NLAS5123 D

NLAS5123
SPDT, 1 W RON Switch
The NLAS5123 is a low RON SPDT analog switch. This device is
designed for low operating voltage, high current switching of speaker
output for cell phone applications. It can switch a balanced stereo
output. The NLAS5123 can handle a balanced microphone/
speaker/ringtone generator in a monophone mode. The device
contains a break−before−make (BBM) feature.
http://onsemi.com
MARKING
DIAGRAMS
Features
• Single Supply Operation:
•
•
•
•
1.65 V to 5.5 V VCC
Function Directly from LiON Battery
RON Typical = 1.0 @ VCC = 4.5 V
Low Static Power
These are Pb−Free Devices
WDFN6
MN SUFFIX
CASE 506AS
WM
G
1
W = Specific Device Code
M = Date Code
G = Pb−Free Device
Typical Applications
• Cell Phone Speaker/Microphone Switching
• Ringtone−Chip/Amplifier Switching
• Stereo Balanced (Push−Pull) Switching
UDFN6
MU SUFFIX
CASE 517AA
1
XM
G
X = Specific Device Code
M = Date Code
G = Pb−Free Device
Important Information
• Continuous Current Rating Through each Switch ±300 mA
• 1.2 x 1.0 x 0.4P mm 6−Lead Thin DFN Package
PIN ASSIGNMENTS
NO
1
6
IN
GND
2
5
VCC
NC
3
4
COM
(Top View)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 8 of this data sheet.
© Semiconductor Components Industries, LLC, 2010
November, 2010 − Rev. 4
1
Publication Order Number:
NLAS5123/D
NLAS5123
COM
NC
NO
IN
Figure 1. Input Equivalent Circuit
PIN DESCRIPTION
Pin Name
TRUTH TABLE
Description
Control Input
Function
NC, NO, COM
Data Ports
L
NC Connected to COM
IN
Control Input
H
NO Connected to COM
H = HIGH Logic Level.
L = LOW Logic Level.
MAXIMUM RATINGS
Symbol
Rating
Value
Unit
−0.5 to +6.0
V
−0.5 to VCC +0.5
V
−0.5 to +6.0
V
Continuous DC Current from COM to NC/NO
±300
mA
Ianl−pk1
Peak Current from COM to NC/NO, 10 Duty Cycles (Note 1)
±500
mA
Iclmp
Continuous DC Current into COM/NC/NO with respect to VCC or GND
±100
mA
VCC
Positive DC Supply Voltage
VIS
Analog Input Voltage (VNO, VNC, or VCOM)
VIN
Digital Select Input Voltage
Ianl1
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Defined as 10% ON, 90% off duty cycle.
RECOMMENDED OPERATING CONDITIONS
Symbol
Rating
Min
Max
Unit
1.65
5.5
V
VCC
Positive DC Supply Voltage
VIS
Analog Input Voltage (NC, NO, COM)
0
VCC
V
VIN
Digital Select Input Voltage (IN)
0
VCC
V
TA
Operating Temperature Range
−40
85
°C
tr, tf
Input Rise or Fall Time, SELECT
20
10
ns/V
VCC = 3.0 V
VCC = 5.5 V
http://onsemi.com
2
NLAS5123
DC ELECTRICAL CHARACTERISTICS
Symbol
Parameter
VCC
(V)
Test Conditions
VIH
HIGH Level
Input Voltage
2.7
4.5
VIL
LOW Level
Input Voltage
2.7
4.5
IIN
Input Leakage Current
0 v VIN v 5.5 V
IOFF
OFF State Leakage
Current (Note 7)
0 v NO, NC, COM v VCC
5.5
ION
ON State Leakage
Current (Note 7)
0 v NO, NC, COM v VCC
5.5
RON
Switch On Resistance
(Note 2)
IO = 100 mA,
VIS = 0 V to VCC
ICC
TA = +25°C
Min
Typ
TA = −40°C to +85°C
Max
Min
Max
2.0
2.4
Unit
V
0.6
0.8
V
±0.1
±1
A
−2.0
+2.0
±20
nA
−4.0
+4.0
±40
nA
2.7
1.7
2.0
IO = 100 mA,
VIS = 0 V to VCC
4.5
1.0
1.2
VIN = VCC or GND, IOUT = 0
5.5
0.5
1.0
On Resistance Match
Between Channels
(Notes 2, 3, 4)
IA = 100 mA,
VIS = 1.5 V
IA = 100 mA,
VIS = 2.5 V
2.7
0.15
4.5
0.12
On Resistance
Flatness (Notes 2, 3, 5)
IA = 100 mA,
VIS = 0 V to VCC
IA = 100 mA,
VIS = 0 V to VCC
2.7
0.4
4.5
0.3
Quiescent Supply
Current
All Channels ON or OFF
0−5.5
A
Analog Signal Range
RON
Rflat
0.15
0.4
2. Measured by the voltage drop between NC/NO and COM pins at the indicated current through the switch. On Resistance is determined by
the lower of the voltages on the two (NO, NC, COM).
3. Parameter is characterized but not tested in production.
4. RON = RON max − RON min measured at identical VCC, temperature and voltage levels.
5. Flatness is defined as the difference between the maximum and minimum value of On Resistance over the specified range of conditions.
6. Guaranteed by Design.
7. This parameter is guaranteed by design but not tested. The bus switch contributes no propagation delay other than the RC delay of the On
Resistance of the switch and the 50 pF load capacitance, when driven by an ideal voltage source (zero output impedance).
http://onsemi.com
3
NLAS5123
AC ELECTRICAL CHARACTERISTICS
Symbol
Parameter
Test Conditions
VCC
(V)
TA = +25°C
Min
Typ
TA = −40°C to +85°C
Max
Min
Max
tPHL
tPLH
Propagation Delay
Bus−to−Bus (Note 9)
VIN = VIH or VIL
2.7
4.5
2.0
0.3
tON
Output Enable Time
Turn On Time
(COM to NO or NC)
VIS = 1.5 V,
RL = 50 , CL = 35 pF
VIS = 3.0 V,
RL = 50 , CL = 35 pF
2.7
30
35
4.5
20
25
Output Disable Time
Turn Off Time
(COM to NO, NC)
VIS = 1.5V,
RL = 50 , CL = 35 pF
VIS = 3.0 V,
RL = 50 , CL = 35 pF
2.7
20
25
4.5
15
20
Break Before Make Time
(Note 8)
VIS = 1.5V,
RL = 50 , CL = 35 pF
tOFF
tBBM
Q
Charge Injection
(Note 8)
CL = 1.0 nF, VGEN = 0 V
RGEN = 0 OIRR
Off Isolation (Note 10)
Xtalk
Unit
Figure
#
ns
2.7
0.5
0.5
4.5
0.5
0.5
ns
3, 4
ns
3, 4
ns
2
2.7
4.5
26
48
pC
6
RL = 50 f = 1.0 MHz
2.7 −
5.5
−62
dB
5
Crosstalk
RL = 50 f = 1.0 MHz
2.7 −
5.5
−70
dB
7
BW
−3 dB Bandwidth
RL = 50 2.7 −
5.5
55
MHz
8
THD
Total Harmonic
Distortion (Note 8)
RL = 600 0.5 VP−P
f = 20 Hz to 20 kHz
2.7 −
5.5
0.012
%
9
8. Guaranteed by Design.
9. This parameter is guaranteed by design but not tested. The bus switch contributes no propagation delay other than the RC delay of the On
Resistance of the switch and the 50 pF load capacitance, when driven by an ideal voltage source (zero output impedance).
10. Off Isolation = 20 log10 [VCOM/VNO,NC].
CAPACITANCE (Note 11)
Symbol
Parameter
Test Conditions
Typ
Max
Unit
CIN
Select Pin Input Capacitance
VCC = 0 V, f = 1 MHz
2.0
pF
CNC/NO
NC, NO Port Off Capacitance
VCC = 4.5 V, f = 1 MHz
20
pF
CCOM
COM Port Capacitance when Switch is Enabled
VCC = 4.5 V, f = 1 MHz
55
pF
11. TA = +25°C, f = 1 MHz, Capacitance is characterized but not tested in production.
http://onsemi.com
4
NLAS5123
VCC
DUT
VCC
Input
Output
GND
VOUT
0.1 F
50 tBMM
35 pF
90%
90% of VOH
Output
Switch Select Pin
GND
Figure 2. tBBM (Time Break−Before−Make)
VCC
Input
DUT
VCC
0.1 F
50%
Output
VOUT
Open
50%
0V
50 VOH
90%
35 pF
90%
Output
VOL
Input
tON
tOFF
Figure 3. tON/tOFF
VCC
VCC
Input
DUT
Output
50%
0V
50 VOUT
Open
50%
VOH
35 pF
Output
Input
tOFF
Figure 4. tON/tOFF
http://onsemi.com
5
10%
10%
VOL
tON
NLAS5123
50 DUT
Reference
Transmitted
Input
Output
50 Generator
50 Channel switch control/s test socket is normalized. Off isolation is measured across an off channel. On loss is
the bandwidth of an On switch. VISO, Bandwidth and VONL are independent of the input signal direction.
ǒVVOUT
Ǔ for VIN at 100 kHz
IN
VOUT
Ǔ for VIN at 100 kHz to 50 MHz
VONL = On Channel Loss = 20 Log ǒ
VIN
VISO = Off Channel Isolation = 20 Log
Bandwidth (BW) = the frequency 3 dB below VONL
VCT = Use VISO setup and test to all other switch analog input/outputs terminated with 50 Figure 5. Off Channel Isolation/On Channel Loss (BW)/Crosstalk
(On Channel to Off Channel)/VONL
DUT
VCC
VIN
Output
Open
GND
CL
Output
Off
VIN
Figure 6. Charge Injection: (Q)
http://onsemi.com
6
On
Off
VOUT
NLAS5123
0
0
−10
−0.5
−20
−1
−1.5
−40
BW (dB)
XT (dB)
−30
−50
−60
−2
−2.5
−3
−70
−80
−3.5
−90
−4
−100
0.01
0.1
1
10
−4.5
0.01
100
0.1
FREQUENCY (MHz)
Figure 8. Bandwidth vs. Frequency
0.01
1.9
0.009
1.7
0.008
85°C
1.5
0.007
0.006
RON ()
THD (%)
100
FREQUENCY (MHz)
Figure 7. Cross Talk vs. Frequency
@ VCC = 4.5 V
0.005
0.004
0.003
25°C
1.3
1.1
−40°C
0.9
0.002
0.7
0.001
0
10
100
1000
10000
100000
0.5
0
0.5
1
1.5
2
2.5
FREQUENCY (Hz)
VIS (V)
Figure 9. Total Harmonic Distortion
Figure 10. On−Resistance vs. Input Voltage
@ VCC = 2.7 V
1.2
3
1.6
1
85°C
0.8
25°C
2.7 V
1.4
RON ()
RON ()
10
1
−40°C
0.6
0.4
3.0 V
1.2
1.0
3.6 V
4.5 V
0.8
0.2
5.5 V
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
0.6
4.5
0
1
2
3
4
5
VIS (V)
VIS (V)
Figure 11. On−Resistance vs. Input Voltage
@ VCC = 4.5 V
Figure 12. On−Resistance vs. Input Voltage
http://onsemi.com
7
6
NLAS5123
DEVICE ORDERING INFORMATION
Device Nomenclature
Circuit
Indicator
Technology
Device
Function
Package
Suffix
Tape & Reel
Suffix
NLAS5123MNR2G
NL
AS
5123
MN
NLAS5123MUR2G
NL
AS
5123
MU
Device Order Number
Package Type
Tape & Reel Size†
2
WDFN6
(Pb−Free)
3000 / Tape & Reel
2
UDFN6
(Pb−Free)
3000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
8
NLAS5123
PACKAGE DIMENSIONS
UDFN6, 1.2x1.0, 0.4P
CASE 517AA−01
ISSUE C
EDGE OF PACKAGE
PIN ONE
REFERENCE
2X
0.10 C
L1
ÉÉ
ÉÉ
ÉÉ
E
DETAIL A
Bottom View
(Optional)
TOP VIEW
2X
EXPOSED Cu
0.10 C
(A3)
0.10 C
A1
A
10X
0.08 C
ÉÉÉ
ÉÉÉ
A3
DETAIL B
Side View
(Optional)
5X
MILLIMETERS
MIN
MAX
0.45
0.55
0.00
0.05
0.127 REF
0.15
0.25
1.20 BSC
1.00 BSC
0.40 BSC
0.30
0.40
0.00
0.15
0.40
0.50
MOUNTING FOOTPRINT*
6X
C
A1
DIM
A
A1
A3
b
D
E
e
L
L1
L2
MOLD CMPD
SEATING
PLANE
SIDE VIEW
1
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED TERMINAL
AND IS MEASURED BETWEEN 0.25 AND
0.30 mm FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
A
B
D
6X
0.42
0.22
L
3
L2
6X
b
0.10 C A B
0.05 C
6
4
0.40
PITCH
e
NOTE 3
1.07
DIMENSIONS: MILLIMETERS
BOTTOM VIEW
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
9
NLAS5123
PACKAGE DIMENSIONS
WDFN6 1.2x1.0, 0.4P
CASE 506AS−01
ISSUE C
D
L
A
B
L
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.25 AND 0.30mm FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
L1
ÍÍÍ
ÍÍÍ
PIN ONE
REFERENCE
0.10 C
2X
2X
DETAIL A
ALTERNATE TERMINAL
CONSTRUCTIONS
E
ÉÉÉ
ÉÉÉ
EXPOSED Cu
0.10 C
DETAIL B
DETAIL B
0.10 C
MOLD CMPD
DIM
A
A1
A3
b
D
E
e
L
L1
L2
ÉÉÉ
ÇÇÇ
ÇÇÇ
A3
A1
ALTERNATE
CONSTRUCTIONS
A3
MILLIMETERS
MIN
MAX
0.70
0.80
0.00
0.05
0.20 REF
0.15
0.25
1.20 BSC
1.00 BSC
0.40 BSC
0.30
0.40
0.00
0.15
0.40
0.50
MOUNTING FOOTPRINT*
A
6X
6X
0.42
7X
0.08 C
0.22
A1
C
SEATING
PLANE
4X
DETAIL A
e
1
5X
L
3
L2
0.40
PITCH
1.07
DIMENSIONS: MILLIMETERS
6
4
BOTTOM VIEW
b
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
6X
0.10 C A
0.05 C
B
NOTE 3
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
10
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NLAS5123/D