UM3483E/UM3486E 3V to 5.5V-Powered, ±15kV ESD-Protected, Slew-Rate-Limited, True RS-485 Transceivers UM3483E/UM3486E SOP8/DIP8 General Description The UM3483E, UM3486E are 3V to 5.5V-powered, ±15kV ESD-protected, slew-rate-limited differential transceivers which provide full RS485 compatibility. Each part contains one driver and one receiver, which is designed for data transmission with extended common mode range (-7V to 12V). The UM3483E features slew-rate-limited driver which minimizes EMI and reduces reflections resulted from improperly terminated cables. The UM3483E allows up to 500kbps error-free data transmission, while the partially slew-rate-limited UM3486E transmits at data rates up to 2.5Mbps. The UM3483E, UM3486E also feature enhanced electrostatic discharge (ESD) protection. All of the transmitter outputs and receiver inputs are protected to ±15kV using IEC61000-4-2 Air-Gap Discharge, ±15kV using the Human Body Model and ±8kV using IEC61000-4-2 Contact Discharge. Drivers are short-circuit current limited. When the driver outputs are placed into a high-impedance state by thermal shutdown circuitry, drivers are protected against excessive power dissipation. And the fail-safe feature of the receiver input guarantees a logic-high output if both inputs are open, shorted or idle. Both parts have power up/down mode, the glitch-free driver outputs permit live insertion or removal of the transceiver into/from the data bus. The CMOS design offers significant power savings without sacrificing ruggedness against overload or ESD damage. The typical quiescent current is only 300μA during operation and 1μA in shutdown mode. The UM3483E, UM3486E are intended for half-duplex communication and are available in SOP8 and DIP8 packages. Applications Features Telecommunications Low-Power RS-485 Transceivers Integrated Services Digital Networks Industrial-Control Local Area Networks Transceivers for EMI-Sensitive Applications Packet Switching Level Translators ESD Protection for RS-485 I/O Pins ±15kV—Human Body Model ±15kV—IEC61000-4-2, Air-Gap Discharge ±8kV—IEC61000-4-2, Contact Discharge 3V to 5.5V Supply Voltage Range Enhanced Slew-Rate Limiting Facilitates Error-Free Data Transmission 1μA Low-Current Shutdown Mode -7V to +12V Common-Mode Input Voltage Range Allows up to 256 Transceivers on the Bus Thermal Shutdown Current-Limiting for Driver Overload Protection ________________________________________________________________________ http://www.union-ic.com Rev.04 Sep.2015 1/18 UM3483E/UM3486E Ordering Information Part Number UM3483EESA UM3483EEPA UM3486EESA UM3486EEPA Operating Temperature -40°C to +85°C -40°C to +85°C -40°C to +85°C -40°C to +85°C Mark Code UM3483EESA UM3483EEPA UM3486EESA UM3486EEPA Package Type SOP8 DIP8 SOP8 DIP8 Selection Guide Part Number UM3483E UM3486E Guaranteed Date Rate (Mbps) 0.5 2.5 Low-Power Shutdown Slew-Rate Limited Yes Yes Yes Yes Pin Configurations Driver/ Receiver Enable Yes Yes Shutdown Current (μA) 1 1 Transceivers On Bus 256 256 ±15kV ESD Protection Yes Yes Top View RO 1 8 VCC RE 2 7 B DE 3 6 A DI 4 5 GND RO 1 8 VCC RE 2 7 B DE 3 6 A DI 4 5 GND UM3483 EESA XX UM3486 EESA XX XX: Week Code UM3483EESA SOP8 XX: Week Code UM3486EESA SOP8 UM3483 EEPA XX UM3486 EEPA XX XX: Week Code UM3483EEPA DIP8 XX: Week Code UM3486EEPA DIP8 ________________________________________________________________________ http://www.union-ic.com Rev.04 Sep.2015 2/18 UM3483E/UM3486E Absolute Maximum Ratings Symbol VCC PD TA TSTG TL Parameter Supply Voltage Value +7 Unit V Control Input Voltage (/RE, DE) -0.3V to (VCC + 0.3V) V Driver Input Voltage (DI) -0.3V to (VCC + 0.3V) V Driver Output Voltage (A, B) -7 to +12 V Receiver Input Voltage (A, B) -7 to +12 V Receiver Output Voltage (RO) -0.3V to (VCC + 0.3V) V Continuous Power Dissipation at TA = 70°C DIP8 727 SOP8 471 -40 to +85 -65 to +160 +300 Ambient Temperature Storage Temperature Range Lead Temperature for Soldering 10 seconds mW °C °C °C DC Electrical Characteristics (VCC = +3V to 5.5V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) Parameter SUPPLY CURRENT Supply Current Supply Current in Shutdown Mode LOGIC Input High Voltage Input Low Voltage Logic Input Current Driver Symbol ICC ISHDN VIH VIL IIN1 Test Conditions DE=VCC, No load, DI = GND /RE=0V or VCC or VCC DE=0V, /RE=0V DE, DI, /RE DE, DI, /RE DE, DI, /RE VOD RL=54Ω Figure 1 RL=60Ω Figure 1 Change in Magnitude of Driver Differential Output Voltage for Complementary Output States (Note 1) Driver Common-Mode Output Voltage Change in Magnitude of Common-Mode Output Voltage (Note 1) Driver Short-Circuit Output Current VCC=3.3V VCC=5V VCC=3.3V VCC=5V VCC=3.3V VCC=5V Typ Max 0.15 1 0.15 1 Unit mA DE=0V, /RE=VCC, DI=VCC or 0V No Load Figure 1 Differential Driver Output Min 1 µA 0.8 1 V V µA 2.0 3.3 5 1.2 1.5 1.3 1.5 V ΔVOD RL=54Ω or 100Ω, Figure 1 0.2 V VOC RL=54Ω or 100Ω, Figure 1 3 V ΔVOC RL=54Ω or 100Ω, Figure 1 0.2 V IOSD VOUT = -7V VOUT = 12V -250 +250 mA ________________________________________________________________________ http://www.union-ic.com Rev.04 Sep.2015 3/18 UM3483E/UM3486E DC Electrical Characteristics (Continued) (VCC = +3V to 5.5V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) Parameter Symbol Test Conditions Min Typ -0.2 -0.05 Max Unit RECEIVER Receiver Differential Threshold Voltage VTH -7V≤VCM≤12V Receiver Input Hysteresis ΔVTH VCM=0V Receiver Input Resistance RIN -7V≤VCM≤12V Input Current (A, B) IIN2 DE=0V, VCC=0V or +3V to 5.5V 0.2 25 V mV 96 kΩ VIN = 12V 1 VIN = -7V -0.8 mA Receiver Output High Voltage VOH IOUT=-1.5mA, VID=200mV, Figure 2 Receiver Output Low Voltage VOL IOUT=2.5mA, VID=200mV, Figure 2 0.4 V Three-State (High Impedance) Output Current at Receiver IOZR 0V≤VOUT≤VCC 1 µA Receiver Short-Circuit Output Current IOSR 0V≤VRO≤VCC ±60 mA Vcc-1.5 V ±20 ESD Protection ESD Protection for A, B Human Body Model IEC61000-4-2 Air Discharge ±15 ±15 IEC61000-4-2 Contact Discharge ±8 kV ________________________________________________________________________ http://www.union-ic.com Rev.04 Sep.2015 4/18 UM3483E/UM3486E Driver Switching Characteristics (UM3483E) (VCC = +3V to 5.5V, TA = +25°C.) Parameter Symbol Maximum Data Rate fMAX Driver Differential Output Delay tDD RL=60Ω, Figure 3 250 500 1000 ns tTD RL=60Ω, Figure 3 250 500 750 ns tPLH RL=27Ω, Figure 4 250 550 1000 ns tPHL RL=27Ω, Figure 4 250 550 1000 ns tPDS RL=27Ω, Figure 4 10 30 ns Driver Output Enable Time to Low Level tPZL RL=110Ω, Figure 6 100 2500 ns Driver Output Enable Time to High Level tPZH RL=110Ω, Figure 5 100 2500 ns tPHZ RL=110Ω, Figure 5 100 100 ns tPLZ RL=110Ω, Figure 6 100 100 ns tPSL RL=110Ω, Figure 6 500 2500 ns tPSH RL=110Ω, Figure 5 500 2500 ns Typ Max Unit Driver Differential Output Transition Time Driver Propagation Delay, Low-to-High Level Driver Propagation Delay, High-to-Low Level | tPLH – tPHL | Driver Propagation Delay Skew (Note 2) Test Conditions Min Typ Max 500 Unit kbps Driver-Output Enable/Disable Times Driver Output Disable Time from High Level Driver Output Disable Time from Low Level Driver Output Enable Time from Shutdown to Low Level Driver Output Enable Time from Shutdown to High Level Driver Switching Characteristics (UM3486E) (VCC = +3V to 5.5V, TA = +25°C.) Parameter Symbol Maximum Data Rate fMAX Driver Differential Output Delay tDD RL=60Ω, Figure 3 20 50 100 ns tTD RL=60Ω, Figure 3 20 50 100 ns tPLH RL=27Ω, Figure 4 25 55 100 ns tPHL RL=27Ω, Figure 4 25 55 100 ns tPDS RL=27Ω, Figure 4 2 10 ns Driver Output Enable Time to Low Level tPZL RL=110Ω, Figure 6 60 100 ns Driver Output Enable Time to High Level tPZH RL=110Ω, Figure 5 60 100 ns tPHZ RL=110Ω, Figure 5 60 100 ns tPLZ RL=110Ω, Figure 6 60 100 ns tPSL RL=110Ω, Figure 6 500 800 ns tPSH RL=110Ω, Figure 5 500 800 ns Driver Differential Output Transition Time Driver Propagation Delay, Low-to-High Level Driver Propagation Delay, High-to-Low Level | tPLH – tPHL | Driver Propagation Delay Skew (Note 2) Test Conditions Min 2500 kbps Driver-Output Enable/Disable Times Driver Output Disable Time from High Level Driver Output Disable Time from Low Level Driver Output Enable Time from Shutdown to Low Level Driver Output Enable Time from Shutdown to High Level ________________________________________________________________________ http://www.union-ic.com Rev.04 Sep.2015 5/18 UM3483E/UM3486E Receiver Switching Characteristics (VCC = +3V to 5.5V, TA = +25°C.) Parameter Symbol Time to Shutdown tSHDN Receiver Propagation Delay, Low-to-High Level tRPLH Receiver Propagation Delay, High-to-Low Level tRPHL | tRPLH – tRPHL | Receiver Propagation Delay Skew tRPDS Receiver Output Enable Time to Low Level Receiver Output Enable Time to High Level Receiver Output Disable Time from High Level Receiver Output Disable Time from Low Level Receiver Output Enable Time from Shutdown to Low Level Receiver Output Enable Time from Shutdown to High Level tPRZL tPRZH tPRHZ tPRLZ tPRSL tPRSH Test Conditions UM3483E/UM3486E (Note 3) VID=0 to 3.0V, C L=15pF, Figure 7 UM3483E VID=0 to 3.0V, C L=15pF, Figure 7 UM3483E VID=0 to 3.0V, C L=15pF, Figure 7 UM3483E CL=15pF, Figure 8, UM3483E/UM3486E CL=15pF, Figure 8, UM3483E/UM3486E CL=15pF, Figure 8, UM3483E/UM3486E CL=15pF, Figure 8, UM3483E/UM3486E CL=15pF, Figure 8, UM3483E/UM3486E CL=15pF, Figure 8, UM3483E/UM3486E Min Typ Max Unit 50 200 600 ns 100 200 ns 100 200 ns 30 ns 20 100 ns 20 100 ns 30 200 ns 30 200 ns 20 100 ns 20 100 ns Note 1: ΔVOD and ΔVOC are the changes in VOD and VOC, respectively, when the DI input changes state. Note 2: Measured on | tPLH (A)– tPHL (A)| and | tPLH (B)– tPHL (B)|. Note 3: The transceivers are put into shutdown by bringing /RE high and DE low. If the inputs are in this state for less than 80ns, the parts are guaranteed not to enter shutdown. If the inputs are in this state for at least 300ns, the parts are guaranteed to have entered shutdown. See Low-Power Shutdown Mode section. ________________________________________________________________________ http://www.union-ic.com Rev.04 Sep.2015 6/18 UM3483E/UM3486E Typical Operating Characteristics (VCC=+3.3V, TA=+25ºC, unless otherwise noted.) Supply Current vs. Temperature DE=1, /RE=0, DI=1 Supply Current vs. Temperature DE=1, /RE=0, DI=0 Output Current vs. Receiver Output High Voltage Output Current vs. Receiver Output Low Voltage Receiver Output High Voltage vs. Temperature Receiver Output Low Voltage vs. Temperature Driver Differential Output Voltage vs. Temperature DI=1 Driver Differential Output Voltage vs. Temperature DI=0 ________________________________________________________________________ http://www.union-ic.com Rev.04 Sep.2015 7/18 UM3483E/UM3486E Typical Operating Characteristics (Continued) (VCC=+3.3V, TA=+25ºC, unless otherwise noted.) Differential Output Current vs. Differential Output Voltage Shutdown Current vs. Temperature A B Short-Circuit Current vs. Temperature DI=1 A B Short-Circuit Current vs. Temperature DI=0 RO Short-Circuit Current vs. Temperature R0=1 RO Short-Circuit Current vs. Temperature R0=0 ________________________________________________________________________ http://www.union-ic.com Rev.04 Sep.2015 8/18 UM3483E/UM3486E Typical Operating Characteristics (Continued) (VCC=+5.0V, TA=+25ºC, unless otherwise noted.) Supply Current vs. Temperature DE=1, /RE=0, DI=1 Output Current vs. Receiver Output High Voltage Supply Current vs. Temperature DE=1, /RE=0, DI=0 Output Current vs. Receiver Output Low Voltage Receiver Output High Voltage vs. Temperature Receiver Output Low Voltage vs. Temperature Driver Differential Output Voltage vs. Temperature DI=1, RL=54Ω Driver Differential Output Voltage vs. Temperature DI=0, RL=54Ω ________________________________________________________________________ http://www.union-ic.com Rev.04 Sep.2015 9/18 UM3483E/UM3486E Typical Operating Characteristics (Continued) (VCC=+5.0V, TA=+25ºC, unless otherwise noted.) Differential Output Current vs. Differential Output Voltage Shutdown Current vs. Temperature A B Short-Circuit Current vs. Temperature DI=1 A B Short-Circuit Current vs. Temperature DI=0 RO Short-Circuit Current vs. Temperature R0=1 RO Short-Circuit Current vs. Temperature R0=0 ________________________________________________________________________ http://www.union-ic.com Rev.04 Sep.2015 10/18 UM3483E/UM3486E Pin Description Pin Number Symbol Function 1 RO Receiver Output. If A＞B by -50mV, RO will be high; if A＜B by 200mV, RO will be low. ______ 2 ______ RE Receiver Output Enable. RO is enabled when RE is low; RO is ______ ______ high impedance when RE is high. Drive RE high and DE low to enter low-power shutdown mode. Driver Output Enable. The driver outputs are enabled by bringing ______ 3 DE DE high. They are high impedance when DE is low. If RE is high and DE is low, the device will enter a low-power shutdown mode. If the driver outputs are enabled, the parts function as line drivers. While they are high impedance, they function as line receivers if ______ RE is low. Driver Input. A low on DI forces output A low and output B high. Similarly, a high on DI forces output A high and output B low. Ground 4 DI 5 GND 6 A Non-inverting Receiver Input and Non-inverting Driver Output 7 B Inverting Receiver Input and Inverting Driver Output. 8 VCC Positive Supply: 3.0V≤VCC≤5.5V RS-485 Communication Function Table Table1. Transmitting INPUTS OUTPUTS DE DI B A RE X 1 1 0 1 X 1 0 1 0 0 0 X High-Z High-Z 1 0 X High-Z High-Z X=Don’t care; High-Z=High impedance ______ MODE Normal Normal Normal Shutdown Table2. Receiving INPUTS DE A, B RE 0 X >-50mV 0 X <-200mV 0 X Inputs Open 1 0 X X=Don’t care; High-Z=High impedance ______ OUTPUTS RO 1 0 1 High-Z MODE Normal Normal Normal Shutdown ________________________________________________________________________ http://www.union-ic.com Rev.04 Sep.2015 11/18 UM3483E/UM3486E Test Circuit RL 2 VID R VOD D 0 RL 2 VCC VOC VOL Figure 1. Driver VOD and VOC VOH IOL (+) IOH (-) Figure 2. Receiver VOH and VOL 3V 1.5V IN 1.5V CL 0 OUT D GENERATOR (NOTE 4) tDD tDD RL 60Ω 50Ω 90% VCC 50% 50% OUT CL ≈2.0V 90% 10% 10% ≈-2.0V CL=15pF (NOTE 5) tTD tTD Figure 3. Driver Differential Output Delay and Transition Times 3V VOM IN 1.5V 1.5V RL 27Ω 0V S1 OUT D GENERATOR (NOTE 4) tPHL tPLH VOH 50Ω CL=15pF (NOTE 5) A OUT VOM VOM VCC VOL V OM tPLH tPHL V OH V OL 2 VOH B OUT VOM VOM VOL Figure 4. Driver Propagation Times 3V S1 0 OR 3V OUT D IN 1.5V 1.5V 0 RL 110Ω CL=50pF (NOTE 5) GENERATOR (NOTE 4) tPHZ tPZH 50Ω 0.25V OUT V OM V V OL OH 2 VOH VOM 0 Figure 5. Driver Enable and Disable Times (tPZH, tPSH, tPHZ) ________________________________________________________________________ http://www.union-ic.com Rev.04 Sep.2015 12/18 UM3483E/UM3486E VCC 3V RL 110Ω S1 0 OR 3V IN 1.5V 1.5V 0 OUT D tPLZ tPSL CL=50pF (NOTE 5) GENERATOR (NOTE 4) VCC OUT VOM 50Ω 0.25V VOL Figure 6. Driver Enable and Disable Times (tPZL, tPSL, tPLZ) 3.0V VID GENERATOR (NOTE 4) OUT R IN 50Ω 1.5V 1.5V CL=15pF (NOTE 5) 0 tRPHL tRPLH VCC 1.5V VOM OUT VOM 0 VOM VCC 2 0 Figure 7. Receiver Propagation Delay S1 S3 1.5V 1k -1.5V VID VCC R S2 CL (NOTE 5) GENERATOR (NOTE 4) 50Ω 3V IN 3V S1 OPEN S2 CLOSED S3=1.5V 1.5V IN 1.5V 0 0 tPRZH tPRSH tPRZL tPRSL VOH OUT VCC OUT 1.5V 1.5V 0 VOL 3V 3V IN S1 OPEN S2 CLOSED S3=1.5V 1.5V IN S1 CLOSED S2 OPEN S3=-1.5V 1.5V 0 0 tPRHZ OUT 0.25V S1 CLOSED S2 OPEN S3=-1.5V tPRLZ VOH VCC OUT 0 0.25V VOL Figure 8. Receiver Enable and Disable Times Note 4: The input pulse is supplied by a generator with the following characteristics: f=250kHz, 50% duty cycle, tr≤6.0ns, zo=50Ω. Note 5: CL includes probe and stray capacitance. ________________________________________________________________________ http://www.union-ic.com Rev.04 Sep.2015 13/18 UM3483E/UM3486E Typical Operating Circuit 120ohm 120ohm DI DE B B D D DI DE RO A B A B A A R R RO RE RE Master Node R R D DI D DE RO RE Slave Node 1 DI DE Terminal Slave Node RO RE Slave Node N Figure 9. Typical Half-Duplex RS-485 Network Detail Description The UM3483E, UM3486E are low-power transceivers for RS-485 communications. The UM3483E can transmit and receive at data rates up to 500kbps, and the UM3486E at up to 2.5Mbps. The UM3483E, UM3486E are half-duplex. Driver Enable (DE) and Receiver Enable ______ (R E ) pins are included on the UM3483E, UM3486E. When disabled, the driver and receiver outputs are high impedance. Fail-Safe The UM3483E, UM3486E guarantees a logic-high receiver output when the receiver inputs are shorted or open, or when they are connected to a terminated transmission line with all drivers disabled. This is done by setting the receiver threshold between -50mV and -200mV. If the differential receiver input voltage (A-B) is greater than or equal to -50mV, RO is logic high. If A-B is less than or equal to -200mV, RO is logic low. In the case of a terminated bus with all transmitters disabled, the receiver’s differential input voltage is pulled to 0V by the termination. With the receiver thresholds of the UM3483E, UM3486E, this results in a logic high with a 50mV minimum noise margin. Unlike previous fail-safe devices, the -50mV to -200mV threshold complies with the ±200mV EIA/TIA-485 standard. ±15kV ESD Protection As with all Union devices, ESD-protection structures are incorporated on all pins to protect against electrostatic discharges encountered during handling and assembly. The driver outputs and receiver inputs of the UM3483E, UM3486E have extra protection against static electricity. Union’s engineers have developed state-of-the-art structures to protect these pins against ESD of ±15kV without damage. The ESD-protected pins are tested with reference to the ground pin in a power-down condition. They are tested to ±15kV using the Human Body Model. Applications Information 256 Transceivers on the Bus The standard RS-485 receiver input impedance is 12kΩ (one unit load), and the standard driver can drive up to 32 unit loads. The Union family of transceivers have a 1/8 unit load receiver input impedance (96kΩ), allowing up to 256 transceivers to be connected in parallel on one communication line. Any combination of these devices and/or other RS-485 transceivers with a total of 32 unit loads or less can be connected to the line. ________________________________________________________________________ http://www.union-ic.com Rev.04 Sep.2015 14/18 UM3483E/UM3486E Reduced EMI and Reflections The UM3483E, UM3486E are slew-rate-limited, minimizing EMI and reducing reflections caused by improperly terminated cables. In general, a transmitter’s rise time relates directly to the length of an unterminated stub, which can be driven with only minor waveform reflections. The following equation expresses this relationship conservatively: Length=tRISE/(10×1.5ns/ft) Where tRISE is the transmitter’s rise time. A system can work well with longer unterminated stubs, even with severe reflections, if the waveform settles out before the UART samples them. Low-Power Shutdown Mode ______ Low-power shutdown mode is initiated by bringing both R E high and DE low. In shutdown, the ______ device typically draws only 1μA of supply current. R E and DE may be driven simultaneously; ______ the parts are guaranteed not to enter shutdown if R E is high and DE is low for less than 50ns. If the inputs are in this state for at least 600ns, the parts are guaranteed to enter shutdown. Enable times tPZH and tPZL in the Switching Characteristics tables assume the part was not in a low-power shutdown state. Enable times tPSH and tPSL assume the parts were shut down. It takes drivers and receivers longer to become enabled from low-power shutdown mode (tPSH, tPSL) than from driver/receiver-disable mode (tPZH, tPZL). Driver Output Protection Two mechanisms prevent excessive output current and power dissipation caused by faults or bus contention. First, a foldback current limit on the output stage, provides immediate protection against short circuits over the whole common-mode voltage range. Second, a thermal shutdown circuit, forces the driver outputs into a high-impedance state if the die temperature becomes excessive. Propagation Delay Skew time is simply the difference between the low-to-high and high-to-low propagation delay. Small driver/receiver skew times help maintain a symmetrical mark-space ratio (50% duty cycle). The receiver skew time, |tRPLH - tRPHL|, is under 10ns (20ns for the UM3483E). The driver skew times 12ns for the UM3486E, and typically under 50ns for the UM3483E. Typical Applications The UM3483E, UM3486E transceivers are designed for bidirectional data communications on multipoint bus transmission lines. To minimize reflections, the line should be terminated at both ends in its characteristic impedance, and stub lengths of the main line should be kept as short as possible. The slew-rate-limited UM3483E and the partially slew-rate-limited UM3486E are more tolerant of imperfect termination. ________________________________________________________________________ http://www.union-ic.com Rev.04 Sep.2015 15/18 UM3483E/UM3486E Package Information SOP8 Outline Drawing c L D E E1 Symbol 1 2 θ e Top View A A2 End View A1 b Side View A A1 A2 b c D E E1 e L θ DIMENSIONS MILLIMETERS INCHES Min Max Min Max 1.350 1.750 0.053 0.069 0.100 0.250 0.004 0.010 1.350 1.550 0.053 0.061 0.33 0.51 0.013 0.020 0.170 0.250 0.006 0.010 4.700 5.100 0.185 0.200 3.800 4.000 0.150 0.157 5.800 6.200 0.228 0.244 1.270 (BSC) 0.050 (BSC) 0.400 1.270 0.016 0.050 0° 8° 0° 8° 4.95 1.30 Land Pattern 1.27 0.50 NOTES: 1. Compound dimension: 4.90×3.90 ; 2. Unit: mm; 3. General tolerance ±0.05mm unless otherwise specified; 4. The layout is just for reference. Tape and Reel Orientation XXXXXX XXXX XX ________________________________________________________________________ http://www.union-ic.com Rev.04 Sep.2015 16/18 UM3483E/UM3486E DIP8 Outline Drawing D1 E E1 eA C D A1 L A3 A2 A eB b1 e b DIMENSIONS MILLIMETERS INCHES Symbol Min Max Min Max A 5.08 0.200 A1 0.38 0.015 A2 3.18 4.45 0.125 0.175 A3 1.40 2.03 0.055 0.080 b 0.41 0.56 0.016 0.022 b1 1.14 1.65 0.045 0.065 C 0.20 0.30 0.008 0.012 D 8.84 9.91 0.348 0.390 D1 0.13 2.03 0.005 0.080 E 7.62 8.26 0.300 0.325 E1 6.10 7.87 0.240 0.310 e 2.54 0.100 eA 7.62 0.300 eB 10.16 0.400 L 2.92 3.81 0.115 0.150 ________________________________________________________________________ http://www.union-ic.com Rev.04 Sep.2015 17/18 UM3483E/UM3486E GREEN COMPLIANCE Union Semiconductor is committed to environmental excellence in all aspects of its operations including meeting or exceeding regulatory requirements with respect to the use of hazardous substances. Numerous successful programs have been implemented to reduce the use of hazardous substances and/or emissions. All Union components are compliant with the RoHS directive, which helps to support customers in their compliance with environmental directives. For more green compliance information, please visit: http://www.union-ic.com/index.aspx?cat_code=RoHSDeclaration IMPORTANT NOTICE The information in this document has been carefully reviewed and is believed to be accurate. Nonetheless, this document is subject to change without notice. Union assumes no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update or to keep current the contained information, or to notify a person or organization of any update. Union reserves the right to make changes, at any time, in order to improve reliability, function or design and to attempt to supply the best product possible. Union Semiconductor, Inc Add: Unit 606, No.570 Shengxia Road, Shanghai 201210 Tel: 021-51093966 Fax: 021-51026018 Website: www.union-ic.com ________________________________________________________________________ http://www.union-ic.com Rev.04 Sep.2015 18/18