IQ Networks Product Selection Guide

IQ Networks
Catalog Products (EAR99/Non-ITAR)
Typical and guaranteed specifications vary versus frequency;
see detailed data sheets for specification variations.
High Performance IQ Modulators and Image Reject Mixers
Typical and Guaranteed Specifications—50 Ω System
Frequency Range
Model
LO Power
dBm
Nominal
Conversion Loss
RF
GHz
LO
IQM2811
IQM4221
IQM11621
IQM18621
1.4-2.8
2.1-4.1
6.0-10.8
15.0-18.0
1.4-2.8
2.1-4.1
6.0-10.8
15.0-18.0
DC-0.5
DC-0.5
DC-0.5
DC-0.5
13
10
10
13
10.5
9.0
8.5
10.0
11.5
10.0
10.0
12.0
42
40
25
25
35
33
20
20
40
42
40
30
IQM15101
IQM15103
IQM17131
IQM17133
10.5-14.5
10.5-14.5
13.2-16.8
13.2-16.8
10.5-14.5
10.5-14.5
13.2-16.8
13.2-16.8
DC-0.5
DC-0.5
DC-0.5
DC-0.5
10
13
10
13
6.3
6.3
6.5
6.5
8.0
8.0
8.0
8.0
25
25
25
25
20
20
20
20
28
28
30
30
IF
dB
Typ.
Isolation
dB
dB
Max.
L to R
Typ.
Min.
Image Reject
L to I/Q
Typ.
Min.
dB
Typ.
Min.
30
35
33
23
25
25
28
23
20
20
23
18
22
22
23
23
23
23
23
23
18
18
18
18
Available in Standard Cougar Mixer Carriers
High Performance IQ (Quadraphase) Modulators
Typical and Guaranteed Specifications—50 Ω System
Model
Frequency Range
MHz
Carrier
Carrier
I/QData Port
Center
Bandwidth
Bandwidth1
Freq. (fo)
Carrier
Input
Power
dBm
Nominal
Data Signal
Insertion
Levels
Loss
L to R
Input to Output
Low
High
dB
dB
mA Nom.Typ. Max.
Typ.
Carrier
Phase
Isolation
Accuracy
Input to Output
dB
dB
Deg
Deg
Max.
Typ.
Max.
Typ.
Amplitude
Balance
dB
Max.
dB
Max
VSWR
10% Bandwidth – Available in Cougar Flatpack
IQF034
IQF124
IQF504
IQF1004
30
120
500
1000
10 % of fo
10 % of fo
10 % of fo
10 % of fo
DC to 50 Min.
DC to 50 Min.
DC to 50 Min.
DC to 50 Min.
IQ069
IQ150
60
150
fo ± 20 MHz
fo ± 50 MHz
DC to 50 Min.
DC to 50 Min.
0
0
0
0
-20
-20
-20
-20
20
20
20
20
4
4
7
7
6
6
9
9
55
50
40
30
45
40
30
20
±2
±2
±2
±2
±4
±4
±5
±5
0.25
0.25
0.5
0.5
0.5
0.5
1.0
1.0
1.5:1
1.5:1
1.5:1
1.5:1
45
40
90 ± 4
90 ± 4
90 ± 5
90 ± 5
0.25
0.25
0.5
0.5
1.5:1
1.5:1
Octave Bandwidth – Available in Cougar Flatpack
0
0
-20
-20
20
20
4
4
6
6
55
50
Current data sheets available on website. 1RF and IQ Bandwidths are typically much greater than specified.
650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected]
Typical and guaranteed specifications vary versus frequency;
see detailed data sheets for specification variations.
High Performance IQ Demodulators
Typical and Guaranteed Specifications—50 Ω System
Model
Frequency Range
MHz
RF/LO1
LO
I/Q
Center
Bandwidth
Bandwidth1
Freq. (fo)
LO
Power
dBm
Nominal
Conversion
Loss
dB
Typ.
dB
Max.
Isolation
L to R
dB
dB
Typ.
Max.
I to Q Balance
L to I/Q
dB
dB
Typ.
Max.
VSWR
Phase
Deg
Deg
Typ.
Max.
Amplitude
dB
dB
Typ.
Max.
Max
10% Bandwidth – Available in Cougar Flatpack
IQF030
IQF031
30
30
10 % of fo
10 % of fo
DC to 50 Min.
DC to 50 Min.
+10
+10
9
9
11
11
55
55
45
45
55
55
45
45
90 ± 3
90 ± 1
90 ± 5
90 ± 2
0.10
0.1
0.50
0.2
1.5:1
1.5:1
IQF120
IQF121
120
120
10 % of fo
10 % of fo
DC to 50 Min.
DC to 50 Min.
+10
+10
9
9
11
11
50
50
45
40
55
55
45
45
90 ± 3
90 ± 1
90 ± 5
90 ± 2
0.15
0.1
0.50
0.2
1.5:1
1.5:1
IQF500
IQF501
500
500
10 % of fo
10 % of fo
DC to 50 Min.
DC to 50 Min.
+10
+10
9
9
11
11
40
40
30
30
40
40
30
30
90 ± 3
90 ± 1
90 ± 5
90 ± 2
0.25
0.1
0.75
0.2
1.5:1
1.5:1
IQF1000
IQF1001
1000
1000
10 % of fo
10 % of fo
DC to 50 Min.
DC to 50 Min.
+10
+10
10
10
12
12
40
40
30
30
30
30
20
20
90 ± 3
90 ± 1
90 ± 5
90 ± 2
0.35
0.1
1.0
0.2
1.5:1
1.5:1
IQF1500
IQF1501
1500
1500
10 % of fo
10 % of fo
DC to 50 Min.
DC to 50 Min.
+10
+10
10
10
12
12
30
30
20
20
20
20
15
15
90 ± 3
90 ± 1
90 ± 5
90 ± 2
0.5
0.1
1.0
0.2
1.5:1
1.5:1
45
90 ± 4
90 ± 5
0.25
0.50
1.5:1
Octave Bandwidth – Available in Cougar Flatpack
IQ068
60
fo ± 20 MHz
DC to 50 Min.
+10
9
11
55
45
55
Current data sheets available on website. 1RF and IQ Bandwidths are typically much greater than specified.
650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected]
Rev. 1/12
1.4 TO 2.8 GHz
IQ MIXER
MODULATOR/DEMODULATOR
IQM2811
IQM2811
Typical Values
LO & RF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Third Order I.P. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conversion Loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LO Drive (nominal). . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Isolation (LO to RF) . . . . . . . . . . . . . . . . . . . . . . .
Standard Mixer Carrier
IQM2811
1.4 - 2.8 GHz
DC - 0.5 GHz
+13.0 dBm
-9.0 dB
+13.0 dBm
42.0 dB
Mixer Carrier MC6
SPECIFICATIONS*
Frequency
(GHz)
Typ.
(dB)
SSB Conversion Loss
and
SSB Noise Figure
fR
fL
fI
fR
fL
fI
1.6 to 2.8
1.6 to 2.8
DC to 0.5
1.4 to 2.8
1.4 to 2.8
DC to 0.5
8.5
8.5
8.5
10.5
10.5
10.5
9.5
9.5
9.5
11.5
11.5
11.5
Conversion Comp.
Desenitization
fR
fR2
Level = +5 dBm
Level = +2 dBm
–
–
1.0
1.0
Min.
(dB)
35
30
25
Isolation
fL at R
fL at I, Q
fR at I, Q
fL
fL
fR
1.4 to 2.0
1.4 to 2.0
1.4 to 2.0
Typ.
(dB)
42
40
32
fL at R
fL at I, Q
fR at I, Q
fL
fL
fR
2.0 to 2.8
2.0 to 2.8
2.0 to 2.8
46
50
36
36
42
30
Third Order Intercept
LO = +13 dBm
LO = +16 dBm
+15 dBm
+16 dBm
—
—
Image Rejection
Side Band Suppression
RF = 1.4 to 2.8 GHz
IF = 0.5 GHz
25 dB
20 dB
Amplitude Match
RF = 1.4 to 1.8 GHz
RF = 1.8 to 2.8 GHz
0.5 dB
0.15 dB
1.0 dB
0.25 dB
Phase Match
(Demodulation)
RF = 1.4 to 2.8 GHz
4.0°
6.0°
Phase Match
(Modulation)
RF = 1.4 to 1.8 GHz
RF = 1.8 to 2.8 GHz
±25.0°
±15.0°
±30.0°
±22.0°
Conversion Loss
(Modulation)
RF = 1.4 to 1.8 GHz
RF = 1.8 to 2.8 GHz
-9.5 dB
-7.0 dB
-11.0 dB
-8.5 dB
* Measured in a 50-ohm system with nominal LO drive of +13 dBm as a downconverter.
ABSOLUTE MAXIMUM RATINGS
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . .
-65 to +150 °C
Peak RF Input Power All Ports . . . . . . . . . . . . . . . . . . . +22 dBm @ 25 °C
derate to +17 dBm @ 100 °C
DIMENSIONS ARE IN INCHES [MILLIMETERS]
Harmonic Intermodulation Products
(single tone)
5
HARMONICS OF f R
Port
4
3
2
1
94
93
93
93
78
74
83
83
27
27
93
93
95
91
95
95
78
82
0
0
9
15
0
1
0
95
94
94
95
95
96
61
59
65
59
35
37
94
95
96
96
64
56
81
78
53
53
7
9
96
96
95
90
94
94
88
82
35
36
26
31
2
3
4
HARMONICS OF f L
F R = 2000 MHz @ -10 dBm
F L = 2030 MHz
F L @ +13 dBm
F L @ +16 dBm
96
94
97
96
95
95
56
55
36
39
40
40
5
Harmonic Intermodulation Products
(single tone)
5
HARMONICS OF f R
Parameter
Guaranteed
-55 to +85 °C
Max.
(dB)
4
3
2
1
88
90
92
92
93
93
67
65
30
30
92
93
94
94
92
89
82
82
0
0
13
19
0
1
0
93
93
96
95
94
93
65
67
48
52
12
16
95
96
96
96
61
59
81
82
31
33
31
31
96
96
97
95
96
95
76
79
50
49
33
37
2
3
4
HARMONICS OF f L
F R = 2800 MHz @ -10 dBm
F L = 2830 MHz
F L @ +13 dBm
F L @ +16 dBm
650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected]
98
98
96
95
80
74
76
74
53
59
30
31
5
IQM2811
TYPICAL PERFORMANCE
Isolation (L to I) vs
KEY: +25 ¡ C
+85 ¡ C
1
Frequency
-55 ¡ C
Conversion Loss vs LO Drive Level
-9
CONVERSION LOSS - dB
ISOLATION - dB
-30
-35
-40
-45
-50
2
-8
F L at +13 dBm
Series 1
Series 2
-10
-11
F L = 2.2 GHz, Low-Side LO
F I = 30 MHz
-12
-13
The minimum recommended drive level is +6 dBm.
The maximum recommended drive level is +22 dBm.
-14
-55
1.4 1.5
1.6
1.8
2.0
2.2
FREQUENCY - GHz
2.4
2.6
2.7 2.8
-15
1
2
4
6
8
10
12 13
14
15
LO POWER - dBm
16
17
18
20
21
2.6
2.7
2.8
2.6
2.7
2.8
Power at P1db Compression Point
-30
7
-40
-50
F L at +13 dBm
-60
1.4 1.5
1.6
1.8
2.0
2.2
FREQUENCY - GHz
2.4
2.6
2.7 2.8
P1dB (dBm)
ISOLATION - dB
Isolation (L to R) vs Frequency1
SN1
SN2
SN3
6
SN4
SN5
5
4
3
1.4 1.5
Isolation (R to I) vs Frequency
1.6
1.8
2.0
2.2
FREQUENCY - GHz
2.4
-30
-35
-40
F L = 2 GHz @ +13 dBm
-45
1.4 1.5
1.6
1.8
2.0
2.2
FREQUENCY - GHz
2.4
2.6
2.7 2.8
Conversion Loss vs RF Frequenc y 2
CONVERSION LOSS - dB
ISOLATION - dB
-25
-7
F L at +13 dBm
-8
-9
-10
-11
1.4 1.5
1.6
1.8
2.0
2.2
FREQUENCY - GHz
2.4
1
Level of the fL signal fed through to the R- and I-ports with respect to the level of the fL signal
at the L-port.
2
Conversion loss of the mixer when used in an SSB system. The frequency ordinate
refers to the R-port (fR) with fI at 30 MHz.
0.0
-0.5
F L = 3 GHz @ +13 dBm
HH-LH
LL-HL
110
70
50
1.4 1.5
1.6
1.8
2.0
2.2
FREQUENCY - GHz
2.4
2.6
2.7 2.8
1.6
1.8
100
F L = +13 dBm, Low-side LO
F I = 30 MHz
90
85
80
1.4 1.5
45
1.6
1.8
2.0
2.2
FREQUENCY - GHz
2.0
2.2
FREQUENCY - GHz
2.4
2.6
2.7
2.8
0.8
0.9
1.0
2.7
2.8
Relative IF Response
10.0
I/Q Quadrative Phase Balance
95
LH-LL
HL-HH
90
-1.0
RELATIVE IF RESPONSE - dB
PHASE BALANCE - deg
PHASE (Deg)
0.5
1.4 1.5
IMAGE REJECT - dB
Modulation (QPSK)
130
2.4
2.6
2.7 2.8
F L = 2.2 GHz
7.5
5.0
2.5
0
+13dBm I-Port
+13dBm Q-Port
-2.5
-5.0
-7.5
-1.0
Image Rejection
-0.9
-0.8 -0.7
-0.6 -0.4 -0.2
0
0.2 0.4 0.6
RELATIVE IF FREQUENCY - GHZ
0.7
Intercept Point
70
40
F L = +13 dBm
I F = 0.5 GHz
INTERCEPT POINT - dBm
AMP BALANCE - dB
I/Q Amplitude Balance
1.0
35
30
25
20
1.4 1.5
1.6
1.8
2.0
2.2
2.4
LO FREQUENCY - GHz
2.6
2.7 2.8
60
I F = 30 MHz
R F at -10 dBm
Hi-Side LO
50
40
I Port IP3LO at +13dBm
I Port IP2LO at +13dBm
30
Q Port IP3LO at +13dBm
Q Port IP2LO at +13dBm
20
10
0
1.4 1.5
1.6
1.8
2.0
2.2
FREQUENCY - GHz
2.4
650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected]
2.6
Rev. 5/10
1.9 TO 4.2 GHz
IQ MIXER
MODULATOR/DEMODULATOR
IQM4221
IQM4221
Typical Values
LO & RF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Third Order I.P. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conversion Loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LO Drive (nominal). . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Isolation (LO to RF) . . . . . . . . . . . . . . . . . . . . . . .
Standard Mixer Carrier
IQM4221
1.9 - 4.2 GHz
DC - 1.1 GHz
+13.0 dBm
-10.0 dB
+10.0 dBm
42.0 dB
Mixer Carrier MC4
SPECIFICATIONS*
Frequency
(GHz)
Typ.
(dB)
SSB Conversion Loss
and
SSB Noise Figure
fR
fL
fI
fR
fL
fI
2.1 to 4.1
2.1 to 4.1
DC to 0.5
1.9 to 4.1
1.9 to 4.1
0.6 to 1.1
9.0
9.0
9.0
11.0
11.0
11.0
10.0
10.0
10.0
13.0
13.0
13.0
Conversion Comp.
Desenitization
fR
fR2
Level = +3 dBm
Level = +2 dBm
–
–
1.0
1.0
Min.
(dB)
33
18
28
Isolation
fL at R
fL at I
fR at I
fL
fL
fR
1.9 to 3.0
1.9 to 3.0
1.9 to 2.7
Typ.
(dB)
40
25
32
fL at R
fL at I
fR at I
fL
fL
fR
3.0 to 4.2
3.0 to 4.2
2.7 to 4.2
45
42
35
40
35
33
LO = +10 dBm
LO = +13 dBm
+12 dBm
+12 dBm
—
—
Image Rejection
Side Band Suppression
RF = 1.9 to 4.2 GHz
IF = 0.5 GHz
25 dB
20 dB
Amplitude Match
RF = 1.9 to 4.2 GHz
0.2 dB
0.3 dB
Phase Match
(Demodulation)
RF = 1.9 to 4.2 GHz
2.0°
4.0°
Phase Match
(Modulation)
RF = 2.5 to 3.5 GHz
RF = 1.9 to 4.2 GHz
±5.0°
±10.0°
±8.0°
±15.0°
Conversion Loss
(Modulation)
RF = 2.5 to 4.2 GHz
RF = 1.9 to 4.2 GHz
-7 dB
-10 dB
-8 dB
-11.5 dB
Third Order Intercept
DIMENSIONS ARE IN INCHES [MILLIMETERS]
Harmonic Intermodulation Products
(single tone)
5
HARMONICS OF f R
Port
4
3
2
1
93
93
93
93
93
65
76
72
19
19
93
93
94
95
94
90
37
38
0
0
-11
-9
0
1
0
* Measured in a 50-ohm system with nominal LO drive of +10 dBm as a downconverter.
ABSOLUTE MAXIMUM RATINGS
94
95
73
69
73
47
40
41
53
56
28
33
92
91
77
78
77
73
71
71
36
41
30
32
82
78
78
72
78
93
66
67
56
55
40
45
5
Harmonic Intermodulation Products
(single tone)
5
4
3
2
1
90
90
92
91
91
90
78
76
26
26
92
92
93
92
94
94
80
78
0
0
14
18
0
1
0
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . .
-65 to +150 °C
Peak RF Input Power All Ports . . . . . . . . . . . . . . . . . . . +22 dBm @ 25 °C
derate to +17 dBm @ 100 °C
94
94
94
94
94
67
50
47
31
31
16
17
2
3
4
HARMONICS OF f L
F R = 2000 MHz @ -10 dBm
F L = 2030 MHz
F L @ +10 dBm
F L @ +13 dBm
HARMONICS OF f R
Parameter
Guaranteed
-55 to +85 °C
Max.
(dB)
93
93
95
94
93
92
66
65
48
52
24
27
93
93
96
95
61
59
80
79
49
49
21
19
96
95
96
92
94
92
79
75
61
63
40
45
2
3
4
HARMONICS OF f L
F R = 4000 MHz @ -10 dBm
F L = 4030 MHz
F L @ +10 dBm
F L @ +13 dBm
650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected]
96
97
96
96
95
94
65
69
50
50
29
33
5
IQM4221
TYPICAL PERFORMANCE
CONVERSION LOSS - dB
ISOLATION - dB
50
40
F L at +10 dBm
30
20
10
1.9 2.0
2.1
2.5
2.9
3.3
FREQUENCY - GHz
ISOLATION - dB
Isolation (L to R) vs
3.7
3.9
30
2.5
F L = 3.0 GHz, Low-Side LO
F I = 30 MHz
-12
-13
The minimum recommended drive level is +5 dBm.
The maximum recommended drive level is +22 dBm.
-14
-15
0
40
2.1
-11
2
4
6
8
10
Frequency1
F L at +10 dBm
1.9 2.0
-10
4.0 4.1
60
50
2.9
3.3
FREQUENCY - GHz
3.7
3.9
4.0 4.1
20
10
1.9 2.0
2.1
2.5
2.9
3.3
FREQUENCY - GHz
3.7
3.9
4.0 4.1
18
19
20
3.9
4.0
4.1
3.9
4.0
4.1
10
9
8
1.9 2.0
2.1
2.5
2.9
3.3
FREQUENCY - GHz
3.7
Conversion Loss vs RF Frequenc y 2
12
F L at +13 dBm
11
10
9
8
1.9 2.0
2.1
2.5
2.9
3.3
FREQUENCY - GHz
1
Level of the fL signal fed through to the R- and I-ports with respect to the level of the fL signal
at the L-port.
17
F L at +10 dBm
11
CONVERSION LOSS - dB
ISOLATION - dB
30
16
Conversion Loss vs RF Frequency 2
50
F L = 3 GHz @ +10 dBm
12 13
14
15
LO POWER - dBm
12
Isolation (R to I) vs Frequency
40
2
-9
CONVERSION LOSS - dB
Isolation (L to I) vs
Conversion Loss vs LO Drive Level
KEY: +25 °C
+85 °C
Frequency1
-55 °C
3.7
2
Conversion loss of the mixer when used in an SSB system. The frequency ordinate
refers to the R-port (fR) with fI at 30 MHz.
I/Q Amplitude Balance
12
Q Port
I Port
110
PHASE (Deg)
CL - dB
Modulation (QPSK)
F L = 3 GHz @ +10 dBm
11
10
9
8
1.9 2.0
2.1
2.5
2.9
3.3
FREQUENCY - GHz
3.7
3.9
RELATIVE IF RESPONSE - dB
PHASE BALANCE - deg
86
84
82
27.5
3.7
3.9
4.1 4.2
25.0
22.5
2.1
2.5
3.7
3.9
4.1
4.2
1.0
1.1
1.2
2.9
3.3
3.7
LO FREQUENCY - GHz
4.1
4.2
-0.5
-1.0
+10dBm I-Port
+10dBm Q-Port
-1.5
+13dBm I-Port
+13dBm Q-Port
-2.0
-2.5
-1.1
-1.0 -0.8 -0.6 -0.4 -0.2 0
0.2 0.4 0.6
RELATIVE IF FREQUENCY - GHZ
0.8
70
F L = +10 dBm
I F = 0.5 GHz
20.0
1.9 2.0
2.9
3.3
FREQUENCY - GHz
Intercept Point
Image Rejection
3.9
4.1 4.2
INTERCEPT POINT - dBm
IMAGE REJECT - dB
30.0
2.5
F L = 3 GHz
0.0
-3.0
-1.2
80
2.9
3.3
FREQUENCY - GHz
2.1
Relative IF Response
88
2.5
80
0.5
F L = 3.0 GHz at +10 dBm
2.1
90
1.9 2.0
I/Q Quadrative Phase Balance
1.9 2.0
LH-LL
HL-HH
70
4.0 4.1
92
90
HH-LH
LL-HL
100
I F = 30 MHz
R F at -10 dBm
Hi-Side LO
60
IP3LO at +10dBm
IP2LO at +10dBm
IP3LO at +13dBm
IP2LO at +13dBm
50
40
30
20
10
0
1.9
2.0
2.1
2.5
2.9
3.3
FREQUENCY - GHz
3.7
650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected]
3.9
Rev. 5/10
6.0 TO 10.8 GHz
IQ MIXER
MODULATOR/DEMODULATOR
IQM11621
IQM11621
Typical Values
LO & RF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Third Order I.P. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conversion Loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LO Drive (nominal). . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Isolation (LO to RF) . . . . . . . . . . . . . . . . . . . . . . .
Standard Mixer Carrier
IQM11621
6.0 - 10.8GHz
DC - 0.5 GHz
+15.0 dBm
-9.0 dB
+10.0 dBm
30.0 dB
Mixer Carrier MC5
SPECIFICATIONS*
Frequency
(GHz)
Typ.
(dB)
SSB Conversion Loss
and
SSB Noise Figure
fR
fL
fI
fR
fL
fI
6.0 to 9.0
6.0 to 9.0
DC to 0.5
9.0 to 10.8
9.0 to 10.8
DC to 0.5
8.5
8.5
8.5
9.0
9.0
9.0
9.5
9.5
9.5
10.0
10.0
10.0
Conversion Comp.
Desenitization
fR
fR2
Level = +3 dBm
Level = +2 dBm
–
–
1.0
1.0
Min.
(dB)
20
33
23
Isolation
fL at R
fL at I
fR at I
fL
fL
fR
6.0 to 8.0
6.0 to 8.0
6.0 to 8.0
Typ.
(dB)
25
40
27
fL at R
fL at I
fR at I
fL
fL
fR
8.0 to 10.8
8.0 to 10.8
8.0 to 10.8
32
45
33
26
38
27
LO = +10 dBm
LO = +13 dBm
+15 dBm
+15 dBm
—
—
Image Rejection
Side Band Suppression
RF = 6.0 to 10.8 GHz
IF = 0.5 GHz
28 dB
23 dB
Amplitude Match
RF = 6.0 to 10.8 GHz
0.5 dB
0.8 dB
Phase Match
(Demodulation)
RF = 6.0 to 10.8 GHz
5.0°
8.0°
Phase Match
(Modulation)
RF = 6.0 to 7.5 GHz
RF = 7.5 to 10.8 GHz
±8.0°
±15.0°
±12.0°
±22.0°
Conversion Loss
(Modulation)
RF = 6.0 to 10.8 GHz
-13 dB
-14.5 dB
Third Order Intercept
DIMENSIONS ARE IN INCHES [MILLIMETERS]
Harmonic Intermodulation Products
(single tone)
5
HARMONICS OF f R
Port
4
3
2
1
86
86
84
83
86
86
71
68
17
18
83
84
89
89
75
73
67
67
0
0
2
5
0
1
0
* Measured in a 50-ohm system with nominal LO drive of +10 dBm as a downconverter.
ABSOLUTE MAXIMUM RATINGS
90
90
90
87
63
61
61
58
31
33
30
30
92
93
90
84
77
74
65
63
56
62
41
42
95
94
93
92
80
78
75
81
52
52
26
31
5
Harmonic Intermodulation Products
(single tone)
5
4
3
2
1
N/A
N/A
76
76
87
89
82
80
24
23
76
77
88
88
90
89
79
74
0
0
24
32
0
1
0
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . .
-65 to +150 °C
Peak RF Input Power All Ports . . . . . . . . . . . . . . . . . . . +22 dBm @ 25 °C
derate to +17 dBm @ 100 °C
89
89
89
89
68
65
47
43
28
29
8
10
2
3
4
HARMONICS OF f L
F R = 6000 MHz @ -10 dBm
F L = 6000 MHz
F L @ +10 dBm
F L @ +13 dBm
HARMONICS OF f R
Parameter
Guaranteed
-55 to +85 °C
Max.
(dB)
89
89
90
90
92
90
55
52
42
46
40
42
90
90
92
93
72
71
76
71
45
46
26
29
92
92
90
87
99
92
76
78
56
53
31
37
2
3
4
HARMONICS OF f L
F R = 9000 MHz @ -10 dBm
F L = 9000 MHz
F L @ +10 dBm
F L @ +13 dBm
650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected]
95
95
92
93
90
90
74
72
48
51
N/A
N/A
5
IQM11621
TYPICAL PERFORMANCE
Isolation (L to I) vs
KEY: +25 ¡ C
+85 ¡ C
Frequency1
-55 ¡ C
-45
-50
6.0 6.5
7.0
7.5
8.0
8.5
FREQUENCY - GHz
ISOLATION - dB
Isolation (L to R) vs
9.0
9.5 10.0 10.5 11.0
-35
-45
6.0 6.5
7.0
7.5
-13
8.0
8.5
FREQUENCY - GHz
9.0
9.5 10.0 10.5 11.0
The minimum recommended drive level is +5 dBm.
The maximum recommended drive level is +22 dBm.
-15
-17
-2
F L at +10 dBm
F L = 8.0 GHz, Low-Side LO
F I = 30 MHz
Q Port
I Port
Frequency1
-15
-25
CONVERSION LOSS - dB
-40
-9
-11
0
2
4
6
8
-35
-40
6.0 6.5
7.0
7.5
8.0
8.5
FREQUENCY - GHz
9.0
9.5 10.0 10.5 11.0
CONVERSION LOSS - dB
ISOLATION - dB
-30
6.0 6.5
7.0
7.5
8.0
8.5
FREQUENCY - GHz
-8
-9
F L at +13 dBm
-10
-11
7.0
7.5
8.0
8.5
FREQUENCY - GHz
PHASE (Deg)
AMP BALANCE - dB
-1.0
7.5
8.0
8.5
FREQUENCY - GHz
9.0
9.5 10.0 10.5 11.0
HH-LH
LL-HL
LH-LL
HL-HH
100
90
80
70
60
I/Q Quadrative Phase Balance
6.0 6.5
F L = 3.0 GHz at +10 dBm
7.0
7.5
8.0
8.5
FREQUENCY - GHz
90
88
86
84
82
8.0
8.5
FREQUENCY - GHz
9.0
0
-1
-2
-3
+10dBm I-Port
+10dBm Q-Port
-4
-1.0 -0.8
+13dBm I-Port
+13dBm Q-Port
-0.6 -0.4 -0.2
0
0.2 0.4 0.6
RELATIVE IF FREQUENCY - GHZ
0.8
1.0
1.2
1.4
Intercept Point
45
INTERCEPT POINT - dBm
F L = +10 dBm
I F = 0.5 GHz
30
25
8.0
8.5
9.0
LO FREQUENCY - GHz
-1.2
9.5 10.0 10.5 11.0
Image Rejection
7.5
10.0 10.5 11.0
F L = 8 GHz
1
-5
-1.4
7.5
9.5
Relative IF Response
RELATIVE IF RESPONSE - dB
92
9.0
2
94
PHASE BALANCE - deg
10.0 10.5 11.0
Conversion loss of the mixer when used in an SSB system. The frequency ordinate
refers to the R-port (fR) with fI at 30 MHz.
96
IMAGE REJECT - dB
9.5
Modulation (QPSK)
-0.5
7.0
9.0
120
0.0
20
6.0 6.5
10.0 10.5 11.0
Conversion Loss vs RF Frequenc y 2
110
35
9.5
2
F L = +10 dBm
7.0
9.0
-7
0.5
6.0 6.5
20
-11
6.0 6.5
I/Q Amplitude Balance
7.0
19
F L at +10 dBm
-10
-1.0
6.0 6.5
18
-9
1
Level of the fL signal fed through to the R- and I-ports with respect to the level of the fL signal
at the L-port.
17
-8
-20
F L = 8 GHz @ +10 dBm
16
-7
Isolation (R to I) vs Frequency
-25
10 12
14
15
LO POWER - dBm
Conversion Loss vs RF Frequency 2
CONVERSION LOSS - dB
ISOLATION - dB
F L at +10 dBm
-35
40
2
Conversion Loss vs LO Drive Level
-7
-30
9.5 10.0 10.5 11.0
40
I F = 30 MHz
R F at -10 dBm
Hi-Side LO
35
30
IP3LO at +10dBm
IP2LO at +10dBm
25
20
15
10
6.0 6.5
P1dB data is available upon request.
IP3LO at +13dBm
IP2LO at +13dBm
7.0
7.5
8.0
8.5
FREQUENCY - GHz
9.0
650-691-9800 • Fax: 650-962-6845 • Updates: www.teledynemicrowave.com • [email protected]
9.5
10.0 10.5 11.0
TELEDYNE
MICROWAVE SOLUTIONS
Everywhereyoulook
TM
teledynemicrowave.com
Tel: 1.800.832.6869 or +1.650.962.6944