NLAS3158 D

NLAS3158
Low Voltage Dual SPDT
Analog Switch Dual 2:1
Multiplexer
The NLAS3158 is an advanced CMOS analog switch fabricated
with silicon gate CMOS technology. It achieves very low
propagation delay and RDSON resistances while maintaining CMOS
low power dissipation. Analog and digital voltages that may vary
across the full power−supply range (from VCC to GND). This device
is a drop in replacement for the PI5A3158.
The select pin has overvoltage protection that allows voltages
above VCC, up to 7.0 V to be present on the pin without damage or
di srupt i on of ope ra t i on of the pa rt , re ga rdl e ss of the
operating voltage.
www.onsemi.com
12
1
MARKING DIAGRAM
ASMG
G
Features
•
•
•
•
•
•
•
WDFN12
MN SUFFIX
CASE 485AG
1
High Speed: tPD = 1.0 ns (Typ) at VCC = 5.0 V
Low Power Dissipation: ICC = 1.0 mA (Max) at TA = 25°C
Standard CMOS Logic Levels
High Bandwidth, Improved Linearity
Low RDSON: 8 W Max at 3 V
Break Before Make Circuitry, Prevents Inadvertent Shorts
This is a Pb−Free Device
AS = Specific Device Code
M = Date Code
G
= Pb−Free Package
(Note: Microdot may be in either location)
FUNCTION TABLE
Select Input
L
H
Typical Applications
• Switches Standard NTSC/PAL Video, Audio, SPDIF and HDTV
• May be used for Clock Switching, Data MUX’ing, etc.
• Can Switch Balanced Signal Pairs, e.g. LVDS u 200 Mb/s
Function
B0 Connected to A
B1 Connected to A
A0
1
12
VCC
0B0
2
11
0B1
GND
3
10
S0
A1
4
9
VCC
1B0
5
8
1B1
GND
6
7
S1
Important Information
•
•
•
•
•
Latchup Performance Exceeds 300 mA
Pin for Pin Drop in for PI5A3158
WDFN Package, 3x1 mm
ESD Performance: Human Body Model; u 2000 V;
Machine Model; u 200 V
Extended Automotive Temperature Range −55°C to +125°C
(See Appendix A)
Figure 1. Pinout (Top View)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 11 of this data sheet.
© Semiconductor Components Industries, LLC, 2015
November, 2015 − Rev. 2
1
Publication Order Number:
NLAS3158/D
NLAS3158
MAXIMUM RATINGS
Symbol
Value
Unit
Supply Voltage
Rating
VCC
−0.5 to +7.0
V
DC Switch Input Voltage (Note 1)
VIS
−0.5 to VCC + 0.5
V
DC Input Voltage (Note 1)
VIN
−0.5 to + 7.0
V
DC Input Diode Current @ VIN t 0 V
IIK
−50
mA
IOUT
128
mA
DC VCC or Ground Current
ICC/IGND
+100
mA
Storage Temperature Range
Tstg
−65 to +150
°C
Junction Temperature Under Bias
TJ
150
°C
Junction Lead Temperature (Soldering, 10 Seconds)
TL
260
°C
Power Dissipation @ +85°C
PD
180
mW
DC Output Current
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed.
RECOMMENDED OPERATING CONDITIONS (Note 2)
Characteristic
Symbol
Min
Max
Unit
Supply Voltage Operating
VCC
1.65
5.5
V
Select Input Voltage
VIN
0
VCC
V
Switch Input Voltage
VIS
0
VCC
V
VOUT
0
VCC
V
Operating Temperature
TA
−55
+125
°C
Input Rise and Fall Time
Control Input VCC = 2.3 V−3.6 V
Control Input VCC = 4.5 V−5.5 V
tr, tf
0
0
10
5.0
Thermal Resistance
qJA
−
350
Output Voltage
ns/V
°C/W
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the
Recommended Operating Ranges limits may affect device reliability.
2. Select input must be held HIGH or LOW, it must not float.
www.onsemi.com
2
NLAS3158
DC ELECTRICAL CHARACTERISTICS (TA = −40°C to +85°C)
Symbol
Parameter
VCC
(V)
Test Conditions
TA = +255C
Min
Typ
VIH
HIGH Level
Input Voltage
1.65−1.95
2.3−5.5
VIL
LOW Level
Input Voltage
1.65−1.95
2.3−5.5
IIN
Input Leakage Current
0 v VIN v 5.5 V
0−5.5
"0.0
5
IOFF
OFF State Leakage
Current
0 v A, B v VCC
1.65−5.5
RON
Switch On Resistance
(Note 3)
VIN = 0 V, IO = 30 mA
VIN = 2.4 V, IO = −30 mA
VIN = 4.5 V, IO = −30 mA
ICC
Quiescent Supply
Current
All Channels ON or
OFF
TA = −405C to +855C
Max
Min
Max
0.75 VCC
0.7 VCC
Unit
V
0.25 VCC
0.3 VCC
V
"0.1
"1
mA
"0.0
5
"0.1
"1
mA
4.5
3.0
5.0
7.0
6.0
8.0
13
6.0
8.0
13
W
VIN = 0 V, IO = 24 mA
VIN = 3 V, IO = −24 mA
3.0
4.0
10
8.0
19
8.0
19
W
VIN = 0 V, IO = 8 mA
VIN = 2.3 V, IO = −8 mA
2.3
5.0
13
9.0
24
9.0
24
W
VIN = 0 V, IO = 4 mA
VIN = 1.65 V, IO = −4 mA
1.65
6.5
17
12
39
12
39
W
VIN = VCC or GND
5.5
1.0
10
mA
VCC
V
25
50
100
300
W
IOUT = 0
Analog Signal Range
VCC
0
VCC
0
RRANGE
On Resistance
Over Signal Range
(Note 3) (Note 7)
IA = −30 mA, 0 v VBn v VCC
IA = −24 mA, 0 v VBn v VCC
IA = −8 mA, 0 v VBn v VCC
IA = −4 mA, 0 v VBn v VCC
4.5
3.0
2.3
1.65
DRON
On Resistance Match
Between Channels
(Note 3) (Note 4)
(Note 5)
IA = −30 mA, VBn = 3.15
IA = −24 mA, VBn = 2.1
IA = −8 mA, VBn = 1.6
IA = −4 mA, VBn = 1.15
4.5
3.0
2.3
1.65
0.15
0.2
0.5
0.5
W
Rflat
On Resistance
Flatness (Note 3)
(Note 4) (Note 6)
IA = −30 mA, 0 v VBn v VCC
IA = −24 mA, 0 v VBn v VCC
IA = −8 mA, 0 v VBn v VCC
IA = −4 mA, 0 v VBn v VCC
5.0
3.3
2.5
1.8
5.0
10
24
110
W
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
3. Measured by the voltage drop between A and B pins at the indicated current through the switch. On Resistance is determined by the lower
of the voltages on the two (A or B Ports).
4. Parameter is characterized but not tested in production.
5. DRON = RON max − RON min measured at identical VCC, temperature and voltage levels.
6. Flatness is defined as the difference between the maximum and minimum value of On Resistance over the specified range of conditions.
7. Guaranteed by Design.
www.onsemi.com
3
NLAS3158
AC ELECTRICAL CHARACTERISTICS (TA = −40°C to +85°C)
Symbol
Parameter
Test Conditions
tPHL
tPLH
Propagation Delay
Bus to Bus (Note 9)
VI = OPEN
tPZL
tPZH
Output Enable Time
Turn On Time
(A to Bn)
tPLZ
tPHZ
TA = +255C
VCC
(V)
Min
Typ
TA = −405C to +855C
Max
Min
1.65−1.95
2.3−2.7
3.0−3.6
4.5−5.5
1.2
0.8
0.3
VI = 2
VCC for tPZL
VI = 0 V for tPZH
1.65−1.95
2.3−2.7
3.0−3.6
4.5−5.5
23
13
6.9
5.2
7.0
3.5
2.5
1.7
Output Disable Time
Turn Off Time
(A Port to B Port)
VI = 2
VCC for tPLZ
VI = 0 V for tPHZ
1.65−1.95
2.3−2.7
3.0−3.6
4.5−5.5
12.5
7.0
5.0
3.5
3.0
2.0
1.5
0.8
tBBM
Break Before Make
Time (Note 8)
RL = 50 W
CL = 35 pF
1.65−1.95
2.3−2.7
3.0−3.6
4.5−5.5
Q
Charge Injection
(Note 8)
CL = 0.1 nF, VGEN = 0 V
RGEN = 0 W
OIRR
Off Isolation (Note 10)
NO
OIRR
0.5
0.5
0.5
0.5
Max
Unit
Figure
Number
ns
Figures
2, 3
24
14
7.6
5.7
ns
Figures
2, 3
13
7.5
5.3
3.8
ns
Figures
2, 3
ns
Figure 4
0.5
0.5
0.5
0.5
5.0
3.3
7.0
3.0
pC
Figure 5
RL = 50 W
f = 10 MHz
1.65−5.5
−55
dB
Figures
6, 16
Off Isolation (Note 10)
NC
RL = 50 W
f = 10 MHz
1.65−5.5
−48
dB
Figures
6, 16
Xtalk
Crosstalk
RL = 50 W
f = 10 MHz
1.65−5.5
−54
dB
Figure 7
BW
−3 dB Bandwidth
RL = 50 W
2.5−5.5
250
MHz
Figures
10, 15
THD
Total Harmonic
Distortion (Note 8)
RL = 600 W
0.5 VP−P
f = 600 Hz to 20 kHz
2.5
5.0
0.014
0.004
%
Figure 11
CAPACITANCE (Note 11)
Symbol
Parameter
Test Conditions
Typ
Max
Unit
Figure
Number
CIN
Select Pin Input Capacitance
VCC = 0 V
2.3
pF
CIO−B
B Port Off Capacitance
VCC = 5.0 V
6.5
pF
Figure 8
CIOA−ON
A Port Capacitance when Switch is Enabled
VCC = 5.0 V
18.5
pF
Figure 9
8. Guaranteed by Design.
9. This parameter is guaranteed by design but not tested. The bus switch contributes no propagation delay other than the RC delay of the On
Resistance of the switch and the 35 pF load capacitance, when driven by an ideal voltage source (zero output impedance).
10. Off Isolation = 20 log10 [VA/VBn].
11. TA = +25°C, f = 1 MHz, Capacitance is characterized but not tested in production.
www.onsemi.com
4
NLAS3158
APPENDIX A
DC ELECTRICAL EXTENDED AUTOMOTIVE TEMPERATURE RANGE CHARACTERISTICS (Note 14)
Symbol
Parameter
VCC
(V)
Test Conditions
TA = +255C
Min
Typ
VIH
HIGH Level
Input Voltage
1.65−1.95
2.3−5.5
VIL
LOW Level
Input Voltage
1.65−1.95
2.3−5.5
IIN
Input Leakage Current
0 v VIN v 5.5 V
0−5.5
"0.05
IOFF
OFF State Leakage
Current
0 v A, B v VCC
1.65−5.5
"0.05
RON
Switch On Resistance
(Note 12)
VIN = 0 V, IO = 30 mA
VIN = 2.4 V, IO = −30 mA
VIN = 4.5 V, IO = −30 mA
4.5
VIN = 0 V, IO = 24 mA
VIN = 3 V, IO = −24 mA
ICC
Quiescent Supply
Current
All Channels ON or
OFF
On Resistance
Over Signal Range
(Note 12) (Note 13)
Max
Min
Max
0.75 VCC
0.7 VCC
Unit
V
0.25 VCC
0.3 VCC
V
"0.1
"1
mA
"0.1
"1
mA
3.0
5.0
7.0
8.5
13.0
15.0
W
3.0
4.0
10
11
20
VIN = 0 V, IO = 8 mA
VIN = 2.3 V, IO = −8 mA
2.3
5.0
13
12
30
VIN = 0 V, IO = 4 mA
VIN = 1.65 V, IO = −4 mA
1.65
6.5
17
20
50
VIN = VCC or GND
5.5
10
mA
VCC
V
4.5
25
W
3.0
50
2.3
100
1.65
300
1.0
IOUT = 0
Analog Signal Range
RRANGE
TA = −555C to +1255C
VCC
IA = −30 mA, 0 v VBn v
VCC
IA = −24 mA, 0 v VBn v
VCC
IA = −8 mA, 0 v VBn
v VCC
IA = −4 mA, 0 v VBn
v VCC
0
VCC
0
12. Measured by the voltage drop between A and B pins at the indicated current through the switch. On Resistance is determined by the lower
of the voltages on the two (A or B Ports).
13. Guaranteed by Design.
14. For DRON, RFLAT see −40°C to +85°C section.
www.onsemi.com
5
NLAS3158
APPENDIX A
AC ELECTRICAL EXTENDED AUTOMOTIVE TEMPERATURE RANGE CHARACTERISTICS
Symbol
Parameter
Test Conditions
VCC
(V)
TA = +255C
Min
Typ
Max
TA = −555C to +1255C
Min
tPHL
tPLH
Propagation Delay
Bus to Bus (Note 16)
VI = OPEN
1.65−1.95
2.3−2.7
3.0−3.6
4.5−5.5
tPZL
tPZH
Output Enable Time
Turn On Time
(A to Bn)
VI = 2
VCC for tPZL
VI = 0 V for tPZH
1.65−1.95
2.3−2.7
3.0−3.6
4.5−5.5
23
13
6.9
5.2
7.0
3.5
2.5
1.7
tPLZ
tPHZ
Output Disable Time
Turn Off Time
(A Port to B Port)
VI = 2
VCC for tPLZ
VI = 0 V for tPHZ
1.65−1.95
2.3−2.7
3.0−3.6
4.5−5.5
12.5
7.0
5.0
3.5
3.0
2.0
1.5
0.8
tB−M
Break Before Make
Time (Note 15)
1.65−1.95
2.3−2.7
3.0−3.6
4.5−5.5
Max
Unit
ns
Figures
2, 3
24
14
9.0
7.0
ns
Figures
2, 3
13
7.5
6.5
5.0
ns
Figures
2, 3
ns
Figure 4
1.2
0.8
0.3
0.5
0.5
0.5
0.5
Figure
Number
15. Guaranteed by Design.
16. This parameter is guaranteed by design but not tested. The bus switch contributes no propagation delay other than the RC delay of the On
Resistance of the switch and the 50 pF load capacitance, when driven by an ideal voltage source (zero output impedance).
www.onsemi.com
6
NLAS3158
AC LOADING AND WAVEFORMS
VI
RU
FROM
OUTPUT
UNDER
TEST
NOTE: Input driven by 50 W source terminated in 50 W
NOTE: CL includes load and stray capacitance
NOTE: Input PRR = 1.0 MHz; tW = 500 ns
RD
CL
Figure 2. AC Test Circuit
tf = 2.5 ns
tr = 2.5 ns
SWITCH
INPUT
90%
tf = 2.5 ns
VCC
90%
50%
tPHL
50%
10%
OUTPUT
VOH
GND
tPLZ
VTRI
50%
tPZH
50%
VCC
50%
GND
tW
OUTPUT
50%
tPZL
10%
tPLH
90%
10%
50%
10%
tr = 2.5 ns
90%
SELECT
INPUT
VOL + 0.3 V
VOL
tPHZ
VOH
VOL
OUTPUT
VOH − 0.3 V
50%
VTRI
Figure 3. AC Waveforms
VIN
B0
B1
S
A
LOGIC
INPUT
VOUT
RL
CL
VOUT
LOGIC
INPUT
0.9 × VOUT
tD
Figure 4. Break Before Make Interval Timing
www.onsemi.com
7
NLAS3158
AC LOADING AND WAVEFORMS
RGEN
VGE
BN
A
LOGIC
INPUT
VOUT
S
RL
CL
1 MW
100 pF
OFF
ON
OFF
DVOUT
VOUT
Q = (DVOUT)(CL)
LOGIC
INPUT
Figure 5. Charge Injection Test
10 nF
10 nF
Signal
Generator
0 dBm
VCC
50 W
A
LOGIC INPUT
0 V or VIH
S
Analyzer
GND
50 W
Figure 6. Off Isolation
Figure 7. Crosstalk
10 nF
10 nF
Capacitance
Meter
VCC
A
Capacitance
Meter
f = 1 MHz
50 W
S
GND
50 W
A
B1
BN
Analyzer
VCC
B0
LOGIC INPUT
0 V or VCC
S
VCC
A
f = 1 MHz
S
BN
LOGIC INPUT
0 V or VCC
BN
GND
GND
Figure 8. Channel Off Capacitance
Figure 9. Channel On Capacitance
10 nF
Signal
Generator
0 dBm
VCC
A
BN
50 W
S
LOGIC INPUT
0 V or VCC
GND
Figure 10. Bandwidth
www.onsemi.com
8
NLAS3158
0.01
3.0 V
THD (%)
2.3 V
0.001
100
4.5 V
1000
10000
FREQUENCY (Hz)
Figure 11. Total Harmonic Distortion vs.
Frequency
www.onsemi.com
9
100000
NLAS3158
20
12
18
10
16
−40°C
8
12
RON (W)
RON (W)
14
10
−40°C
25°C
85°C
125°C
8
125°C
25°C
−55°C
4
−55°C
6
85°C
6
4
2
2
0
0.0
0.5
1.0
1.5
2.0
0
0.0
3.0
2.5
0.5
1.0
1.5
2.0
VIN (V)
2.5
3.0
3.5
4.0
4.5
VIN (V)
Figure 13. RON vs. VIN vs. Temperature
@ VCC = 4.5 V
Figure 12. RON vs. VIN vs. Temperature
@ VCC = 3.0 V
40
0
4.5 V
35
−2
2.3 V
−4
25
POUT (dB)
RON (W)
30
20
15
2.3 V
3.0 V
−6
−8
3.0 V
−10
10
−12
5
4.5 V
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
−14
0.01
5.0
0.1
VIN (V)
100
1000
Figure 15. Bandwidth vs. Frequency
0
35
2.3 V
−10
30
3.0 V
−20
25
20
−40
PHASE (deg)
−30
POUT (dB)
10
FREQUENCY (MHz)
Figure 14. On−Resistance vs. Input Voltage
4.5 V
−50
−60
−70
15
0
−5
−10
10
100
1000
3.0 V
5
−90
1.0
4.5 V
10
−80
−100
0.1
1.0
−15
0.01
2.3 V
0.1
1
10
100
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 16. Off−Isolation vs. Frequency
Figure 17. Phase Angle vs. Frequency
www.onsemi.com
10
1000
NLAS3158
DEVICE ORDERING INFORMATION
Device Order Number
NLAS3158MNR2G
Package Type
Tape & Reel Size†
WDFN12
(Pb−Free)
3000 Unit / Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
11
NLAS3158
PACKAGE DIMENSIONS
WDFN12 3.0x1.0, 0.5P
CASE 485AG
ISSUE A
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION b APPLIES TO TERMINAL AND
IS MEASURED BETWEEN 0.25 AND 0.30 MM
FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
A
B
D
PIN ONE
REFERENCE
E
2X
0.15 C
TOP VIEW
2X
DIM
A
A1
A3
b
D
E
e
L
0.15 C
(A3)
0.10 C
MILLIMETERS
MIN
MAX
0.70
0.80
0.00
0.05
0.20 REF
0.18
0.30
3.00 BSC
1.00 BSC
0.50 BSC
0.20
0.40
A
12 X
0.08 C
SEATING
PLANE
SIDE VIEW
A1
12 X L
1
e
10X
12
C
6
7
12 X b
0.10 C A B
BOTTOM VIEW
0.05 C
NOTE 3
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent− Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty,
representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product
or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in
SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must
be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products
are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or
for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products
for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against
all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended
or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action
Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
12
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NLAS3158/D