ACAS 0606 ATAU - Precision www.vishay.com Vishay Beyschlag Precision Gold Terminated Thin Film Chip Resistor Array for Conductive Gluing FEATURES • Gold terminations for conductive gluing • Superior moisture resistivity, |R/R| < 0.5 % (85 °C; 85 % RH; 1000 h) • Rated dissipation P70 up to 125 mW per resistor • ESD stability 1000 V, human body model The ACAS 0606 AT precision resistor array with convex terminations for conductive gluing combines the proven reliability of discrete chip resistors with the advantages of chip resistor arrays. Defined relative tolerance and relative TCR make this product perfectly suited for applications that require stable fixed resistor ratios. The ACAS 0606 AT is available with two equal or two different resistor values. • Relative TCR down to ± 5 ppm/K • Relative tolerance down to ± 0.05 % • AEC-Q200 qualified • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS • Precision analog circuits • Voltage divider • Feedback circuits • Signal conditioning • Hybrid circuits TECHNICAL SPECIFICATIONS DESCRIPTION EIA size Metric size Configuration, isolated ACAS ATAU 0606 RR 1616M 2 x 0603 Design: All equal values (AE) AE Different values (DF) DF Resistance range 100 to 150 k (1) Absolute tolerance ± 0.5 %; ± 0.25 % Relative tolerance ± 0.05 %; ± 0.125 %; ± 0.25 % Absolute temperature coefficient Relative TCR Max. resistance ratio Rmin./Rmax. 25 ppm/K ± 5 ppm/K; ± 7.5 ppm/K± 12.5 ppm/K 1:20 Rated dissipation: P70 Element 0.125 W Package 0.2 W Operating voltage, Umax. AC/DC 75 V Permissibe film temperature 155 °C Operating temperature range -55 °C to 155 °C Insulation voltage (Uins) against ambient and between integrated resistors, continuous 75 V Note (1) Resistance values to be selected from E24; E192. Revision: 27-Jun-14 Document Number: 28876 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 ACAS 0606 ATAU - Precision www.vishay.com Vishay Beyschlag APPLICATION INFORMATION The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature is not exceeded. These resistors do not feature a limited lifetime when operated within the permissible limits. MAXIMUM RESISTANCE CHANGE AT RATED POWER DESCRIPTION ACAS ATAU Configuration, isolated 2 x 0603 Operation mode Standard Power Rated power per element, P70 0.1 W 0.125 W Rated power per package, P70 0.15 W 0.2 W Film temperature 125 °C 155 °C 550 K/W 680 K/W 1000 h ± 0.1 % ± 0.25 % 8000 h ± 0.25 % ± 0.5 % Required thermal resistance, Rth Max. resistance change at P70 R/R max., after: Notes • Figures are given for arrays with equal values, design type AE. • An appropriate thermal resistance Rth has to be realized by adequate gluing connection and board material. SKETCHES 4 3 R1 Pin 1 R2 2 ACAS ATAU Marking on ACAS ATAU: For types with different resistor values pin 1 is marked. DESIGN TYPE ACAS ATAU AE R1 = R2 DF R1 < R2 Revision: 27-Jun-14 Document Number: 28876 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 ACAS 0606 ATAU - Precision www.vishay.com Vishay Beyschlag PART NUMBER AND PRODUCT DESCRIPTION Part Number: ACASN1100A2200P50A A C A S N 1 1 0 TYPE TERMINAL SIZE RESISTANCE ACA S = Convex square N = 0606 3 digit resistance value R1, R4 1 digit multiplier 0 A 2 ACCURACY GRADE 2 0 0 P 5 0 A RESISTANCE PACKAGING Special 3 digit resistance value R2, R3 1 digit multiplier P1 P5 0A = Gold termination TCR, Tracking, Tolerance and Matching A, E or J MULTIPLIER 9 = *10-1 0 = *100 1 = *101 2 = *102 3 = *103 MULTIPLIER 9 = *10-1 0 = *100 1 = *101 2 = *102 3 = *103 Product Description: ACAS 0606 110R A 220R ATAU P5 ACA S 0606 110R A 220R ATAU P5 TYPE TERMINAL SIZE RESISTANCE R1, R4 ACCURACY GRADE RESISTANCE R2, R3 SPECIAL PACKAGING ACA = Chip Array S = Convex square 0606 110R = 110 1K1 = 1.1 k 22K1 = 22.1 k TCR, Tracking, Tolerance and Matching A, E or J 220R = 220 1K1 = 1.1 k 22K1 = 22.1 k ATAU = Automotive/ gold termination P1 P5 Note • Products can be ordered using either the PART NUMBER or PRODUCT DESCRIPTION. TEMPERATURE COEFFICIENT AND RESISTANCE RANGE TYPE ACAS 0606 ATAU ACCURACY GRADE ABSOLUTE RELATIVE RESISTANCE RANGE TCR TOLERANCE TCR TOLERANCE A ± 25 ppm/K ± 0.25 % ± 5 ppm/K ± 0.05 % 100 to 150 k E ± 25 ppm/K ± 0.25 % ± 7.5 ppm/K ± 0.05 % 100 to 150 k J ± 25 ppm/K ± 0.25 % ± 12.5 ppm/K ± 0.05 % 100 to 150 k PACKAGING TYPE CODE QUANTITY P1 1000 P5 5000 ACAS 0606 ATAU Revision: 27-Jun-14 PACKAGING STYLE WIDTH PITCH REEL DIAMETER Tape and reel cardboard tape acc. IEC 60286-3 Type I 8 mm 4 mm 180 mm/7" Document Number: 28876 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 ACAS 0606 ATAU - Precision www.vishay.com Vishay Beyschlag DIMENSIONS ACAS 0606 ATAU W A Pin 4 Pin 3 Tb L Tt H Pin 1 A1 Pin 2 DIMENSIONS - chip resistor array, mass and relevant physical dimensions TYPE ACAS 0606 ATAU L (mm) W (mm) H (mm) A1 (mm) A (mm) Tt (mm) Tb (mm) MASS (mg) 1.5 0.15 1.6 0.15 0.45 0.1 0.6 0.1 0.4 0.1 0.3 0.15 0.4 0.15 3.6 DESCRIPTION ASSEMBLY The ACAS 0606 ATAU series for conductive gluing is derived from the precision ACAS 0606 ATAU series, datasheet number 28770, which is qualified according AEC-Q200. The ACAS 0606 ATAU series for conductive gluing is manufactured identically except the termination. The production of the components is strictly controlled and follows an extensive set of instructions established for reproducibility. A homogeneous film of metal alloy is deposited on a high grade ceramic substrate using a mask to separate the adjacent resistors and conditioned to achieve the desired temperature coefficient. Specially designed inner contacts are realized on both sides. A special laser is used to achieve the target value by smoothly cutting a meander groove in the resistive layer without damaging the ceramics. The resistors are suitable for processing on automatic SMD assembly systems. They are suitable for conductive gluing technology. The encapsulation is resistant to all cleaning solvents commonly used in the electronics industry, including alcohols, esters and aqueous solutions. The resistor elements are covered by a protective coating designed for electrical, mechanical and climatic protection. The termination recieve a final layer appropriate for conductive gluing. The result of the determined production is verified by an extensive testing procedure and optical inspection performed on 100 % of the individual chip resistors. Only accepted products are laid directly into the paper tape in accordance with IEC 60286-3 (3). The suitability of conformal coatings, if applied, shall be qualified by appropriate means to ensure the long-term stability of the whole system. The chip arrays are RoHS compliant. All products comply with the GADSL (1) and the CEFIC-EECA-EICTA (2) list of legal restrictions on hazardous substances. This includes full compliance with the following directives: • 2000/53/EC End of Life Vehicle Directive (ELV) and Annex II (ELV II) • 2011/65/EU Restriction of the use of Hazardous Substances directive (RoHS) • 2002/96/EC Waste Electrical and Electronic Equipment Directive (WEEE) RELATED PRODUCTS Chip resistors for conductive gluing may be used in high temperature applications. For more information please refer to the MC ATAU - Precision datasheet (www.vishay.com/doc?28877). Notes (1) Global Automotive Declarable Substance List, see www.gadsl.org. (2) CEFIC (European Chemical Industry Council), EECA (European Electronic Component Manufacturers Association), EICTA (European trade organisation representing the information and communications technology and consumer electronics), see www.eicta.org policy environmental policy group chemicals jig Joint Industry Guide (JIG-101 Ed 2.0). (3) The quoted IEC standards are also released as EN standards with the same number and identical contents. Revision: 27-Jun-14 Document Number: 28876 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 ACAS 0606 ATAU - Precision www.vishay.com Vishay Beyschlag Rated Power in % FUNCTIONAL PERFORMANCE Power Mode Standard Mode 100 80 60 40 20 0 - 55 0 50 70 100 125 155 180 Ambient Temperature in °C For permissible resistance change please refer to table MAXIMUM RESISTANCE CHANGE AT RATED POWER, above Derating TESTS AND REQUIREMENTS The tests are are carried out under standard atmospheric conditions according to IEC 60068-1 (1), 5.3. Climatic category LCT/UCT/56 (rated temperature range: Lower category temperature, upper category temperature; damp heat, long term, 56 days) is valid (LCT = - 55 °C/UCT = 125 °C). Unless otherwise specified the following values apply: Temperature: 15 °C to 35 °C Relative humidity: 45 % to 75 % Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar) TEST PROCEDURES AND REQUIREMENTS EN 60 115-1 CLAUSE IEC 60 068-2 (1) TEST METHOD TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (2) (R) Stability for product types: ACAS 0606 ATAU 100 to 150 k 4.5 - Resistance - 0.5 % R; 0.25 % R 4.8.4.2 - Temperature coefficient At (20/- 55/ 20) °C and (20/125/20) °C 50 ppm/K; 25 ppm/K U = P 70 x R or U = Umax.; 1.5 h on; 0.5 h off; whichever is less severe Endurance at 70 °C: Standard operation mode 4.25.1 - (0.1 % R + 0.05) ± (0.05 % R + 0.05) 8000 h: Absolute Relative (0.25 % R + 0.05) ± (0.125 % R + 0.05) U = P 70 x R or U = Umax.; 1.5 h on; 0.5 h off; whichever is less severe Endurance at 70 °C: Power operation mode Revision: 27-Jun-14 1000 h: Absolute Relative 1000 h: Absolute Relative ± (0.25 % R + 0.05) ± (0.125 % R + 0.05) 8000 h: Absolute Relative ± (0.5 % R + 0.05) ± (0.25 % R + 0.05) Document Number: 28876 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 ACAS 0606 ATAU - Precision www.vishay.com Vishay Beyschlag TEST PROCEDURES AND REQUIREMENTS EN 60 115-1 CLAUSE IEC 60 068-2 (1) TEST METHOD TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (2) (R) Stability for product types: ACAS 0606 ATAU 4.25.3 - Endurance at upper category temperature 100 to 150 k 125 °C; 1000 h: Absolute Relative ± (0.25 % R + 0.05 ) ± (0.125 % R + 0.05) 125 °C; 8000 h: Absolute Relative ± (0.5 % R + 0.05 ) ± (0.25 % R + 0.05) 155 °C; 1000 h: Absolute Relative (0.4 % R + 0.05 ) ± (0.2 % R + 0.05) 78 (Cab) Damp heat, steady state (40 2)C; 56 days; (93 3) % RH (0.25 % R + 0.05) 4.39 67 (Cy) Damp heat, steady state, accelerated (85 ± 2) °C (85 ± 5) % RH U = 0.1 x P 70 x R 100 V; 1000 h (0.5 % R + 0.05) 4.13 - Short time overload: Standard operation mode (3) U = 2.5 x P 70 x R or U = 2 x Umax.; whichever is less severe; 5s (0.1 % R + 0.01) no visible damage 4.40 - Electrostatic discharge (human body model) (3) IEC 61340-3-1; 3 pos. + 3 neg. (equivalent to MIL-STD-883, Method 3015); 1000 V (0.5 % R + 0.05) 4.24 Notes (1) The quoted IEC standards are also released as EN standards with the same number and identical contents. (2) Figures are given for arrays with equal values, design type AE. (3) For a single element. Revision: 27-Jun-14 Document Number: 28876 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000