PL IA N T Features *R oH S CO M ■ ■ ■ ■ ■ ■ ■ Carbon element Plain or knurled shaft option Metal bushing Metal shaft Rear solder lugs Audio or linear taper options Variety of resistance values ■ Detent at “no-load” position ■ RoHS compliant* PDB241-GNL Series - “No-Load” Guitar Potentiometer Electrical Characteristics Taper ........................................Audio, linear Standard Resistance ........ 10K to 1M ohms Standard Resistance Tolerance........ ±20 % Environmental Characteristics Operating Temperature .................................... -10 °C to +70 °C Power Rating ................................0.25 watt Maximum Operating Voltage ..............250 V Rotational Noise .....................150 mV max. Mechanical Characteristics Mechanical Angle ........................300 ° ±5 ° Rotational Torque .............. 50 to 150 gf-cm Stop Strength .........................8 kg-cm min. Rotational Life ...............15,000 cycles min. Detent Position ................................... 300 ° Detent Torque ......................100-300 gf-cm Soldering Condition Manual Soldering ........................300 °C within 3 seconds Wave Soldering ........................260 °C within 3 seconds Hardware .......................... Two flat washers and two mounting nuts supplied per potentiometer Product Dimensions 12.2 (.480) 12.2 (.480) 1.0 (.039) 19.0 (.748) 9.5 (.374) 6.00 (.236) DIA. 18 TEETH KNURLED SHAFT 24.6 (.969) DIA. 1.0 (.039) 6.00 DIA. (.236) 19.0 (.748) 18 TEETH KNURLED SHAFT (LONG) 6.0 (.236) 24.6 (.969) DIA. 6.0 (.236) 3/8”-32UNF 3/8”-32UNF 6.35 DIA. (.250) PLAIN SHAFT 0.5 (.020) PLAIN SHAFT (LONG) 0.5 (.020) 6.35 DIA. (.250) 24.6 (.969) 30 ° FULL CCW DIA. 60 ° 3/8”-32UNF 9.5 (.374) 4.0 x 1.5 (.158 x .059) 2.4 (.094) 12.6 (.496) 1 2 6.7 (.264) Derating Curve Rating Power Ratio (%) 27.5 (1.083) 3 NUT 6.7 (.264) 2.0 (.079) UNDER 12.0 (.472) DIA. WASHER TOLERANCES: ±0.5 10.0 ~ 100 10.0 ±0.3 = = (.394 ~ 3.937) (±.020) (.394) (±.012) 100 80 60 40 33 20 0 DIA. 3 PLCS. 2.0 (.079) DIA. 3 PLCS. 4.0 (.158) 0 10 20 30 40 50 60 70 80 90 100 Circuit 1 Resistance (Ohms) 10,000 25,000 50,000 100,000 250,000 300,000 500,000 1,000,000 Resistance Code 103 253 503 104 254 304 504 105 MM (INCHES) How To Order Ambient Temperature (°C) Standard Resistance Table DIMENSIONS: 3 2 PDB24 1 - GNL 01 - 504 A2 Model Number of Units 1 = Single Guitar Pot Designator Configuration 01 = Knurled Shaft (18-Tooth) / Solder Lugs 02 = Plain Shaft / Solder Lugs 03 = Knurled Shaft (18-Tooth, Long) / Solder Lugs 04 = Plain Shaft (Long) / Solder Lugs 11 = Knurled Shaft (24-Tooth) / Solder Lugs 13 = Knurled Shaft (24-Tooth, Long) / Solder Lugs Resistance Code (See Table) Resistance Taper (See Taper Charts) *RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011. Specifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time. Users should verify actual device performance in their specific applications. PDB241-GNL Series - “No-Load” Guitar Potentiometer Taper Chart A2 Taper B0 Taper 100 100 90 90 80 Terminal 1-2 Output Voltage X 100 (%) Terminal 1-3 Input Voltage Terminal 1-2 Output Voltage X 100 (%) Terminal 1-3 Input Voltage 80 70 60 50 40 30 20 10 70 60 50 40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 0 10 Rotational Travel (%) 20 30 40 50 60 70 80 90 100 Rotational Travel (%) Inquire for availability of other tapers. REV. 11/13 Specifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time. Users should verify actual device performance in their specific applications.