A3230 Chopper-Stabilized Hall-Effect Bipolar Switch Discontinued Product This device is no longer in production. The device should not be purchased for new design applications. Samples are no longer available. Date of status change: December 3, 2013 Recommended Substitutions: For existing customer transition, and for new customers or new applications, refer to the Allegro A1250. NOTE: For detailed information on purchasing options, contact your local Allegro field applications engineer or sales representative. Allegro MicroSystems, LLC reserves the right to make, from time to time, revisions to the anticipated product life cycle plan for a product to accommodate changes in production capabilities, alternative product availabilities, or market demand. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use; nor for any infringements of patents or other rights of third parties which may result from its use. A3230 Chopper-Stabilized Hall-Effect Bipolar Switch Features and Benefits Description ▪ Chopper stabilization ▫ Superior temperature stability ▫ Extremely low switchpoint drift ▫ Insensitive to physical stress ▪ Reverse battery protection ▪ Output short circuit protection ▪ Solid state reliability ▪ Small size ▪ Robust EMC capability ▪ High ESD ratings (HBM) The A3230 Hall-effect sensor IC is a temperature stable, stress-resistant bipolar switch. This device is the most sensitive Hall-effect device in the Allegro™ bipolar switch family and is intended for ring-magnet sensing. Superior high-temperature performance is made possible through an Allegro patented dynamic offset cancellation that utilizes chopper-stabilization. This method reduces the offset voltage normally caused by device overmolding, temperature dependencies, and thermal stress. The A3230 includes the following on a single silicon chip: a voltage regulator, Hall-voltage generator, small-signal amplifier, chopper stabilization, Schmitt trigger, and a short circuit protected open-drain output. Advanced BiCMOS wafer fabrication processing takes advantage of low-voltage requirements, component matching, very low input-offset errors, and small component geometries. Packages: 3 pin SOT23W (suffix LH), and 3 pin SIP (suffix UA) The A3230 Hall-effect bipolar switch turns on in a south polarity magnetic field of sufficient strength and switches off in a north polarity magnetic field of sufficient strength. Because the output state is not defined if the magnetic field is Continued on the next page… Not to scale Functional Block Diagram VCC Regulator Low-Pass Filter Amp Sample and Hold Dynamic Offset Cancellation To All Subcircuits VOUT Control Current Limit <1Ω GND 3230-DS, Rev. 9 A3230 Chopper-Stabilized Hall Effect Bipolar Switch Description (continued) diminished or removed, to ensure that the device switches, Allegro recommends using magnets of both polarities and of sufficient strength in the application. The A3230 is rated for operation between the ambient temperatures –40°C and 85°C for the E temperature range, and –40°C to 150°C for the L temperature range. Two A3230 package styles provide magnetically optimized solutions for most applications. Package LH is a SOT23-W, a miniature low-profile surface-mount package, while package UA is a three-lead ultramini SIP for through-hole mounting. Each package is available in a lead (Pb) free version, with 100% matte tin plated leadframes. Selection Guide Packing1 Part Number A3230LLHLT-T2 A3230LUA-T2 1Contact Allegro Mounting 7-in. reel, 3000 pieces/reel Bulk, 500 pieces/bag 3-pin SOT23W surface mount 3-pin SIP through hole Ambient, TA (°C) BRP(MIN) (G) BOP(MAX) (G) –40 to 150 –25 25 for additional packing options. 2Variant is in production but has been determined to be NOT FOR NEW DESIGN. This classification indicates that sale of the variant is currently restricted to existing customer applications. The variant should not be purchased for new design applications because obsolescence in the near future is probable. Samples are no longer available. Status date change January 30, 2012. Absolute Maximum Ratings Characteristic Symbol Notes Rating Units Supply Voltage VCC 28 V Reverse Supply Voltage VRCC –18 V VOUT 26.5 V IOUTSINK Internally Limited – IROUT –10 mA B Unlimited G Range E –40 to 85 ºC Range L Output Off Voltage Output Current Reverse-Output Current Magnetic Flux Density Operating Ambient Temperature TA –40 to 150 ºC Maximum Junction Temperature TJ(max) 165 ºC Tstg –65 to 170 ºC Storage Temperature Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 2 A3230 Chopper-Stabilized Hall Effect Bipolar Switch OPERATING CHARACTERISTICS valid over full operating voltage and ambient temperature ranges, unless otherwise noted Characteristic Symbol Test Conditions Min. Typ. Max. Units Electrical Characteristics Supply Voltage1 Output Leakage Current VCC Operating, TJ < 165°C 3.6 – 24 V IOUTOFF VOUT = 24 V, B < BRP – – 10 μA VOUT(SAT) IOUT = 20 mA, B > BOP – 250 500 mV Output Current Limit IOM B > BOP 30 – 60 mA Power-On Time tPO VCC > 3.6 V Output On Voltage – 8 50 μs – 200 – kHz RLOAD = 820 Ω, CS = 20 pF – 0.2 1 μs RLOAD = 820 Ω, CS = 20 pF – 0.2 1 μs ICCON B > BOP – 1.6 3.5 mA ICCOFF B < BRP – 1.6 3.5 mA VRCC = –18 V – – –2 mA VZ ICC = 6.5 mA; TA = 25°C 28 – – V IZ VS = 28 V – – 6.5 mA Chopping Frequency fc Output Rise Time2 tr Output Fall Time2 tf Supply Current Reverse Battery Current Supply Zener Clamp Voltage Supply Zener Current3 IRCC Magnetic Characteristics4 Operate Point BOP South pole adjacent to branded face of device –10 7.5 25 G Release Point BRP North pole adjacent to branded face of device –25 –7.5 10 G Hysteresis BHYS BOP – BRP 5 15 25 G 1 Maximum voltage must be adjusted for power dissipation and junction temperature, see Power Derating section. 2 C = oscilloscope probe capacitance. S 3 Maximum current limit is equal to the maximum I CC(MAX) + 3 mA. 4 Magnetic flux density, B, is indicated as a negative value for north-polarity magnetic fields, and as a positive value for south-polarity magnetic fields. This so-called algebraic convention supports arithmetic comparison of north and south polarity values, where the relative strength of the field is indicated by the absolute value of B, and the sign indicates the polarity of the field (for example, a –100 G field and a 100 G field have equivalent strength, but opposite polarity). DEVICE QUALIFICATION PROGRAM Contact Allegro for information. EMC (Electromagnetic Compatibility) REQUIREMENTS Contact Allegro for information. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 3 A3230 Chopper-Stabilized Hall Effect Bipolar Switch Electrical Characteristic Data Supply Current (On) versus Ambient Temperature Supply Current (On) versus Supply Voltage 5.0 5.0 4.0 VCC (V) 3.0 24 3.6 2.0 ICCON (mA) ICCON (mA) 4.0 1.0 3.0 –40 25 150 2.0 1.0 0 –50 TA (°C) 0 0 50 TA (°C) 100 150 0 25 4.0 VCC (V) 3.0 24 3.6 2.0 ICCOFF (mA) ICCOFF (mA) 20 5.0 4.0 TA (°C) –40 25 150 3.0 2.0 1.0 1.0 0 0 0 50 TA (°C) 100 0 150 5 10 15 20 25 VCC (V) Output Voltage (On) versus Ambient Temperature Output Voltage (On) versus Supply Voltage 500 500 450 450 400 400 350 350 300 VCC (V) 250 24 3.6 200 150 VOUT(SAT) (mV) VOUT(SAT) (mV) 15 Supply Current (Off) versus Supply Voltage 5.0 TA (°C) 300 –40 25 150 250 200 150 100 100 50 50 0 –50 10 VCC (V) Supply Current (Off) versus Ambient Temperature –50 5 0 0 50 TA (°C) 100 150 0 5 10 15 20 25 VCC (V) Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 4 A3230 Chopper-Stabilized Hall Effect Bipolar Switch Magnetic Characteristic Data Operate Point versus Ambient Temperature Operate Point versus Supply Voltage 25 25 20 20 15 10 VCC (V) 5 24 3.8 TA (°C) 10 BOP (G) BOP (G) 15 –40 25 150 5 0 0 -5 -5 -10 -10 –50 0 50 TA (°C) 100 150 0 15 20 25 Release Point versus Supply Voltage 10 10 5 5 0 -5 VCC (V) -10 24 3.8 BRP (G) 0 BRP (G) 10 VCC (V) Release Point versus Ambient Temperature TA (°C) -5 –40 25 150 -10 -15 -15 -20 -20 -25 -25 –50 0 50 TA (°C) 100 0 150 5 10 15 20 25 VCC (V) Hysteresis versus Ambient Temperature Hysteresis versus Supply Voltage 25 25 20 20 VCC (V) 24 3.8 15 10 BHYS (G) BHYS (G) 5 TA (°C) –40 25 150 15 10 5 5 –50 0 50 TA (°C) 100 150 0 5 10 15 20 25 VCC (V) Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 5 A3230 Chopper-Stabilized Hall Effect Bipolar Switch THERMAL CHARACTERISTICS may require derating at maximum conditions, see application information Characteristic Symbol Test Conditions* RθJA Package Thermal Resistance Value Units Package LH, 1-layer PCB with copper limited to solder pads 228 ºC/W Package LH, 2-layer PCB with 0.463 in.2 of copper area each side connected by thermal vias 110 ºC/W Package UA, 1-layer PCB with copper limited to solder pads 165 ºC/W *Additional thermal information available on Allegro Web site. Maximum Allowable VCC (V) Power Derating Curve 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 VCC(max) 2-layer PCB, Package LH (RθJA = 110 ºC/W) 1-layer PCB, Package UA (RθJA = 165 ºC/W) 1-layer PCB, Package LH (RθJA = 228 ºC/W) VCC(min) 20 40 60 80 100 120 140 160 180 Temperature (ºC) Power Dissipation, PD (m W) Power Dissipation versus Ambient Temperature 1900 1800 1700 1600 1500 1400 1300 1200 1100 1000 900 800 700 600 500 400 300 200 100 0 2l (R aye rP θJ C A = 11 B, P 0 º ac 1-la C/ ka W (R yer PC ) ge L θJA = B H 165 , Pac ºC/ kage W) UA 1-lay er P (R CB, θJA = 228 Packag ºC/W e LH ) 20 40 60 80 100 120 Temperature (°C) 140 160 180 Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 6 A3230 Chopper-Stabilized Hall Effect Bipolar Switch Functional Description Operation The output of these devices switches low (turns on) when a magnetic field perpendicular to the Hall element exceeds the operate point threshold, BOP. After turn-on, the output voltage is VOUT(SAT). The output transistor is capable of sinking current up to the short circuit current limit, IOM, which is a minimum of 30 mA. When the magnetic field is reduced below the release point, BRP, the device output goes high (turns off). The difference in the magnetic operate and release points is the hysteresis, BHYS, of the device. This built-in hysteresis allows clean switching of the output even in the presence of external mechanical vibration and electrical noise. field of the opposite polarity and of sufficient strength causes it to switch. The hysteresis of latch mode behavior is shown in panel A of figure 1. In contrast to latching, when a device exhibits unipolar switching, it only responds to a south magnetic field. The field must be of sufficient strength, > BOP , for the device to operate. When the field is reduced beyond the BRP level, the device switches back to the high state, as shown in panel B of figure 1. Devices VS There are three switching modes for bipolar devices, referred to as latch, unipolar switch, and negative switch. Mode is determined by the switchpoint characteristics of the individual device. Note that, as shown in figure 1, these switchpoints can lie in either north or south polarity ranges. The values of the magnetic parameters for the A3230 are specified in the Magnetic Characteristics table, on page 3. VCC CBYP 0.1 µF A3230 RLOAD Output VOUT GND Bipolar devices typically behave as latches (although these devices are not guaranteed to do so). In this mode, magnetic fields of opposite polarity and equivalent strengths are needed to switch the output. When the magnetic fields are removed (B 0) the device remains in the same state until a magnetic (D) (A) (B) V+ V+ Switch to High Switch to High VOUT BHYS B+ B– BRP(MIN) BRP B– 0 VOUT(SAT) 0 BOP BHYS B+ VOUT(SAT) 0 BOP(MAX) 0 BOP B– BRP VOUT(SAT) 0 VCC Switch to Low VOUT VCC Switch to Low Switch to Low Switch to High VCC VOUT V+ (C) 0 B+ BHYS Figure 1. Bipolar Device Output Switching Modes. These behaviors can be exhibited when using a circuit such as that shown in panel D. Panel A displays the hysteresis when a device exhibits latch mode (note that the BHYS band incorporates B= 0), panel B shows unipolar switch behavior (the BHYS band is more positive than B = 0), and panel C shows negative switch behavior (the BHYS band is more negative than B = 0). Bipolar devices, such as the A3230, can operate in any of the three modes. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 7 A3230 Chopper-Stabilized Hall Effect Bipolar Switch exhibiting negative switch behavior operate in a similar but opposite manner. A north polarity field of sufficient strength, > BRP , (more north than BRP) is required for operation, although the result is that VOUT switches high, as shown in panel C. When the field is reduced beyond the BOP level, the device switches back to the low state. Applications It is strongly recommended that an external bypass capacitor be connected (in close proximity to the Hall element) between the supply and ground of the device to reduce both external noise and noise generated by the chopper stabilization technique. As is shown in Panel B of figure 1, a 0.1μF capacitor is typical. The A3230 is designed to attain a small hysteresis, and thereby provide more sensitive switching. Although this means that true latching behavior cannot be guaranteed in all cases, proper switching can be ensured by use of both south and north magnetic fields, as in a ring magnet. Extensive applications information on magnets and Hall-effect devices is available in: Bipolar devices adopt an indeterminate output state when powered-on in the absence of a magnetic field or in a field that lies within the hysteresis band of the device. The correct state is attained after the first excursion beyond BOP or BRP. For more information on Bipolar switches, refer to Application Note 27705, Understanding Bipolar Hall Effect Sensor ICs. • Hall-Effect IC Applications Guide, AN27701, • Hall-Effect Devices: Gluing, Potting, Encapsulating, Lead Welding and Lead Forming, AN27703.1 • Soldering Methods for Allegro’s Products – SMT and ThroughHole, AN26009 All are provided in Allegro Electronic Data Book, AMS-702 and the Allegro Web site: www.allegromicro.com Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 8 A3230 Chopper-Stabilized Hall Effect Bipolar Switch Chopper Stabilization Technique When using Hall-effect technology, a limiting factor for switchpoint accuracy is the small signal voltage developed across the Hall element. This voltage is disproportionally small relative to the offset that can be produced at the output of the Hall element. This makes it difficult to process the signal while maintaining an accurate, reliable output over the specified operating temperature and voltage ranges. Chopper stabilization is a unique approach used to minimize Hall offset on the chip. The patented Allegro technique, namely Dynamic Quadrature Offset Cancellation, removes key sources of the output drift induced by thermal and mechanical stresses. This offset reduction technique is based on a signal modulationdemodulation process. The undesired offset signal is separated from the magnetic-field-induced signal in the frequency domain, through modulation. The subsequent demodulation acts as a modulation process for the offset, causing the magnetic-fieldinduced signal to recover its original spectrum at baseband, while the dc offset becomes a high-frequency signal. The magnetic-field-induced signal then can pass through a low-pass filter, while the modulated dc offset is suppressed. This configuration is illustrated in figure 2. The chopper stabilization technique uses a 200 kHz high-frequency clock. For demodulation process, a sample and hold technique is used, where the sampling is performed at twice the chopper frequency (400 kHz). This high-frequency operation allows a greater sampling rate, which results in higher accuracy and faster signal-processing capability. This approach desensitizes the chip to the effects of thermal and mechanical stresses, and produces devices that have extremely stable quiescent Hall output voltages and precise recoverability after temperature cycling. This technique is made possible through the use of a BiCMOS process, which allows the use of low-offset, low-noise amplifiers in combination with high-density logic integration and sample-and-hold circuits. The repeatability of magnetic-field-induced switching is affected slightly by a chopper technique. However, the Allegro highfrequency chopping approach minimizes the affect of jitter and makes it imperceptible in most applications. Applications that are more likely to be sensitive to such degradation are those requiring precise sensing of alternating magnetic fields; for example, speed sensing of ring-magnet targets. For such applications, Allegro recommends its digital device families with lower sensitivity to jitter. For more information on those devices, contact your Allegro sales representative. Regulator Amp Low-Pass Filter Hall Element Sample and Hold Clock/Logic Figure 2. Chopper Stabilization Circuit (Dynamic Quadrature Offset Cancellation) Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 9 A3230 Chopper-Stabilized Hall Effect Bipolar Switch Power Derating The device must be operated below the maximum junction temperature of the device, TJ(max). Under certain combinations of peak conditions, reliable operation may require derating supplied power or improving the heat dissipation properties of the application. This section presents a procedure for correlating factors affecting operating TJ. (Thermal data is also available on the Allegro MicroSystems Web site.) The Package Thermal Resistance, RJA, is a figure of merit summarizing the ability of the application and the device to dissipate heat from the junction (die), through all paths to the ambient air. Its primary component is the Effective Thermal Conductivity, K, of the printed circuit board, including adjacent devices and traces. Radiation from the die through the device case, RJC, is relatively small component of RJA. Ambient air temperature, TA, and air motion are significant external factors, damped by overmolding. The effect of varying power levels (Power Dissipation, PD), can be estimated. The following formulas represent the fundamental relationships used to estimate TJ, at PD. PD = VIN × IIN (1) Example: Reliability for VCC at TA = 150°C, package LH, using a low-K PCB. Observe the worst-case ratings for the device, specifically: RJA = 228 °C/W, TJ(max) = 165°C, VCC(max) = 24 V, and ICC(max) = 5 mA. Calculate the maximum allowable power level, PD(max). First, invert equation 3: Tmax = TJ(max) – TA = 165 °C – 150 °C = 15 °C This provides the allowable increase to TJ resulting from internal power dissipation. Then, invert equation 2: PD(max) = Tmax ÷ RJA = 15°C ÷ 228 °C/W = 66 mW Finally, invert equation 1 with respect to voltage: VCC(est) = PD(max) ÷ ICC(max) = 66 mW ÷ 5 mA = 13 V The result indicates that, at TA, the application and device can dissipate adequate amounts of heat at voltages ≤VCC(est). Compare VCC(est) to VCC(max). If VCC(est) ≤ VCC(max), then reliable operation between VCC(est) and VCC(max) requires enhanced RJA. If VCC(est) ≥ VCC(max), then operation between VCC(est) and VCC(max) is reliable under these conditions. T = PD × RJA (2) TJ = TA + ΔT (3) For example, given common conditions such as: TA= 25°C, VCC = 12 V, ICC = 1.5 mA, and RJA = 165 °C/W, then: PD = VCC × ICC = 12 V × 1.5 mA = 18 mW T = PD × RJA = 18 mW × 165 °C/W = 3°C TJ = TA + T = 25°C + 3°C = 28°C A worst-case estimate, PD(max), represents the maximum allowable power level (VCC(max), ICC(max)), without exceeding TJ(max), at a selected RJA and TA. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 10 A3230 Chopper-Stabilized Hall Effect Bipolar Switch Package LH, 3-Pin SOT23-W +0.12 2.98 –0.08 1.49 D 4°±4° 3 A +0.020 0.180–0.053 0.96 D +0.10 2.90 –0.20 +0.19 1.91 –0.06 2.40 0.70 D 0.25 MIN 1.00 2 1 0.55 REF 0.25 BSC 0.95 Seating Plane Gauge Plane PCB Layout Reference View B Branded Face 8X 10° REF 1.00 ±0.13 NNT +0.10 0.05 –0.05 0.95 BSC 1 C 0.40 ±0.10 N = Last two digits of device part number T = Temperature code For Reference Only; not for tooling use (reference dwg. 802840) Dimensions in millimeters Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration at supplier discretion within limits shown A Active Area Depth, 0.28 mm REF B Reference land pattern layout All pads a minimum of 0.20 mm from all adjacent pads; adjust as necessary to meet application process requirements and PCB layout tolerances C Branding scale and appearance at supplier discretion D Hall element, not to scale Standard Branding Reference View Pin-out Drawings Package UA Package LH 3 1 1 2 2 3 Terminal List Name Description Number Package LH Package UA Connects power supply to chip 1 1 VOUT Output from circuit 2 3 GND Ground 3 2 VCC Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 11 A3230 Chopper-Stabilized Hall Effect Bipolar Switch Package UA, 3-Pin SIP +0.08 4.09 –0.05 45° B C E 2.04 1.52 ±0.05 1.44 E Mold Ejector Pin Indent +0.08 3.02 –0.05 E Branded Face 45° 1 2.16 MAX D Standard Branding Reference View = Supplier emblem N = Last two digits of device part number T = Temperature code 0.79 REF A 0.51 REF NNT 1 2 3 +0.03 0.41 –0.06 15.75 ±0.51 For Reference Only; not for tooling use (reference DWG-9049) Dimensions in millimeters Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration at supplier discretion within limits shown A Dambar removal protrusion (6X) B Gate burr area C Active Area Depth, 0.50 mm REF +0.05 0.43 –0.07 D Branding scale and appearance at supplier discretion E Hall element, not to scale 1.27 NOM Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 12 A3230 Chopper-Stabilized Hall Effect Bipolar Switch Revision History Revision Revision Date Rev. 9 April 30, 2012 Description of Revision Update product availability Copyright ©2005-2013, Allegro MicroSystems, LLC Allegro MicroSystems, LLC reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro’s products are not to be used in any devices or systems, including but not limited to life support devices or systems, in which a failure of Allegro’s product can reasonably be expected to cause bodily harm. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. For the latest version of this document, visit our website: www.allegromicro.com Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 13