Supertex inc. HV9930DB1 High Bright LED Driver IC Demoboard Meeting Automotive Requirements General Description Specifications The HV9930DB1 is an LED driver demoboard capable of driving up to 7 1-watt LEDs in series from an automotive input of 9 - 16VDC. The demoboard uses Supertex’s HV9930 in a boost-buck topology. The converter operates at frequencies in excess of 300kHz and has excellent output current regulation over the input voltage range. It can also withstand transients up to 42V and operate down to 6V input. The converter is also protected against open LED and output short circuit conditions. Protection against reverse polarity up to 20V is also included. Parameter Input voltage (steady state): Value 9.0VDC - 16VDC Input voltage (transient): 42VDC Output LED string voltage: Output current: 28V max 350mA +/-5% Output current ripple: 5% typical Switching frequency: 300kHz (9.0V input) 430kHz (13.5V input) 500kHz (16.0V input) Efficiency: 80% (at 13.5V input) Open LED protection: Output short circuit protection: Included; clamps output voltage at 33V Included; limits current at 350mA Reverse polarity protection: -20V max Input current limit: PWM dimming frequency: Conducted EMI: 1.9A Up to 1.0kHz Meets SAE J1113 conducted EMI standards Board Layout and Connection Diagram _ + + - VIN _ + PWM Dimming Actual Size: 2.25” x 1.25” + Enable Connections: Input - The input is connected between the terminals of square wave source between terminals 1 and 3 of connector connector J1 as shown in the Connection Diagram. J3 as shown by the dotted lines. Output - The output is connected between the terminals of Note: connector J2 as shown. Enable/PWM Dimming: To just enable the board, short pins 1 and 2 of connector J3 as shown. For PWM dimming, connect the external push-pull Doc.# DSDB-HV9930DB1 A032913 During PWM dimming, pin 2 of connector J3 should be left open. Also, the PWM signal must have the proper polarity with the positive connected to pin 1 of J3. Note that pin 3 of J3 is internally connected to the return path of the input voltage. Supertex inc. www.supertex.com HV9930DB1 Testing the Demo Board Fig. 2 shows the variation of the switching frequency over the input votage range. The frequency varies from 300kHz to 500kHz over the entire input voltage range and avoids the restricted frequency band of 150kHz to 300kHz and the AM band greater than 530kHz. This makes it easier to meet the conducted and radiated EMI specifications for the automotive industry. Normal Operation: Connect the input source and the output LEDs as shown in the Connection Diagram and enable the board. The LEDs will glow with a steady intensity. Connecting an ammeter in series with the LEDs will allow measurement of the LED current. The current will be 350mA +/- 5%. Switching Frequency (kHz) Open LED test: Connect a voltmeter across the output terminals of the HV9930DB1. Start the demoboard normally, and once the LED current reaches steady state, unplug one end of the LED string from the demoboard. The output voltage will rise to about 33V and stabilize. Short Circuit Test: When the HV9930DB1 is operating in steady state, connect a jumper across the terminals of the LED string. Notice that the switching frequency drops, but the average output current remains the same. 450 400 350 300 8 10 12 14 16 18 Input Voltage (V) PWM Dimming: With the input voltage to the board disconnected, apply a TTL compatible, push-pull square wave signal between PWMD and GND terminals of connector J3 as shown in the Connection Diagram. Turn the input voltage back on and adjust the duty cycle and / or frequency of the PWM dimming signal. The output current will track the PWM dimming signal. Note that although the converter operates perfectly well at 1.0kHz PWM dimming frequency, the best PWM dimming ratios can be obtained at lower frequencies like 100 or 200Hz Fig.3 shows the output current variation over the input voltage range. The LED current has a variation of about 2.0mA over the entire voltage range. Fig. 3 Output Current vs. Input Voltage Output Current (mA) 350.5 Typical Results Fig. 1 shows the efficiency plot for the HV9930DB1 over the input voltage range. The converter has efficiencies greater than 80% over 13V input. Note that these measurements do not include the 0.3 - 0.5W loss in the reverse blocking diode. 350.0 349.5 349.0 348.5 348.0 8 10 12 14 16 18 Input Voltage (V) Fig. 1 Efficiency vs. Input Voltage 84 Efficiency (%) Fig.2 Switching Frequency vs. Input Voltage 500 82 80 78 76 74 72 70 8 10 12 14 16 18 Input Voltage (V) Doc.# DSDB-HV9930DB1 A032913 2 Supertex inc. www.supertex.com HV9930DB1 The waveforms in Fig.4 show the drain voltage of the FET (channel 1 (blue); 10V/div) and the LED current (channel 4 (green); 100mA/div) at three different operating conditions – 9.0V in, 13.5V in and 16V in. Fig. 5 shows the operation of the converter during cold crank conditions as the input voltage decreases from 13.5V to 6V and increases back to 13.5V. In these cases, the input current reaches the limit set and the output current drops correspondingly. Thus, the LEDs continue to glow, but with reduced intensity. Once the voltage ramps back up, the output current goes back to its normal value and the converter comes out of the input current limit. Fig. 4. Steady State Waveforms (a): 9.0V in; (b): 13.5V in; (c): 16V in Fig. 5. Cold Crank Operation Channel 1 (blue): Input voltage (10V/div) Channel 3 (pink): Input current (1A/div) Channel 4 (green): LED current; 100mA/div (a) Fig.6 shows the LED current during an input step change from 13.5 to 42V and back to 13.5V (similar to a clamped load dump). It can be seen that the LED current drops briefly when the input voltage jumps, but there are no overshoots. Fig. 6 LED current during step changes in the input voltage (b) Channel 1(blue): Input voltage (10V/div) Channel 4 (green): LED current (100mA/div) (c) Doc.# DSDB-HV9930DB1 A032913 3 Supertex inc. www.supertex.com HV9930DB1 Fig. 7a shows the operation of the converter during an Open LED condition and Fig. 7b shows the operation during output short circuit condition. In both cases, it can be seen that the HV9930DB1 can easily withstand faults and come back into normal operation almost instantly. Fig. 8 shows the PWM dimming performance of the HV9930DB1 with a 100Hz, 3.3V square wave signal. The converter can easily operate at PWM dimming duty cycles from 1% - 99%. Fig. 8 PWM Dimming at 100Hz Channel 1 (blue): PWM Dimming Input Signal (2V/div) Channel 4 (Green): LED current (100mA/div) Fig. 7 HV9930DB1 during output fault conditions FET drain voltage (20V/div) Channel 1 in (a); Channel 2 in (b) Channel 4 (green): LED current (a) (a): Open LED Condition Short Circuit (b) (b): Output Short Circuit (c) Doc.# DSDB-HV9930DB1 A032913 4 Supertex inc. www.supertex.com HV9930DB1 Conducted EMI Tests on the HV9930DB1 Fig. 9 shows the rise and fall times of the output current during PWM dimming. The converter has nearly symmetric rise and fall times of about 25µs. These rise and fall times can be reduced (if desired) by reducing the output capacitance C10. However, this will lead to increased ripple in the output current. In preliminary tests conducted on the demo board, the board meets SAE J1113 Class 3 conducted EMI standards without the need for any input filters (other than the input capacitors already included). This is a result of the combination of the continuous input current and a localized switching loop (Q1 – C1 – D3). Fig. 9. PWM Dimming rise and fall times Channel 1 (blue): PWM Dimming Input Signal (2V/div) Channel 4 (Green): LED current (100mA/div) Table 1 details the conducted EMI limit as per SAE J1113 and the maximum conducted EMI obtained from measurements on the board. The table also lists the Class of the SAE standard the board meets in each frequency range. The conducted EMI plots for the HV9930DB1 obtained at an input voltage of 13.5V and an LED string voltage of 27V (output current is 350mA) are given in the Appendix. (a): rise time (b): fall time Table 1. Conducted EMI Measurements Conducted EMI Limit for Class 3 Conducted EMI by HV9930DB1 (dBµV) (dBµV) 150 - 300 70 (narrowband) 40 Class 5 530 - 2.0 50 (narrowband) 48 Class 3 5.9 - 6.2 45 (narrowband) 29 Class 5 30 - 54z 65 (broadband) 54 Class 4 70 - 108 49 (broadband) 47 Class 3 Frequency Range (kHz) Doc.# DSDB-HV9930DB1 A032913 5 Class as per SAE J1113 Supertex inc. www.supertex.com Doc.# DSDB-HV9930DB1 A032913 6 J3A J3B 1 2 3 J3C 2 J1B 1 J1A C2 4.7µF 25V REF C9 2.2µF 16V C2 4.7µF 25V R7 10kΩ C2 4.7µF 25V 5 2 6 VIN 1 REF GATE 3 CS2 PWMD GND CS1 HV9930 VDD U1 D4 1N4148 R4 4.42kΩ C2 4.7µF 25V B220-13 D1 7 4 8 R5 10kΩ 2 C8 1.0µF 16V Q2 2N3907A R3 0.47Ω 1/2W DR125-820 L1 R1 0.47Ω 1/2W 1 REF 1 Q1 FDS3692 R2 4.7Ω 1/2W C5 4.7µF 50V D3 B2100-13 C1 0.1µF 50V 1 R9 100kΩ R8 1.69Ω 1/4W R11 10kΩ R10 5.49kΩ 2 D2 33V 350mW DR74-151 L2 REF 2 J2B C10 0.1µF 50V 1 J2A HV9930DB1 Circuit Schematic: Supertex inc. www.supertex.com HV9930DB1 PCB Top Layer PCB Bottom Layer Doc.# DSDB-HV9930DB1 A032913 7 Supertex inc. www.supertex.com HV9930DB1 Appendix – Conducted EMI Test Results Ref. Level = 70dBµV Ref. Level = 50dBµV Ref. Level = 45dBµV Doc.# DSDB-HV9930DB1 A032913 8 Supertex inc. www.supertex.com HV9930DB1 Appendix – Conducted EMI Test Results (cont.) Ref. Level = 65dBµV Ref. Level = 49dBµV Doc.# DSDB-HV9930DB1 A032913 9 Supertex inc. www.supertex.com HV9930DB1 Bill of Materials # Quan Ref Des Description C1 0.22µF, 50V X7R ceramic capacitor Package Manufacturer Manufacturer’s Part # SMD1210 Kemet C1210C224K5RACTU SMD1210 Panasonic ECJ-4YB1E475K 1 1 2 3 3 1 C5 4.7µF, 50V X7R ceramic capacitor SMD1210 Murata GRM32ER71H475KA88L 4 1 C8 1µF, 16V X7R ceramic capacitor SMD0805 Kemet C0805C105K4RACTU 5 1 C9 2.2µF, 16V X7R ceramic capacitor SMD0805 TDK Corp. C2012X7R1C225K 6 1 C10 0.1µF, 50V X7R ceramic capacitor SMD0805 Yageo 08052R104K9B20D 7 1 D1 20V, 2A schottky diode SMB Diodes Inc. B220-13 8 1 D2 33V, 350mW zener diode SOT-23 Zetex Inc. BZX84C33-7 9 1 D3 75V, 400mW switching diode SOD123 Diodes Inc. 1N4148W-7 10 1 D4 100V, 2A schottky diode SMB Diodes Inc. B2100-13 11 2 J1, J2 2 pin, 2.5mm pitch right angle connector Thru-Hole JST Sales S2B-EH 12 1 J3 3 pin, 2.5mm pitch right angle connector Thru-Hole JST Sales S3B-EH 13 1 L1 82µH, 2A rms, 2.4A sat inductor SMT Coiltronics DR125-820 14 1 L2 150µH, 0.86A rms, 1A sat inductor SMT Coiltronics DR74-151 15 1 Q1 100V, 4.5A N-channel MOSFET SO-8 Fairchild Semi FDS3692 16 1 Q2 -60V, 600mA PNP transistor SOT-23 Zetex Inc. FMMT2907ATA 17 1 R1, R3 0.47Ω, 1/2W, 5% chip resistor SMD2010 Panasonic ERJ-12ZQJR47U 18 1 R2 8.2Ω, 1/2W, 5% chip resistor SMD2010 Panasonic ERJ-12ZYJ8R2U 19 1 R4 4.42kΩ, 1/8W, 1% chip resistor SMD0805 Yageo 9C08052A4421FKHFT 20 1 R5 10Ω, 1/8W, 1% chip resistor SMD0805 Yageo 9C08052A10R0FKHFT 21 2 SMD0805 Yageo 9C08052A1002FKHFT 22 1 R8 1.69Ω, 1/4W, 1% chip resistor SMD1206 Yageo 9C12063A1R69FGHFT 23 1 R9 100Ω, 1/8W, 1% chip resistor SMD0805 Yageo 9C08052A1000FKHFT 24 1 R10 5.49kΩ, 1/8W, 1% chip resistor SMD0805 Yageo 9C08052A5491FKHFT 25 1 U1 Boost-Buck LED Driver SO-8 Supertex HV9930LG-G C2, C3, 4.7µF, 25V X5R ceramic capacitor C4, C6 R7, R11 10kΩ, 1/8W, 1% chip resistor Supertex inc. does not recommend the use of its products in life support applications, and will not knowingly sell them for use in such applications unless it receives an adequate “product liability indemnification insurance agreement.” Supertex inc. does not assume responsibility for use of devices described, and limits its liability to the replacement of the devices determined defective due to workmanship. No responsibility is assumed for possible omissions and inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications refer to the Supertex inc. (website: http//www.supertex.com) Supertex inc. ©2013 Supertex inc. All rights reserved. Unauthorized use or reproduction is prohibited. Doc.# DSDB-HV9930DB1 A032913 10 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com