CA-DVIAT & CA-DVI250R DVI over CAT5 Transmitter & Receiver Box Operation Manual CA-DVIAT&CA-DVI250R Revision History Version No V1 Date 20090401 Summary of Change Preliminary Release Precaution Failure to follow the precautions described below may cause damage to DVI over CAT 5 Transmitter and Receiver Box and void the warranty. DO NOT open the case. Doing so will void the warranty. If you find problem with it, please return back to your retailer or seller who will assist you or provide you with solution. DO NOT use third-Party AC adapter or power cord. Doing so may damage DVI over CAT 5 Transmitter and Receiver Box. DO NOT bump, jar or drop contents of the products as it may damage it and result in warranty void. DO NOT set any liquids or beverages on the drive as they may damage DVI over CAT 5 Transmitter and Receiver Box. Table of Contents 1. Introduction…………………………………………………........………. 1 2. Application…………………………………………………................…. 1 3. Contents……………………………………………….........................… 1 4. System Require…………………………………….…………........……. 1 5. Features…………………………………………….......……........……… 2 6. Operation Controls and Functions……………………………………. 2 6.1 Transmitter’s Front Panel......................................................... 3 6.2 Receiver’s Front Panel………………..........................….….… 4 6.3 Transmitter’s Rear Panel.......................................................... 4 6.4 Receiver’s Rear Panel……………………………….........….… 4 7. Connection and Installation…………………………….........……..… 5 8. Specifications……………………………………………...........……….. 6 1. Introduction DVI transmitter and receiver over CAT 5 is a pair of extender for DVI signal up to 250 meters long. Not only can this device transfer the HD image signal but also the analog/digital audio signal with coaxial and L/R audio port. Through the DDC cable the device can also support HDCP and CEC. This extender is perfect for extending high resolution digital signage with crystal clear images over low cost network solution. 2. Application For long distance DIV/HDMI source display in a separate room or class. For long distance digital or analog sounds transferring up to 250M long. Any PC source equipment with output DVI connector. 3. Contents DVI over CAT 5 Transmitter x 1 DVI over CAT 5 Receiver 250M x 1 Operational Manual x 1 5V/2.6A Power Adaptor x 2 4. System Require PC/DVI/HDMI source with DVI output connector, DVI to DVI or HDMI to DVI cable(s), CAT 5 cable(s) and DVI display monitor or HDMI TV/Monitor. 1 5. Features Compliant with HDMI 1.2, HDCP 1.1 and DVI 1.0 specifications. Support Equalizer, Gain, CTI (Color Transient Improvement) adjustment. Supports high definition input up to 1080P/UXGA, output resolution follows input. Easy to install and simple to operate. Connect CAT 5 back to DVI without signal loss after 250 meter's transmission. Supports DDC/HDCP signal transferring through DDC cable. Build-in EDID at transmitter Support both external Coaxial and Stereo Sound. 6. Operation Controls and Functions 6.1 Transmitter’s Front Panel 1 2 3 4 ① DVI-D IN – Plug from DVI/HDMI source equipment’s video output with DVI in cable. Note: Duo to this device has build-in EDID therefore, when HDIM’s audio signal is send the device may not perform. Hence, it may be adjust from the HDMI source equipment (eg. DVD play) to set the audio output to LPCM or AC3 or DTS or … etc. ② COAX IN – Plug from DVI/HDMI source equipment’s audio output with coaxial cable. Note: This audio signal is received from CAT 5 with SPDIF format and therefore, LPCM sound will perform 2CH. ③ L/R IN – Plug from DVI/HDMI source equipment’s audio output with L/R phone jack cable. ④ AUDIO switch – Switch your audio source by COAX in or L/R in. Note: When audio source input is bit stream format, L/R output will not display hence, audio input source should select LPCM for displayable format. Coaxial output will perform the same signal as to Coaxial inputs’. 2 6.2 Receiver’s Front Panel CTI 1 2 EQUALIZER GAIN CTI 250M 150M 100M 50M 1 MIN VIDEO DDC DC 5V MAX CAT5 INPUT ADJUST 2 3 4 5 6 ① CTI dip switch – Setting CTI by using the twin jumpers to adjust the optimized setting for different distance of connection. CTI 1 2 150 - 250m ↑ ↑ 100 - 150m ↓ ↑ 50 - 100m ↑ ↓ 50 m↓ ↓ ↓ ② EQUALIZER – Use this switch to adjust Sharpness/Peak over long distance by turning right or left. ③ GAIN – Use this switch to adjust Brightness/Contrast by turning right or left. ④ DDC CAT 5 INPUT – Connect the DDC input to the DDC output of the transmitter with CAT-5/CAT-5E/CAT-6 cable. Note: For advanced user only, if it's known that the DDC or HDCP data are required for the source and the display, you can use a single CAT-5 cable for the VIDEO connection only. ⑤ VIDEO CAT 5 INPUT – Connect the VIDEO input to the Video output of the transmitter with CAT-5/CAT-5E/CAT-6 cable. ⑥ Power Jack – Connect with 5V / 2.6A power adaptor with power supply. 3 6.3 Transmitter’s Rear Panel VIDEO DDC DC 5V CAT5 OUTPUT 1 2 3 ① with CAT-5/CAT-5E/CAT-6 cable. ② DDC CAT 5 INPUT – Connect the DDC input to the DDC output of the transmitter with CAT-5/CAT-5E/CAT-6 cable. Note: For advanced user only, if it's known that the DDC or HDCP data are required for the source and the display, you can use a single CAT-5 cable for the VIDEO connection only. ③ Power Jack – Connect with 5V / 2.6A power adaptor with power supply. 6.4 Receiver’s Rear Panel 1 2 3 ① DVI-D OUT – Connect to DVI/HDMI display equipment with DIV or DVI to HDMI cable. ② COAX OUT – Connect to audio amplifier or audio equipment’s input with coaxial cable. Note: This audio signal is received from CAT 5 with SPDIF format and therefore, LPCM sound will perform 2CH. ③ L/R OUT – Connect to audio equipment’s input with 3.5mm phone jack. Note: This audio channel will perform Stereo sound only. When Dolby or DTS signal is send no sound will be performed. 4 7. Connection and Installation PC DVD Player Co-ax Cable DVI Cable L/R Cable VIDEO (CAT-5 Cable) HDMI to DVI Cable DDC (CAT-5 Cable) VIDEO DVI to CAT 5 / TRANSMITTER COAX DVI-D IN COAX IN L/R IN DDC DC 5V L/R 250 Meters AUDIO CAT5 OUTPUT Transmitter unit Front Transmitter unit Rear CTI 1 2 EQUALIZER GAIN CTI 250M 150M 100M 50M MIN DDC VIDEO DC 5V CAT5 to DVI 250M / RECEIVER MAX ADJUST DVI-D OUT CAT5 INPUT COAX OUT L/R OUT Receiver Unit Front Receiver Unit Rear HDMI DVI Cable PC / DVI Display 5 HDMI to DVI Cable LCD Monitor Co-ax Cable Audio Amplifier L/R Cable 8. Specifications Transmitter Input port Transmitter Output port Receiver Input port Receiver Output port Resolution Power Supply Dimensions (mm) Weight (g) Material Color Power Consumption 1 x DVI-I female port (Accept DVI-D signel only) 1 x Coaxial 1 x L/R Audio 2 x CAT5 RJ 45 8pin 2 x CAT5 RJ 45 8pin 1 x DVI-I female port 1 x Coaxial 1 x L/R Audio HD- 480i/p 60, 576p 60, 720P 50/60, 1080i 50/60Hz, 1080p 50/60Hz PC- 640 x 480=VGA72, VGA75, VGA85 800 x 600=SVGA56, SVGA60, SVGA72, SVGA75, SVGA85 1024 x 768=XGA60, XGA70, XGA75, XGA85 1280 x 1024=SXGA60, SXGA75, SXGA85 1600 x 1200=UXGA60 1920 x 1200=Reduced blanking WUXGA 5V / 2.6A DC power supply 125 x 130 x 30 / each 700 /each Aluminum Silver Transmitter: 7W Receiver: 6W 6 CYPRESS TECHNOLOGY CO., LTD. Home page: http://www.cypress.com.tw 20090402 MPM-CADVI250R