Detectors Catalog Products (EAR99/Non-ITAR) Teledyne Microwave Solutions (TMS) offers all types of detectors with both analog and threshold designs operating from 10MHz to 26GH, with excellent power temperature stability. The detectors are MIL-PRF38534 and ISO 9001 certified, and incorporate either planar gemanium tunnel diodes or silicon Schottky diodes with video amplifiers and comparators. With over 50 ITAR-free designs, many packaging options and with up to 10nS pulse response, TMS is able to offer the right detector to meet your particular application. Typical and guaranteed specifications vary versus frequency; see detailed data sheets for specification variations. High Performance Analog Detectors Typical and Guaranteed Specifications—50 Ω System Input Power Range dBm Model Frequency Range GHz Typ. Min. -55/85C Power Flatness ±dB Typ. Power Temperature Stability ±dB Max. -55/85C Typ. Sensitivity Vout @ Pref mV Max. -55/85C Sq. Pulse Law Response Dep. µsec dBm Min. Typ. -55/85C Pref. Typ. Typ. VSWR Input Max. Typ. -55/85C DC Sup. Volt. Cur. no RF ±V ±mA 12 Available in standard 0.250-in. sq., 0.450-in. sq., Surface Mount or TO-8 Packages (depending on model) UTD-1000 .01-1.0 -20 to 5 -20 to 5 0.70 1.25 1.00 1.50 120 80 -10 1.5 2.0 UTD-1001V .01-1.0 -20 to 5 -20 to 5 0.80 1.25 1.00 1.50 120 80 -10 — 2.0 PSD-2001-25 PSD-4001-25 .02-2.0 .01-4.0 -20 to 10 -35 to 10 -15 to 5 -30 to 0 0.10 0.30 0.3 0.75 0.50 0.75 1000 125 900 90 0 -15 -15 2.00 3.00 1.5 1.5 1.8 2.0 +15 only +15 only 15 15 DAC4101 DAC4103 0.01–4.0 0.01–4.0 -30 to 5 -10 to 25 -25 to 0 -5 to 20 0.60 0.60 0.75 0.75 0.25 0.25 0.50 0.40 120 120 90 90 -15 5 -10 +10 1.50 1.50 1.5 1.2 1.8 1.5 5 5 2 2 DAQ6101 DAQ6103 DAQ6104 DAQ6116 0.1–6.0 0.1–6.0 0.1–6.0 0.1–6.0 -30 to 5 -10 to 25 -25 to 12 -5 to 25 -25 to 0 -5 to 20 -20 to 10 0 to 20 0.50 0.50 0.75 0.50 0.75 0.75 1.00 0.75 0.25 0.25 0.50 0.40 0.50 0.50 0.75 0.50 120 120 190 180 90 90 150 90 -15 5 -10 0 -10 +10 -10 N/A 1.50 1.50 0.30 360.0 1.5 1.2 1.5 1.5 2.0 1.5 2.0 2.0 5 5 5 N/A 2 2 2 N/A PSD-6001-25 1.5-6.0 -35 to 10 -30 to 0 0.30 0.75 0.50 0.75 125 90 -15 -15 3.00 1.5 2.0 15 2 DAS8121‡ 0.5–8.0 DAS10241 1.0–10.0 DAQ10501 0.05–10.0 DACP18001* 0.1–18.0 -30 to 5 -40 to 0 -30 to 5 -30 to 5 -25 to 0 -35 to -5 -25 to 0 -25 to 0 0.50 1.00 0.75 0.50 0.75 1.50 1.00 1.00 0.40 0.50 0.25 0.25 0.50 1.00 0.50 0.50 140 160 120 140 90 100 90 100 -15 -15 -15 -15 -10 -13 -10 -10 0.02 0.005 1.50 0.30 1.5 1.5 1.5 1.5 2.0 2.0 2.0 2.0 5 5 5 5 9 15 2 3 DACP20021*‡ 0.5–20.0 DA2CP20047‡ 0.5-22.0 -30 to 5 -25 to +20 -25 to 0 -20 to +20 0.75 1.00 1.00 1.50 0.40 0.40 0.50 1.50 140 0.7 90 0.65 -15 0 -10 N/A 0.02 90mS 1.5 1.6 2.3 2.0 5 5 9 1.5 Current data sheets available on website. * Available only in one-stage CougarPak® V Input Impedance greater than 300 ohms. ‡ Parameter is -40 to 85 °C 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] 12 2 2 Typical and guaranteed specifications vary versus frequency; see detailed data sheets for specification variations. High Performance Threshold Detectors Typical and Guaranteed Specifications—50 Ω System Input Power Range dBm Model Frequency Range GHz Typ. Min. -55/85C Power Flatness ±dB Typ. Max. -55/85C Power Temperature Stability ±dB Typ. Max. -55/85C Hysteresis dB Output Logic Typ. Pulse Response µsec Typ. VSWR Input Volt. V Max. Typ. -55/85C Cur. mA Typ. Typ. Available in standard 0.250-in. sq., Models 0.450-in. sq., by Surface or TO-8 Packages (depending on model) listed modelMount number UTD-2002 UTD-2004 .01-2.0 .01-2.0 -10 to +10 -25 to -10 -10 to +10 -25 to -10 0.5 0.5 1 1 1 1.5 1.5 1.5 0.1 0.7 TTL TTL 0.08 300 1.3 1.8 2 2.2 15 5 12 2.5 DTC4001 DTCH4003 0.01-4.0 0.01–4.0 -30 to -5 -10 to 20 -25 to -5 -5 to 15 0.5 0.5 0.75 0.75 0.25 0.2 0.5 0.4 0.2 0.2 TTL TTL 50 50 1.5 1.2 2 1.8 5 5 2.5 3 PSD-6002-25 0.1-6.0 -10 to +10 -10 to +10 0.7 1 1 1.5 0.1 TTL 0.08 1.5 2 15 12 DTQ6001 DTC6002 DTS6014 DTS6015 0.1–6.0 0.01-6.0 0.1–6.0 0.1–6.0 -30 to -5 -30 to -5 -12 to 12 -30 to -5 -25 to -5 -25 to -5 -10 to 10 -25 to -5 0.5 0.5 0.5 0.5 0.75 0.75 0.75 0.75 0.25 0.25 0.3 0.25 0.5 0.5 0.75 0.5 0.2 0.2 0.3 0.2 TTL TTL TTL TTL 50 50 0.8 15 1.5 1.5 1.5 1.5 2 2 2 2 5 5 5 5 6 2.5 2 2.5 DTS8003‡ DTS8031‡ 0.1–8.0 0.5–8.0 -10 to 15 -15 to -3 -5 to 15 -15 to -5 0.5 0.5 0.75 0.75 0.25 0.25 0.5 0.5 0.2 0.2 TTL TTL 50 0.005 1.2 1.5 1.7 2 5 5 1 7 -30 to -5 -15 to -3 -15 to -3 -20 to -5 -12 to -5 -12 to -5 0.75 0.5 1.25 1.0 0.75 1.5 0.25 0.25 0.25 0.5 0.5 0.5 0.5 0.2 0.02 TTL TTL TTL 50 0.01 0.008 1.5 1.5 1.5 2 2 2.8 5 5 5 2.5 7 7 DTCP18001* 0.01–18.0 DTCP18031* 0.5–18.0 DTCP20231*‡ 0.7–20.0 Current data sheets available on website. *Available only in one-stage CougarPak®. ‡ Parameter is -40 to 85 °C 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] Rev. 2/16 0.01 TO 4.0 GHz THRESHOLD DETECTOR DTC4001 DTC4001 Typical Values @ +25 °C Wide Frequency Range. . . . . . . . . . . . . . . . . . . . . . . . . 0.01 to 4.0 GHz Wide Power Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30.0 to -5.0 dBm Temperature Stability . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.5 dB Power Flatness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.5 dB Standard Size TO-8 or Surface Mount Package External Adjustable Threshold Level, Fast Response Time, Low Drift, Insensitive Threshold Level to Applied Voltage DTC4001 TO-8 Package for Detectors SPECIFICATIONS* Parameter Typical Frequency (Min.) Input Power Range (Min.) VSWR (Max.) Power Flatness (Max.) Guaranteed 0 to 50 °C -55 to +85 °C 0.01-5.0 GHz 0.01-4.0 GHz 0.01-4.0 GHz 1.5:1† 2.0:1† 2.0:1† -30 to -5 dBm* ±0.5 dB^ -25 to -5 dBm* -25 to -5 dBm* ±0.75 dB^ ±0.75 dB^ Threshold Temperature Stability (Max.) ±0.25 dB^ Pulse Response (Max.) 50 µsec^‡ 100 µsec^‡ 100 µsec^‡ Output Voltage Hi @ 5mA source 4.4 Volts 3.5 Volts 3.5 Volts Supply Current (Max.) 2.5 mA† Threshold Hysteresis (Max.) Logic: Pin > Pth Output Voltage Lo @ 5mA sink ±0.2 dB 1 0.1 Volts ±0.5 dB^ ±0.5 dB^ ±0.5 dB ±0.5 dB 1 1 0.25 Volts 0.25 Volts 3.5 mA† 3.5 mA† * Measured in a 50 Ohm system at Vs=+5.0 Vdc. RTH=100 Ohm to 100 KOhm unless otherwise specified. ^ RTH = 1 KOhm. † Pin ≤–15 dBm. ‡ 50% RF to 10 or 90% Video Response time for input change ≥3 dB above Pth. MAXIMUM RATINGS DC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . Operating Case Temperature . . . . . . . . . . . . . . . . . . . . Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . RF Input Power Thermal Resistance (θjc, RF) . . . . . . . DC Supply Thermal Resistance (θjc, DC) . . . . . . . . . . . Temperature Rise @ 0 dBm . . . . . . . . . . . . . . . . . . . . . DTS4001 SMTO-8 Package for Detector +7 V +14.0 dBm -55 °C to +125 °C -65 °C to +125 °C +125 °C +3.5 °C/mW +32 °C/W +4.1 °C APPLICATION NOTES This unit is DC coupled and employs a RF choke at the input (DC short). DO NOT bypass the Threshold Control pin. Capacitance greater than 50pF may cause instabilities. Keep the threshold programming resistor or circuit close to this pin. Average power detection is obtained at power levels below approximately –13 dBm. The output of this unit is derived from an op-amp, not a true logic device. Connect external threshold resistor from Rcntl port to ground. DIMENSIONS ARE IN INCHES [MILLIMETERS] 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] DTC4001 TYPICAL PERFORMANCE Input VSWR -20.0 2.00 -21.0 1.75 VSWR RF INPUT - dBm Threshold Power @ R = 100 KEY: +25 C +85 C Ohms -55 C -22.0 1.50 -23.0 1.25 -24.0 1.00 0.0 -25.0 0.5 1.0 1.5 2.0 2.5 FREQUENCY - GHz 3.0 -26.0 0.0 0.5 1.0 1.5 2.0 2.5 FREQUENCY - GHz 3.0 3.5 4.0 4.5 3.5 4.0 4.5 Threshold Power @ R = 1 KOhms -13.0 RF INPUT - dBm -14.0 -15.0 -16.0 -17.0 -18.0 -19.0 0.0 0.5 1.0 1.5 2.0 2.5 FREQUENCY - GHz 3.0 Pulse Response @ RTH =100 Ohms Threshold Power @ R = 20 KOhms -2.0 RF INPUT - dBm -3.0 -4.0 -5.0 -6.0 -7.0 -8.0 0.0 0.5 1.0 1.5 2.0 2.5 FREQUENCY - GHz 3.0 3.5 4.0 4.5 Control Resistance vs. Threshold Power (dBm) 1000000 Pulse Response @ RTH = 1 KOhms Control Resistance (Ohm) 100000 10000 1000 Pulse Response @ RTH = 20 KOhms 100 10 1 -55 -45 -35 -25 -15 THRESHOLD POWER - dBm -5 5 Top Trace: TTL Logic Out Bottom Trace: RF Input Time Base: 5.0 µs/div 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] 3.5 4.0 4.5 Rev. 7/10 0.01 TO 4.0 GHz ANALOG DETECTOR DAC4101 DAC4101 Typical Values @ +25 °C Wide Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.01 to 4.5 GHz Wide Power Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –30.0 to +5.0 dBm Temperature Stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.25 dB Power Flatness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.6 dB Low VSWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5:1 Single Power Supply Standard Size TO-8 Package DAC4101 TO-8 Package for Detectors SPECIFICATIONS* Parameter Typical Guaranteed 0 to 50 °C -55 to +85 °C Frequency (Min.) 0.01-4.5 GHz 0.01-4.0 GHz 0.01-4.0 GHz Input Power Range (Min.) -30 to +5 dBm -25 to 0 dBm -25 to 0 dBm 1.5:1† 1.8:1† 1.8:1† 120 mV† 90 mV† 90 mV† Power Flatness (Max.) ±0.6 dB^ ±0.75 dB^ ±0.75 dB^ Temperature Stability (Max.) ±0.25 dB^ ±0.5 dB^ ±0.5 dB^ Output Offset Voltage, no RF (Max.) +0.5 mV +2.0 mV +2.0 mV 1 dB Square Law Departure -10 dBm — — Tangential Sensitivity -45 dBm^^ — — Pulse Response, Pin = -15 dBm 1.5 µsec‡ — — Pulse Response, Pin = 5 dBm 4.0 µsec‡ — — Max Output Voltage Vs-1 Volts — — VSWR (Max.) Sensitivity, Vout (Min.) Supply Current, no RF 2 +mA, 2 -mA Supply Current, Pin = 5 dBm 9 +mA, 2 -mA DAS4101 * 50-Ohm source impedance, 2 KΩ||50 pF output load, +5 Vdc. † Pin = –15 dBm. ^ Vout = 100 mV. ^^ 3 dB NF, 1 MHz Bandwidth. ‡ 50% RF to 10 or 90% Video. SMTO-8 Package for Detectors MAXMUM RATINGS DC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . Operating Case Temperature . . . . . . . . . . . . . . . . . . . . Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Detector Thermal Resistance1 (θjc) . . . . . . . . . . . . . . . Temperature Rise @ 0 dBm (Tjc) . . . . . . . . . . . . . . . . . Temperature Rise @ 5 dBm (Tjc) . . . . . . . . . . . . . . . . . 1 Thermal +18 V +14.0 dBm -55 °C to +100 °C -65 °C to +125 °C +100 °C +3500 °C/Watt +3.5 °C +35 °C resistance is based on RF input power. Ratings based on +25 °C. APPLICATION NOTES This unit is DC coupled and employs a RF choke at the input (DC short). If the application calls for the input to sink current there will be approximately an additional 1 mV of output offset voltage for each 3 mA of current. Sink current should be limited to 100 mA max to avoid choke burnout. For higher supply voltages, up to ±15 volts, the positive supply pin must include a series current limiting resistor, Rs = (Vs – 5) / 0.01 (e.g., Vs = +15v, Rs = 1.0KΩ). Average power detection is obtained at power levels below approximately –13 dBm. For best pulse response the supply pins should be bypassed with an additional 1.0 µF capacitor. The unit contains 0.01 µF internal capacitors. DIMENSIONS ARE IN INCHES [MILLIMETERS] 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] DAC4101 TYPICAL PERFORMANCE INPUT POWER - dBm Input Flatness @ Vo = 100 mV KEY: +25 °C +85 °C -55 °C -14.0 -15.0 -16.0 -17.0 -18.0 0.01 0.06 0.1 .6 1.1 1.6 2.1 FREQUENCY - GHz 2.6 3.1 3.6 4.1 INPUT POWER - dBm Input Flatness @ Vo = 1.0 V -2.0 -3.0 Pulse Response @ Pin = –15 dBm -4.0 -5.0 -6.0 0.01 0.06 0.1 .6 1.1 1.6 2.1 FREQUENCY - GHz 2.6 3.1 3.6 4.1 2.6 3.1 3.6 4.1 INPUT POWER - dBm Input Flatness @ Vo = 3.0 V 6.0 5.0 4.0 3.0 2.0 0.01 0.06 0.1 .6 1.1 1.6 2.1 FREQUENCY - GHz Input VSWR @ Pin = -15 dBm 2.00 Pulse Response @ Pin = 5 dBm VSWR 1.75 1.50 1.25 1.00 0.01 0.06 0.1 .6 1.1 1.6 2.1 FREQUENCY - GHz 2.6 3.1 3.6 4.1 Transfer Curve @ 1.0 GHz 10.0 OUTPUT VOLTAGE - VOLTS 1.0 0.1 0.01 0.001 0.0001 -50 -40 -30 -20 -10 INPUT POWER - dBm 0 10 20 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] Rev. 7/10 DAC4103 0.01 TO 4.0 GHz ANALOG DETECTOR DAC4103 Typical Values @ +25 °C Wide Frequency Range. . . . . . . . . . . . . . . . . . . . . . . . . 0.01 to 4.0 GHz Wide Power Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . –10.0 to +25.0 dBm Temperature Stability . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.25 dB Power Flatness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.6 dB Low VSWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2:1 Single Power Supply Standard Size TO-8 Package DAC4103 TO-8 Package for Analog Detectors SPECIFICATIONS* Typical Guaranteed -55 to +85 °C Frequency (Min.) 0.01-4.5 GHz 0.01-4.0 GHz Input Power Range (Min.) -10 to+ 25 dBm -5 to +20 dBm Parameter VSWR (Max.) 1.2:1† 1.5:1† 120 mV† 90 mV† Power Flatness (Max.) ±0.6 dB^ ±0.75 dB^ Temperature Stability (Max.) ±0.25 dB^ ±0.4 dB^ Output Offset Voltage, no RF (Max.) ±0.5 mV +2.0 mV 1 dB Square Law Departure +10 dBm — Tangential Sensitivity -5 dBm^^ — 1.5 µsec‡ — Pulse Response, Pin = +25 dBm 3.0 µsec‡ — Max Output Voltage Vs-1 Volts Sensitivity, Vout (Min.) Pulse Response, Pin = +5 dBm Supply Current, no RF 2 +mA Supply Current, Pin = +25 dBm 10 +mA — DAS4103 * Measured in a 50-Ohm system at +5 Vdc, 2 KΩ||50 pF unless otherwise specified. † Pin = +5 dBm. ^ Vout = 100 mV. ^^ 3 dB NF, 1 MHz Bandwidth. ‡ 50% RF to 10 or 90% Video. SMTO-8 Package for Analog Detectors MAXMUM RATINGS DC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . Operating Case Temperature . . . . . . . . . . . . . . . . . . . . Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Detector Thermal Resistance1 (θjc) . . . . . . . . . . . . . . . Temperature Rise @ +20 dBm (Tjc) . . . . . . . . . . . . . . . 1 Thermal ±18 V +27.0 dBm -55 °C to +100 °C -65 °C to +125 °C +100 °C +3500 °C/Watt +3.5 °C resistance is based on RF input power. Ratings based on +25 °C. APPLICATION NOTES This unit is DC coupled and employs a RF choke at the input (DC short). If the application calls for the input to sink current there will approximately be an additional 1 mV of output offset voltage for each 3 mA of current. Sink current should be limited to 100 mA max to avoid choke burnout. For higher supply voltages, up to ±15 volts, the positive supply pin must include a series current limiting resistor, Rs = (Vs – 5)/0.01. (e.g.: Vs = 15v, Rs = 1K) Average power detection is obtained at power levels below approximately +7 dBm. For best pulse response both supply pins should be bypassed with an additional 1.0 µF capacitor. The unit contains 0.01 µF internal capacitors. DIMENSIONS ARE IN INCHES [MILLIMETERS] 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] DAC4103 TYPICAL PERFORMANCE Input Flatness @ Vo = 100 mV KEY: +25 °C +85 °C -55 °C INPUT POWER 6.0 5.0 4.0 3.0 2.0 0.01 0.06 0.1 .6 1.1 1.6 2.1 FREQUENCY - GHz 2.6 3.1 3.6 4.1 Input Flatness @ Vo = 1.0 V INPUT POWER 18.0 17.0 Pulse Response @ Pin = +5 dBm 16.0 15.0 14.0 0.01 0.06 0.1 .6 1.1 1.6 2.1 FREQUENCY - GHz 2.6 3.1 3.6 4.1 2.6 3.1 3.6 4.1 Input Flatness @ Vo = 3.0 V INPUT POWER 26.0 25.0 24.0 23.0 22.0 0.01 0.06 0.1 .6 1.1 1.6 2.1 FREQUENCY - GHz Input VSWR @ Pin = +5 dBm 1.75 Pulse Response @ Pin = +25 dBm VSWR 1.50 1.25 1.00 0.75 0.01 0.06 0.1 .6 1.1 1.6 2.1 FREQUENCY - GHz 2.6 3.1 3.6 4.1 Transfer Curve @ 1.0 GHz 10.0 OUTPUT VOLTAGE - VOLTS 1.0 0.1 0.01 0.001 0.0001 -20 -10 0 +10 +20 INPUT POWER - dBm +30 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] Rev. 7/10 0.1 TO 6.0 GHz THRESHOLD DETECTOR DTQ6001 DTQ6001 Typical Values @ +25 °C Wide Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . Wide Power Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature Stability . . . . . . . . . . . . . . . . . . . . . . . . . . Power Flatness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cougar Q Package 0.1 to 6.0 GHz -30.0 to -5.0 dBm ± 0.50 dB ± 0.50 dB DTQ6001 SM-25 for Detectors SPECIFICATIONS* Parameter Typical Frequency (Min.) Input Power Range (Min.) VSWR (Max.) Power Flatness (Max.) Threshold Temperature Stability (Max.) Threshold Hysteresis Pulse Response Logic: Pin > Pth Guaranteed 0 to 50 °C -55 to +85 °C 0.1-7.0 GHz 0.1-6.0 GHz 0.1-6.0 GHz -30 to -5 dBm* -25 to -5 dBm* -25 to -5 dBm* 1.5:1† 2.0:1† 2.0:1† ±0.5 dB ±0.75 dB ±0.75 dB ±0.25 dB^ ±0.5 dB^ ±0.5 dB^ ±0.2 dB ±0.5 dB ±0.5 dB 15 µsec^‡ 50 µsec^‡ 50 µsec^‡ 1 1 1 Output Voltage Hi @ 5mA source 4.4 Volts 3.5 Volts 3.5 Volts Output Voltage Lo @ 5mA sink 0.1 Volts 0.5 Volts 0.5 Volts 6.0 mA 8.0 mA 8.0 mA Supply Current * Measured in a 50 Ohm system at Vs=+5.0 Vdc. Rth = 10 to 100 KOhm. ^ Rth = 100 to 20 KOhm. † Pin ≤–15 dBm. ‡ 50% RF to 10 or 90% Video Response time for input change ≥3 dB above Pth. MAXMUM RATINGS DC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . Operating Case Temperature . . . . . . . . . . . . . . . . . . . . Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Detector Thermal Resistance1 (θjc) . . . . . . . . . . . . . . . Temperature Rise @ 0 dBm . . . . . . . . . . . . . . . . . . . . . 1 Thermal +5 V +14.0 dBm -55 °C to +100 °C -65 °C to +125 °C +100 °C +3500 °C/Watt +3.5 °C resistance is based on RF input power. Ratings based on +25 °C. APPLICATION NOTES This unit is DC coupled and employs a RF choke at the input (DC short). DO NOT bypass the Threshold Control pin. Capacitance greater than 50pF may cause instabilities. Keep the threshold programming resistor or circuit close to this pin. Average power detection is obtained at power levels below approximately –13 dBm. The output of this unit is derived from an op-amp, not a true logic device. Connect external threshold resistor from Rcntl port to ground. DIMENSIONS ARE IN INCHES [MILLIMETERS] 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] 3.0 3.5 4.0 4.5 5.0 5.5 DTQ6001 6.0 TYPICAL PERFORMANCE Threshold Power @ R = 100 KEY: +25 °C +85 °C Ohms -55 °C Control Resistance vs. Threshold Power (dBm) 1000000 -21.0 100000 -23.0 3.0 -24.0 3.5 4.0 4.5 5.0 5.5 6.0 -25.0 -26.0 -27.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 FREQUENCY - GHz 4.0 4.5 5.0 5.5 6.0 Control Resistance (Ohm) RF INPUT - dBm -22.0 10000 1000 100 Threshold Power @ R = 1 KOhms -13.0 RF INPUT - dBm R -14.0 10 -40 -30 -20 -10 THRESHOLD POWER - dBm -15.0 3.0 -16.0 3.5 4.0 4.5 5.0 5.5 6.0 0 10 1 -17.0 -18.0 -19.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 FREQUENCY - GHz 4.0 4.5 5.0 5.5 6.0 Threshold Power @ R = 20 KOhms -2.0 3.0 RF INPUT - dBm -3.0 3.5 4.0 4.5 5.0 5.5 6.0 -4.0 Pulse Response @ 100 Ohms -5.0 -6.0 -7.0 -30 -20 -10 -8.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 FREQUENCY - GHz 4.0 4.5 5.0 5.5 6.0 Input VSWR 2.00 VSWR 1.75 1.50 Pulse Response @ 1 KOhms 1.25 1.00 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 FREQUENCY - GHz 4.0 4.5 5.0 5.5 6.0 Pulse Response @ 20 KOhms Top Trace: TTL Logic Out Bottom Trace: RF Input Time Base: 5.0 µs/div 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] 0 10 Rev. 7/10 0.01 TO 6.0 GHz THRESHOLD DETECTOR DTC6002 DTC6002 Typical Values @ +25 °C Wide Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . 0.01 to 6.0 GHz Wide Power Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30.0 to -5.0 dBm Temperature Stability . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.50 dB Power Flatness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.50 dB Standard Size TO-8 or Surface Mount Package External Adjustable Threshold Level, Fast Response Time, Low Drift, Insensitive Threshold Level to Applied Voltage DTC6002 TO-8 Package for Detectors SPECIFICATIONS* Parameter Typical Guaranteed 0 to 50 °C -55 to +85 °C Frequency (Min.) 0.01-7.0 GHz 0.01-6.0 GHz 0.01-6.0 GHz Input Power Range (Min.) -30 to -5 dBm* -25 to -5 dBm* -25 to -5 dBm* 1.5:1† 2.0:1† 2.0:1† Power Flatness (Max.) ±0.5 dB^ ±0.75 dB^ ±0.75 dB^ Threshold Temperature Stability (Max.) ±0.25 dB^ ±0.5 dB^ ±0.5 dB^ ±0.2 dB ±0.5 dB ±0.5 dB 50 µsec^‡ 100 µsec^‡ 100 µsec^‡ 1 1 1 Output Voltage Hi @ 5mA source 4.4 Volts 3.5 Volts 3.5 Volts Output Voltage Lo @ 5mA sink 0.1 Volts 0.25 Volts 0.25 Volts Supply Current (Max.) 2.5 mA† 5.0 mA† 5.0 mA† VSWR (Max.) Threshold Hysteresis (Max.) Pulse Response (Max.) Logic: Pin > Pth DTS6002 * Measured in a 50 Ohm system at Vs=+5.0 Vdc. RTH=100 Ohm to 100 KOhm unless otherwise specified. ^ RTH = 1 KOhm. † Pin ″–15 dBm. ‡ 50% RF to 10 or 90% Video Response time for input change ≥3 dB above Pth. SMTO-8 Package for Detector MAXMUM RATINGS DC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . Operating Case Temperature . . . . . . . . . . . . . . . . . . . . Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Detector Thermal Resistance1 (θjc) . . . . . . . . . . . . . . . Temperature Rise @ 0 dBm . . . . . . . . . . . . . . . . . . . . . 1 Thermal +7 V +14.0 dBm -55 °C to +125 °C -65 °C to +125 °C +125 °C +3500 °C/Watt +3.5 °C resistance is based on RF input power. Ratings based on +25 °C. APPLICATION NOTES This unit is DC coupled and employs a RF choke at the input (DC short). DO NOT bypass the Threshold Control pin. Capacitance greater than 50pF may cause instabilities. Keep the threshold programming resistor or circuit close to this pin. Average power detection is obtained at power levels below approximately –13 dBm. The output of this unit is derived from an op-amp, not a true logic device. Connect external threshold resistor from Rcntl port to ground. DIMENSIONS ARE IN INCHES [MILLIMETERS] 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] DTC6002 R TYPICAL PERFORMANCE 3.5 4.0 4.5 5.0 5.5 6.0 2.5 3.0 3.5 FREQUENCY - GHz 4.0 4.5 5.0 5.5 6.0 Input VSWR -20.0 2.00 -21.0 1.75 VSWR RF INPUT - dBm Threshold Power @ R = 100 3.0 KEY: +25 °C +85 °C Ohms -55 °C -22.0 1.50 -23.0 1.25 -24.0 1.00 0.0 -25.0 0.5 1.0 1.5 2.0 -26.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 FREQUENCY - GHz 4.0 4.5 5.0 5.5 6.0 Threshold Power @ R = 1 KOhms -13.0 RF INPUT - dBm -14.0 -15.0 -16.0 1 -17.0 -18.0 -19.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 FREQUENCY - GHz 4.0 4.5 5.0 5.5 6.0 Pulse Response @ RTH =100 Ohms Threshold Power @ R = 20 KOhms -2.0 RF INPUT - dBm -3.0 -4.0 -5.0 -6.0 -7.0 -8.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 FREQUENCY - GHz 4.0 4.5 5.0 5.5 6.0 Pulse Response @ RTH = 1 KOhms Pulse Response @ RTH = 20 KOhms Top Trace: TTL Logic Out Bottom Trace: RF Input Time Base: 5.0 µs/div 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] Rev. 7/10 0.1 TO 6.0 GHz THRESHOLD DETECTOR DTS6014 DTS6014 Typical Values @ +25 °C Wide Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . 0.05 to 8.0 GHz Wide Power Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . -12.0 to +12.0 dBm Fast Response Time . . . . . . . . . . . . . . . . . . . . . . . . . . . 800 ηsec TTL Output Compatibility External Adjustable Threshold Level, Low Drift Standard SMTO-8 Package DTC6014 TO-8 Package for Detectors SPECIFICATIONS* Parameter Typical Guaranteed 0 to 50 °C -55 to +85 °C Frequency (Min.) 0.05-8.0 GHz 0.1-6.0 GHz 0.1-6.0 GHz Input Power Range (Min.) VSWR (Max.) Power Flatness (Max.) Threshold Temperature Stability (Max.) @ -10 dBm Input Power @ 0 dBm Input Power @ +10 dBm Input Power Pulse Response (Max.) Rise Time (10% DC to 90% DC) Fall Time (90% DC to 10% DC) Total Response Time (50% RF to 10% or 90% DC) Supply Current (Max.) (no RF) Supply Current (Max.) Pin = +5.0 dBm Threshold Hysteresis @ -10 to -1 dBm Input Power @ 0 to +10 dBm Input Power Control Terminate Current (Max.) Output Compatibility -12 to +12 dBm 1.5:1 ±0.5 dB -10 to +10 dBm 2.0:1 ±0.75 dB -10 to +10 dBm 2.0:1 ±0.75 dB ±0.75 dB ±0.5 dB ±0.3 dB ±1.0 dB ±0.75 dB ±0.6 dB ±1.0 dB ±1.0 dB ±0.75 dB 360 ηsec^ 65 ηsec^ 700 ηsec^ 150 ηsec^ 1000 ηsec^ 200 ηsec^ 800 ηsec^ 2 mA 1500 ηsec^ 4 mA 2000 ηsec^ 5 mA 2 mA 4 mA 5 mA ±1.0 dB† ±0.3 dB† 0.3 mA TTL ±1.5 dB† ±1.0 dB† 1.0 mA TTL ±2.0 dB† ±1.5 dB† 1.0 mA TTL *Measured in a 50 Ohm system at +5.0 Vdc. RTH=120 to 2800 Ohm unless otherwise specified. 1 MOhm ÁÁ8pF output load. ^ Input change ≥3 dBm above P threshold and applied for entire dynamic range. † Apply for both resistance and voltage control. DTS6014 SMTO-8 for Detectors MAXMUM RATINGS DC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . Operating Case Temperature . . . . . . . . . . . . . . . . . . . . Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Detector Thermal Resistance1 (θjc) . . . . . . . . . . . . . . . Temperature Rise @ 10 dBm (Tjc) . . . . . . . . . . . . . . . . 1 Thermal +20 V +20.0 dBm -55 °C to +125 °C -65 °C to +150 °C +150 °C +800 °C/Watt +8 °C resistance is based on RF input power. Ratings based on +25 °C. APPLICATION NOTES DTS6014 is a sensitive microwave threshold detector which provides efficient and accurate RF level measurement. DTS6014 is configured using two Schottky diode detectors, high precision comparator, and a compensated voltage reference to provide excellent temperature stability. DTS6014 is specifically designed for system built-in test and channel RF activity monitoring. The output of this unit is derived from a comparator, a true TTL logic device. Average power detection is obtained at power levels below approximately 0 dBm. DTS6014 contains open-collector comparator with internal 5.1 KOhm pull-up resistor. Pulse response (Low-to-Hi state) can be sped up by using external pull-up resistor. Max sink current is 6.0 mA. Connect external threshold resistor from Rcntl port to ground. DIMENSIONS ARE IN INCHES [MILLIMETERS] 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] + DTS6014 TYPICAL PERFORMANCE + Control Resistance vs. Threshold Power (dBm) 10000 Control Resistance (Ohm) RF INPUT - dBm -9.0 -10.0 -11.0 -12.0 -13.0 0.0 1.0 2.0 3.0 4.0 5.0 FREQUENCY - GHz 6.0 7.0 Control Resistance (Ohm) Threshold Power @ R = 700 Ohm 1.0 0.0 -1.0 -2.0 1000 100 10 -20 8.0 2.0 RF INPUT - dBm LOG SCALE 1 -8.0 -15 -10 1.0 2.0 3.0 4.0 5.0 FREQUENCY - GHz 6.0 7.0 Control C t l Resistance vs. Threshold Power (dBm) 3000 LINEAR SCALE 2000 1000 0 -20 -15 -15 -10 -10 Control Resistance (Ohm) RF INPUT - dBm -10 -5 0 5 10 15 10.0 9.0 8.0 1.0 2.0 3.0 4.0 5.0 FREQUENCY - GHz 10 10 15 15 2500 5000 Control Resistance 4000 -15 6.0 7.0 8.0 6.0 7.0 8.0 -10 -5 0 5 T 3000 -10 -15 -5 0 Control Voltage 5 10 2000 10 1500 2000 1000 1000 500 0 -15 7.0 0.0 -5 00 55 -5 THRESHOLD POWER - dBm Control Voltage and Resistance vs. Input Power (dBm) 12.0 -15 15 8.0 Threshold Power @ R = 2800 Ohm 11.0 10 4000 -3.0 0.0 -5 0 5 THRESHOLD POWER - dBm -10 -5 0 5 10 THRESHOLD POWER - dBm Control Voltage (mV) Threshold Power @ R = 120 KEY: +25 °C +85 °C Ohm -55 °C 15 0 15 Input VSWR at Pin = 0 dBm C 1.75 VSWR 1.50 1.25 1.00 0.75 0.0 1.0 2.0 3.0 4.0 5.0 FREQUENCY - GHz Input VSWR at Pin = -10 dBm Pulse Response @ RTH =120 Ohms 1.75 VSWR 1.50 1.25 1.00 0.75 0.0 1.0 2.0 3.0 4.0 5.0 FREQUENCY - GHz 6.0 7.0 8.0 Pulse Response @ RTH = 2800 Ohms Pulse Response @ RTH = 120 Ohms (with 1KOhm Pull-up Resistor) Top Trace: TTL Logic Out Bottom Trace: RF Input Time Base: 200 ηs/div 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] 15 Rev. 7/10 0.1 TO 6.0 GHz THRESHOLD DETECTOR DTS6015 DTS6015 Typical Values @ +25 °C Wide Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . 0.1 to 6.0 GHz Wide Power Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30.0 to -5.0 dBm Temperature Stability . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.25 dB Power Flatness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.50 dB Standard SMTO-8 Package External Adjustable Threshold Level, Fast Response Time, Low Drift DTS6015 SMTO-8 for Detectors SPECIFICATIONS* Parameter Typical Frequency (Min.) Guaranteed 0 to 50 °C -55 to +85 °C 0.1-7.0 GHz 0.1-6.0 GHz 0.1-6.0 GHz -30 to -5 dBm* -25 to -5 dBm* -25 to -5 dBm* 1.5:1† 2.0:1† 2.0:1† ±0.5 dB ±0.75 dB ±0.75 dB ±0.25 dB^ ±0.5 dB^ ±0.5 dB^ ±0.2 dB ±0.5 dB ±0.5 dB Pulse Response 15 µsec^‡ 50 µsec^‡ 50 µsec^‡ Logic: Pin > Pth 1 1 1 Output Voltage Hi @ 5mA source 4.4 Volts 3.5 Volts 3.5 Volts Output Voltage Lo @ 5mA sink 0.1 Volts 0.5 Volts 0.5 Volts 2.5 mA 5.0 mA 5.0 mA Input Power Range (Min.) VSWR (Max.) Power Flatness (Max.) Threshold Temperature Stability (Max.) Threshold Hysteresis Supply Current * Measured in a 50 Ohm system at Vs=+5.0 Vdc. RTH=10 to 100 KOhm unless otherwise specified. ^ RTH = 1 KOhm. †Pin ≤–15 dBm. ‡ 50% RF to 10 or 90% Video Response time for input change ≥3 dB above Pth. MAXMUM RATINGS DC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . Operating Case Temperature . . . . . . . . . . . . . . . . . . . . Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Detector Thermal Resistance1 (θjc) . . . . . . . . . . . . . . . Temperature Rise @ 0 dBm . . . . . . . . . . . . . . . . . . . . . 1 Thermal +7 V +14.0 dBm -55 °C to +100 °C -65 °C to +125 °C +100 °C +3500 °C/Watt +3.5 °C resistance is based on RF input power. Ratings based on +25 °C. APPLICATION NOTES This unit is DC coupled and employs a RF choke at the input (DC short). DO NOT bypass the Threshold Control pin. Capacitance greater than 50pF may cause instabilities. Keep the threshold programming resistor or circuit close to this pin. Average power detection is obtained at power levels below approximately –13 dBm. The output of this unit is derived from an op-amp, not a true logic device. Connect external threshold resistor from Rcntl port to ground. DIMENSIONS ARE IN INCHES [MILLIMETERS] 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] DTS6015 R TYPICAL PERFORMANCE 3.5 4.0 4.5 5.0 5.5 6.0 2.5 3.0 3.5 FREQUENCY - GHz 4.0 4.5 5.0 5.5 6.0 Input VSWR -21.0 2.00 -22.0 1.75 VSWR RF INPUT - dBm Threshold Power @ R = 100 3.0 KEY: +25 °C +85 °C Ohms -55 °C -23.0 1.50 -24.0 1.25 -25.0 1.00 0.0 0.5 1.0 1.5 2.0 -26.0 -27.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 FREQUENCY - GHz 4.0 4.5 5.0 5.5 6.0 Threshold Power @ R = 1 KOhms -13.0 RF INPUT - dBm -14.0 -15.0 -16.0 1 -17.0 -18.0 -19.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 FREQUENCY - GHz 4.0 4.5 5.0 5.5 6.0 Pulse Response @ RTH =100 Ohms Threshold Power @ R = 20 KOhms -2.0 RF INPUT - dBm -3.0 -4.0 -5.0 -6.0 -7.0 -8.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 FREQUENCY - GHz 4.0 4.5 5.0 5.5 6.0 -30 -20 -10 Pulse Response @ RTH = 1 KOhms Pulse Response @ RTH = 20 KOhms Top Trace: TTL Logic Out Bottom Trace: RF Input Time Base: 5.0 µs/div 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] 0 10 Rev. 7/10 0.1 TO 6.0 GHz ANALOG DETECTOR DAQ6101 DAQ6101 Typical Values @ +25 °C Wide Frequency Range. . . . . . . . . . . . . . . . . . . . . . . . . Wide Power Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature Stability . . . . . . . . . . . . . . . . . . . . . . . . . . Flatness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Low VSWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single or Dual Power Supply Cougar Q Package 0.1 to 8.0 GHz –30.0 to +5.0 dBm ± 0.25 dB ± 0.5 dB 1.5:1 DAQ6101 SM-25 for Detectors SPECIFICATIONS* Parameter Typical Frequency (Min.) Guaranteed 0 to 50 °C -55 to +85 °C 0.1-8.0 GHz 0.1-6.0 GHz 0.1-6.0 GHz -30 to +5 dBm -25 to 0 dBm -25 to 0 dBm 1.5:1† 2.0:1† 2.0:1† 120 mV† 90 mV† 90 mV† Power Flatness (Max.) ±0.5 dB^ ±0.75 dB^ ±0.75 dB^ Temperature Stability (Max.) ±0.25 dB† ±0.5 dB† ±0.5 dB† Output Offset Voltage, no RF (Max.) ±0.5 mV ±2.0 mV ±2.0 mV 1 dB Square Law Departure -10 dBm — — Tangential Sensitivity -45 dBm^^ — — Pulse Response, Pin = -15 dBm 1.5 µsec‡ — — Pulse Response, Pin = 0 dBm 3.0 µsec‡ — — Supply Current, no RF 2 +mA, 2 -mA — — Supply Current, Pin = +5 dBm 10 +mA, 2 -mA Input Power Range (Min.) VSWR (Max.) Sensitivity, Vout (Min.) DAS6101 * Measured in a 50-Ohm system at ±5 Vdc, 2 KΩ||50 pF unless otherwise specified. † Pin = –15 dBm. ^ Vout = 100 mV. ^^ 3 dB NF, 1 MHz Bandwidth. ‡ 50% RF to 10 or 90% Video. SMTO-8 Package for Detectors MAXMUM RATINGS DC Voltage (no RF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±18 V Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . +14.0 dBm (±5 Vdc) Operating Case Temperature . . . . . . . . . . . . . . . . . . . . -55 °C to +100 °C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . -65 °C to +125 °C Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . +100 °C Detector Thermal Resistance1 (θjc) . . . . . . . . . . . . . . . +3500 °C/Watt Temperature Rise @ 0 dBm (Tjc) . . . . . . . . . . . . . . . . . +3.5 °C Temperature Rise @ +5 dBm (Tjc) . . . . . . . . . . . . . . . . +35 °C 1 Thermal resistance is based on RF input power. Ratings based on +25 °C. APPLICATION NOTES This unit is DC coupled and employs a RF choke at the input (DC short). If the application calls for the input to sink current there will approximately be an additional 1 mV of output offset voltage for each 3 mA of current. Sink current should be limited to 100 mA max to avoid choke burnout. For higher supply voltages, up to ±15 volts, the positive supply pin must include a series current limiting resistor, Rs = (Vs – 5)/0.01. (e.g.: Vs = 15v, Rs = 1K) Average power detection is obtained at power levels below approximately –13 dBm. For best pulse response both supply pins should be bypassed with an additional 1.0 µF capacitor. The unit contains 0.01 µF internal capacitors. DIMENSIONS ARE IN INCHES [MILLIMETERS] 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] DAQ6101 TYPICAL PERFORMANCE Input Flatness @ Vo = 100 mV KEY: +25 °C +85 °C -55 °C INPUT POWER -13.0 -14.0 -15.0 -16.0 -17.0 0.1 0.6 1.1 1.6 2.1 2.6 3.1 3.6 FREQUENCY - GHz 4.1 4.6 5.1 5.6 6.1 Input Flatness @ Vo = 1.0 V INPUT POWER -1.0 -2.0 Pulse Response @ Pin = 0 dBm -3.0 -4.0 -5.0 0.1 0.6 1.1 1.6 2.1 2.6 3.1 3.6 FREQUENCY - GHz 4.1 4.6 5.1 5.6 6.1 4.1 4.6 5.1 5.6 6.1 Input Flatness @ Vo = 3.0 V INPUT POWER 7.0 6.0 5.0 4.0 3.0 0.1 0.6 1.1 1.6 2.1 2.6 3.1 3.6 FREQUENCY - GHz Input VSWR @ Pin = -15 dBm 2.00 Pulse Response @ Pin = –15 dBm VSWR 1.75 1.50 1.25 1.00 0.1 0.6 1.1 1.6 2.1 2.6 3.1 3.6 FREQUENCY - GHz 4.1 4.6 5.1 5.6 6.1 Transfer Curve @ 1.0 GHz 10.0 OUTPUT VOLTAGE - VOLTS 1.0 0.1 0.01 0.001 0.0001 -50 -40 -30 -20 -10 INPUT POWER - dBm 0 10 20 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] Rev. 7/10 0.1 TO 6.0 GHz ANALOG DETECTOR DAQ6103 DAQ6103 Typical Values @ +25 °C Wide Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . Wide Power Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature Stability . . . . . . . . . . . . . . . . . . . . . . . . . . Flatness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Low VSWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single or Dual Power Supply Cougar Q Package 0.1 to 8.0 GHz –10.0 to +25.0 dBm ± 0.25 dB ± 0.5 dB 1.2:1 DAQ6103 SM-25 for Detectors SPECIFICATIONS* Parameter Typical Frequency (Min.) Input Power Range (Min.) VSWR (Max.) Guaranteed 0 to 50 °C -55 to +85 °C 0.1-8.0 GHz 0.1-6.0 GHz 0.1-6.0 GHz -10 to +25 dBm -5 to +20 dBm -5 to 2+0 dBm 1.2:1† 1.5:1† 1.5:1† 120 mV† 90 mV† 90 mV† Power Flatness (Max.) ±0.5 dB^ ±0.75 dB^ ±0.75 dB^ Temperature Stability (Max.) ±0.25 dB† ±0.5 dB† ±0.5 dB† Output Offset Voltage, no RF (Max.) ±0.5 mV ±2.0 mV ±2.0 mV 1 dB Square Law Departure +10 dBm — — Tangential Sensitivity -25 dBm^^ — — Pulse Response, Pin = +5 dBm 1.5 µsec‡ — — Pulse Response, Pin = +25 dBm 3.0 µsec‡ — — Max Output Voltage Vs-1 Volts — — Supply Current, no RF 2 +mA, 2 -mA — — Supply Current, Pin = +25 dBm 10 +mA, 2 -mA Sensitivity, Vout (Min.) DAS6103 * Measured in a 50-Ohm system at ±5 Vdc, 2 KΩ||50 pF unless otherwise specified. † Pin = +5 dBm. ^ Vout = 100 mV. ^^ 3 dB NF, 1 MHz Bandwidth. ‡ 50% RF to 10 or 90% Video. SMTO-8 Package for Detectors MAXMUM RATINGS DC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . Operating Case Temperature . . . . . . . . . . . . . . . . . . . . Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Detector Thermal Resistance1 (θjc) . . . . . . . . . . . . . . . Temperature Rise @ +20 dBm (Tjc) . . . . . . . . . . . . . . . 1 Thermal ±18 V +27 dBm (±5 Vdc) -55 °C to +100 °C -65 °C to +125 °C +100 °C +3500 °C/Watt +3.5 °C resistance is based on RF input power. Ratings based on +25 °C. ABSOLUTE MAXIMUM RATINGS This unit is DC coupled and employs a RF choke at the input (DC short). If the application calls for the input to sink current there will approximately be an additional 1 mV of output offset voltage for each 3 mA of current. Sink current should be limited to 100 mA max to avoid choke burnout. For higher supply voltages, up to ±15 volts, the positive supply pin must include a series current limiting resistor, Rs = (Vs – 5)/0.01. (e.g.: Vs = 15v, Rs = 1K) Average power detection is obtained at power levels below approximately +7 dBm. For best pulse response the supply pins should be bypassed with an additional 0.1 µF capacitor. The unit contains 0.01 µF internal capacitors. DIMENSIONS ARE IN INCHES [MILLIMETERS] 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] DAQ6103 TYPICAL PERFORMANCE INPUT POWER - dBm Input Flatness @ Vo = 100 mV 6.0 KEY: +25 °C +85 °C -55 °C 5.0 4.0 3.0 2.0 0.1 0.7 1.3 1.9 2.5 3.1 3.7 FREQUENCY - GHz 4.3 4.9 5.5 6.1 Input VSWR @ Pin = +5 dBm 1.50 VSWR 1.25 Pulse Response @ Pin = 0 dBm 1.00 0.75 0.50 0.1 0.7 1.3 1.9 2.5 3.1 3.7 FREQUENCY - GHz 4.3 4.9 5.5 6.1 Transfer Curve Vcc = +10 V 10.0 OUTPUT VOLTAGE - VOLTS 1.0 0.1 0.01 Pulse Response @ Pin = –15 dBm 0.001 0.0001 -30 -20 -10 0 10 INPUT POWER - dBm 20 30 40 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] Rev. 5/10 0.1 TO 6.0 GHz ANALOG DETECTOR DAQ6104 DAQ6104 Typical Values @ +25 °C Wide Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . 0.1 to 8.0 GHz Wide Power Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . –25.0 to +12.0 dBm Temperature Stability . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.5 dB Flatness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.75 dB Low VSWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5:1 Cougar Q Package DAQ6104 SM-25 for Detectors SPECIFICATIONS* Parameter Typical Frequency (Min.) Guaranteed 0 to 50 °C -55 to +85 °C 0.05-7.0 GHz 0.1-6.0 GHz 0.1-6.0 GHz -25 to +12 dBm -20 to +10 dBm -20 to +10 dBm 1.5:1† 1.3:1† 2.0:1† 1.7:1† 2.0:1† 1.7:1† Sensitivity, Vout (Min.) 190 mV† 150 mV† 150 mV† Power Flatness (Max.) ±0.75 dB^ ±1.0 dB^ ±1.0 dB^ ±0.5 dB ±0.75 dB ±0.75 dB Output Offset Voltage, no RF (Max.) ±2.0 mV ±10.0 mV ±10.0 mV 1 dB Square Law Departure -10 dBm — — Tangential Sensitivity -37 dBm^^ — — Pulse Response, Pin = -15 dBm 0.3 µsec‡ 1.0 µsec‡ 1.0 µsec‡ Supply Current, no RF 2 +mA, 2 -mA — — Supply Current, Pin = +5 dBm 10 +mA, 2 -mA Input Power Range (Min.) VSWR (Max.) 0.05-6.0 GHz 0.1-5.0 GHz Temperature Stability (Max.) DAS6104 * Measured in a 50 Ohm system at Vs = ±15 Vdc, and usable down to Vs = ±8 Vdc, 2 KΩ || 50 pF unless otherwise specified. † Pin = –10 dBm. ^ Vout = 1.0 V. ^^ 3 dB NF, 1 MHz Bandwidth. ‡ 50% RF to 10 or 90% Video, Pin= –15 dBm or Pin= 0 dBm SMTO-8 Package for Detectors MAXMUM RATINGS DC Voltage (no RF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . Operating Case Temperature . . . . . . . . . . . . . . . . . . . . Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Detector Thermal Resistance (θjc) . . . . . . . . . . . . . . . . Temperature Rise @ 16 dBm (Tjc) . . . . . . . . . . . . . . . . ±22 V +20.0 dBm -55 °C to +125 °C -65 °C to +150 °C +150 °C +800 °C/Watt +4.5 °C APPLICATION NOTES Average power detection is obtained at power levels below approximately –10 dBm. For best pulse response both supply pins should be bypassed with an additional 1.0 µF capacitor. The unit contains 0.01 µF internal capacitors. DIMENSIONS ARE IN INCHES [MILLIMETERS] 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] DAQ6104 TYPICAL PERFORMANCE INPUT POWER - dBm Input Flatness @ Vo = 100 mV KEY: +25 °C +85 °C -55 °C -12.0 -13.0 -14.0 -15.0 -16.0 0.1 0.6 1.1 2.1 3.1 4.1 5.1 FREQUENCY - GHz 6.1 7.1 7.6 8.1 Input Flatness @ Vo = 1.0 V INPUT POWER - dBm 0.0 -1.0 -2.0 Pulse Response @ Pin = 0 dBm -3.0 -4.0 0.1 0.6 1.1 2.1 3.1 4.1 5.1 FREQUENCY - GHz 6.1 7.1 7.6 8.1 6.1 7.1 7.6 8.1 Input Flatness @ Vo = 3.0 V INPUT POWER - dBm 6.0 5.5 5.0 4.5 4.0 0.1 0.6 1.1 2.1 3.1 4.1 5.1 FREQUENCY - GHz Input VSWR @ Pin = -10 dBm 2.20 2.00 VSWR 1.80 Pulse Response @ Pin = –15 dBm 1.60 Top Trace: Detector Response Bottom Trace: RF Input Time Base: 500 ns/div 1.40 1.20 1.00 0.1 0.6 1.1 2.1 3.1 4.1 5.1 FREQUENCY - GHz 6.1 7.1 7.6 8.1 Transfer Curve @ 1.0 GHz 10.0 OUTPUT VOLTAGE - VOLTS 1.0 0.1 0.01 0.001 0.0001 -40 -30 -20 -10 INPUT POWER - dBm 0 10 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] Rev. 5/10 0.1 TO 6.0 GHz PEAK TO PEAK ANALOG DETECTOR DAQ6116 DAQ6116 Typical Values @ +25 °C Wide Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.05 to 8.0 GHz Wide Power Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –5.0 to +25.0 dBm Temperature Stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.5 dB Flatness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.5 dB Low VSWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5:1 Even Order Harmonics Supression. . . . . . . . . . . . . . . . . . . 40 dB No Power Supply Required / Zero Bias Cougar Q Package or Standard SMTO-8 package DAQ6116 SM-25 for Detectors SPECIFICATIONS* Parameter Typical Guaranteed 0 to 50 °C -55 to +85 °C Frequency (Min.) 0.05-8.0 GHz 0.1-6.0 GHz 0.1-6.0 GHz Input Power Range (Min.) -5 to +25 dBm 0 to +20 dBm 0 to +20 dBm 1.5:1 2.0:1 2.0:1 Sensitivity, Vout (Min.) 180 mV† 120 mV† 90 mV† Power Flatness (Max.) ±0.5 dB ±0.75 dB ±0.75 dB — ±0.5 dB^ ±0.5 dB^ Pulse Response, Pin > +10 dBm 360 µsec‡ 25/500 µsec‡ 25/500 µsec‡ Pulse Response, Pin = 0 to +10 dBm 380 µsec‡ 500/500 µsec‡ 500/500 µsec‡ VSWR (Max.) Temperature Stability (Max.) DAS6116 * Measured in a 50-Ohm system and R load = 1 MOhm unless otherwise specified. † Pin = 0 dBm. ^ Vout = 1.0 V. ‡ Tr/Tf, 50% RF to 90% or 10% Video, Rload = 80 KOhms. SMTO-8 Package for Detectors MAXMUM RATINGS Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . Operating Case Temperature . . . . . . . . . . . . . . . . . . . . Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Detector Thermal Resistance1 (θjc) . . . . . . . . . . . . . . . Temperature Rise @ 20 dBm (Tjc) . . . . . . . . . . . . . . . . Temperature Rise @ 25 dBm (Tjc) . . . . . . . . . . . . . . . . 1 Thermal +25.0 dBm -55 °C to +150 °C -65 °C to +150 °C +125 °C +1000 °C/Watt +4 °C +68 °C resistance is based on total power dissipation. Ratings based on +25 °C. APPLICATION NOTES DAQ6116 is configured using two anti-parallel connected schottky diodes to form an unbiased peak to peak microwave detector with a differential output voltage. The harmonic distortion reflected back to the system can be significantly lower than single ended design because all even order harmonics are suppressed, typically > 40 dB. The output voltage (differential) is a closer representation of the true rms power of modulated or distorted signals because both positive and negative waveform peaks are detected. The DAQ6116 is intended for higher level detection applications (> 0 dBm) requiring good temperature stability and harmonic suppression. DIMENSIONS ARE IN INCHES [MILLIMETERS] 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] DAQ6116 TYPICAL PERFORMANCE INPUT POWER - dBm Power Flatness @ Vo = 100 + KEY: +25 °C +85 °C mV -55 °C TIME BASE: 2 ms/div -1.0 -3.0 -5.0 -7.0 -9.0 0.0 0.5 1.0 2.0 3.0 3.0 4.0 5.0 4.0 5.0 6.0 FREQUENCY - GHz 7.0 6.0 7.5 7.0 8.0 7.5 7.0 6.0 7.5 7.0 8.0 7.5 8.0 INPUT POWER - dBm Power Flatness @ Vo = 1.0 V 12.0 12.0 Pulse Response @ Pin = +20 dBm, R load = 80KOhm Pulse Response @ Pin = +20 dBm, R load = 1 MOhm Pulse Response @ Pin = +10 dBm, R load = 80KOhm Pulse Response @ Pin = +10 dBm, R load = 1 MOhm 11.0 10.0 9.0 8.0 0.0 0.5 1.0 2.0 3.0 F 3.0 4.0 5.0 4.0 5.0 6.0 FREQUENCY - GHz 8.0 I INPUT POWER - dBm Power Flatness @ Vo = 3.0 V 21.0 20.0 19.0 TIME BASE: 500 µs/div 18.0 17.0 0.0 0.5 1.0 2.0 3.0 3.0 4.0 5.0 4.0 5.0 6.0 FREQUENCY - GHz 7.0 6.0 7.5 7.0 8.0 7.5 8.0 Input VSWR @ Pin = 0 dBm 2.00 1.75 1.75 1.50 1.25 1.25 1.00 1.00 0.0 0.5 1.0 2.0 3.0 3.0 4.0 5.0 4.0 5.0 6.0 FREQUENCY - GHz 7.0 6.0 7.5 7.0 8.0 7.5 Top Trace: Video out +, R load = 80 KOhm Bottom Trace: RF input 8.0 Transfer Curve @ 1.0 GHz 5.0 1.0 4.0 0.1 + 0.01 0 ° LOG SCALE KEY: +25 °C +85 °C -20 °C -55 °C 0 °C 0.001 0.0001 -10 Top Trace: Video out –, R load = 80 KOhm Bottom Trace: RF input 3.0 3.0 2.0 2.0 LINEAR SCALE KEY: +25 °C +85 °C -20 °C -55 °C 0 ° 0 °C O OUTPUT VOLTAGE - VOLTS Transfer Curve @ 1.0 GHz 10.0 OUTPUT VOLTAGE - VOLTS 1.50 VSWR 2.00 1.0 -5 50 5 10 15 10 15 20 INPUT POWER - dBm 20 25 25 0.0 -10 -5 -5 0 5 50 10 INPUT POWER - dBm 10 15 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] 15 20 20 25 25 Rev. 7/10 0.1 TO 8.0 GHz THRESHOLD DETECTOR DTS8003 DTS8003 Typical Values @ +25 °C Wide Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . 0.1 to 8.0 GHz Wide Power Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . -10.0 to +15.0 dBm Temperature Stability . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.50 dB Power Flatness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.50 dB Standard Size TO-8 or Surface Mount Package External Adjustable Threshold Level, Fast Response Time, Low Drift, Insensitive Threshold Level to Applied Voltage DTC8003 TO-8 Package for Detectors SPECIFICATIONS* Parameter Typical Frequency (Min.) Guaranteed 0 to 50 °C -40 to +85 °C 0.1-9.0 GHz 0.1-8.0 GHz 0.1-8.0 GHz -10 to +15 dBm* -5 to +15 dBm* -5 to +15 dBm* 1.2:1 1.7:1‡ 1.7:1‡ Power Flatness (Max.) ±0.5 dB ±0.75‡ dB ±0.75‡ dB Threshold Temperature Stability (Max.) ±0.25 dB ±0.5 dB ±0.5 dB Threshold Hysteresis (Max.) ±0.2 dB ±0.5 dB ±0.5 dB Pulse Response (Max.) 50^ µsec 100^ µsec 100^ µsec 1 1 1 Output Voltage Hi @ 5mA source 4.4 Volts 3.5 Volts 3.5 Volts Output Voltage Lo @ 5mA sink 0.1 Volts 0.25 Volts 0.25 Volts 1.0 mA 2.0 mA 2.0 mA Input Power Range (Min.) VSWR (Max.) Logic: Pin > Pth Supply Current (Max.) DTS8003 * Measured in a 50 Ohm system at Vs=+5.0 Vdc. RTH=100 ohm to 100 KOhm unless otherwise specified. ^ 50% RF to 10 or 90% Video Response time for input change 3 dB above Pth. ‡ For TO-8 model (DTC8003) VSWR degraded to 2.0:1 above 4 GHz and flatness degraded to ±1.0 dB above 7 GHz. SMTO-8 Package for Detectors MAXMUM RATINGS DC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . Operating Case Temperature . . . . . . . . . . . . . . . . . . . . Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Detector Thermal Resistance1 (θjc) . . . . . . . . . . . . . . . Temperature Rise @ 0 dBm . . . . . . . . . . . . . . . . . . . . . 1 Thermal +15 V +20.0 dBm -40 °C to +125 °C -65 °C to +150 °C +125 °C +3500 °C/Watt +3.5 °C resistance is based on RF input power. Ratings based on +25 °C. APPLICATION NOTES This unit is DC coupled and employs a RF choke at the input (DC short). DO NOT bypass the Threshold Control pin. Capacitance greater than 50pF may cause instabilities. Keep the threshold programming resistor or circuit close to this pin. Average power detection is obtained at power levels below approximately +7 dBm. The output of this unit is derived from an op-amp, not a true logic device. Connect external threshold resistor from Rcntl port to ground. DIMENSIONS ARE IN INCHES [MILLIMETERS] 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] DTS8003 R TYPICAL PERFORMANCE Input VSWR @ Pin = +10 dBm -1.0 1.6 -2.0 1.5 -3.0 1.4 VSWR RF INPUT - dBm Threshold Power @ R = 100 KEY: +25 °C +85 °C Ohms -40 °C -4.0 1.3 1.2 -5.0 1.1 -6.0 0.1 0.5 1.0 1.5 2.0 3.0 4.0 5.0 6.0 7.0 FREQUENCY - GHz 8.0 8.5 9.0 9.5 10.0 1.0 0.1 1.0 Threshold Power @ R = 1 KOhms 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 FREQUENCY - GHz 6.0 6.5 7.0 7.5 8.0 1 6.0 5.0 Hysterisis Vs Input Power @ 25° C 0 -0.1 4.0 + 3.0 2.0 0.1 0.5 1.0 1.5 2.0 3.0 4.0 5.0 6.0 7.0 FREQUENCY - GHz 8.0 8.5 9.0 9.5 10.0 HYSTERISIS - dB RF INPUT - dBm 7.0 -0.2 -0.3 -0.4 -0.5 Threshold Power @ R = 20 KOhms -0.6 RF INPUT - dBm 16.0 -20 -15 -10 -5 0 5 INPUT POWER - dBm 10 15.0 14.0 13.0 12.0 11.0 0.1 0.5 1.0 1.5 2.0 3.0 4.0 5.0 6.0 7.0 FREQUENCY - GHz 8.0 8.5 9.0 9.5 10.0 Pulse Response @ RTH =100 Ohms R Pulse Response @ RTH = 1 KOhms Pulse Response @ RTH = 20 KOhms Top Trace: TTL Logic Out Bottom Trace: RF Input Time Base: 10.0 µs/div 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] 15 20 Rev. 7/10 0.5 TO 8.0 GHz ULTRA HI-SPEED THRESHOLD DETECTOR DTS8031 DTS8031 Typical Values @ +25 °C Wide Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . Super-fast Pulse Response . . . . . . . . . . . . . . . . . . . . . Temperature Stability . . . . . . . . . . . . . . . . . . . . . . . . . . Power Flatness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard Size SMTO-8 Surface Mount Package External Adjustable Threshold Level, Low Drift 0.5 to 8.0 GHz 5-10 ηs ± 0.50 dB ± 0.50 dB DTS8031 SMTO-8 Threshold Detector Package SMTO-8 Package for Detectors SPECIFICATIONS* Parameter Typical Guaranteed 0 to 50 °C -40 to +85 °C Frequency (Min.) 0.5-10.0 GHz 0.5-8.0 GHz 0.5-8.0 GHz Input Power Range (Min.) -15 to -3 dBm* -15 to -5 dBm* -15 to -5 dBm* 1.5:1 2.0:1‡ 2.0:1‡ Power Flatness (Max.) ±0.5 dB ±0.75 dB ±0.75 dB Threshold Temperature Stability (Max.) ±0.25 dB ±0.5 dB ±0.5 dB Threshold Hysteresis (Max.) ±0.2 dB ±1.0 dB ±1.5 dB Pulse Response (Max.) At 50 Ω˙˙ 8 pF load 5 ηsec 10^ ηsec 12^ ηsec 1 1 1 Output Voltage Hi @ 5mA source 4.4 Volts 3.5 Volts 3.5 Volts Output Voltage Lo @ 5mA sink 0.27 Volts 0.5 Volts 0.5 Volts 7.0 mA 12.0 mA 15.0 mA VSWR (Max.) Logic: Pin > Pth Supply Current (Max.) * Measured in a 50 Ohm system at Vs=+5.0 Vdc. RTH=2 Ohm to 2 KOhm unless otherwise specified. ^ 50% RF to 10 or 90% Video Response time for input change 3 dB above Pth. ‡ Pin=<–15 dBm Teledyne Cougar • 408-522-3838 • 408-522-3839 fax www.teledyne-cougar.com • [email protected] MAXMUM RATINGS DC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . Operating Case Temperature . . . . . . . . . . . . . . . . . . . . Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Detector Thermal Resistance1 (θjc) . . . . . . . . . . . . . . . Temperature Rise @ 0 dBm . . . . . . . . . . . . . . . . . . . . . 1 Thermal +6 V +14.0 dBm -40 °C to +125 °C -65 °C to +150 °C +125 °C +3500 °C/Watt +3.5 °C resistance is based on RF input power. Ratings based on +25 °C. APPLICATION NOTES RF input is AC coupled (DC block). DTS8031 contains a plastic packaged IC-Ultra Hi-speed comparator. DTS8031 provides maximum performance with minimum output capacitance. A heavy capacitive load slows down the TTL output response. Connect external threshold resistor from Rcntl port to ground. DIMENSIONS ARE IN INCHES [MILLIMETERS] 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] Threshold Power @ R = 20 Ohms HYST -40 °C DTS8031 -1.5 -12.0 Typical Performance -2.0 -9 -8 -7 INPUT POWER - dBm -6 -5 -4 2.0 3.0 3.5 4.0 4.5 5.0 5.5 6.0 FREQUENCY - GHz TYPICAL PERFORMANCE 0.5 7.0 8.0 9.0 10.0 6.5 Threshold Power @ R = 500 Ohms KEY: Threshold Power @ R = 20 Ohms -2.0 -10.0 +25 °C +85 °C -40 °C 0.0 -0.5 Control Resistance vs. Threshold Power (dBm) 10000 -1.0 -3.0 -11.0 RF INPUT - dBm -1.5 -4.0 -12.0 -5.0 -13.0 -6.0 -14.0 0.5 1.0 2.0 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 8.0 9.0 10.0 2.0 -15.0 FREQUENCY - GHz 0.5 1.0 2.0 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 8.0 9.0 10.0 Input VSWR @ Pin = -12 dBm- GHz FREQUENCY 2.0 1.8 -1.0 Threshold Power @ R = 500 Ohms 1000 -2.0 -12 -11 4.0 2.0 Input VSWR @ Pin = -12 dBm 3.6 1.8 CONTROL RESISTANCE - Ohm 1.0 -5.0 0.1 1.0 2.0 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 8.0 9.0 10.0 -6.0 FREQUENCY - GHz 0.5 1.0 2.0 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 8.0 9.0 10.0 Input VSWR @ Pin = -4 dBm - GHz 2.0 FREQUENCY 4.4 -8 -7 INPUT POWER - dBm -6 -5 -4 -3 Control Resistance vs. Threshold Power (dBm) -15 -14 1.4 -3.0 1.2 -4.0 -9 10 1 10000 -18 -16 RF INPUT - dBm -10 100 1.6 -2.0 -13 -12 -11 -10 -9 -8 -7 -6 THRESHOLD POWER - dBm -5 -4 -3 1000 100 10 1 VSWR 3.2 1.6 -18 -16 2.8 1.4 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 THRESHOLD POWER - dBm -5 2.4 1.2 2.0 1.0 0.1 0.1 1.0 1.0 2.0 2.0 3.0 3.0 3.5 3.5 4.0 4.0 4.5 4.5 5.0 5.0 5.5 5.5 6.0 6.0 6.5 6.5 7.0 7.0 8.0 8.0 9.0 10.0 9.0 10.0 FREQUENCY - GHz FREQUENCY - GHz Input VSWR @ Pin = -4 dBm 4.4 4.0 VSWR -3 DTS8031 1.0 HYSTERISIS - dB -1.0 RF INPUT - dBm -10 Hysterisis Vs Threshold Power -14.0 0.5 1.0 VSWR -12 -11 -13.0 -15.0 VSWR -1.0 -11.0 CONTROL RESISTANCE - Ohm RF INPUT - dBm -10.0 3.6 3.2 2.8 Pulse Response @ RTH = 20 Ohms / Load = 50 Ohms 2.4 2.0 0.1 1.0 2.0 3.0 3.5 4.0 4.5 5.0 5.5 6.0 FREQUENCY - GHz 6.5 7.0 8.0 9.0 10.0 Pulse Response @ RTH = 500 Ohms / Load = 50 Ohms Top Trace: TTL Logic Out Bottom Trace: RF Input Time Base: 5.0 ηs/div 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] -4 -3 Rev. 7/10 0.5 TO 8.0 GHz HIGH-SPEED ANALOG DETECTOR DAS8121 DAS8121 Typical Values @ +25 °C Wide Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . Wide Power Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature Stability . . . . . . . . . . . . . . . . . . . . . . . . . . Power Flatness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Low VSWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Super fast pulse response . . . . . . . . . . . . . . . . . . . . . . Standard SMTO-8 Package Fast Response Time, Low Drift 0.5 to 10.0 GHz -30.0 to +5.0 dBm ± 0.5 dB ± 0.5 dB 1.5:1 15-20 ηs DAS8121 SMTO-8 Analog Detector Package SMTO-8 for Detectors SPECIFICATIONS* Parameter Typical Frequency (Min.) Input Power Range (Min.) VSWR (Max.) Guaranteed 0 to 50 °C -40 to +85°C 0.5-10.0 GHz 0.5-8.0 GHz 0.5-8.0 GHz -30 to +5 dBm -25 to 0 dBm -25 to 0 dBm 1.5:1 1.5:1 1.8:1 2.0:1 1.8:1 2.0:1 1-6 GHz 0.5-8 GHz Sensitivity, Vout (Min.) 140 mV† 90 mV† 90 mV† Power Flatness (Max.) ±0.5 dB ±0.75 dB ±0.75 dB Temperature Stability (Max.) ±0.4 dB ±0.5 dB ±0.5 dB Pulse Response, Pin = -15 dBm 15 ηsec‡ 35/50 ηsec‡ 35/50 ηsec‡ Pulse Response, Pin = 0 dBm 22 ηsec‡ 50/70 ηsec‡ 50/70 ηsec‡ Supply Current, no RF (Max.) 9 mA 12 mA 15 mA Supply Current, Pin = 5 dBm (Max.) 15 mA 22 mA 25 mA 2 mV 10 mV 10 mV -10 dBm — — Output Offset Voltage, no RF (Max.) 1 dB Square Law Departure *Measured in a 50 Ohm system at ±5.0 Vdc unless otherwise specified. †Pin = –15 dBm. ‡Total response time, Tr/Tf: 50% RF to 90 or 10% Video. 50 Ohm || 8pF output load. Teledyne Cougar • 408-522-3838 • 408-522-3839 fax www.teledyne-cougar.com • [email protected] MAXMUM RATINGS DC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . Operating Case Temperature . . . . . . . . . . . . . . . . . . . . Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Detector Thermal Resistance1 (θjc) . . . . . . . . . . . . . . . Temperature Rise @ 0 dBm (Tjc) . . . . . . . . . . . . . . . . . Temperature Rise @ +5 dBm (Tjc) . . . . . . . . . . . . . . . . 1 Thermal ±6.0 V +14.0 dBm -40 °C to +95 °C -65 °C to +125 °C +125 °C +3500 °C/Watt +3.5 °C +35 °C resistance is based on RF input power. Ratings based on +25 °C. APPLICATION NOTES Average power detection is obtained at power levels below approximately -13dBm. RF input is AC coupled (DC block). DAS8121 contains a plastic packaged IC. DAS8121 provides maximum video performance with no output load capacitance. However, the detector is capable of driving capacitive loads up to 100 pF without oscillations. Load capacitance above that specified may produce pulse overshoot and ringing. DIMENSIONS ARE IN INCHES [MILLIMETERS] 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] 0.0 2.50 DAQ4001DAQ4001 DAQ4001 Typical Performance 0.5 1.0 1.5 2.0 FREQUENCY - GHz 3.0 4.0 5.0 6.0 7.0 FREQUENCY - GHz 8.0 8.5 9.0 9.5 10.0 Input VSWR @ Pin = -15 dBm Input VSWR @ Pin = -15 dBm 2.50 2.25 Typical Performance Typical Performance VSWR VSWR 2.25 2.00 DAS8121 2.00 1.75 1.75 1.50 1.50 1.25 -15.0 -16.0 -17.0 10.0 10.0 1.0 1.0 1.5 1.0 1.5 2.0 3.0 4.0 5.0 6.0 7.0 8.0 2.0 3.0FREQUENCY 4.0 5.0 6.0 - GHz7.0 8.0 FREQUENCY - GHz 8.5 9.0 8.5 9.0 9.5 10.0 9.5 10.0 Input Flatness @ Vo = 1.0 V -18.0 0.0 0.5 1.0 1.5 2.0 Input Flatness @ Vo = 1.0 V -3.0 -3.0 3.0-4.0 5.0 6.0 7.0 8.0 8.5 9.0 9.5 10.0 -4.04.0 FREQUENCY - GHz -5.0 -5.0 -6.0 -6.0 -7.0 -7.00.0 0.5 1.0 1.5 2.0 3.0 4.0 5.0 6.0 7.0 8.0 8.5 9.0 0.0 0.5 1.0 1.5 2.0 3.0FREQUENCY 4.0 5.0 6.0 - GHz7.0 8.0 8.5 9.0 FREQUENCY - GHz INPUTPOWER POWER- dBm - dBm INPUT -3.0 -4.0 9.5 10.0 9.5 10.0 -6.0 -7.0 0.0 0.5 1.0 1.5 2.0 Input Flatness @ Vo = 3.0 V 4.0 4.0 3.0 3.0 2.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 8.5 9.0 9.5 10.0 1.0 FREQUENCY - GHz 1.0 0.0 0.00.0 0.5 1.0 1.5 2.0 3.0 4.0 5.0 6.0 7.0 8.0 8.5 9.0 0.0 0.5 1.0 1.5 2.0 3.0FREQUENCY 4.0 5.0 6.0 - GHz7.0 8.0 8.5 9.0 FREQUENCY - GHz 1.0 0.0 9.5 10.0 9.5 10.0 Input VSWR @ Pin = -15 dBm 2.50 2.50 2.25 2.25 2.00 2.00 1.75 1.75 1.50 3.01.504.0 5.0 6.0 7.0 8.0 8.5 9.0 9.5 10.0 FREQUENCY - GHz 1.25 1.25 1.00 1.000.0 0.5 1.0 1.5 2.0 3.0 4.0 5.0 6.0 7.0 8.0 8.5 9.0 0.0 0.5 1.0 1.5 2.0 3.0FREQUENCY 4.0 5.0 6.0 - GHz7.0 8.0 8.5 9.0 FREQUENCY - GHz 0.5 1.0 1.5 2.0 10.0 10.0 1.75 1.50 1.25 1.00 0.0 0.5 1.0 1.5 2.0 OUTPUTVOLTAGE VOLTAGE- VOLTS - VOLTS OUTPUT VSWR 2.00 1.0 1.0 Transfer Curve @ 1.0 GHz Transfer Curve @ 1.0 GHz 0.1 0.1 0.01 8.0 8.5 9.0 9.5 10.0 Transfer Curve 0.001 @ 0.0011.0 GHz 5.0 5.0 4.0 4.0 -32 -24 -16 -8 -24 -16 -8 INPUT POWER - dBm INPUT POWER - dBm 0 0 Transfer Curve @ 1.0 GHz Transfer Curve @ 1.0 GHz LINEAR SCALE LINEAR SCALE KEY: +25 KEY: °C +25 °C °C +85 +85 °C -55 °C -55 °C 0.01 0.001 Top Trace: 1.0 Detector Response 1.0 Bottom Trace: RF Input -24 -16 -8 0 Time 100 ηs/div 0.0 INPUTBase: POWER - dBm -32 -32 Transfer Curve @ 1.0 GHz 0.0001 -40 8 -24 -16 -8 -24 -16 -8 INPUT POWER - dBm INPUT POWER - dBm 0 0 3.0 LOG SCALE KEY: LOG SCALE +25 KEY: °C +85 °C +25 °C -55 °C +85 °C 1.0 -55 °C -32 -32 -24 INPUT -24 INPUT -16 -8 POWER - dBm -16 -8 POWER - dBm 0 8 0 8 LINEAR SCALE KEY: LINEAR SCALE +25 KEY: °C +85 °C +25 °C -55 °C +85 °C -55 °C 1.0 -32 -32 -24 -16 -8 INPUT POWER - dBm -24 -16 -8 INPUT POWER - dBm 0 8 0 8 0 0 8 8 Transfer Curve @ 3.0 GHz Transfer Curve @ 3.0 GHz LOG SCALE LOG SCALE KEY: +25 KEY: °C +25 °C +85 °C +85 °C -55 °C -55 °C 0.01 0.01 0.0001 LOG SCALE 0.0001-40 -32 -24 -16 -8 KEY:-40 -32 -24 -16 -8 INPUT POWER - dBm INPUT POWER - dBm +25 °C Transfer Curve @ 3.0 GHz +85 °C5.0 Transfer Curve @ 3.0 GHz -55 °C5.0 LINEAR SCALE LINEAR SCALE KEY: +25 KEY: °C +25 °C °C +85 +85 °C -55 °C -55 °C 3.0 3.0 2.0 2.0 1.0 1.0 -24 -16 -8 INPUT POWER - dBm -32 -32 -24 -16 -8 -24 -16 -8 INPUT POWER - dBm INPUT POWER - dBm Transfer Curve @ 3.0 GHz 0 8 0 0 5.0 LINEAR SCALE • [email protected] • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com 4.0 TS LINEAR SCALE 650-691-9800 KEY: +25 °C +85 °C KEY: +25 °C +85 °C -5 0.01 0.01 0.001 5.0 T T 5.0 LIN 4.0 3.0 3.0 2.0 2.0 1.0 1.0 0.1 0.1 -32 L +2 +8 +2 -5 +8 0.1 4.0 2.0 4.0 4.0 0.1 L 0.0001 -40 0.0001 -40 Transfer Curve @ 1.0 GHz Transfer Curve @ 1.0 GHz 2.0 1.0 1.0 1.0 Tr Tr 0.001 3.0 0.0 0.0-40 -40 8 8 5.0 TS 4.0 0.1 Pulse Response @ Pin = -15 dBm 2.0 0.0-40 -40 8 8 1.0 3.0 3.0 Pulse Response @ Pin = 0 dBm 2.0 0.001 -32 -32 OUTPUT VOLTAGE - VOLTS 0.0001 0.0001-40 -40 OUTPUTVOLTAGE VOLTAGE- VOLTS - VOLTS OUTPUT OUTPUT VOLTAGE - VOLTS LOG SCALE KEY: +25 °C +85 °C -55 °C 0.01 4.0 10.0 10.0 0.1 0.0001 -40 10.0 0.001 Transfer Curve @ 3.0 GHz 0.001 10.0 1.0 9.5 10.0 Transfer Curve @ 1.0 GHz Transfer Curve @ 1.0 GHz 0.001 10.0 10.0 LOG SCALE LOG SCALE KEY: +25 KEY: °C +25 °C +85 °C +85 °C -55 °C -55 °C 3.00.014.0 5.0 6.0 7.0 FREQUENCY - GHz 9.5 10.0 9.0 9.5 10.0 9.5 10.0 OUTPUTVOLTAGE VOLTAGE- VOLTS - VOLTS OUTPUT 2.25 9.0 8.5 0.01 0.0 -40 0.0 -40 Input VSWR @ Pin = -15 dBm 2.50 8.5 8.0 1.0 OUTPUTVOLTAGE VOLTAGE- VOLTS - VOLTS OUTPUT 0.0 8.0 0.01 4.0 VSWR VSWR INPUT POWER - dBm 2.0 3.0 4.0 5.0 6.0 7.0 - GHz7.0 3.0FREQUENCY 4.0 5.0 6.0 0.1 5.0 Input VSWR @ Pin = -15 dBm 3.0 0.1 5.0 Input Flatness @ Vo = 3.0 V 4.0 1.0 0.0001 -40 0.0001 -40 Input Flatness @ Vo = 3.0 V -5.0 2.0 0.001 INPUTPOWER POWER- dBm - dBm INPUT INPUT POWER - dBm Input Flatness @ Vo = 1.0 V OUTPUT VOLTAGE - VOLTS OUTPUT VOLTAGE - VOLTS INPUT POWER - dBm -14.0 2.0 1.5 FREQUENCY - GHz +85 °C -55 °C Input Flatness @ Vo = 100 mV 1.5 1.0 OUTPUT VOLTAGE - VOLTS OUTPUT VOLTAGE - VOLTS -14.0 -14.0 -15.0 -15.0 -16.0 -16.0 -17.0 -17.0 -18.0 -18.00.0 0.5 0.0 0.5 1.0 OUTPUT VOLTAGE - VOLTS OUTPUT VOLTAGE - VOLTS Input Flatness @ Vo = 100 mV Input FlatnessKEY: @ Vo+25 = 100 °C mV 1.25 1.00 0.0 0.5 1.00 0.0 0.5 KEY: +25 °C KEY: +85 +25 °C °C +85 °C -55 °C -55 °C OUTPUT VOLTAGE - VOLTS OUTPUT VOLTAGE - VOLTS INPUTPOWER POWER- dBm - dBm INPUT TYPICAL PERFORMANCE 8 8 0.0 -40 0.0 -40 LIN +2 +8 + +- Rev. 7/10 0.05 TO 10.0 GHz BROADBAND ANALOG DETECTOR DAQ10501 DAQ10501 Typical Values @ +25 °C Wide Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . Wide Power Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature Stability . . . . . . . . . . . . . . . . . . . . . . . . . . Flatness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single or Dual Power Supply Cougar Q Package 0.05 to 12.0 GHz -30.0 to +5.0 dBm ± 0.25 dB ± 0.50 dB 0.25 Inch SMTO-8 DAQ10501 Analog Detector Package SM-25 for Detectors SPECIFICATIONS* Parameter Typical Frequency (Min.) Guaranteed 0 to 50 °C -55 to +85 °C 0.05-12.0 GHz 0.05-10.0 GHz 0.05-10.0 GHz -30 to 5 dBm -25 to 0 dBm -25 to 0 dBm 1.5:1† 2.0:1† 2.0:1† Sensitivity, Vout (Min.) 120 mV† 90 mV† 90 mV† Power Flatness (Max.) 0.05-8.0 GHz 0.05-10.0 GHz ±0.5 dB^ ±0.75 dB^ ±0.75 dB^ ±1.0 dB^ ±0.75 dB^ ±1.0 dB^ Temperature Stability (Max.) Input Power Range (Min.) VSWR (Max.) ±0.25 dB† ±0.5 dB† ±0.5 dB† Output Offset Voltage, no RF (Max.) ±0.1 dB ±0.5 dB ±0.5 dB 1 dB Square Law Departure -10 dBm — — Tangential Sensitivity -45 dBm^^ — — Pulse Response, Pin = -15 dBm 1.5 µsec‡ 3.0 µsec‡ 3.0 µsec‡ 5.0 µsec‡ Pulse Response, Pin = 0 dBm 3.0 µsec‡ 5.0 µsec‡ Supply Current, no RF 2 +mA, 2 -mA — — Supply Current, Pin = +5 dBm 10 +mA, 2 -mA — — * Measured in a 50-Ohm system at ±5.0 Vdc, 2 KΩ||50 pF unless otherwise specified. † Pin = –15 dBm. ^ Vout = 100 mV. ^^ 3 dB NF, 1 MHz Bandwidth. ‡ 50% RF to 10 or 90% Video. Teledyne Cougar • 408-522-3838 • 408-522-3839 fax www.teledyne-cougar.com • [email protected] MAXMUM RATINGS DC Voltage (no RF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±18 V Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . +14.0 dBm (±5 Vdc) Operating Case Temperature . . . . . . . . . . . . . . . . . . . . -55 °C to +100 °C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . -65 °C to +125 °C Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . +100 °C Detector Thermal Resistance1 (θjc) . . . . . . . . . . . . . . . +3500 °C/Watt Temperature Rise @ 0 dBm (Tjc) . . . . . . . . . . . . . . . . . +3.5 °C Temperature Rise @ +5 dBm (Tjc) . . . . . . . . . . . . . . . . +35 °C 1 Thermal resistance is based on RF input power. Ratings based on +25 °C. APPLICATION NOTES This unit is DC coupled and employs a RF choke at the input (DC short). If the application calls for the input to sink current there will approximately be an additional 1 mV of output offset voltage for each 3 mA of current. Sink current should be limited to 100 mA max to avoid choke burnout. For higher supply voltages, up to ±15 volts, the positive supply pin must include a series current limiting resistor, Rs = (Vs – 5)/0.01. (e.g.: Vs = 15v, Rs = 1K) Average power detection is obtained at power levels below approximately –13 dBm. For best pulse response both supply pins should be bypassed with an additional 1.0 µF capacitor. The unit contains 0.01 µF internal capacitors. DIMENSIONS ARE IN INCHES [MILLIMETERS] 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] DAQ10501 Typical Performance DAQ10501 TYPICAL PERFORMANCE INPUT POWER - dBm Input Flatness @ Vo = 100 mV KEY: +25 °C +85 °C -55 °C -13.0 -14.0 -15.0 -16.0 -17.0 0.05 0.1 0.5 1.0 2.0 3.0 5.0 7.0 FREQUENCY - GHz 8.0 8.5 9.0 9.5 10.0 INPUT POWER - dBm Input Flatness @ Vo = 1.0 V -1.0 -2.0 -3.0 Pulse Response @ PIN = 0 dBm -4.0 -5.0 0.05 0.1 0.5 1.0 2.0 3.0 5.0 7.0 FREQUENCY - GHz 8.0 8.5 9.0 9.5 10.0 8.0 8.5 9.0 9.5 10.0 INPUT POWER - dBm Input Flatness @ Vo = 3.0 V 7.0 6.0 5.0 4.0 3.0 0.05 0.1 0.5 1.0 2.0 3.0 5.0 7.0 FREQUENCY - GHz Input VSWR @ Pin = -15 dBm 2.00 VSWR 1.75 Pulse Response @ PIN = –15 dBm 1.50 1.25 1.00 0.05 0.1 0.5 1.0 2.0 3.0 5.0 7.0 FREQUENCY - GHz 8.0 8.5 9.0 9.5 10.0 Transfer Curve @ 6.0 GHz 10.0 OUTPUT VOLTAGE - VOLTS 1.0 0.1 0.01 0.001 0.0001 -40 -30 -20 -10 INPUT POWER - dBm 0 10 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] Rev. 7/10 0.1 TO 18.0 GHz ULTRA BROADBAND ANALOG DETECTOR DACP18001 DACP18001 Typical Values @ +25 °C Wide Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . Wide Power Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature Stability . . . . . . . . . . . . . . . . . . . . . . . . . . Flatness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . High Frequency CougarPak® Package 0.1 to 18.0 GHz -30.0 to +5.0 dBm ± 0.25 dB ± 0.50 dB DACP18001 High Frequency CougarPak™ (SMA) for Analog Detectors High Frequency CougarPak Package (single-stage) for Detectors ® SPECIFICATIONS* Parameter Typical Guaranteed 0 to 50 °C -55 to +85 °C Frequency (Min.) 0.1-18.0 GHz 0.1-18.0 GHz 0.1-18.0 GHz Input Power Range (Min.) -30 to +5 dBm -25 to 0 dBm -25 to 0 dBm 1.5:1** 2.0:1** 2.0:1** 140 mV† 100 mV† 100 mV† Power Flatness (Max.) ±0.5 dB^ ±1.0 dB^ ±1.0 dB^ Temperature Stability (Max.) ±0.25 dB ±0.5 dB ±0.5 dB Output Offset Voltage, no RF (Max.) ±0.3 mV ±1.5 mV ±2.0 mV — VSWR (Max.) Sensitivity, Vout (Min.) 1 dB Square Law Departure -10 dBm — Tangential Sensitivity -45 dBm^^ — — Pulse Response, Pin = -15 dBm 0.3 µsec‡ 0.5 µsec‡ 0.7 µsec‡ Pulse Response, Pin = 0 dBm 0.5 µsec‡ 0.7 µsec‡ 1.0 µsec‡ Supply Current, no RF +3 mA, -3 mA +4 mA, -4 mA +4 mA, -4 mA Supply Current, Pin = +5 dBm +10 mA, -4 mA +11 mA, -5 mA +11 mA, -5 mA * Measured in a 50 Ohm system at ±5.0 Vdc, 1 MΩ||8 pF unless otherwise specified. † Pin = –15 dBm. ^ Vout = 100 mV. ^^ 3 dB NF, 1 MHz Bandwidth. ‡ 50% RF to 10 or 90% Video. ** Pin < –15 dBm. MAXMUM RATINGS Teledyne Cougar • 408-522-3838 • 408-522-3839 fax www.teledyne-cougar.com • [email protected] DC Voltage (no RF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±22 V Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . +14.0 dBm (±5 Vdc) Operating Case Temperature . . . . . . . . . . . . . . . . . . . . -55 °C to +100 °C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . -65 °C to +150 °C Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . +100 °C Detector Thermal Resistance1 (θjc) . . . . . . . . . . . . . . . +3500 °C/Watt Temperature Rise @ 0 dBm (Tjc) . . . . . . . . . . . . . . . . . +3.5 °C Temperature Rise @ +5 dBm (Tjc) . . . . . . . . . . . . . . . . +35 °C 1 Thermal resistance is based on RF input power. Ratings based on +25 °C. APPLICATION NOTES This unit is DC coupled and employs a RF choke at the input (DC short). If the application calls for the input to sink current there will approximately be an additional 1 mV of output offset voltage for each 3 mA of current. Sink current should be limited to 250 mA max to avoid choke burnout. For higher supply voltages, up to ±22 volts, the positive supply pin must include a series current limiting resistor Rs = (Vs – 5)/0.01. (e.g.: Vs = 15v, Rs = 1K) Average power detection is obtained at power levels below approximately –13 dBm. For best pulse response both supply pins should be bypassed with an additional 1.0 µF capacitor. The unit contains 0.01 µF internal capacitors. DIMENSIONS ARE IN INCHES [MILLIMETERS] 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] INPUT P DACP18001 -19 -20 0.1 Typical Performance 0.5 1 2 3 4 8 12 FREQUENCY - GHz 16 17 17.5 18 DACP18001 INPUT POWER - dBm Input Flatness @ Vo = 1.0 V -4 -5 -6 TYPICAL PERFORMANCE -7 -8 0.1 Typical Performance -18 -19 1 2 3 4 8 12 16 FREQUENCY - GHzKEY: +25 °C INPUT POWER - dBm -4 +85 °C -55 °C -18 -20 0.1 0.5 INPUT POWER - dBm -4 0.5 1 2 3 4 8 12 FREQUENCY - GHz 1 2 3 4 16 8 17 12 17.5 18 16 17 17.5 18 17.5 18 17.5 18 0 -2 0.5 1 2 3 4 8 12 FREQUENCY - GHz Pulse Response @ PIN = 0 dBm 1.50 16 Input Flatness @FREQUENCY Vo = 1.0 V - GHz 17 0.5 1 2 3 4 8 12 FREQUENCY - GHz 16 17 2.00 17.5 18 -25 dBm -15 dBm 0 dBm 1.75 1.50 1.25 -6 -7 0 -8 1.00 0.1 0.1 0.5 1 2 3 4 8 12 FREQUENCY - GHz 16 17 17.5 INPUT POWER - dBm 0.5 1 2 3 4 8 12 FREQUENCY - GHz 16 17 17.5 18 0 Input VSWR @ Pin = -15 dBm 2.00 -1 1.75 -2 0.1 1.50 0.5 1 2 3 4 2 3 4 8 12 FREQUENCY - GHz 16 17 Pulse Response Tc= +25°C, +85°C, -55°C @ PIN = –15 dBm Input Flatness @ Vo = 3.0 V 1 1 10.0 2 -2 0.5 Transfer Curve @ 2.0 GHz 18 -1 8 12 FREQUENCY - GHz 16 17 17.5 18 1.0 Top Trace: Detector Response Bottom Trace: RF Input Time Base: 500 ηsec 0.1 0.01 Input VSWR @ Pin = -15 dBm 2.00 0.001 -30 -25 -20 1.75 VSWR 1.00 0.11.500.5 1 2 3 4 8 12 FREQUENCY - GHz 16 17 17.5 1 2 3 4 8 12 FREQUENCY - GHz 16 17 17.5 18 -25 dBm -15 dBm 0 dBm Input VSWR vs Input Power 2.00 1.50 -25 dBm -15 dBm 0 dBm 1.75 1.50 1.00 1.25 0.1 0.5 1 1.00 0.1 0.5 10 2 1 3 2 4 3 4 8 12 FREQUENCY - GHz 16 8 12 FREQUENCY - GHz 16 17 17 17.5 17.5 0 5 10 0 5 10 1.0 0.1 0.01 18 0.001 -30 18 -25 -20 Transfer Curve @ 2.0 GHz 10.0 5 Tc= +25°C, +85°C, -55°C 0.5 OUTPUT VOLTAGE - VOLTS 1.75 0 10.0 Input VSWR vs Input Power 1.00 0.1 -15 -10 -5 INPUT POWER - dBm Transfer Curve @ 10.0 GHz 18 1.25 VSWR 17.5 Input VSWR vs Input Power 18 Input Flatness @ Vo = 3.0 V -5 0.1 VSWR 17 -1 1.00 0.1 -19 1 1.25 16 1.75 2 2.00 8 12 FREQUENCY - GHz 1.25 -8 1.25 4 Input VSWR @ Pin = -15 dBm -6 -7 3 2.00 -17 -5 2 1 18 VSWR INPUT POWER - dBm 17.5 -16 0.1 INPUT POWER - dBm 17 VSWR 0.5 1 2 0.1 -20 0.1 Input Flatness@ @ Vo Input Flatness Vo==100 1.0mV V VSWR INPUT POWER - dBm DACP18001 -17 0.5 Input Flatness @ Vo = 3.0 V OUTPUT VOLTAGE - VOLTS INPUT POWER - dBm Input Flatness @ Vo = 100 mV -16 KEY: +25 °C +85 °C -55 °C Transfer Curve @ 2.0 GHz -15 -10 -5 INPUT POWER - dBm Transfer Curve @ 18.0 GHz 10.0 10.0 Tc= +25°C, +85°C, -55°C OUTPUT VOLTAGE - VOLTS OUTPUT VOLTAGE - VOLTS Tc= +25°C, +85°C, -55°C 1.0 1.0 0.1 0.1 0.01 0.01 0.001 -30 0.001 -30 -25 -20 -15 -10 -5 INPUT POWER - dBm -25 -20Curve-15 Transfer @ 10.0-10 GHz -5 0 5 0 0.1 0.01 0.001 -30 10 5 1.0 -25 -20 -15 -10 -5 INPUT POWER - dBm 10 650-691-9800 • Fax: 650-962-6845 INPUT POWER - dBm • Updates: www.teledynemicrowave.com • [email protected] 10.0 LTS OUTPUT VOLTAGE - VOLTS Tc= +25°C, +85°C, -55°C 10.0 Tc= +25°C, +85°C, -55°C Transfer Curve @ 10.0 GHz 1.0 Rev. 7/10 0.01 TO 18.0 GHz ULTRA BROADBAND HIGH FREQUENCY THRESHOLD DETECTOR DTCP18001 DTCP18001 Typical Values @ +25 °C Wide Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . 0.01 to 20.0 GHz Wide Power Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25.0 to -5.0 dBm Temperature Stability . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.50 dB Power Flatness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.50 dB High Frequency CougarPak™ Package External Adjustable Threshold Level, Fast Response Time, Low Drift, Insensitive Threshold Level to Applied Voltage High Frequency CougarPak™ (SMA) DTCP18001 for Threshold Detectors High Frequency CougarPak Package (single-stage) ® for Detectors SPECIFICATIONS* Parameter Typical Frequency (Min.) Guaranteed 0 to 50 °C -55 to +85 °C 0.01 - 20.0 GHz 0.01 - 18.0 GHz 0.01 - 18.0 GHz -30 to -5 dBm* -25 to -5 dBm* -20 to -5 dBm* 1.5:1† 2.0:1† 2.0:1† Power Flatness (Max.) RTH=100kΩ 0.01 – 18.0 GHz 0.01 – 20.0 GHz RTH=1kΩ 0.01 – 18.0 GHz 0.01 – 20.0 GHz RTH=20kΩ 0.01 – 18.0 GHz 0.01 – 20.0 GHz ±0.5 dB ±0.75 dB ±0.5 dB 0.75 dB ±1.0 dB ±1.0 dB ±0.75 dB ±1.0 dB ±0.75 dB ±1.0 dB ±1.25 dB ±1.25 dB ±0.75 dB ±1.0 dB ±0.75 dB ±1.0 dB ±1.25 dB ±1.25 dB Threshold Temp. Stability (Max.) ±0.25 dB ±0.5 dB ±0.5 dB Threshold Hysteresis (Max.) ±0.2 dB ±0.5 dB ±0.5 dB Pulse Response (Max.) 50 µsec‡ 100 µsec‡ 100 µsec‡ Input Power Range (Min.) VSWR (Max.) 1 1 1 Output Voltage Hi @ 5mA source Logic: Pin > Pth 4.4 Volts 3.5 Volts 3.5 Volts Output Voltage Lo @ 5mA sink 0.1 Volts 0.25 Volts 0.25 Volts Supply Current (Max.) 2.5 mA† 5.0 mA† 5.0 mA† *Measured in a 50 Ohm system at Vs=+5.0 Vdc. RTH=100 Ohm to 100 kOhm unless otherwise specified. †Pin ≤-15 dBm. ‡50% RF to 10 or 90% Video Response time for input change ≥ 3 dB above Pth. MAXMUM RATINGS DC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . Operating Case Temperature . . . . . . . . . . . . . . . . . . . . Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Detector Thermal Resistance1 (θjc) . . . . . . . . . . . . . . . Temperature Rise @ 0 dBm . . . . . . . . . . . . . . . . . . . . . 1 Thermal +7 V +14.0 dBm -55 °C to +125 °C -65 °C to +125 °C +125 °C +3500 °C/Watt +3.5 °C Teledyne Cougar • 408-522-3838 • 408-522-3839 fax www.teledyne-cougar.com • [email protected] resistance is based on RF input power. Ratings based on +25 °C. APPLICATION NOTES This unit is DC coupled and employs a RF choke at the input (DC short). DO NOT bypass the Threshold Control pin. Capacitance greater than 50pF may cause instabilities. Keep the threshold programming resistor or circuit close to this pin. Average power detection is obtained at power levels below approximately –13 dBm. The output of this unit is derived from an op-amp, not a true logic device. Connect external threshold resistor from Rcntl port to ground. DIMENSIONS ARE IN INCHES [MILLIMETERS] 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] Threshold Power @ R = 20 KOhms 0.0 RF INPUT - dBm -1.0 -2.0 DTCP18001 -3.0 DTCP18001TYPICAL PERFORMANCE Typical Performance -4.0 -5.0 -6.0 0 1 2 3 4 6 8 10 12 14 FREQUENCY - GHz 16 17 18 19 20 6 8 10 12 14 FREQUENCY - GHz 16 17 18 19 20 2.25 -21.0 2.00 -22.0 1.75 VSWR RF INPUT - dBm Input VSWR -20.0 -23.0 1.50 -24.0 1.25 -25.0 1.00 0 1 2 3 4 -26.0 0 1 2 3 4 6 8 10 12 14 FREQUENCY - GHz 16 17 18 19 20 Threshold Power @ R = 1 KOhms -12.0 Input VSWR at Different Power Levels 4.00 3.50 -14.0 VSWR -16.0 0 1 2 3 4 6 8 10 12 14 FREQUENCY - GHz 16 17 18 19 20 Threshold Power @ R = 20 KOhms 0.0 RF INPUT - dBm -1.0 20 Frequency = 10 GHz 1.50 -18.0 19 2.50 2.00 100000 -17.0 18 Control Resistance vs. Threshold Power (dBm) 3.00 1000000 -15.0 -2.0 -3.0 CONTROL RESISTANCE (Ohm) RF INPUT - dBm -13.0 1.00 10000 0 1 2 3 4 6 8 10 12 14 FREQUENCY - GHz 16 17 18 19 20 1000 100 -4.0 10 -5.0 Pulse Response @ RTH =100 Ohms -6.0 0 1 2 3 4 6 8 10 12 14 FREQUENCY - GHz 16 17 18 19 20 1 -40 Input VSWR -35 -30 -25 -20 -15 THRESHOLD POWER - dBm 2.25 Control Resistance vs. Threshold Power (dBm) VSWR 2.00 1000000 1.75 Frequency = 10 GHz 1.50 100000 19 20 CONTROL RESISTANCE (Ohm) 1.25 18 1.00 10000 0 Pulse Response @ RTH = 1 kOhms 1 2 3 4 6 8 10 12 14 FREQUENCY - GHz 16 17 18 19 20 1000 Input VSWR at Different Power Levels 4.00 100 3.50 VSWR 3.00 10 18 19 20 Pulse Response @ RTH = 20 kOhms 2.50 2.001 -40 -35 -30 -25 -20 -15 THRESHOLD POWER - dBm 1.50 -10 -5 0 Top Trace: TTL Logic Out Bottom Trace: RF Input Time Base: 10.0 µs/div 1.00 0 1 2 3 4 6 8 10 12 14 16 17 18 19 20 650-691-9800 • FREQUENCY Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] - GHz -10 -5 Rev. 7/10 0.5 TO 20.0 GHz HIGH-SPEED ANALOG DETECTOR DACP20021 DACP20021 Typical Values @ +25 °C Wide Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . Wide Power Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature Stability . . . . . . . . . . . . . . . . . . . . . . . . . . Power Flatness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Low VSWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Super fast pulse response . . . . . . . . . . . . . . . . . . . . . . High Freq CougarPak® Package Fast Response Time, Low Drift 0.5 to 20.0 GHz -30.0 to +5.0 dBm ± 0.5 dB ± 1.0 dB 1.75:1 15-20 ηs DACP20021 High Frequency CougarPak™ (SMA) for Analog Detectors High Frequency CougarPak Package (single-stage) for Detectors ® SPECIFICATIONS* Parameter Typical Frequency (Min.) Input Power Range (Min.) VSWR (Max.) Guaranteed 0 to 50 °C -40 to +85°C 0.5-20.0 GHz 0.5-18.0 GHz 0.5-18.0 GHz -30 to +5 dBm -25 to 0 dBm -25 to 0 dBm 1.5:1 2.0:1 2.0:1 2.3:1 2.0:1 2.3:1 1.0-20.0 GHz 0.5-1.0 GHz Sensitivity, Vout (Min.) 140 mV† 90 mV† 90 mV† Power Flatness (Max.) ±0.75 dB ±1.0 dB ±1.0 dB Temperature Stability (Max.) ±0.4 dB ±0.5 dB ±0.5 dB Pulse Response, Pin = -15 dBm 15 ηsec‡ 35/50 ηsec‡ 35/50 ηsec‡ Pulse Response, Pin = 0 dBm 22 ηsec‡ 50/70 ηsec‡ 50/70 ηsec‡ Supply Current, no RF (Max.) 9 mA 10 mA 12 mA Supply Current, Pin = 5 dBm (Max.) 13 mA 16 mA 18 mA 2 mV 4 mV 5 mV -10 dBm — — Output Offset Voltage, no RF (Max.) DIMENSIONS ARE IN INCHES [MILLIMETERS] 1 dB Square Law Departure *Measured in a 50 Ohm system at ±5.0 Vdc unless otherwise specified. †Pin = –15 dBm. ‡Total response time, Tr/Tf: 50% RF to 90 or 10% Video. 50 Ohm output load. MAXMUM RATINGS DC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . Operating Case Temperature . . . . . . . . . . . . . . . . . . . . Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Detector Thermal Resistance1 (θjc) . . . . . . . . . . . . . . . Temperature Rise @ 0 dBm (Tjc) . . . . . . . . . . . . . . . . . Temperature Rise @ +5 dBm (Tjc) . . . . . . . . . . . . . . . . 1 Thermal Teledyne Cougar • 408-522-3838 • 408-522-3839 fax www.teledyne-cougar.com • [email protected] ±6.0 V +14.0 dBm -40 °C to +85 °C -65 °C to +125 °C +125 °C +3500 °C/Watt +3.5 °C +35 °C Pulse Response @ Pin = 0 dBm resistance is based on RF input power. Ratings based on +25 °C. APPLICATION NOTES Average power detection is obtained at power levels below approximately –13dBm. RF input is AC coupled (DC block). DACP20021 contains a plastic packaged IC. DACP20021 provides maximum video performance with no output load capacitance. However, the detector is capable of driving capacitive loads up to 100 pF without oscillations. Load capacitance above that specified may produce pulse overshoot and ringing. DACP20021 contains 50-Ohm series resistor at the output. Pulse Response @ Pin = -15 dBm Top Trace: Detector Response Bottom Trace: RF Input Time Base: 100 ηs/div 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] CP20021 DACP20021 Input VSWR @ Pin = -15 dBm 3.0 l Performance Typical Performance DACP20021 VSWR 2.5 2.0 Typical Performance DACP20021 1.5 1.0 0.1 0.5 1.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 17.0 18.0 19.0 20.0 FREQUENCY - GHz KEY: +25°C +85°C Input Flatness @ Vo = 100 mV -40°C KEY: +25°C +85°C -40°C TYPICAL PERFORMANCE INPUT POWER - dBm @ Vo = 100 mV -14.0 -15.0 Transfer Curve KEY: @ 2.0+25°C GHz KEY: +25°C +85°C -40°C -17.0 -18.0 0.5 1.0 2.0 0.01 4.0 0.001 -3.0 -4.0 -30 -3.0 -4.0 -6.0 OUTPUT VOLTAGE - VOLTS 5.0 1.0 -5.0 -6.0 4.0 3.0 18.0 19.0 2.0 4.0 Input VSWR @ Pin = -15 dBm 2.0 0 10 2.0 1.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 17.0 18.0 19.0 20.0 FREQUENCY - GHz 18.0 19.0 20.0 0 0.0 -40 10 Transfer Curve @ 10.0 GHz Transfer Curve @ 2.0 GHz -30 -20 -10 INPUT POWER - dBm 0 10 1.0 2.0 4.0 1.5 Input VSWR @ Pin = -15 dBm 1.0 0.1 2.5 0.5 1.0 2.0 2.0 1.5 1.0 0.1 0.5 1.0 2.0 4.0 6.0 0.1 4.0 8.0 OUTPUT VOLTAGE - VOLTS 2.0 0.5 OUTPUT VOLTAGE - VOLTS 0.1 6.0 8.0 10.0 12.0 14.0 16.0 17.0 18.0 19.0 20.0 FREQUENCY - GHz 0.01 0.01 0.001 0.001 10.0 12.0 14.0 16.0 17.0 18.0 19.0 20.0 0.0001 -20 -40 -10 -30 INPUT POWER - dBm 0 -20 10 -10 INPUT POWER - dBm 0.01 0.1 0.01 0.001 10.0 0.0001 LOG10 SCALE -40 0.0001 -20-40 -10 -30 0 -20 10 -10 INPUT POWER - dBm INPUT POWER - dBm -30 0.001 1.0 0.0001 -40 0 0.0001 -40 10 -30 3.0 2.0 1.0 0.01 0.1 0.01 0.001 4.0 0.001 1.0 KEY: +25°C +85°C -40°C 3.0 2.0 1.0 4.0 3.0 2.0 KEY: +25°C +85°C -40°C 1.0 0.1 0.01 2.0 GHz Transfer Curve Transfer Curve @ 10.0 GHz 0.001 10 0.0001 -10 -30 0 -20 -40 10 -10 -30 INPUT POWER - dBm INPUT POWER - dBm @ 10.0 GHz 4.0 0 -20 1 INPUT POW Transfer Curve @ 5.0 5.0 KEY: +25°C +85°C 4.0 LTS +25°C +85°C TS +85°C 4.0 LTS TS LTS LINEAR SCALE LINEAR SCALE KEY: KEY: +25°C +25°C 4.0 +85°C 0.0 0 dBm -20-40 5.0 5.0 0.01 0.0001 -40 -30 -10 0.0001 0.0-20 INPUT -10 0 POWER-30 100 -20-40 10 -10-30 -40 0 -20 10 INPUT POWER - dBm INPUT POWER - dBm 5.0 0.1 0.001 1.0 LINEAR SCALE LINEAR SCALE • [email protected] 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com KEY: 4.0 KEY: +25°C +85°C -40°C 0.0001 -30 -20 0.0 -10 0 10 0.0 INPUT -20 -10 POWER -400 - dBm -3010 -20 -40 -10 -30 INPUT POWER - dBm INPUT POWER - dBm Transfer @ Transfer Curve @Curve 2.0 GHz 5.0 0.1 KEY: +25°C +85°C -40°C OUTPUT VOLTAGE - VOLTS 2.0 KEY: +25°C +85°C -40°C 0 LINEAR SCALE KEY: +25°C +85°C 4.0 TS 0.001 3.0 4.0 OUTPUT VOLTAGE - VOLTS 0.01 KEY: +25°C +85°C -40°C 0 OUTPUT VOLTAGE - VOLTS 4.0 OUTPUT VOLTAGE - VOLTS KEY: +25°C 0.1 +85°C -40°C OUTPUT VOLTAGE - VOLTS 0.01 -30 OUTPUT VOLTAGE - VOLTS 0.1 0.1 LOG SCALE KEY: +25°C +85°C -40°C 1 LOG SCALE KEY: KEY: Transfer Curve @ 2.0 GHz Transfer Curve @ Curve @ 10.0 GHz Transfer Curve Transfer Transfer Curve1.0@ 10.0 GHz @ 18.0 GHz Transfer Curve Transfer @ 2.0 GHz Curve @ 10.0 GHz 1.0 1.0 +25°C +25°C 10.0 10.0 5.0 5.0 5.0 5.0 +85°C +85°C -40°C -40°C LINEAR SCALE LINEAR SCALE LOG SCALE LOG SCALE LOG SCALE LINEAR SCALE LINEAR SCALE OUTPUT VOLTAGE - VOLTS 1.0 1.0 10.0 0.0001 -40 10 10.0 10.0 LOG SCALE KEY: +25°C 1.0 +85°C -40°C Transfer Curve @ 10.0 GHz 10.0 0 10.0 0.001 TransferFREQUENCY Curve @- GHz 2.0 GHz OUTPUT VOLTAGE - VOLTS 1.0 LOG SCALE LOG SCALE KEY: KEY: 6.0 8.0 10.0 14.0 16.0 17.0 1.0 18.0 19.0 20.0 1.0 12.0 +25°C +25°C FREQUENCY - +85°C GHz +85°C -40°C -40°C OUTPUT VOLTAGE - VOLTS 2.0 Transfer Curve Transfer @ 18.0 GHz Curve @ 10.0 GHz 10.0 OUTPUT VOLTAGE - VOLTS 10.0 2.5 VSWR INPUT POWER - dBm 3.0 3.0 VSWR -20 -10 INPUT POWER - dBm LINEAR SCALE KEY: +25°C 4.0 20.0 +85°C 6.0 8.0 10.0 12.0 14.0 16.0 17.0 18.0 19.0 20.0 -40°C FREQUENCY - GHz 3.0 1.5 1.0 -30 Transfer Curve @ 10.0 GHz 2.5 2.0 3.0 0.1 OUTPUT VOLTAGE - VOLTS 0.0001 -40 @ 10 Vo = 3.0 V Input VSWR @ Pin = -15 dBm 4.0 e @ 2.0 GHz -10 WER - dBm 6.0 8.0 10.0 12.0 14.0 16.0 17.0 18.0 19.0 20.0 FREQUENCY - GHz 3.0 2.0 OUTPUT VOLTAGE - VOLTS -10 WER - dBm 4.0 5.0 0.1 0.5 1.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 17.0 1.0 18.0 19.0 20.0 6.0 8.0 10.0 12.0 14.0 16.0 17.0 18.0 19.0 20.0FREQUENCY - GHz 0.1 0.5 1.0 1.0 FREQUENCY - GHz 0.1 0.5 1.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 17.0 Input Flatness @ Vo = 0.0 3.0 V -40FREQUENCY -30 -20 -10 - GHz 5.0 INPUT POWER - dBm @ 2.0 GHz 2.0 3.0 = 3.0 V VSWR -4.0 0.01 Transfer Curve 4.0 @ 2.0 GHz 5.0 -5.0 INPUT POWER - dBm INPUT POWER - dBm -3.0 0.1 0.001 0.5 +85°C -40°C Input Flatness -20 -10 0 INPUT5.0 POWER - dBm INPUT POWER - dBm -40 Input Flatness @ Vo = 3.0 1.0 Input Flatness @ VVo -2.0 Pin = -15 dBm 4.0 Input Flatness @ Vo = 1.0 V LINEAR SCALE KEY: 2.0 -18.0 0.1 0.5 1.0 2.0 4.0 4.06.0 +25°C 8.0 10.0 12.0 14.0 16.0 17.0 0.1 0.5 1.0 2.0 4.0 6.0 8.0 10.0 12.0+85°C 14.0 16.0 17.0 1.0 18.0 19.0 20.0 - GHz 0.1 0.5 1.0 6.0 8.0 10.0 12.0 14.0 16.0 17.0 18.0 19.0 20.0FREQUENCYFREQUENCY - GHz -40°C FREQUENCY - GHz -17.0 2.0 OUTPUT VOLTAGE - VOLTS INPUT POWER - dBm INPUT POWER - dBm 1.0 -2.0 -6.0 Input Flatness @ Vo =KEY: 1.0 V +25°C0.1 Input Flatness @ Vo0.0001 = 100 mV -16.0 0.5 LOG SCALE KEY: 1.0 +25°C 6.0 8.0 10.0 12.0 14.0 16.0 17.0 18.0 +85°C 19.0 20.0 FREQUENCY - GHz -40°C 6.0 8.0 10.0 12.0 14.0 16.0 17.0 18.0 19.0 20.0 -5.0 FREQUENCY - GHz 6.0 8.0 10.0 12.0 14.0 16.0 17.0 18.0 19.0 20.0 -2.0 FREQUENCY - GHz -15.0 0.1 INPUT POWER - dBm 0.1 Typical Performance 0.1 @ Vo = 3.0 V -14.0 -18.0 DACP20021 -16.0 Transfer Curve @ 10.0 GHz 10.0 +85°C -40°C OUTPUT VOLTAGE - VOLTS 1.0 6.0 8.0 10.0 12.0 14.0 16.0 17.0 18.0 19.0 20.0 -15.0 FREQUENCY - GHz @ Vo = 1.0 V -16.0 Input Flatness @ Vo 100 mV LOG=SCALE -17.0 -14.0 OUTPUT VOLTAGE - VOLTS INPUT POWER - dBm 10.0 4/11 DA2CP20047 0.5 TO 20.0 GHz LOG VIDEO AMP ANALOG DETECTOR DA2CP20047 Typical Values @ +25 °C Wide Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . 40 dB Power Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Provides a Compressed Transfer Response . . . . . . . . . Temperature Stable Detection . . . . . . . . . . . . . . . . . . . . . Small, Rugged, Hermetic Sealed Cougar Pak Wideband Power Monitor for Medium to High Power 0.5 – 20 GHz -20 to +20 dBm Vo = 0 to 1.3 V +/- 1 dB DA2CP20047 High Frequency CougarPak™ (SMA) Highfor Frequency CougarPak™ Package Detector (two-stage) for Detectors SPECIFICATIONS* Parameter Typical Guaranteed 0 to 50 °C -40 to +85°C Frequency (Min.) 0.5 – 22.0 GHz 0.5 – 20.0 GHz 0.5 – 20.0 GHz Input Power Range (Min.) -25 to +20 dBm -20 to +20 dBm -20 to +20 dBm 1.6:1 2.0:1 2.0:1 +0.70 V +0.68 V +0.65V Temperature Stability (Max.) ± 0.4 dB ± 1.0 dB ± 1.5 dB Power Flatness (Max.) (constant Vo) 0.5 -20 GHz 0.5 - 16 GHz ± 1.0 dB ±0.5 dB ±1.5 dB ±0.5 dB ±1.5 dB ±0.75 dB VSWR (Max.) Sensitivity, Vout (Min.) at 0 dBm Rise Time (Max.)‡ 30 ms 40 ms 40 ms Fall Time (Max.) ‡ 90 ms 100 ms 100 ms Supply Current (Max.) ± 1.5 mA ± 2.5 mA ± 2.5 mA Output Offset Voltage, no RF -0.2 V 0V to -0.3 V 0V to -0.3V * Measured in a 50 Ohm system at ±5.0 Vdc unless otherwise specified. ‡ Total response time, Tr/Tf: 50% RF to 90 or 10% Video. 10k Ohm output load. Teledyne Cougar • 408-522-3838 • 408-522-3839 fax www.teledyne-cougar.com • [email protected] MAXMUM RATINGS DC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . Operating Case Temperature . . . . . . . . . . . . . . . . . . . . Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Detector Thermal Resistance1 (θjc) . . . . . . . . . . . . . . . Temperature Rise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Thermal ±10.0 V +23.0 dBm -40 °C to +85 °C -55 °C to +125 °C +85 °C +150 °C/Watt <1 °C resistance is based on RF input power. Ratings based on +25 °C. APPLICATION NOTES Input is AC coupled Output voltage noise increases as RF signal is decreased (due to increasing video gain) and can be > 500mV with no RF Response time increases as RF signal is decreased (also due to increasing video gain) A logging amplifier follows this RF detector. Since the power range covers both the square law and linear regions of the detector, the transfer curve is not linear with Pin (dB). However, a smooth relationship exists which can be easily programmed and calibrated. This detector is accurate for CW signals and will have a different output for signals containing harmonics or AM levels exceeding about -20 dBc. 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] VSW 2.0 DA2CP20047 1.8 1.6 DA2CP20047 1.4 1.2 1.0 TYPICAL PERFORMANCE 0 2 4 2.6 1.2 -13 2.4 1.0 -14 -15 -16 -17 -18 2 4 6 8 10 12 FREQUENCY - GHz 14 16 18 20 8 10 12 14 -10 -5 0 5 FREQUENCY INPUT POWER- GHz - dBm 16 10 18 15 20 16 10 18 15 20 10 15 20 2.0 0.6 1.8 0.4 1.6 0.2 1.4 0.0 1.0 -0.4 0-30 2 -25 4 -20 6 -15 Input VSWR @ Pin = -20 dBm Transfer Curve @ 8.0 GHz 1 1.4 2.8 0 1.2 2.6 -1 -2 -3 -4 2 4 6 8 10 12 FREQUENCY - GHz 14 16 18 20 OUTPUT VOLTAGE VSWR - VOLTS INPUT POWER - dBm 18 1.2 -0.2 20 Input Flatness @ Vo = 0.7 V Input Flatness @ Vo = 1.2 V 1.0 2.4 0.8 2.2 0.6 2.0 0.4 1.8 0.2 1.6 0.0 1.4 20 -0.2 1.2 19 -0.4 1.0 0 -30 2 -25 4 -20 6 -15 18 8 10 12 14 -10 -5 0 5 FREQUENCY INPUT POWER- GHz - dBm Transfer Curve @ 14.0 GHz 1.0 GHz 17 1.4 16 1.2 14 13 0 2 4 6 8 10 12 FREQUENCY - GHz 14 16 18 20 OUTPUT VOLTAGE - VOLTS 15 1.0 0.8 0.6 0.4 0.2 0.0 -0.2 -0.4 -30 -25 -20 -15 -10 -5 0 5 INPUT POWER - dBm Transfer Curve @ 8.0 GHz 1.4 1.2Trace: Detector Response Top Bottom Trace: RF Input 1.0 Time Base: 20 ms/div VOLTAGE - VOLTS INPUT POWER - dBm 16 2.2 0.8 2 -5 0 14 Input VSWR @ Pin = 0GHz dBm Transfer Curve @ 1.0 -12 -19 0 8 10 12 FREQUENCY - GHz 2.8 1.4 VSWR - VOLTS OUTPUT VOLTAGE INPUT POWER - dBm Input Flatness @ Vo = 0.2 V KEY: +25 °C +85 °C -40 °C 6 0.8 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] 0.6 0.4 Rev. 7/10 0.7 TO 20.0 GHz ULTRA HI-SPEED THRESHOLD DETECTOR DTCP20231 DTCP20231 Typical Values @ +25 °C Wide Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . Super-fast Pulse Response . . . . . . . . . . . . . . . . . . . . . Temperature Stability . . . . . . . . . . . . . . . . . . . . . . . . . . Power Flatness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . High Frequency CougarPak® Package External Adjustable Threshold Level, Low Drift 0.7 to 20.0 GHz 5-10 ηs ± 1.0 dB ± 1.0 dB High Frequency CougarPak™ (SMA) DTCP20231 for Threshold Detectors High Frequency CougarPak Package (single-stage) ® for Detectors SPECIFICATIONS* Parameter Typical Guaranteed 0 to 50 °C -40 to +85 °C Frequency (Min.) 0.7-20.0 GHz 0.7-20.0 GHz 0.7-20.0 GHz Input Power Range (Min.) VSWR (Max.) At Pin= –15 dBm Freq: 0.7 to 8.0 GHz Freq: 8.0 to 20.0 GHz At Pin= –4 dBm Freq: 0.7 to 8.0 GHz Freq: 8.0 to 20.0 GHz Power Flatness (Max.) At –10 dBm At –3 dBm Threshold Temp. Stability (Max.) Threshold Hysteresis (Max.) Pulse Response (Max.) At 50 Ω˙˙ 8 pF load Logic: Pin > Pth Output Volt. Hi @ 5mA source (Min.) Output Volt. Lo @ 5mA sink (Max.) Supply Current (Max.) -15 to -3 dBm* -15 to -5 dBm* -15 to -5 dBm* 2.5:1 1.8:1 3.0:1 2.3:1 3.0:1 2.3:1 3.0:1 2.8:1 3.8:1 3.5:1 3.8:1 3.5:1 ±0.75 dB ±1.25 dB ±0.25 dB ±0.2 dB ±1.0 dB ±1.50 dB ±0.5 dB ±1.0 dB ±1.0 dB ±1.50 dB ±0.5 dB ±1.5 dB 8^ ηsec 1 4.4 Volts 0.27 Volts 7.0 mA 13^ ηsec 1 3.5 Volts 0.5 Volts 10.0 mA 15^ ηsec 1 3.5 Volts 0.5 Volts 12.0 mA * Measured in a 50 Ohm system at Vs=+5.0 Vdc. Rth=2 Ohm to 2 KOhm unless otherwise specified. ^ 50% RF to 10 or 90% Video Response time for input change 3 dB above Pth. MAXMUM RATINGS DC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous RF Input Power . . . . . . . . . . . . . . . . . . . . . Operating Case Temperature . . . . . . . . . . . . . . . . . . . . Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Burn-In Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . Detector Thermal Resistance1 (θjc) . . . . . . . . . . . . . . . Temperature Rise @ 0 dBm . . . . . . . . . . . . . . . . . . . . . 1 Thermal +6 V +14.0 dBm -40 °C to +125 °C -65 °C to +150 °C +125 °C +3500 °C/Watt +3.5 °C Teledyne Cougar • 408-522-3838 • 408-522-3839 fax www.teledyne-cougar.com • [email protected] resistance is based on RF input power. Ratings based on +25 °C. APPLICATION NOTES RF input is AC coupled (DC block). DTCP20231 contains a plastic packaged IC-Ultra Hi-speed comparator. DTCP20231 provides maximum performance with minimum output capacitance. A heavy capacitive load slows down the TTL output response. Connect external threshold resistor from Rcntl port to ground. DIMENSIONS ARE IN INCHES [MILLIMETERS] 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] RF INPUT - d -10 -11 -12 DTCP20231 -13 -14 0 1 2 3 4 6 8 10 12 14 FREQUENCY - GHz 16 DTCP20231 17 18 19 20 TYPICAL PERFORMANCE Threshold Power @ R = 500 Ohms Typical Performance 0 -2 Threshold Power @ R = 20 KEY: +25°C +85°C Ohms -40°C Control Resistance vs. Threshold Power (dBm) -8 -3 CONTROL RESISTANCE (Ohm) RF INPUT - dBm RF INPUT - dBm -1 -9 -4 -5 -10 -6 -11 0 1 -12 -13 2 3 4 6 8 10 12 14 FREQUENCY - GHz 16 17 18 19 20 Input VSWR @ Pin = –12 dBm 3.5 3.0 1000 Frequency = 10 GHz 100 10 1 -14 VSWR 02.5 2.0 1 2 3 4 6 8 10 12 14 FREQUENCY - GHz 16 17 18 19 -18 -16 -14 -12 -10 -8 THRESHOLD POWER - dBm 20 -6 -4 -2 Threshold Power @ R = 500 Ohms 0 1.5 Pulse Response 0 1 2 3 4 6 -2 8 10 12 14 FREQUENCY - GHz 16 17 18 19 20 90% -4 3.5 3.0 VSWR -5 50% 2.5 -6 02.0 1.5 1 2 3 4 6 8 10 12 14 FREQUENCY - GHz 16 17 18 19 20 Input VSWR @ Pin = –12 dBm 3.5 1.0 0 1 2 3 4 6 3.0 8 10 12 14 FREQUENCY - GHz 16 17 18 19 20 100 50% t=0 1 -18 -16 RF Input t=0 t = 7.5ηs F 10 = 2.0 GHz, Rise Time -14 t = 9.0ηs F = 2.0 GHz, Fall Time -12 -10 -8 THRESHOLD POWER - dBm -6 90% 0.5 1.5 0.0 1.0 -0.5 0 4.0 TTL Out 10% Frequency RF Input= 10 GHz TTL Out 1.0 2.0 1000 Hysterisis Vs Threshold Power 2.5 HYSTERISIS - dB VSWR TTL Out Control Resistance vs. Threshold Power (dBm) Input VSWR @ –4 dBm -3 4.0 CONTROL RESISTANCE (Ohm) RF INPUT - dBm -1 1.0 RF Input 1 2 3 4 6 -1.0 -1.5 8 10 12 14 FREQUENCY - GHz 16 17 18 19 20 50% t=0 Input VSWR @ –4 dBm 10% TTL Out 50% RF Input t = 8.0ηs -2.0 3.5 -12 -11 -10 -9 -8 -7 INPUT POWER - dBm -6 -5 -4 t = 8.0ηs t=0 F = 10.0 GHz, Fall Time F = 10.0 GHz, Rise Time -3 VSWR 3.0 2.5 TTL Out 90% 2.0 1.5 1.0 0 1 2 3 4 6 8 10 12 14 FREQUENCY - GHz 16 17 18 19 20 50% RF Input t=0 Hysterisis Vs Threshold Power t = 12.5ηs F = 18.0 GHz, Rise Time 1.0 10% TTL Out 50% RF Input t=0 t = 8.0ηs F = 18.0 GHz, Fall Time HYSTERISIS - dB 0.5 0.0 TTL Logic Out 800 mV/div RF Input 20 mV/div Time Base: 2.0 ηs/div -0.5 -1.0 -1.5 -2.0 -12 -11 -10 -9 -8 -7 INPUT POWER - dBm -6 -5 -4 -3 650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected] -4 -2