GPIO Expander Keypad and LCD Demo Board User’s Guide © 2006 Microchip Technology Inc. DS51636A Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, Accuron, dsPIC, KEELOQ, microID, MPLAB, PIC, PICmicro, PICSTART, PRO MATE, PowerSmart, rfPIC and SmartShunt are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. AmpLab, FilterLab, Migratable Memory, MXDEV, MXLAB, SEEVAL, SmartSensor and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, ECAN, ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, In-Circuit Serial Programming, ICSP, ICEPIC, Linear Active Thermistor, Mindi, MiWi, MPASM, MPLIB, MPLINK, PICkit, PICDEM, PICDEM.net, PICLAB, PICtail, PowerCal, PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB, rfPICDEM, Select Mode, Smart Serial, SmartTel, Total Endurance, UNI/O, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2006, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona, Gresham, Oregon and Mountain View, California. The Company’s quality system processes and procedures are for its PIC® 8-bit MCUs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS51636A-page ii © 2006 Microchip Technology Inc. GPIO EXPANDER KEYPAD AND LCD DEMO BOARD USER’S GUIDE Table of Contents Preface ........................................................................................................................... 1 Introduction............................................................................................................ 1 Document Layout .................................................................................................. 1 Conventions Used in this Guide ............................................................................ 2 Recommended Reading........................................................................................ 2 The Microchip Web Site ........................................................................................ 3 Customer Support ................................................................................................. 3 Document Revision History ................................................................................... 3 Chapter 1. Product Overview ....................................................................................... 5 1.1 Introduction ..................................................................................................... 5 1.2 What is the GPIO Expander Keypad and LCD Demo Board? ....................... 5 1.3 What The GPIO Expander Keypad and LCD Demo Board Kit Includes ........ 5 Chapter 2. Installation and Operation ......................................................................... 7 2.1 Introduction ..................................................................................................... 7 2.2 Features ......................................................................................................... 7 2.3 Getting Started ............................................................................................... 8 2.4 GPIO Expander Keypad and LCD Demo Board Description ......................... 9 2.5 Firmware Description ................................................................................... 10 Appendix A. Schematics and Board Layouts ........................................................... 15 A.1 Introduction .................................................................................................. 15 A.2 Board Schematic - Page 1 ......................................................................... 16 A.3 Board Schematic - Page 2 ......................................................................... 17 A.4 Board Schematic - Page 3 ......................................................................... 18 A.5 Board - Top Layer (with Silk screen) .......................................................... 19 A.6 Board - Bottom Layer ................................................................................. 19 Appendix B. Bill Of Materials (BOM) ......................................................................... 21 Worldwide Sales and Service .................................................................................... 24 © 2006 Microchip Technology Inc. DS51636A-page iii GPIO Expander Keypad and LCD Demo Board User’s Guide NOTES: DS51636A-page iv © 2006 Microchip Technology Inc. GPIO EXPANDER KEYPAD AND LCD DEMO BOARD USER’S GUIDE Preface NOTICE TO CUSTOMERS All documentation becomes dated, and this manual is no exception. Microchip tools and documentation are constantly evolving to meet customer needs, so some actual dialogs and/or tool descriptions may differ from those in this document. Please refer to our web site (www.microchip.com) to obtain the latest documentation available. Documents are identified with a “DS” number. This number is located on the bottom of each page, in front of the page number. The numbering convention for the DS number is “DSXXXXXA”, where “XXXXX” is the document number and “A” is the revision level of the document. INTRODUCTION This chapter contains general information that will be useful to know before using the GPIO Expander Keypad and LCD Demo Board. Items discussed in this chapter include: • • • • • • Document Layout Conventions Used in this Guide Recommended Reading The Microchip Web Site Customer Support Document Revision History DOCUMENT LAYOUT This document describes how to use the GPIO Expander Keypad and LCD Demo Board as a development tool. The manual layout is as follows: • Chapter 1. “Product Overview” – Important information about the GPIO Expander Keypad and LCD Demo Board. • Chapter 2. “Installation and Operation” – Includes instructions on how to get started with this evaluation board. • Appendix A. “Schematics and Board Layouts” – Shows the schematic and layout diagrams for the GPIO Expander Keypad and LCD Demo Board. • Appendix B. “Bill Of Materials (BOM)” – Lists the parts used to build the GPIO Expander Keypad and LCD Demo Board. © 2006 Microchip Technology Inc. DS51636A-page 1 GPIO Expander Keypad and LCD Demo Board User’s Guide CONVENTIONS USED IN THIS GUIDE This manual uses the following documentation conventions: DOCUMENTATION CONVENTIONS Description Arial font: Italic characters Initial caps Quotes Underlined, italic text with right angle bracket Bold characters N‘Rnnnn Text in angle brackets < > Courier New font: Plain Courier New Represents Examples Referenced books Emphasized text A window A dialog A menu selection A field name in a window or dialog A menu path MPLAB® IDE User’s Guide ...is the only compiler... the Output window the Settings dialog select Enable Programmer “Save project before build” A dialog button A tab A number in verilog format, where N is the total number of digits, R is the radix and n is a digit. A key on the keyboard Click OK Click the Power tab 4‘b0010, 2‘hF1 Italic Courier New Sample source code Filenames File paths Keywords Command-line options Bit values Constants A variable argument Square brackets [ ] Optional arguments Curly brackets and pipe character: { | } Choice of mutually exclusive arguments; an OR selection File>Save Press <Enter>, <F1> #define START autoexec.bat c:\mcc18\h _asm, _endasm, static -Opa+, -Opa0, 1 0xFF, ‘A’ file.o, where file can be any valid filename mcc18 [options] file [options] errorlevel {0|1} RECOMMENDED READING For more information regarding the Stand-Alone CAN controller, CAN I/O Expander, and CAN transceiver devices, refer to the appropriate data sheet. Table 1 shows the device and associated Data Sheet literature number. These documents can be found at Microchip’s web site at: www.microchip.com. TABLE 1: DEVICES AND DATA SHEET LITERATURE NUMBERS Device DS51636A-page 2 Literature # Device Literature # MCP23X08 DS21919 PIC18F4550 DS39632 MCP23X17 DS21952 MCP1702 DS22008 © 2006 Microchip Technology Inc. Preface THE MICROCHIP WEB SITE Microchip provides online support via our web site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: • Product Support – Data sheets and errata, application notes and sample programs, design resources, user’s guides and hardware support documents, latest software releases and archived software • General Technical Support – Frequently Asked Questions (FAQs), technical support requests, online discussion groups, Microchip consultant program member listing • Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives CUSTOMER SUPPORT Users of Microchip products can receive assistance through several channels: • • • • • Distributor or Representative Local Sales Office Field Application Engineer (FAE) Technical Support Development Systems Information Line Customers should contact their distributor, representative or field application engineer for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://support.microchip.com DOCUMENT REVISION HISTORY Revision A (October 2006) • Initial Release of this Document. © 2006 Microchip Technology Inc. DS51636A-page 3 GPIO Expander Keypad and LCD Demo Board User’s Guide NOTES: DS51636A-page 4 © 2006 Microchip Technology Inc. GPIO EXPANDER KEYPAD AND LCD DEMO BOARD USER’S GUIDE Chapter 1. Product Overview 1.1 INTRODUCTION This chapter provides an overview of the GPIO Expander Keypad and LCD Demo Board and covers the following topics: • What is the GPIO Expander Keypad and LCD Demo Board? • What the GPIO Expander Keypad and LCD Demo Board Kit includes 1.2 WHAT IS THE GPIO EXPANDER KEYPAD AND LCD DEMO BOARD? The GPIO Expander Keypad and LCD Demo Board allows the system designer to evaluate the operation of the MCP23X17 and MCP23X08 General Purpose I/O (GPIO) Expanders. The board demonstrates the GPIO Expanders’ performance in a keypad and LCD example. 1.3 WHAT THE GPIO EXPANDER KEYPAD AND LCD DEMO BOARD KIT INCLUDES This GPIO Expander Keypad and LCD Demo Board Kit includes: • One GPIO Expander Keypad and LCD Demo Board (102-00116) - MCP23008 GPIO Expander with I2C™ interface (installed) - MCP23S08 GPIO Expander with SPI interface (installed) - MCP23017 GPIO Expander with I2C™ interface (installed) - MCP23S17 GPIO Expander with SPI interface (installed) • Analog and Interface Products Demonstration Boards CD-ROM (DS21912) - GPIO Expander Keypad and LCD Demo Board User’s Guide (DS51636) - PIC® Microcontroller Firmware - PCB Gerber Files © 2006 Microchip Technology Inc. DS51636A-page 5 GPIO Expander Keypad and LCD Demo Board User’s Guide NOTES: DS51636A-page 6 © 2006 Microchip Technology Inc. GPIO EXPANDER KEYPAD AND LCD DEMO BOARD USER’S GUIDE Chapter 2. Installation and Operation 2.1 INTRODUCTION This chapter discusses the setup and operation of the GPIO Expander Keypad and LCD Demo Board. The GPIO Expander Keypad and LCD Demo Board is designed to demonstrate using GPIO expanders in a keypad and LCD example. The MCP23X17 interfaces to a 2x16 LCD module and the MCP23X08 interfaces to a 4x4 keyed matrix. Both the I2C™ and SPI versions are included on the board to demonstrate both serial interfaces. 2.2 FEATURES The GPIO Expander Keypad and LCD Demo Board has the following features: • Two (2) 8-bit GPIO Expanders - MCP23008 with I2C™ interface - MCP23S08 with SPI interface • Two (2) 16-bit GPIO Expanders - MCP23017 with I2C™ interface - MCP23S17 with SPI interface • 4X4 keypad layout (16 momentary buttons) - Numbers 0 - 9 - Six special function buttons • A 2X16 LCD module • Headers for the MCP23X08 and MCP23X17 pins • Header for programming the PIC18F4550 © 2006 Microchip Technology Inc. DS51636A-page 7 GPIO Expander Keypad and LCD Demo Board User’s Guide 2.3 GETTING STARTED The GPIO Expander Keypad and LCD Demo Board is a fully functional, assembled and tested board for demonstrating the MCP23008 and MCP23017 (I2C interface) and MCP23S08 and MCP23S17 (SPI interface) general purpose I/O expanders. The following describes the basic setup and operation (see Figure 2-1): 1. Either connect a 9V power supply into the power jack (J2) or connect a 5 V power supply to the VDD and GND test points. 2. The green power LED will illuminate. 3. The LCD will display the startup splash screen. 4. The appropriate LEDs (I2C or SPI) will illuminate to indicate the current serial mode. 5. Pressing buttons: - 0 - 9, #, *: will be reflected on the LCD - M: switches modes (I2C and SPI) to communicate with the MCP23X17 and MCP23X08; B: backspace; R: carriage return, and screen clear (2nd press); S: space FIGURE 2-1: BOARD LAYOUT 2 X 16 LCD Not Populated LED 9V EXT +5V PIC18F2550 MCP23008 LED LED LED ICSP USB MCP23S08 USB I2C/SPI MCP23017 MCP23S17 16-bit HEADER 8-bit HEADER GPIO Expander Keypad/LCD Demo GND M DS51636A-page 8 7 8 9 M 4 5 6 B 1 2 3 R * 0 # S © 2006 Microchip Technology Inc. Installation and Operation 2.4 GPIO EXPANDER KEYPAD AND LCD DEMO BOARD DESCRIPTION 2.4.1 Major Board Components The functional block diagram is shown in Figure 2-2. FIGURE 2-2: FUNCTIONAL BLOCK DIAGRAM Header Input Output IN GPIO OUT 2 X 16 LCD Control Power Programming 1. The GPIO BLOCK contains the MCP23X17 and MCP23X08 GPIO Expanders. Two (2) MCP23X17 devices are connected to the LCD module and two (2) MCP23X08 devices are connected to the keypad matrix. A button on the keypad toggles between I2C and SPI mode. When in I2C mode, the MCP23017 and MCP23008 are controlled by the PIC MCU. When in SPI mode, the MCP23S17 and MCP23S08 are controlled. Only one (1) MCP23X08 and one (1) MCP23X17 is on the bus at a time. 2. The CONTROL BLOCK contains the PIC18F4550 and is the main intelligence in the system. 3. The INPUT BLOCK contains the 4x4 keypad matrix. The MCP23X08 devices are used to scan the keys. 4. The OUTPUT BLOCK contains the 2x16 LCD. The MCP23X17 devices control the display. 5. The MCP23X17 and MCP23X08 I/O and serial lines are routed to the HEADER BLOCK to allow the pins to be probed. 6. The PROGRAMMING BLOCK contains the ICSP™ header for programming/debugging the PIC18F4550. 7. The POWER BLOCK contains the MCP1702 5V voltage regulator. The board can be powered by a 9V supply (connected through the power jack) or by applying 5V directly to the power points. © 2006 Microchip Technology Inc. DS51636A-page 9 GPIO Expander Keypad and LCD Demo Board User’s Guide 2.5 FIRMWARE DESCRIPTION See Figure 2-3 for the main firmware flow diagram. Main Function: 1. The firmware first configures the PIC MCU. 2. The MCP23X08 and MCP23X17 devices are configured. I2C Devices are selected first by default. The SPI devices I/O are held in reset. 3. The LCD splash screen is shown. 4. Wait for an interrupt from the MCP23X08. An interrupt will occur when a button is pressed. Four (4) inputs are configured to interrupt on falling edge. These inputs are for the “columns” of the keypad matrix. 5. After the interrupt occurs, the firmware calls the Scan_Buttons routine. 6. Then the Update_LCD routine. Scan_Buttons Function: 1. Read INTCAP register. This register contains a snapshot of the port condition when the interrupt occurred. 2. Swap inputs and outputs so the rows can be read. 3. Read GPIO register and merge with variable containing INTCAP value. 4. The pressed key is determined by looking up the result in a lookup table. Update_LCD Function: 1. The LCD is updated based on which button was pressed. DS51636A-page 10 © 2006 Microchip Technology Inc. Installation and Operation FIGURE 2-3: MAIN FIRMWARE FLOW Start Init_MCU Init_MCP Splash NO The MCP23X08 is configured to interrupt on falling edge for the columns (4 inputs) GPIO INT Flag Set? YES Scan_Buttons After the interrupt, the column location of the button is known and is contained in INTCAP. Need to read GPIO to get the Row location. Buttons: 0-9, #, * : Copied to the LCD M: Toggle mode (SPI and I2C™) B: Backspace R: Carriage Return S: Space Update_LCD © 2006 Microchip Technology Inc. DS51636A-page 11 GPIO Expander Keypad and LCD Demo Board User’s Guide FIGURE 2-4: KEYPAD SCAN Scan_Buttons Read INTCAP One nibble is set to input and the other nibble is output (to read the columns) (already configured before entering function). Read INTCAP and place in a variable. To read the rows. Swap inputs and outputs Merge with variable containing INTCAP value. The result can be looked up in a table (switch statement) to determine which key was pressed. Read GPIO Determine key press from lookup table Set I/O back to default so it is correct the next time the function is called END DS51636A-page 12 © 2006 Microchip Technology Inc. Installation and Operation FIGURE 2-5: LCD UPDATE Update_LCD The pressed button result comes from the variable in the Scan_Buttons function 1-9 # Button Press? M B S * R Display Backspace Toggle Serial Mode (I2C or SPI) Space Carriage Return Display # Display * END © 2006 Microchip Technology Inc. DS51636A-page 13 GPIO Expander Keypad and LCD Demo Board User’s Guide NOTES: DS51636A-page 14 © 2006 Microchip Technology Inc. GPIO EXPANDER KEYPAD AND LCD DEMO BOARD USER’S GUIDE Appendix A. Schematics and Board Layouts A.1 INTRODUCTION This appendix contains the schematic and PCB layout for the GPIO Expander Keypad and LCD Demo Board. Diagrams included: • Board Schematics - Pages 1 - 3. • Board - Top Layer (with silk screen) • Board - Bottom Layer © 2006 Microchip Technology Inc. DS51636A-page 15 GPIO Expander Keypad and LCD Demo Board User’s Guide BOARD SCHEMATIC - PAGE 1 M A.2 DS51636A-page 16 © 2006 Microchip Technology Inc. Schematics and Board Layouts BOARD SCHEMATIC - PAGE 2 M A.3 © 2006 Microchip Technology Inc. DS51636A-page 17 GPIO Expander Keypad and LCD Demo Board User’s Guide BOARD SCHEMATIC - PAGE 3 M A.4 DS51636A-page 18 © 2006 Microchip Technology Inc. Schematics and Board Layouts A.5 BOARD - TOP LAYER (WITH SILK SCREEN) A.6 BOARD - BOTTOM LAYER © 2006 Microchip Technology Inc. DS51636A-page 19 GPIO Expander Keypad and LCD Demo Board User’s Guide NOTES: DS51636A-page 20 © 2006 Microchip Technology Inc. GPIO EXPANDER KEYPAD AND LCD DEMO BOARD USER’S GUIDE Appendix B. Bill Of Materials (BOM) TABLE B-1: BILL OF MATERIALS Reference Designator Qty Description Manufacturer Part Number 23 C1, C5, C6 CAP 1UF 16V CERAMIC Y5V 0805 C15, C25, C30, C31, C32, C33, C34, C35, C36, C37, C38, C39, C40, C41, C42, C43, C44, C45, C46, C47, C48 Panasonic® - ECG ECJ-2VF1C105Z 1 C3 CAP CER .33UF 16V Y5V 0805 Murata Electronics® North America GRM219F51C334ZA01D 2 C16, C17 CAP 22PF 50V CERM CHIP 0805 SMD *Do Not Populate* Panasonic - ECG ECJ-2VC1H220J 1 C18 CAP .22UF 16V CERAMIC X7R 0805 Panasonic - ECG ECJ-2VB1C224K 4 D1, D2, D3, D4 LED 636NM SUPER RED 0805 SMD LITE-ON INC SML-LX0805SIC-TR 2 D5, D6 DIODE SCHOTTKY 20V 0.5A SOD123 ON Semiconductor® MBR0520LT1G 2 D7, D8 LED THIN 565NM GRN DIFF 0805 SMD Optoelectronics SML-LXT0805GW-TR 1 D9 RECT SCHOTTKY 1A 20V DO-214AA Micro Commercial Co. SMB5817-TP 4 EA Corner BUMPON X-TALL TAPER SQ .81X.30BK 3M/ESM SJ-5523 (BLACK) 1 J1 *Do Not Populate* — — 1 J2 CONN POWER JACK 2.5MM PCB CIRC CUI Inc PJ-102B 1 J3 *Do Not Populate* — — 1 J4 *Do Not Populate* — — 2 J5, J10 *Do Not Populate* — — 1 J9 CONN USB RTANG FEMALE TYPE B PCB *Do Not Populate* Assmann Electronics Inc AU-Y1007-R 1 LCD1 LCD_2x16 Fema CG1626-SGR1 6 R1, R2, R3, R8, R9, R53 RES 10.0K OHM 1/10W 1% 0805 SMD Panasonic - ECG ERJ-6ENF1002V 2 R4, R5 RES 270 OHM 1/8W 5% 0805 SMD Panasonic - ECG ERJ-6GEYJ271V 1 R6 RES 523 OHM 1/8W 1% 0805 SMD Yageo® 2 R7, R54 RES 4.70K OHM 1/8W 1% 0805 SMD Yageo Corporation RC0805FR-074K7L 3 R24, R25, R35 RES 1.00K OHM 1/10W 1% 0805 SMD Panasonic - ECG ERJ-6ENF1001V 2 R29, R30 Panasonic - ECG ERJ-6GEY0R00V Note 1: RES 0.0 OHM 1/8W 5% 0805 SMD Corporation RC0805FR-07523RL The components listed in this Bill of Materials are representative of the PCB assembly. The released BOM used in manufacturing uses all RoHS-compliant components. © 2006 Microchip Technology Inc. DS51636A-page 21 GPIO Expander Keypad and LCD Demo Board User’s Guide TABLE B-1: BILL OF MATERIALS (CONTINUED) Reference Designator Qty Description Manufacturer Part Number 16 R32, R33, R34, RES 100 OHM 1/10W 3900PPM R36, R37, R38, 5%0805 R39, R40, R41, R42, R43, R44, R45, R46, R47, R48 Panasonic - ECG 1 R49 RES 33.2K OHM 1/8W 1% 0805 SMD Yageo® Corporation RC0805FR-0733K2L 2 R50, R52 RES 475 OHM 1/10W 1% 0603 SMD Panasonic - ECG ERJ-3EKF4750V 1 R51 RES 100K OHM 1/8W 5% 0805 SMD Panasonic - ECG ERJ-6GEYJ104V 17 S11, S12, S13, SWITCH TACT 6MM SMD MOM 160GF Omron Electronics Inc S14, S15, S16, S17, S18, S19, S20, S21, S22, S23, S24, S25, S26, S27 1 TP1 TEST POINT PC MULTI PURPOSE BLK Keystone Electronics® 5011 1 TP2 TEST POINT PC MULTI PURPOSE RED Keystone Electronics 5010 1 U1 16 Bit I/O Expander with Serial Interface Microchip Technology Inc MCP23S17-E/SS 1 U2 8-Bit I/O Expander with SPI Interface Microchip Technology Inc MCP23S08-E/SS 1 U3 16 Bit I/O Expander with Serial Interface Microchip Technology Inc MCP23017-E/SS 1 U4 8-Bit I/O Expander with I2C Interface Microchip Technology Inc MCP23008-E/SS 1 U5 44-Pin, High-Performance, Enhanced Flash, USB Microcontroller Microchip Technology Inc PIC18F4550 1 U6 2 μA Low Dropout Positive Voltage Regulator Microchip Technology Inc MCP1702T-5002I/CB 1 U7 MOSFET P-CH 20V 850MA SSOT3 Fairchild Semiconductor® NDS352P 1 Y1 CRYSTAL 20.0000 MHZ SERIES RES *Do Not Populate* CTS-Frequency Controls ATS200 Note 1: ERA-S39J101V B3S-1000 The components listed in this Bill of Materials are representative of the PCB assembly. The released BOM used in manufacturing uses all RoHS-compliant components. DS51636A-page 22 © 2006 Microchip Technology Inc. Bill Of Materials (BOM) NOTES: © 2006 Microchip Technology Inc. DS51636A-page 23 WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Habour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-4182-8400 Fax: 91-80-4182-8422 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Alpharetta, GA Tel: 770-640-0034 Fax: 770-640-0307 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Korea - Gumi Tel: 82-54-473-4301 Fax: 82-54-473-4302 China - Fuzhou Tel: 86-591-8750-3506 Fax: 86-591-8750-3521 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Malaysia - Penang Tel: 60-4-646-8870 Fax: 60-4-646-5086 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Taiwan - Hsin Chu Tel: 886-3-572-9526 Fax: 886-3-572-6459 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 China - Shunde Tel: 86-757-2839-5507 Fax: 86-757-2839-5571 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Xian Tel: 86-29-8833-7250 Fax: 86-29-8833-7256 10/19/06 DS51636A-page 24 © 2006 Microchip Technology Inc.