MC100LVEL51 D

MC100LVEL51
3.3V ECL Differential Clock
D Flip‐Flop
Description
The MC100LVEL51 is a differential clock D flip-flop with reset. The
device is functionally equivalent to the EL51 device, but operates from a
3.3 V supply. With propagation delays and output transition times
essentially equal to the EL51, the LVEL51 is ideally suited for those
applications which require the ultimate in AC performance at 3.3 V VCC.
The reset input is an asynchronous, level triggered signal. Data enters
the master portion of the flip-flop when the clock is LOW and is
transferred to the slave, and thus the outputs, upon a positive transition of
the clock. The differential clock inputs of the LVEL51 allow the device to
be used as a negative edge triggered flip-flop.
The differential input employs clamp circuitry to maintain stability
under open input conditions. When left open, the CLK input will be
pulled down to VEE and the CLK input will be biased at VCC/2.
http://onsemi.com
MARKING
DIAGRAMS*
8
8
1
KVL51
ALYW
G
SOIC−8
D SUFFIX
CASE 751
1
8
8
1
Features
• 475 ps Propagation Delay
• 2.8 GHz Toggle Frequency
• ESD Protection: >4 kV Human Body Model,
TSSOP−8
DT SUFFIX
CASE 948R
1
KV51
ALYWG
G
>200 V Machine Model
4G M G
G
• The 100 Series Contains Temperature Compensation
• PECL Mode Operating Range: VCC = 3.0 V to 3.8 V
with VEE = 0 V
1
• NECL Mode Operating Range: VCC = 0 V
•
•
•
•
•
•
with VEE = −3.0 V to −3.8 V
Internal Input Pulldown Resistors
Meets or Exceeds JEDEC Spec EIA/JESD78 IC Latchup Test
Moisture Sensitivity Level 1
For Additional Information, see Application Note AND8003/D
Flammability Rating: UL 94 V−0 @ 0.125 in,
Oxygen Index: 28 to 34
Transistor Count = 114 devices
Pb−Free Packages are Available
4
DFN8
MN SUFFIX
CASE 506AA
A
L
Y
W
M
G
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Date Code
= Pb−Free Package
(Note: Microdot may be in either location)
*For additional marking information, refer to
Application Note AND8002/D.
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 6 of this data sheet.
© Semiconductor Components Industries, LLC, 2008
August, 2008 − Rev. 6
1
Publication Order Number:
MC100LVEL51/D
MC100LVEL51
R
1
D
2
8
VCC
7
Q
R
D
Flip-Flop
CLK
3
6
Q
CLK
4
5
VEE
Figure 1. Logic Diagram and Pinout Assignment
Table 1. PIN DESCRIPTION
Table 2. TRUTH TABLE
PIN
FUNCTION
D
R
CLK
Q
CLK, CLK
ECL Differential Clock Input
ECL Differential Output
ECL D Input
ECL Reset Input
Positive Supp;y
Negative Supply
L
H
X
L
L
H
Z
Z
X
L
H
L
Q, Q
D
R
VCC
VEE
EP
Z = LOW to HIGH Transition
X = Don’t Care
(DFN8 only) Thermal exposed pad must be
connected to a sufficient thermal conduit. Electrically connect to the most negative supply
(GND) or leave unconnected, floating open.
http://onsemi.com
2
MC100LVEL51
Table 3. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Rating
Unit
8 to 0
V
−8 to 0
V
6 to 0
−6 to 0
V
V
50
100
mA
mA
Operating Temperature Range
−40 to +85
°C
Storage Temperature Range
−65 to +150
°C
8 SOIC
8 SOIC
190
130
°C/W
°C/W
Standard Board
8 SOIC
41 to 44 ± 5%
°C/W
Thermal Resistance (Junction−to−Ambient)
0 lfpm
500 lfpm
8 TSSOP
8 TSSOP
185
140
°C/W
°C/W
qJC
Thermal Resistance (Junction−to−Case)
Standard Board
8 TSSOP
41 to 44 ± 5%
°C/W
qJA
Thermal Resistance (Junction−to−Ambient)
0 lfpm
500 lfpm
DFN8
DFN8
129
84
°C/W
°C/W
Tsol
Wave Solder
<2 to 3 sec @ 248°C
<2 to 3 sec @ 260°C
265
265
°C
qJC
Thermal Resistance (Junction−to−Case)
35 to 40
°C/W
VCC
PECL Mode Power Supply
VEE = 0 V
VEE
NECL Mode Power Supply
VCC = 0 V
VI
PECL Mode Input Voltage
NECL Mode Input Voltage
VEE = 0 V
VCC = 0 V
Iout
Output Current
Continuous
Surge
TA
Tstg
qJA
Thermal Resistance (Junction−to−Ambient)
0 lfpm
500 lfpm
qJC
Thermal Resistance (Junction−to−Case)
qJA
Pb
Pb−Free
(Note 1)
Condition 2
VI VCC
VI VEE
DFN8
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. JEDEC standard multilayer board − 2S2P (2 signal, 2 power)
http://onsemi.com
3
MC100LVEL51
Table 4. LVPECL DC CHARACTERISTICS VCC = 3.3 V; VEE = 0.0 V (Note 1)
−40°C
Symbol
Characteristic
Min
25°C
Typ
Max
30
35
Min
85°C
Typ
Max
30
35
Min
Typ
Max
Unit
32
37
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 3)
2215
2295
2420
2275
2345
2420
2275
2345
2420
mV
VOL
Output LOW Voltage (Note 3)
1470
1605
1745
1490
1595
1680
1490
1595
1680
mV
VIH
Input HIGH Voltage (Single−Ended)
2135
2420
2135
2420
2135
2420
mV
VIL
Input LOW Voltage (Single−Ended)
1490
1825
1490
1825
1490
1825
mV
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential) (Note 7)
VPP < 500 mV
VPP y 500 mV
1.2
1.4
3.0
3.0
1.1
1.3
3.0
3.0
1.1
1.3
3.0
3.0
V
V
150
mA
IIH
Input HIGH Current
IIL
Input LOW Current
150
Others
CLK
0.5
−600
150
0.5
−600
0.5
−600
mA
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
2. Input and output parameters vary 1:1 with VCC. VEE can vary ±0.3 V.
3. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
4. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal.
Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V.
Table 5. LVNECL DC CHARACTERISTICS VCC = 0.0 V; VEE = −3.3 V (Note 5)
−40°C
Symbol
Characteristic
Min
25°C
Typ
Max
30
35
Min
85°C
Typ
Max
30
35
Min
Typ
Max
Unit
32
37
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 6)
−1085
−1005
−880
−1025
−955
−880
−1025
−955
−880
mV
VOL
Output LOW Voltage (Note 6)
−1830
−1695
−1555
−1810
−1705
−1620
−1810
−1705
−1620
mV
VIH
Input HIGH Voltage (Single−Ended)
−1165
−880
−1165
−880
−1165
−880
mV
VIL
Input LOW Voltage (Single−Ended)
−1810
−1475
−1810
−1475
−1810
−1475
mV
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential) (Note 7)
VPP < 500 mV
VPP y 500 mV
−2.1
−1.9
−0.3
−0.3
−2.2
−2.0
−0.3
−0.3
−2.2
−2.0
−0.3
−0.3
V
V
150
mA
IIH
Input HIGH Current
IIL
Input LOW Current
150
Others
CLK
0.5
−600
150
0.5
−600
0.5
−600
mA
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
5. Input and output parameters vary 1:1 with VCC. VEE can vary ±0.3 V.
6. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
7. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal.
Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V.
http://onsemi.com
4
MC100LVEL51
Table 6. AC CHARACTERISTICS VCC = 3.3 V; VEE = 0.0 V or VCC = 0.0 V; VEE = −3.3 V (Note 8)
−40°C
Symbol
Characteristic
Min
Typ
25°C
Max
2.7
Min
85°C
Typ
Max
Min
Max
Maximum Toggle Frequency
tPLH
tPHL
Propagation Delay
to Output
tS
Setup Time
150
0
150
0
150
0
ps
tH
Hold Time
200
100
200
100
200
100
ps
tRR
Reset Recovery
350
200
350
200
350
200
ps
tPW
Minimum Pulse
Width
tJITTER
Cycle−to−Cycle Jitter
VPP
Input Swing (Note 9)
150
1000
150
1000
150
1000
mV
tr
tf
Output Rise/Fall Times Q
(20% − 80%)
120
320
120
320
120
320
ps
CLK
Reset
330
340
465
455
510
540
400
500
340
350
2.9
Unit
fmax
CLK
R
2.8
Typ
475
465
520
550
370
390
400
500
TBD
GHz
530
510
550
590
400
500
TBD
ps
ps
TBD
ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
8. VEE can vary ±0.3 V.
9. VPP(min) is minimum input swing for which AC parameters are guaranteed.
Q
Zo = 50 W
D
Receiver
Device
Driver
Device
Q
D
Zo = 50 W
50 W
50 W
VTT
VTT = VCC − 3.0 V
Figure 2. Typical Termination for Output Driver and Device Evaluation
(See Application Note AND8020/D − Termination of ECL Logic Devices.)
http://onsemi.com
5
MC100LVEL51
ORDERING INFORMATION
Package
Shipping†
SOIC−8
98 Units / Rail
MC100LVEL51DG
SOIC−8
(Pb−Free)
98 Units / Rail
MC100LVEL51DR2
SOIC−8
2500 / Tape & Reel
MC100LVEL51DR2G
SOIC−8
(Pb−Free)
2500 / Tape & Reel
MC100LVEL51DT
TSSOP−8
100 Units / Rail
MC100LVEL51DTG
TSSOP−8
(Pb−Free)
100 Units / Rail
MC100LVEL51DTR2
TSSOP−8
2500 / Tape & Reel
MC100LVEL51DTR2G
TSSOP−8
(Pb−Free)
2500 / Tape & Reel
MC100LVEL51MNR4
DFN8
1000 / Tape & Reel
DFN8
(Pb−Free)
1000 / Tape & Reel
Device
MC100LVEL51D
MC100LVEL51MNR4G
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
Resource Reference of Application Notes
AN1405/D
− ECL Clock Distribution Techniques
AN1406/D
− Designing with PECL (ECL at +5.0 V)
AN1503/D
− ECLinPSt I/O SPiCE Modeling Kit
AN1504/D
− Metastability and the ECLinPS Family
AN1568/D
− Interfacing Between LVDS and ECL
AN1672/D
− The ECL Translator Guide
AND8001/D
− Odd Number Counters Design
AND8002/D
− Marking and Date Codes
AND8020/D
− Termination of ECL Logic Devices
AND8066/D
− Interfacing with ECLinPS
AND8090/D
− AC Characteristics of ECL Devices
http://onsemi.com
6
MC100LVEL51
PACKAGE DIMENSIONS
SOIC−8 NB
CASE 751−07
ISSUE AJ
−X−
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
A
8
5
S
B
0.25 (0.010)
M
Y
M
1
4
−Y−
K
G
C
N
DIM
A
B
C
D
G
H
J
K
M
N
S
X 45 _
SEATING
PLANE
−Z−
0.10 (0.004)
H
D
0.25 (0.010)
M
Z Y
S
X
M
J
S
SOLDERING FOOTPRINT*
1.52
0.060
7.0
0.275
4.0
0.155
0.6
0.024
1.270
0.050
SCALE 6:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
7
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0_
8_
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0 _
8 _
0.010
0.020
0.228
0.244
MC100LVEL51
PACKAGE DIMENSIONS
TSSOP−8
DT SUFFIX
PLASTIC TSSOP PACKAGE
CASE 948R−02
ISSUE A
8x
0.15 (0.006) T U
0.10 (0.004)
S
2X
L/2
L
8
5
1
PIN 1
IDENT
0.15 (0.006) T U
K REF
M
T U
V
S
0.25 (0.010)
B
−U−
4
M
A
−V−
S
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH.
PROTRUSIONS OR GATE BURRS. MOLD FLASH
OR GATE BURRS SHALL NOT EXCEED 0.15
(0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED 0.25 (0.010)
PER SIDE.
5. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
6. DIMENSION A AND B ARE TO BE DETERMINED
AT DATUM PLANE -W-.
S
F
DETAIL E
C
0.10 (0.004)
−T− SEATING
PLANE
D
−W−
G
DETAIL E
http://onsemi.com
8
DIM
A
B
C
D
F
G
K
L
M
MILLIMETERS
MIN
MAX
2.90
3.10
2.90
3.10
0.80
1.10
0.05
0.15
0.40
0.70
0.65 BSC
0.25
0.40
4.90 BSC
0_
6_
INCHES
MIN
MAX
0.114
0.122
0.114
0.122
0.031
0.043
0.002
0.006
0.016
0.028
0.026 BSC
0.010
0.016
0.193 BSC
0_
6_
MC100LVEL51
PACKAGE DIMENSIONS
DFN8
CASE 506AA−01
ISSUE D
D
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994 .
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.25 AND 0.30 MM FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
A
B
PIN ONE
REFERENCE
2X
0.10 C
2X
ÇÇÇÇ
ÇÇÇÇ
ÇÇÇÇ
ÇÇÇÇ
TOP VIEW
0.10 C
0.08 C
SEATING
PLANE
MILLIMETERS
MIN
MAX
0.80
1.00
0.00
0.05
0.20 REF
0.20
0.30
2.00 BSC
1.10
1.30
2.00 BSC
0.70
0.90
0.50 BSC
0.20
−−−
0.25
0.35
A
0.10 C
8X
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
E
(A3)
SIDE VIEW
A1
C
D2
e
e/2
4
1
8X
L
E2
K
8
5
8X
b
0.10 C A B
0.05 C
NOTE 3
BOTTOM VIEW
ECLinPS is a trademark of Semiconductor Components Industries, LLC (SCILLC).
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
9
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC100LVEL51/D