Download

IL600 Series Isolators
Passive-Input Digital Isolators – CMOS Outputs
Functional Diagrams
Features
VOE
OUT1
IN1
IL610
IN1
OUT1
IN2
OUT2
IL611
OUT1
VDD2
OUT2
Up to 100 Mbps data rate
Flexible inputs with very wide input voltage range
5 mA input current
Failsafe output (logic high output for zero coil current)
No carrier or clock for low EMI emissions and susceptibility
Low power dissipation
3 V to 5 V power supplies
1000 VRMS/1500 VDC high voltage endurance
44000 year barrier life
−40°C to 85°C temperature range
UL 1577 recognized; IEC 60747-5-5 (VDE 0884) certified
8-pin MSOP, SOIC, and PDIP packages
0.15", 0.3", or True 8™ mm SOIC packages
Applications
VDD1
IN1
•
•
•
•
•
•
•
•
•
•
•
•
•
IN2
IL612
•
•
•
•
•
•
•
CAN Bus / Device Net
Differential line receiver
Optocoupler replacement
SPI interface
RS-485, RS-422, or RS-232
Digital Fieldbus
Space-critical multi-channel applications
Description
IN1
OUT1
IN2
OUT2
IN3
OUT3
IL613
OUT1
VOE
OUT2
COIL
The devices are manufactured with NVE’s patented*
IsoLoop® spintronic Giant Magnetoresistive (GMR)
technology for small size, high speed, and low power.
A unique ceramic/polymer composite barrier provides
excellent isolation and virtually unlimited barrier life.
IN1
IN2
The IL600 Series are passive input digital signal isolators
with CMOS outputs. They have a similar interface but better
performance and higher package density than optocouplers.
OUT3
IN3
IL614
A resistor sets the input current; a capacitor in parallel with
the current-limit resistor provides improved dynamic
performance.
These versatile components simplify inventory requirements
by replacing a variety of optocouplers, functioning over a
wide range of data rates, edge speeds, and power supply
levels. The devices are available in various packages, as well
as bare die.
IsoLoop is a registered trademark of NVE Corporation.
*U.S. Patent number 5,831,426; 6,300,617 and others.
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
REV. AA
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL600 Series Isolators
Absolute Maximum Ratings(1)
Parameters
Storage Temperature
Ambient Operating Temperature
Supply Voltage
DC Input Current
AC Input Current (Single-Ended
Input)
AC Input Current (Differential Input)
Output Voltage
Maximum Output Current
ESD
Symbol
TS
TA
VDD
IIN
Min.
−55
−40
−0.5
−25
IIN
IIN
VO
IO
Typ.
Max.
150
85
7
25
Units
°C
°C
V
mA
−35
35
mA
−75
−0.5
−10
75
VDD+1.5
10
mA
V
mA
kV
2
Test Conditions
HBM
Note 1: Operating at absolute maximum ratings will not damage the device. Parametric performance is not guaranteed at absolute maximum ratings.
Recommended Operating Conditions
Parameters
Ambient Operating Temperature
Supply Voltage
Output Current
Common Mode Input Voltage
Symbol
TA
VDD
IOUT
VCM
Min.
−40
3.0
−4
Typ.
Max.
85
5.5
4
400
Units
°C
V
mA
VRMS
Test Conditions
Symbol
Min.
Typ.
Max.
Units
Test Conditions
Insulation Specifications
Parameters
Creepage Distance (external)
MSOP
0.15'' SOIC
0.3'' SOIC
PDIP
Total Barrier Thickness (internal)
Leakage Current
Barrier Resistance
Barrier Capacitance
Comparative Tracking Index
High Voltage Endurance
AC
(Maximum Barrier Voltage
for Indefinite Life)
DC
3.01
4.03
8.03
7.08
0.012
RIO
CIO
CTI
mm
mm
mm
mm
mm
μA
8.3
0.013
0.2
>1014
7
≥175
1000
Ω || pF
V
VRMS
1500
VDC
V
IO
Barrier Life
44000
Years
Per IEC 60601
240 VRMS, 60 Hz
500 V
f = 1 MHz
Per IEC 60112
At maximum
operating temperature
100°C, 1000 VRMS, 60%
CL activation energy
2
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL600 Series Isolators
Safety and Approvals
IEC 60747-5-5 (VDE 0884) (File Number 5016933-4880-0001)
• Working Voltage (VIORM) 600 VRMS (848 VPK); basic insulation; pollution degree 2
• Transient overvoltage (VIOTM) and surge voltage (VIOSM) 4000 VPK
• Each part tested at 1590 VPK for 1 second, 5 pC partial discharge limit
• Samples tested at 4000 VPK for 60 sec.; then 1358 VPK for 10 sec. with 5 pC partial discharge limit
IEC 61010-1 (Edition 2; TUV Certificate Numbers N1502812; N1502812-101)
Reinforced Insulation; Pollution Degree II; Material Group III
Part No. Suffix
-1
-2
-3
None
Package
MSOP
PDIP
SOIC
Wide-body SOIC/True 8™
Working Voltage
150 VRMS
300 VRMS
150 VRMS
300 VRMS
UL 1577 (Component Recognition Program File Number E207481)
Each part other than MSOP tested at 3000 VRMS (4240 VPK) for 1 second; each lot sample tested at 2500 VRMS (3530 VPK) for 1 minute
MSOP tested at 1200 VRMS (1768 VPK) for 1 second; each lot sample tested at 1500 VRMS (2121 VPK) for 1 minute
Soldering Profile
Per JEDEC J-STD-020C; MSL 1
Electrostatic Discharge Sensitivity
This product has been tested for electrostatic sensitivity to the limits stated in the specifications. However, NVE recommends that all integrated
circuits be handled with appropriate care to avoid damage. Damage caused by inappropriate handling or storage could range from performance
degradation to complete failure.
3
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL600 Series Isolators
IL610 Pin Connections
1
2
3
4
5
6
NC
IN+
IN−
NC
GND
OUT
7
VOE
8
VDD
No internal connection
Coil connection
Coil connection
No internal connection
Ground return for VDD
Data out
Output enable.
Internally held low with 100 kΩ
Supply Voltage
NC
VDD
IN+
VOE
IN-
OUT
NC
GND
IL610
IL611 Pin Connections
1
2
3
4
5
6
7
8
IN1+
IN1−
IN2+
IN2−
GND
OUT2
OUT1
VDD
Channel 1 coil connection
Channel 1 coil connection
Channel 2 coil connection
Channel 2 coil connection
Ground return for VDD
Data out, channel 2
Data out, channel 1
Supply Voltage
IN1+
VDD
IN1-
OUT1
IN2+
OUT2
IN2-
GND
IL611
IL612 Pin Connections
1
2
3
4
5
6
7
8
IN1
VDD1
OUT2
GND1
GND2
IN2
VDD2
OUT1
Data in, channel 1
Supply Voltage 1
Data out, channel 2
Ground return for VDD1
Ground return for VDD2
Data in, channel 2
Supply Voltage 2
Data out, channel 1
IN1
OUT1
VDD1
VDD2
OUT2
IN2
GND1
GND2
IL612
IL613 Pin Connections
1
IN1+
2
NC
3
4
5
6
7
IN1−
IN2+
IN2−
IN3+
IN3−
8
NC
9
GND
10
11
OUT3
NC
12
VDD
13
14
OUT2
OUT1
15
GND
16
VDD
Channel 1 coil connection
No connection
(internally connected to pin 8)
Channel 1 coil connection
Channel 2 coil connection
Channel 2 coil connection
Channel 3 coil connection
Channel 3 coil connection
No connection
(internally connected to pin 2)
Ground return for VDD
(internally connected to pin 15)
Data out, channel 3
No connection
Supply Voltage. Pin 12 and pin 16
must be connected externally
Data out, channel 2
Data out, channel 1
Ground return for VDD
(internally connected to pin 9)
Supply Voltage. Pin 12 and pin 16
must be connected externally
IN1+
VDD
NC
GND*
IN1-
OUT1
IN2+
OUT2
IN2-
VDD
IN3+
NC
IN3-
OUT3
NC
GND
IL613
Note: Pins 12 and 16 must be connected externally.
4
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL600 Series Isolators
IL614 Pin Connections
1
VDD1
2
GND1
3
OUT1
4
VOE
5
IN2
6
Vcoil
7
IN3
8
GND1
9
GND2
10
11
12
13
14
NC
OUT3
VDD2
OUT2
IN1+
15
GND2
16
IN1−
Supply Voltage 1
Ground return for VDD1
(internally connected to pin 8)
Data out, channel 1
Channel 1 data output enable.
Internally held low with 100 kΩ
Data in, channel 2
Supply connection for
channel 2 and channel 3 coils
Data in, channel 3
Ground return for VDD1
(internally connected to pin 2)
Ground return for VDD2
(internally connected to pin 15)
No Connection
Data out, channel 3
Supply Voltage 2
Data out, channel 2
Coil connection
Ground return for VDD2
(internally connected to pin 9)
Coil connection
VDD1
IN1-
GND1
GND2
OUT1
IN1+
VOE
OUT2
IN2
VDD2
VCOIL
OUT3
IN3
NC
GND2
GND1
IL614
5
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL600 Series Isolators
Operating Specifications
Input Specifications (VDD = 3 V − 5.5 V; T = −40°C − 85°C unless otherwise stated)
Symbol
Min.
Typ.
Max.
Units
47
85
112
Ω
Coil Input Resistance
RCOIL
31
85
128
Ω
Coil Resistance Temperature Coefficient
TC RCOIL
0.2
0.25
Ω/°C
Coil Inductance
LCOIL
9
nH
IINH-DC
0.5
1
mA
DC Input Threshold (5 V)
IINL-DC
3.5
5
mA
0.3
0.5
mA
IINH-DC
DC Input Threshold (3 V)
IINL-DC
5
8
mA
Parameters
IINH-BOOST
Dynamic Input Threshold (3 V)
0.5
1
IINL-BOOST
IINH-DIFF
Differential Input Threshold
3.5
0.5
IFS-HIGH
IFS-LOW
IFS-HIGH
IFS-LOW
tIR, tIF
|CMH|,|CML|
Failsafe Input Current(1) (3 V)
Input Signal Rise and Fall Times
Common Mode Transient Immunity
5
1
IINL-DIFF
Failsafe Input Current(1) (5 V)
mA
mA
3.5
−25
5
−25
8
15
mA
5
mA
0.5
25
0.3
25
1
mA
mA
mA
mA
μs
kV/μs
20
Test Conditions
T = 25°C
T = −40°C − 85°C
Test Circuit 1;
VDD = 4.5 V − 5.5 V
Test Circuit 1;
VDD = 3V − 3.6 V;
no boost cap
VDD = 3V − 3.6 V;
tIR = tIF = 3 ns;
CBOOST = 16 pF
Test Circuit 2;
VDD = 3V − 5.5 V;
input current reverses;
boost cap not required
Test Circuit 1;
VDD = 4.5 V − 5.5 V
Test Circuit 1;
VDD = 3 V − 3.6 V
VT = 300 Vpeak
Notes:
1. Failsafe Operation is defined as the guaranteed output state which will be achieved if the DC input current falls between the input levels specified
(see Test Circuit 1 for details). Note if Failsafe to Logic Low is required, the DC current supplied to the coil must be at least 8 mA using 3.3 V supplies
versus 5 mA for 5 V supplies.
+V
Rlimit
Cboost
VDD
+V
VDD
10 nF
IL610
3
2 +
10 nF
8
8
IL610
Rlimit
7
7
3
6
2 +
5
6
5
15 pF
15 pF
1K
GND1
1K
GND2
GND1
Test Circuit 1 (Single-Ended)
GND2
Test Circuit 2 (Differential)
6
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL600 Series Isolators
5 V Electrical Specifications (VDD = 4.5 V − 5.5 V; T = −40°C − 85°C unless otherwise stated)
Parameters
Symbol
Min.
Typ.
Max.
Units
Test Conditions
Quiescent Supply Current
IL610
IDD
2
3
IL611
IDD
4
6
IL612
IDD1
2
3
mA
VDD = 5 V, IIN = 0
IL612
IDD2
2
3
IL613
IDD
6
9
IL614
IDD1
2
3
IL614
IDD2
4
6
4.9
5
V
VDD = 5 V, IO = 20 μA
Logic High Output Voltage
VOH
4.0
4.8
V
VDD = 5 V, IO = 4 mA
0
0.1
V
VDD = 5 V, IO = −20 μA
Logic Low Output Voltage
VOL
0.2
0.8
V
VDD = 5 V, IO = −4 mA
Logic Output Drive Current
|IO|
7
10
mA
5 V Switching Specifications (VDD = 4.5 V − 5.5 V; T = −40°C − 85°C unless otherwise stated)
Parameters
Symbol
Min.
Typ.
Max.
Units
Test Conditions
Data Rate
100
Mbps
Minimum Pulse Width(1)
PW
10
ns
Propagation Delay Input to Output
8
15
ns
tPHL
(High-to-Low)
Propagation Delay Input to Output
8
15
ns
tPLH
Test Circuit 1;
(Low to High)
tIR = tIF = 3 ns;
Average Propagation Delay Drift
tPLH
10
ps/°C
CBOOST = 16 pF
(2)
Pulse Width Distortion |tPHL−tPLH|
PWD
3
5
ns
Pulse Jitter(3)
tJ
100
ps
Propagation Delay Skew(4)
tPSK
−2
2
ns
Output Rise Time (10–90%)
tR
2
4
ns
Output Fall Time (10–90%)
tF
2
4
ns
Notes:
1.
2.
3.
4.
Minimum Pulse Width is the shortest pulse width at which the specified PWD is guaranteed.
PWD is defined as | tPHL − tPLH |.
66,535-bit pseudo-random binary signal (PRBS) NRZ bit pattern with no more than five consecutive 1s or 0s; 800 ps transition time.
tPSK is equal to the magnitude of the worst case difference in tPHL and/or tPLH that will be seen between units at 25°C.
7
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL600 Series Isolators
3.3 V Electrical Specifications (VDD = 3 V − 3.6 V; T = −40°C − 85°C unless otherwise stated)
Parameters
Symbol
Min.
Typ.
Max.
Units
Test Conditions
Quiescent Supply Current
IL610
IDD
1.3
2
IL611
IDD
2.6
4
IL612
IDD1
1.3
2
mA
VDD = 3.3 V, IIN = 0
IL612
IDD2
1.3
2
IL613
IDD
4
6
IL614
IDD1
1.3
2
IL614
IDD2
2.6
4
3.2
3.3
V
VDD = 3.3 V, IO = 20 μA
Logic High Output Voltage
VOH
3.0
3.1
V
VDD = 3.3 V, IO = 4 mA
0
0.1
V
VDD = 3.3 V, IO = −20 μA
Logic Low Output Voltage
VOL
0.2
0.8
V
VDD = 3.3 V, IO = −4 mA
Logic Output Drive Current
|IO|
7
10
mA
3.3 V Switching Specifications (VDD = 3 V − 3.6 V; T = −40°C − 85°C unless otherwise stated)
Data Rate
100
Mbps
Minimum Pulse Width(1)
PW
10
ns
Propagation Delay Input to Output
tPHL
12
18
ns
(High to Low)
Propagation Delay Input to Output
Test Circuit 1;
tPLH
12
18
ns
(Low to High)
tIR = tIF = 3 ns;
CBOOST = 16 pF
Average Propagation Delay Drift
tPLH
10
ps/°C
Pulse Width Distortion |tPHL−tPLH| (2)
PWD
3
5
ns
Propagation Delay Skew(3)
tPSK
−2
2
ns
Output Rise Time (10–90%)
tR
3
5
ns
Output Fall Time (10–90%)
tF
3
5
ns
Notes:
1. The Minimum Pulse Width is the shortest pulse width at which the specified PWD is guaranteed.
2. PWD is defined as | tPHL − tPLH |.
3. tPSK is equal to the magnitude of the worst case difference in tPHL and/or tPLH that will be seen between units at 25°C.
8
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL600 Series Isolators
Applications Information
IL600-Series Isolators are current mode devices. Changes in current flow into the input coil result in logic state changes at the
output. As shown in Figure 1, output logic high is the zero input current state.
Coil Polarity
3.5
The device switches to logic low if current flows from (In−) to (In+).
Note that the designations “In−“ and “In+” refer to logic levels, not
current flow. Positive values of current mean current flow into
the In− input.
1.5
Input Resistor Selection
Coil Current
mA
5
t
Logic State
High
Low
t
Figure 1. Typical IL600-Series Transfer Function
Resistors set the coil input current (see Figure 2). There is no limit to
input voltages because there are no semiconductor input structures.
Worst-case logic low threshold current is 8 mA, which is for singleended operation with a 3 V supply. In differential mode, where the
input current reverses, the logic low threshold current is 5 mA for the
range of supplies. A “boost capacitor” creates current reversals at edge
transitions, reducing the input logic low threshold current to the
differential level of 5 mA.
Typical Resistor Values
The table shows typical
values for the external
resistor for 5 mA coil
current. The values are
approximate and should be adjusted for temperature or other
application specifics. If the expected temperature range is large, 1%
tolerance resistors may provide additional design margin.
VCOIL
3.3 V
5V
ICOIL
VINH
R1
85
Input
Coil
0.125W, 5% Resistor
510 Ω
820 Ω
Single-Ended or Differential Input
The IL610, IL611, IL613, and channel 1 of the IL614 can be run with
single-ended or differential inputs (see Test Circuits on page 5). In the
differential mode, current will naturally flow through the coil in both
directions without a boost capacitor, although the capacitor can still be
used for increased external field immunity or improved PWD.
VINL
Figure 2. Limiting Resistor Calculation
Equivalent Circuit
Absolute Maximum recommended coil current in single-ended mode
is 25 mA while differential mode allows up to ±75 mA to flow. The
difference in specifications is due to the risk of electromigration of
coil metals under constant current flow. In single ended mode, long-term DC current flow above 25 mA can cause erosion of the
coil metal. In differential mode, erosion takes place in both directions as each current cycle reverses and has a net effect of zero up
to the absolute maximum current.
An advantage over optocouplers and other high-speed couplers in differential mode is that no reverse bias protection for the input
structure is required for a differential signal.
One of the more common applications is for an isolated Differential Line Receiver. For example, RS-485 can drive an IL610
directly for a fraction of the cost of an isolated RS-485 node (see Illustrative Applications).
9
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL600 Series Isolators
Non-inverting and Inverting Configurations
IL600-Series Isolators can be configured in noninverting and inverting configurations (see Figure 3).
In a typical non-inverting circuit, the In− terminal is
connected via a 1 kΩ input resistor to the supply rail,
and the input is connected to the In+ terminal. The
supply voltage is +5 V and the input signal is a 5 V
CMOS signal. When a logic high (+5 V) is applied to
the input, the current through the coil is zero. When
the input is a logic low (0 V), at least 5 mA flows
through the coil from the In− side to the In+ side.
The inverting configuration is similar to standard
logic. In the inverting configuration, the signal into
the coil is differential with respect to ground. The
designer must ensure that the difference between the
logic low voltage and the coil ground is such that the
residual coil current is less than 0.5 mA.
+5 V
Cboost
820R
IL610
3
2 +
VDD
8
7
6
C1
Data Out
5
Data In
GND1
GND2
Note: C1 is 47 nF ceramic.
Non-Inverting Circuit
+5 V
The IL612 and IL614 devices have some inputs that
do not offer inverting operation. The IL612 coil In−
input is hardwired internally to the device power
supply; therefore it is important to ensure the isolator
power supply is at the same voltage as the power
supply to the source of the input logic signal. The
IL614 has a common coil In− for two inputs. This
pin should be connected to the power supply for the
logic driving channels 2 and 3, and the channels run
should be run in non-inverting mode.
VDD
IL610
Cboost
3
Data In
820R
2 +
8
7
6
C1
Data Out
5
Both single ended and differential inputs can be
handled without reverse bias protection.
GND1
Inverting Circuit
GND2
Note: C1 is 47 nF ceramic.
Figure 3. Non-inverting and inverting circuits
Boost Capacitor
The boost capacitor in parallel with the current-limiting resistor boosts the instantaneous coil current at the signal transition. This
ensures switching and reduces propagation delay and reduces pulse-width distortion.
Select the value of the boost capacitor based on the rise and fall
times of the signal driving the inputs. The instantaneous boost
dV
capacitor current is proportional to input edge speeds ( C dt ). Select a
capacitor value based on the rise and fall times of the input signal to be
isolated that provides approximately 20 mA of additional “boost”
current. Figure 4 is a guide to boost capacitor selection. For high-speed
logic signals (tr,tf < 10 ns), a 16 pF capacitor is recommended. The
capacitor value is generally not critical; if in doubt, choose a higher
value.
1000
Signal
Rise/Fall Time (ns)
500
3
16
2500
5000
CBoost (pF)
Figure 4. Cboost Selector
10
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL600 Series Isolators
Dynamic Power Consumption
Power consumption is proportional to duty cycle, not data rate. The use of NRZ coding minimizes power dissipation since no
additional power is consumed when the output is in the high state. In differential mode, where the logic high condition may still
require a current to be forced through the coil, power consumption will be higher than a typical NRZ single ended configuration.
Power Supply Decoupling
47 nF low-ESR ceramic capacitors are recommended to decouple the power supplies. The capacitors should be placed as close as
possible to the appropriate VDD pin.
Maintaining Creepage
Creepage distances are often critical in isolated circuits. In addition to meeting JEDEC standards, NVE isolator packages have
unique creepage specifications. Standard pad libraries often extend under the package, compromising creepage and clearance.
Similarly, ground planes, if used, should be spaced to avoid compromising clearance. Package drawings and recommended pad
layouts are included in this datasheet.
Electromagnetic Compatibility and Magnetic Field Immunity
Because IL600-Series Isolators are completely static, they have the lowest emitted noise of any non-optical isolators.
IsoLoop Isolators operate by imposing a magnetic field on a GMR sensor, which translates the change in field into a change in
logic state. A magnetic shield and a Wheatstone Bridge configuration provide good immunity to external magnetic fields.
Immunity to external magnetic fields can be enhanced by proper orientation of the device with respect to the field direction, the
use of differential signaling, and boost capacitors.
1. Orientation of the device with respect to the field direction
An applied field in the “H1” direction is the worst case for
magnetic immunity. In this case the external field is in the same
direction as the applied internal field. In one direction it will
tend to help switching; in the other it will hinder switching.
This can cause unpredictable operation.
NC
VDD
IN+
IN-
An applied field in direction “H2” has considerably less effect
and results in higher magnetic immunity.
VOE
H2
H1
OUT
GND
NC
2. Differential Signaling and Boost Capacitors
Regardless of orientation, driving the coil differentially improves magnetic immunity. This is because the logic high state is driven
by an applied field instead of zero field, as is the case with single-ended operation. The higher the coil current, the higher the
internal field, and the higher the immunity to external fields. Optimal magnetic immunity is achieved by adding the boost
capacitor.
Method
Approximate Immunity
Immunity Description
A DC current of 16 A flowing in a conductor
1 cm from the device could cause disturbance.
Field applied in H1 direction
±20 Gauss
Field applied in H2 direction
±70 Gauss
A DC current of 56 A flowing in a conductor
1 cm from the device could cause disturbance.
Field applied in any direction but with boost
capacitor (16 pF) in circuit
±250 Gauss
A DC current of 200 A flowing in a conductor
1 cm from the device could cause disturbance.
Data Rate and Magnetic Field Immunity
It is easier to disrupt an isolated DC signal with an external magnetic field than it is to disrupt an isolated AC signal. Similarly, a
DC magnetic field will have a greater effect on the device than an AC magnetic field of the same effective magnitude. For
example, signals with pulses longer than 100 μs are more susceptible to magnetic fields than shorter pulse widths.
11
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL600 Series Isolators
Illustrative Applications
V DD1
V DD
8
R
V DD2
V DD1
1
ISL8485
IL610
ISL8490
2
3
1
+
-
8
RE
7
6
47nF
R
5
47nF
47nF
8
IL610
B
7
D
3
4
2
6
+
GND2
RE
7
6
47nF
6
R
D
Z
3
5
Y
5
IL610
17R
3
A
5
V DD3
17R
4
2
+
8
RE
7
47nF
6
R
5
GND1
GND2
GND3
GND1
Isolated RS-485 and RS-422 Receivers Using IL610s
IL610s can be used as simple isolated RS-485 or RS-422 receivers, terminating signals at
the IL610 for a fraction of the cost of an isolated node. Cabling is simplified by eliminating
the need to power the input side of the receiving board. No current-limiting resistor is
needed for a single receiver because it will draw less current than the driver maximum.
Current limiting resistors allow at least eight nodes without exceeding the maximum load of
the transceiver. Placement of the current-limiting resistors on both lines provides better
dynamic signal balance. There is generally no need for line termination resistors below data
rates of approximately 10 Mbps because the IL610 coil resistance of approximately 85 Ω is
close to the characteristic impedance of most cables. The circuit is intrinsically open-circuit
failsafe because the IL610 is guaranteed to switch to the high state when the coil input
current is less than 0.5 mA.
Number of
Nodes
1
2
3
4
5
6
7
8
Current Limit
Resistors (Ω)
None
17
22
27
27
27
30
33
www.IsoLoop.com
©NVE Corporation
12
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
IL600 Series Isolators
VDD1
VDD2
SJA1000
1
VDD1
8
VSS1
VSS2
RX1
22
20
RX0 19
C1
12
13
14
VDD2
18
VSS3
15
VDD3
TX0
TX1
1
2
2
8
7
21
VDD1
VDD2
3
6
C4
C6
C5
5
4
3
Cboost
4
1K
TXD
Rs
GND
CANH
Vcc
CANL
RXD
Vref
8
7
6
5
PCA82C250
IL612
C3
C2
Cboost
Rs
1K
GND1
GND2
Notes:
Cboost is 16 pF ceramic
All other capacitors are 47 nF ceramic
Isolated CAN Bus
Low pulse width distortion is critical for CAN bus, and IL600 Isolators are specified for just 3 ns typical pulse width distortion.
Their fail-safe output (logic high output for zero coil current) ensures proper power-on. The speed of IL600 isolators easily
supports the maximum CAN bus transfer speed of 1 Mbps.
13
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL600 Series Isolators
VDD1
VDD2
8
C1
R
Cboost
DE
ISL8487E
1
2
3
4
+
RE
16
15
14
Cboost
C3
390R
1
R
7
1K
5
+
-
12
6
Cboost
D
1K
7
8
B
13
+
11
C2
2
RE
3
DE
4
D
220R
10
9
6
IL614
A
390R
5
GND2
GND1
Notes:
Cboost is 16 pF
All other capacitors are 47 nF ceramic
Isolated RS-485 – Fractional Load
The unique IL614 three-channel isolator can be used as part of a multi-chip design with a variety of non-isolated transceivers.
The IL614 provides 2.5 kVRMS isolation (1 minute) and 20 kV/µs transient immunity. The IL614-3 is in a narrow-body
(0.15 inch-wide) package when board space is critical.
14
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL600 Series Isolators
+5 V
10-20 V
2
LM309H
600 V max..
1
3
8
IL610
1
C1
3
Hi-Drive
1K
+
2
CAPP
2
5
8
IL610
2
3
HIN
HO
LIN
VS
COM
LO
7
6
To Load
C2
3
1K
VB 8
6
Cboost
Lo-Drive
IR2102
VCC
+
6
4
5
Cboost
5
GND2
GND1
Notes:
Cboost is 16 pF
CAPP is application specific
All other capacitors are 47 nF ceramic
Single-Phase Power Control
The fail-safe output (logic high output for zero coil current) of IL600 Isolators ensures power FETs will be off on power-up.
The IL600 inputs can be configured for inverting or non-inverting operation (see Applications Information).
V DD2
CBOOST
16 pF
IL610
3
Rx
(+10V)
_
2
GND1
+
8
7
47 nF
6
Vo
5
GND2
Notes:
CBOOST is 16pF ceramic
C1 and C2 are 47 nF ceramic
Isolated RS-232 Receiver Using IL610
An IL610 can be used as a simple isolated RS-232 receiver. Most RS-232 nodes have at least 5 mA drive capability to switch
the IL610. Cabling is simplified by eliminating the need to power the input side of the receiving board. A similar circuit can be
used for RS-422/RS-485, LVDS, or other differential networks. The IL610-1 is a unique MSOP isolator when board space is
critical.
15
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL600 Series Isolators
Package Drawings
8-pin MSOP (-1 suffix)
Dimensions in inches (mm); scale = approx. 5X
0.114 (2.90)
0.122 (3.10)
0.016 (0.40)
0.027 (0.70)
0.114 (2.90)
0.122 (3.10)
0.189 (4.80)
0.197 (5.00)
0.032 (0.80)
0.043 (1.10)
0.005 (0.13)
0.009 (0.23)
0.010 (0.25)
0.016 (0.40)
0.024 (0.60)
0.028 (0.70)
0.002 (0.05)
0.006 (0.15)
NOTE: Pin spacing is a BASIC
dimension; tolerances
do not accumulate
8-pin SOIC Package (-3 suffix)
Dimensions in inches (mm); scale = approx. 5X
0.188 (4.77)
0.197 (5.00)
0.016 (0.4)
0.050 (1.3)
0.040 (1.02)
0.050 (1.27)
0.054 (1.4)
0.072 (1.8)
0.150 (3.8)
0.157 (4.0)
0.228 (5.8)
0.244 (6.2)
0.004 (0.1)
0.012 (0.3)
0.049 (1.24)
0.051 (1.30)
NOM
NOTE: Pin spacing is a BASIC
dimension; tolerances
do not accumulate
0.007 (0.2)
0.013 (0.3)
0.013 (0.3)
0.020 (0.5)
8-pin PDIP (-2 suffix)
Dimensions in inches (mm); scale = approx. 2.5X
0.28 (7.1)
0.33 (8.4)
0.24 (6.1)
0.27 (6.9)
0.30 (7.6)
0.38 (9.7)
0.13 (3.30)
0.17 (4.32)
NOTE:
Pin spacing is a BASIC
dimension; tolerances
do not accumulate
0
10
0.345 (8.76)
0.40 (10.2)
0.055 (1.40)
0.065 (1.65)
0.008 (0.2)
0.015 (0.4)
0.015 (0.38)
0.040 (1.02)
0.030 (0.76)
0.045 (1.14)
0.09 (2.3)
0.11 (2.8)
0.045 (1.14)
0.070 (1.78)
0.014 (0.36)
0.023 (0.58)
16
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL600 Series Isolators
0.15" 16-pin SOIC Package (-3 suffix)
Dimensions in inches (mm); scale = approx. 5X
0.013 (0.3)
0.020 (0.5)
NOM
0.007 (0.2)
0.013 (0.3)
0.386 (9.8)
0.394 (10.0)
Pin 1 identified
by either an
indent or a
marked dot
0.016 (0.4)
0.050 (1.3)
0.055 (1.40)
0.062 (1.58)
0.054 (1.4)
0.072 (1.8)
0.150 (3.81)
0.157 (3.99)
0.049 (1.24)
0.051 (1.30)
0.228 (5.8)
0.244 (6.2)
NOTE: Pin spacing is a BASIC
dimension; tolerances
do not accumulate
0.004 (0.1)
0.012 (0.3)
0.3" 16-pin SOIC Package (no suffix)
Dimensions in inches (mm); scale = approx. 5X
0.033 (0.85)*
0.043 (1.10)
0.260 (6.60)*
0.280 (7.11)
0.013 (0.3)
0.020 (0.5)
0.007 (0.2)
0.013 (0.3)
0.397 (10.08)
0.413 (10.49)
0.017 (0.43)*
0.022 (0.56)
0.016 (0.4)
0.050 (1.3)
0.007 (0.18)*
0.010 (0.25)
0.092 (2.34)
0.105 (2.67)
Pin 1 identified by
either an indent
or a marked dot
0.08 (2.0)
0.10 (2.5)
0.292 (7.42)*
0.299 (7.59)
0.049 (1.24)
0.051 (1.30)
0.394 (10.00)
0.419 (10.64)
NOTE: Pin spacing is a BASIC
dimension; tolerances
do not accumulate
*Specified for True 8™ package to guarantee 8 mm creepage per IEC 60601.
0.004 (0.1)
0.012 (0.3)
17
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL600 Series Isolators
Ordering Information and Valid Part Numbers
IL 610 - 1 E TR13
IL610 Valid
Part Numbers
IL612 Valid
Part Numbers
Bulk Packaging
Blank = Tube
TR7 = 7'' Tape and Reel
TR13 = 13'' Tape and Reel
IL610-1E
IL610-2E
IL610-3E
IL610-5
IL612-2E
IL612-3E
Package
E = RoHS Compliant
IL611 Valid
Part Numbers
Package Type
Blank = 0.3" SOIC
-1 = MSOP
-2 = PDIP
-3 = 0.15'' SOIC
-5 = Bare die
IL611-1E
IL611-2E
IL611-3E
IL613 Valid
Part Numbers
IL613E
IL613-3E
IL614 Valid
Part Numbers
IL614E
IL614-3E
Base Part Number
610 = Single Channel
611 = 2 Drive Channels
612 = 1 Drive Channel,
1 Receive Channel
613 = 3 Drive Channels
614 = 2 Drive Channels,
1 Receive Channel
All MSOP and SOIC part types are
available on tape and reel.
Product Family
IL = Isolators
RoHS
COMPLIANT
18
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL600 Series Isolators
Revision History
ISB-DS-001-IL600-AB
November 2013
Changes
• IEC 60747-5-5 (VDE 0884) certification.
• Upgraded from MSL 2 to MSL 1.
• Rearranged input threshold specifications so maximum is more than minimum.
ISB-DS-001-IL600-AA
Changes
• Added VDE 0884 pending.
• Updated package drawings.
• Added recommended solder pad layouts.
• Clarified circuit polarities.
ISB-DS-001-IL600-Z
Changes
• Detailed isolation and barrier specifications.
• Cosmetic changes.
ISB-DS-001-IL600-Y
Changes
• Clarified Test Circuit 2 differential operation diagram (p.5).
ISB-DS-001-IL600-X
Changes
• Separated and clarified Input Specifications.
• Added minimum/maximum coil resistance specifications.
• Merged and simplified “Operation” and “Applications” sections.
ISB-DS-001-IL600-W
Changes
• Update terms and conditions.
ISB-DS-001-IL600-V
Changes
• Additional changes to pin spacing specification on MSOP drawing.
ISB-DS-001-IL600-U
Changes
• Changed pin spacing specification on MSOP drawing.
ISB-DS-001-IL600-T
Changes
• Added typical jitter specification at 5V.
ISB-DS-001-IL600-S
Changes
• P. 2—Deleted MSOP IEC61010 approval.
ISB-DS-001-IL600-R
Changes
• Added EMC details.
ISB-DS-001-IL600-Q
Changes
• IEC 61010 approval for MSOP versions.
ISB-DS-001-IL600-P
Changes
• Specified coil resistance as typical only.
•
Revised section on calculating limiting resistors.
19
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL600 Series Isolators
Datasheet Limitations
The information and data provided in datasheets shall define the specification of the product as agreed between NVE and its customer, unless NVE and
customer have explicitly agreed otherwise in writing. All specifications are based on NVE test protocols. In no event however, shall an agreement be
valid in which the NVE product is deemed to offer functions and qualities beyond those described in the datasheet.
Limited Warranty and Liability
Information in this document is believed to be accurate and reliable. However, NVE does not give any representations or warranties, expressed or
implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information.
In no event shall NVE be liable for any indirect, incidental, punitive, special or consequential damages (including, without limitation, lost profits, lost
savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on
tort (including negligence), warranty, breach of contract or any other legal theory.
Right to Make Changes
NVE reserves the right to make changes to information published in this document including, without limitation, specifications and product descriptions
at any time and without notice. This document supersedes and replaces all information supplied prior to its publication.
Use in Life-Critical or Safety-Critical Applications
Unless NVE and a customer explicitly agree otherwise in writing, NVE products are not designed, authorized or warranted to be suitable for use in life
support, life-critical or safety-critical devices or equipment. NVE accepts no liability for inclusion or use of NVE products in such applications and such
inclusion or use is at the customer’s own risk. Should the customer use NVE products for such application whether authorized by NVE or not, the
customer shall indemnify and hold NVE harmless against all claims and damages.
Applications
Applications described in this datasheet are illustrative only. NVE makes no representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications and products using NVE products, and NVE accepts no liability for any
assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NVE product is suitable and fit for
the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customers. Customers should
provide appropriate design and operating safeguards to minimize the risks associated with their applications and products.
NVE does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s
applications or products, or the application or use by customer’s third party customers. The customer is responsible for all necessary testing for the
customer’s applications and products using NVE products in order to avoid a default of the applications and the products or of the application or use by
customer’s third party customers. NVE accepts no liability in this respect.
Limiting Values
Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the
device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the recommended
operating conditions of the datasheet is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the
quality and reliability of the device.
Terms and Conditions of Sale
In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NVE hereby expressly objects to
applying the customer’s general terms and conditions with regard to the purchase of NVE products by customer.
No Offer to Sell or License
Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication
of any license under any copyrights, patents or other industrial or intellectual property rights.
Export Control
This document as well as the items described herein may be subject to export control regulations. Export might require a prior authorization from national
authorities.
Automotive Qualified Products
Unless the datasheet expressly states that a specific NVE product is automotive qualified, the product is not suitable for automotive use. It is neither
qualified nor tested in accordance with automotive testing or application requirements. NVE accepts no liability for inclusion or use of non-automotive
qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall
use the product without NVE’s warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the
product for automotive applications beyond NVE’s specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies
NVE for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NVE’s
standard warranty and NVE’s product specifications.
20
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation
IL600 Series Isolators
An ISO 9001 Certified Company
NVE Corporation
11409 Valley View Road
Eden Prairie, MN 55344-3617 USA
Telephone: (952) 829-9217
Fax: (952) 829-9189
www.nve.com
e-mail: [email protected]
©NVE Corporation
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
ISB-DS-001-IL600-AB
November 2013
21
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
©NVE Corporation