current (Write)
VCC = 5.0 V
2
mA
ICC2
Power Supply Current (Read)
fSK = 2 MHz, VCC = 5.0 V, DO open
500
mA
ISB1
Power Supply Current (Standby)
(x8 Mode)
VIN = GND or VCC,
CS = GND ORG = GND
5
mA
ISB2
Power Supply Current (Standby)
(x16 Mode)
VIN = GND or VCC,
CS = GND ORG = Float or VCC
3
mA
VIN = GND to VCC
2
mA
VOUT = GND to VCC, CS = GND
2
mA
0.8
V
ILI
Input Leakage Current
ILO
Output Leakage Current
VIL1
Input Low Voltage
4.5 V v VCC < 5.5 V
−0.1
VIH1
Input High Voltage
4.5 V v VCC < 5.5 V
2
VCC + 1
V
VIL2
Input Low Voltage
2.5 V v VCC < 4.5 V
0
VCC x 0.2
V
VIH2
Input High Voltage
2.5 V v VCC < 4.5 V
VCC x 0.7
VCC + 1
V
VOL1
Output Low Voltage
4.5 V v VCC < 5.5 V, IOL = 3 mA
0.4
V
VOH1
Output High Voltage
4.5 V v VCC < 5.5 V, IOH = −400 mA
VOL2
Output Low Voltage
2.5 V v VCC < 4.5 V, IOL = 1 mA
VOH2
Output High Voltage
2.5 V v VCC < 4.5 V, IOH = −100 mA
2.4
V
0.2
VCC − 0.2
V
V
Table 4. PIN CAPACITANCE (TA = 25°C, f = 1 MHz, VCC = 5 V)
Symbol
COUT (Note 4)
CIN (Note 4)
Test
Conditions
Output Capacitance (DO)
Input Capacitance (CS, SK, DI, ORG)
Min
Typ
Max
Units
VOUT = 0 V
5
pF
VIN = 0 V
5
pF
4. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC−Q100
and JEDEC test methods.
http://onsemi.com
2
CAV93C56
Table 5. A.C. CHARACTERISTICS (Note 5)
(VCC = +2.5V to +5.5V, TA = −40°C to +125°C, unless otherwise specified.)
Limits
Symbol
Min
Parameter
tCSS
CS Setup Time
tCSH
tDIS
Max
Units
50
ns
CS Hold Time
0
ns
DI Setup Time
100
ns
tDIH
DI Hold Time
100
ns
tPD1
Output Delay to 1
0.25
ms
tPD0
Output Delay to 0
0.25
ms
Output Delay to High−Z
100
ns
5
ms
tHZ (Note 6)
tEW
Program/Erase Pulse Width
tCSMIN
Minimum CS Low Time
0.25
ms
tSKHI
Minimum SK High Time
0.25
ms
tSKLOW
Minimum SK Low Time
0.25
ms
tSV
Output Delay to Status Valid
SKMAX
Maximum Clock Frequency
DC
0.25
ms
2000
kHz
Table 6. A.C. TEST CONDITIONS
Input Rise and Fall Times
≤ 50 ns
Input Pulse Voltages
0.4 V to 2.4 V
4.5 V v VCC v 5.5 V
Timing Reference Voltages
0.8 V, 2.0 V
4.5 V v VCC v 5.5 V
Input Pulse Voltages
0.2 VCC to 0.7 VCC
2.5 V v VCC v 4.5 V
Timing Reference Voltages
0.5 VCC
2.5 V v VCC v 4.5 V
Output Load
Current Source IOLmax/IOHmax; CL=100 pF
Table 7. POWER−UP TIMING (Notes 6 and 7)
Parameter
Symbol
Max
Units
tPUR
Power−up to Read Operation
1
ms
tPUW
Power−up to Write Operation
1
ms
5. Test conditions according to “A.C. Test Conditions” table.
6. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate
AEC−Q100 and JEDEC test methods.
7. tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated.
http://onsemi.com
3
CAV93C56
Device Operation
The CAV93C56 is a 2048−bit nonvolatile memory
intended for use with industry standard microprocessors.
The CAV93C56 can be organized as either registers of 16
bits or 8 bits. When organized as X16, seven 11−bit
instructions control the reading, writing and erase
operations of the device. When organized as X8, seven
12−bit instructions control the reading, writing and erase
operations of the device. The CAV93C56 operates on a
single power supply and will generate on chip, the high
voltage required during any write operation.
Instructions, addresses, and write data are clocked into the
DI pin on the rising edge of the clock (SK). The DO pin is
normally in a high impedance state except when reading data
from the device, or when checking the ready/busy status
after a write operation. The serial communication protocol
follows the timing shown in Figure 2.
The ready/busy status can be determined after the start of
internal write cycle by selecting the device (CS high) and
polling the DO pin; DO low indicates that the write
operation is not completed, while DO high indicates that the
device is ready for the next instruction. If necessary, the DO
pin may be placed back into a high impedance state during
chip select by shifting a dummy “1” into the DI pin. The DO
pin will enter the high impedance state on the rising edge of
the clock (SK). Placing the DO pin into the high impedance
state is recommended in applications where the DI pin and
the DO pin are to be tied together to form a common
DI/O pin.
The format for all instructions sent to the device is a
logical “1” start bit, a 2−bit (or 4−bit) opcode, 8−bit address
(an additional bit when organized X8) and for write
operations a 16−bit data field (8−bit for X8 organizations).
The instruction format is shown in Instruction Set table.
Table 8. INSTRUCTION SET (Note 8)
Address
Data
Instruction
Start
Bit
Opcode
x8
x16
READ
1
10
A8−A0
A7−A0
ERASE
1
11
A8−A0
A7−A0
WRITE
1
01
A8−A0
A7−A0
EWEN
1
00
11XXXXXXX
11XXXXXX
Write Enable
EWDS
1
00
00XXXXXXX
00XXXXXX
Write Disable
ERAL
1
00
10XXXXXXX
10XXXXXX
Clear All Addresses
WRAL
1
00
01XXXXXXX
01XXXXXX
x8
x16
Comments
Read Address AN–A0
Clear Address AN–A0
D7−D0
D7−D0
D15−D0
D15−D0
Write Address AN–A0
Write All Addresses
8. Address bit A8 for 256x8 organization and A7 for 128x16 organization are “Don’t Care” bits, but must be kept at either a “1” or “0” for READ,
WRITE and ERASE commands.
tSKHI
tSKLOW
tCSH
SK
tDIH
tDIS
VALID
VALID
DI
tCSS
CS
tDIS
tPD0, tPD1
DO
DATA VALID
Figure 2. Synchronous Data Timing
http://onsemi.com
4
tCSMN
CAV93C56
Read
data word is preceeded by a dummy zero bit. All subsequent
data words will follow without a dummy zero bit. The
READ instruction timing is illustrated in Figure 3.
Upon receiving a READ command and an address
(clocked into the DI pin), the DO pin of the CAV93C56 will
come out of the high impedance state and, after sending an
initial dummy zero bit, will begin shifting out the data
addressed (MSB first). The output data bits will toggle on
the rising edge of the SK clock and are stable after the
specified time delay (tPD0 or tPD1).
For the CAV93C56, after the initial data word has been
shifted out and CS remains asserted with the SK clock
continuing to toggle, the device will automatically
increment to the next address and shift out the next data word
in a sequential READ mode. As long as CS is continuously
asserted and SK continues to toggle, the device will keep
incrementing to the next address automatically until it
reaches to the end of the address space, then loops back to
address 0. In the sequential READ mode, only the initial
Erase/Write Enable and Disable
The CAV93C56 powers up in the write disable state. Any
writing after power−up or after an EWDS (erase/write
disable) instruction must first be preceded by the EWEN
(erase/write enable) instruction. Once the write instruction
is enabled, it will remain enabled until power to the device
is removed, or the EWDS instruction is sent. The EWDS
instruction can be used to disable all CAV93C56 write and
erase instructions, and will prevent any accidental writing or
clearing of the device. Data can be read normally from the
device regardless of the write enable/disable status. The
EWEN and EWDS instructions timing is shown in Figure 4.
SK
CS
AN
DI
1
1
AN−1
Don’t Care
A0
0
tPD0
HIGH−Z
DO
Dummy 0
D15 . . . D0
or
D7 . . . D0
Address + 1
D15 . . . D0
or
D7 . . . D0
Address + 2
D15 . . . D0
or
D7 . . . D0
Figure 3. READ Instruction Timing
SK
STANDBY
CS
DI
1
0
0
*
* ENABLE = 11
DISABLE = 00
Figure 4. EWEN/EWDS Instruction Timing
http://onsemi.com
5
Address + n
D15 . . .
or
D7 . . .
CAV93C56
Write
Erase
After receiving a WRITE command (Figure 5), address
and the data, the CS (Chip Select) pin must be deselected for
a minimum of tCSMIN. The falling edge of CS will start the
self clocking clear and data store cycle of the memory
location specified in the instruction. The clocking of the SK
pin is not necessary after the device has entered the self
clocking mode. The ready/busy status of the CAV93C56 can
be determined by selecting the device and polling the DO
pin. Since this device features Auto−Clear before write, it is
NOT necessary to erase a memory location before it is
written into.
Upon receiving an ERASE command and address, the CS
(Chip Select) pin must be deasserted for a minimum of
tCSMIN (Figure 6). The falling edge of CS will start the self
clocking clear cycle of the selected memory location. The
clocking of the SaK pin is not necessary after the device has
entered the self clocking mode. The ready/busy status of the
CAV93C56 can be determined by selecting the device and
polling the DO pin. Once cleared, the content of a cleared
location returns to a logical “1” state.
SK
tCSMIN
CS
STATUS
VERIFY
AN
DI
1
0
AN−1
A0
DN
STANDBY
D0
1
tSV
BUSY
HIGH−Z
DO
READY
tHZ
HIGH−Z
tEW
Figure 5. Write Instruction Timing
SK
CS
STATUS VERIFY
AN
DI
1
1
AN−1
tCS
A0
1
tSV
DO
STANDBY
HIGH−Z
tHZ
BUSY
tEW
Figure 6. Erase Instruction Timing
http://onsemi.com
6
READY
HIGH−Z
CAV93C56
Erase All
Write All
Upon receiving an ERAL command (Figure 7), the CS
(Chip Select) pin must be deselected for a minimum of
tCSMIN. The falling edge of CS will start the self clocking
clear cycle of all memory locations in the device. The
clocking of the SK pin is not necessary after the device has
entered the self clocking mode. The ready/busy status of the
CAV93C56 can be determined by selecting the device and
polling the DO pin. Once cleared, the contents of all memory
bits return to a logical “1” state.
Upon receiving a WRAL command and data, the CS
(Chip Select) pin must be deselected for a minimum of
tCSMIN (Figure 8). The falling edge of CS will start the self
clocking data write to all memory locations in the device.
The clocking of the SK pin is not necessary after the device
has entered the self clocking mode. The ready/busy status of
the CAV93C56 can be determined by selecting the device
and polling the DO pin. It is not necessary for all memory
locations to be cleared before the WRAL command is
executed.
SK
CS
STATUS VERIFY
STANDBY
tCS
DI
1
0
1
0
0
tSV
tHZ
HIGH−Z
DO
BUSY
READY
HIGH−Z
tEW
Figure 7. ERAL Instruction Timing
SK
CS
STATUS VERIFY
STANDBY
tCSMIN
DI
1
0
0
0
1
DN
D0
tSV
tHZ
BUSY
DO
tEW
Figure 8. WRAL Instruction Timing
http://onsemi.com
7
READY
HIGH−Z
CAV93C56
PACKAGE DIMENSIONS
SOIC 8, 150 mils
CASE 751BD−01
ISSUE O
E1
E
SYMBOL
MIN
A
1.35
1.75
A1
0.10
0.25
b
0.33
0.51
c
0.19
0.25
D
4.80
5.00
E
5.80
6.20
E1
3.80
MAX
4.00
1.27 BSC
e
PIN # 1
IDENTIFICATION
NOM
h
0.25
0.50
L
0.40
1.27
θ
0º
8º
TOP VIEW
D
h
A1
θ
A
c
e
b
L
SIDE VIEW
END VIEW
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MS-012.
http://onsemi.com
8
CAV93C56
PACKAGE DIMENSIONS
TSSOP8, 4.4x3
CASE 948AL−01
ISSUE O
b
SYMBOL
MIN
NOM
1.20
A
E1
E
MAX
A1
0.05
A2
0.80
b
0.19
0.15
0.90
1.05
0.30
c
0.09
D
2.90
3.00
3.10
E
6.30
6.40
6.50
E1
4.30
4.40
4.50
0.20
0.65 BSC
e
L
1.00 REF
L1
0.50
θ
0º
0.60
0.75
8º
e
TOP VIEW
D
A2
c
q1
A
A1
L1
SIDE VIEW
L
END VIEW
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MO-153.
http://onsemi.com
9
CAV93C56
Example of Ordering Information
Device Order
Number
CAV93C56VE−GT3
CAV93C56YE−GT3
Specific
Device
Marking
Package Type
Temperature Range
Lead
Finish
93C56D
SOIC−8
−40°C to +125°C
NiPdAu
Tape & Reel,
3,000 Units / Reel
M56D
TSSOP−8
−40°C to +125°C
NiPdAu
Tape & Reel,
3,000 Units / Reel
Shipping
9. All packages are RoHS−compliant (Lead−free, Halogen−free).
10. The standard lead finish is NiPdAu.
11. For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
12. For detailed information and a breakdown of device nomenclature and numbering systems, please see the ON Semiconductor Device
Nomenclature document, TND310/D, available at www.onsemi.com
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
10
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
CAV93C56/D