AK4183VT

[ASAHI KASEI]
[AKD4183]
AKD4183
AK4183 Rev.A Evaluation Board
Abstract
AKD4183 is the board for evaluation of the touch screen controller AK4183 which adopted the TMSOP small
package suitable for the cellular phone, the handheld game machine, etc. Since AKD4183 has a touch-panel
I/F and a digital I/O power supply input terminal, it is easily connectable with a target system of low
power/voltage drive.
Function
„ AK4183 (TMSOP 10 package)
„ I2C I/F for uP
„ Touch-panel I/F
„ Digital I/O power supply terminal
Touch Panel I/F
I2C I/F
VCC
AGND
AIN_XP
AK4183
IFVDD
AIN_XN
DGND
YN
XN
Figure 1 AKD4183 Block Diagram
„ Operation procedure
1. Wiring of a power supply
VCC (Red) =2.5V∼3.6V
AGND (Black) = 0V
DGND (Black) = 0V
IFVDD (Orange) = VCC
JP1-short (default: CAD0pin = “L”), JP2-short
2. A setup of I2C address J1 (short: CAD0pin =”L“, open: CAD0pin = ”H“)
3. Connect I2C I/F (SCL, SDA) to uP.
4. A setup of evaluation mode, jumper
5. Power supply ON
6. Run the control soft
„ Evaluation mode selection
1) Position, Pen Pressure
4 wire touch-panel (X+, X-, Y+, and Y-) is connected to J1 connector.
Jumper setup
JP3 (XPSEL) ---------select XP
JP4 (YPSEL) ---------select YP
JP5 (XNSEL) ---------select XN
JP6 (YNSEL) ---------select YN
„ Power supply injection, Evaluation
1) Digital serial data input
When the control command data indicated by specification from digital I/F (P1 or PORT1) was inputted the AD
conversion is carried out and is outputted from a SDA.
„ Parallel Port Driver install
Attached software is the application software which checks the function of the AK4183. Windows(R) Win98, Win2K,
and WinXP are supported. However, to make it operate on Win2K and XP, it is necessary to install driver in advance.
Please follow a procedure with reference to DriverSetupe.pdf. Installation of a driver is unnecessary to use it by the
Windows 98 system.
<KM085700>
2006/9
-1-
[ASAHI KASEI]
[AKD4183]
„ Run the software (AK4183_070.exe)
First match Port Address of your PC environment. Measurements are started when the start button is clicked after select
Channel Selection, MODE, and Power Down 0. A result will be displayed on AD OUT Section. When carrying out
position detection, the position where pen clicked on the touch panel is measured.
Operation can set up two control commands. Continuation operation can be performed. Each data (mean, max, and min)
is also displayed at the same time. PENIRQN can be seen by the break of a command.
<KM085700>
2006/9
-2-
[ASAHI KASEI]
[AKD4183]
„ Trouble Shooting
1. Application error is occurred and doesn’t start up
If the operating system is Window2000/X, Please install AKMport driver in advance of run the
AK4183_070.exe.
2. MEAN value in AD OUT section does not change when click start button (cannot write control command to
AK4183)
Please set the port address to your PC platform environment.
3. The mean, max, min value doesn't change wherever the pen pushes down on the panel.
There is a possibility of the trouble of the contact of the relay connector (plat 8pin-8-wire female dip converter)
that connects the touch panel. Please open JP3, 4, 5, and 6 on the evaluation board, measure panel seat resistance
(XP-XN, YP-YN), and check the resistance. Generally, the panel seat resistance is hundreds of Ω. There is a
possibility that the touch panel is not correctly connected if the resistance is over thousands of kΩ. Please
connect the relay connector and check the resistance value again.
<KM085700>
2006/9
-3-
[ASAHI KASEI]
[AKD4183]
Revision History
Date
(YY/MM/DD)
06/09/22
Manual
Revision
KM085700
Board
Revision
0
Reason
Contents
First edition
IMPORTANT NOTICE
• These products and their specifications are subject to change without notice. Before considering any
use or application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM) sales office or authorized
distributor concerning their current status.
• AKM assumes no liability for infringement of any patent, intellectual property, or other right in the
application or use of any information contained herein.
• Any export of these products, or devices or systems containing them, may require an export license
or other official approval under the law and regulations of the country of export pertaining to customs
and tariffs, currency exchange, or strategic materials.
• AKM products are neither intended nor authorized for use as critical components in any safety, life
support, or other hazard related device or system, and AKM assumes no responsibility relating to
any such use, except with the express written consent of the Representative Director of AKM. As
used here:
(a) A hazard related device or system is one designed or intended for life support or maintenance of
safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its
failure to function or perform may reasonably be expected to result in loss of life or in significant
injury or damage to person or property.
(b) A critical component is one whose failure to function or perform may reasonably be expected to
result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or
system containing it, and which must therefore meet very high standards of performance and
reliability.
• It is the responsibility of the buyer or distributor of an AKM product who distributes, disposes of, or
otherwise places the product with a third party to notify that party in advance of the above content
and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability
for and hold AKM harmless from any and all claims arising from the use of said product in the
absence of such notification.
<KM085700>
2006/9
-4-
5
4
3
2
1
1
VCC
D1
LED(Red)
R3
10k
U1A
74LVC07
1
DGND
2
2
1
SCLW
1
51
DGND
DGND
PORT1
YPSEL
2
3
51
C4
open
0
DGND
6
5
R11
2
C6
1
1
R17
10k
C5
0.1u
U1D
CN1
U3
8
DGND
PENIRQN
1
8
2
4
6
10
12
15
CN2
1
2
3
4
5
単面
外
内
10
9
8
7
6
SCLW
SDAW
CN1
2
U1F
13
XP_T
R22
1
R23
1
R24
1
R25
1
C10
0.1u
12
74LVC07
J1
DGND
for SN74LVC07A
部品:エルボーTerminal(支給)
VCC
R21
2
3
4
5
51
A
AIN_YP
2
51
47k
51
2
2
2
47k
B
DGND
2
CONNECTOR DB25
2
2
AGND
JP7
2
1
2
3
4
BNCXP
IFVDD
1
AGND
AGND
DGND
DGND
YN
XN
YN
バナナジャック
DGND
CL1
2
5
6
7
8
XN
1
1
VCC
1
47k
1
AIN_XP
1
51
2
2
1
2
3
4
5
1
R20
47k
IFVDD
1
VCC
U1の組み合わせは
入れ替え可です
1
51
P1
DGND
J2
J3
51
IFVDD
1
XN_T
R15
1
R16
1
R18
1
R19
1
PENIRQN
SDAR
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
14
1
IFVDD
74LVC07
CN2
16
13
3
5
7
9
11
14
NC2
NC1
A1
A2
A3
A4
A5
A6
74HC4050
10
YP_T
AGND
VT
DGND
Y1
Y2
Y3
Y4
Y5
Y6
U1E
11
YN_T
2
51
IFVDD
74LVC07
B
DGND
2
IFVDD
TP10
PENIRQN
2
51
74LVC07
9
Touch Screen
8 8
7 7
6 6
5 5
4 4
3 3
2 2
1 1
1
SDAR_1
AGND
AGND
R8
PENIRQN_1
SDAW
1
YNSEL
1
0.001u
3
2
2
C9
R14
2 1
0.001u
1
YN
JP6
C8
2
1
YN_T
AGND
2
C7
XNSEL
AGND
C
51
1
1
2
0
DGND
EX_CONTW2
2
R13
2 1
EX_CONTW1
U1C
1
0.001u
JP5
3
SDAR
R6
AK4183
XN
1
0.001u
1
XN_T
4
74LVC07
26
CAD0
P_SDAR
U1B
R12
1
2
10
9
8
7
6
DGND
P_SDAW
0
VCC
SCL
XP
SDA
YP
CAD0
XN PENIRQN
YN
GND
TP3
EXTR1
DI_SCL
DI_SDA
4183I/F
R10
10k
2
1
2
3
4
5
2
R9
10k
2
R7
2 1
5
4
3
2
1
1
TP9
SDA
U2
JP4
1
C2
4.7u
2
C
IFVDD
0
XPSEL
DI_SDA
VCC
1
1
+
AGND
1
3
2
BNCYP
2
1
YP_T
1
R4
2 1
0.1u
3
2
1
2
XP_T
BNCXP
C1
1
P_SDAW
JP2
ICC
JP3
6
7
8
9
10
P_SCLW
1
Tantalum
P_SCLW
ceramic
VCC
1-5pin 基板端面
TP1
EXTW1
TP2
EXTW2
27
C3
open
2
SUB基板接続点
1
AGND
D
EX_CONTR1
2
1
2
R5
R2
1k
1
JP1
CAD0
TP7
XP
1
1
TP6
YP
1
TP5
XN
1
TP4
YN
14
1
CAD0
DI_SCL
IFVDD
1
2
VCC
TP8
SCL
2
R1
10k
AGND
7
Analog Workspace(Universal area)
VCC
D
1 2
1
VCC
1
CL2
2
BNCYP
1
CL3
2
AINSEL
1
A
CL4
2
AGND
1
HARTEC
Cut Land Short
PART
NO
AGND
DGND
1.0
Rev.
5
4
3
2
20294
2005.11.16
Date
Modify Page
Title
䎤䎮䎗䎔䎛䎖䎃䎨䏙䏄䏏䏘䏄䏗䏌䏒䏑䎃䎥䏒䏄䏕䏇
Size
A3
Sub Title
Rev
1.0
䎟䎧䏒䏆䎡
DESIGNER
2005.11.16
CHECKED
APPROVED
Date:
Wednesday, November 16, 2005
1
KIMURA
Sheet
1
/
1