ISL43L410 ® Data Sheet July 28, 2006 Ultra Low ON-Resistance, Low Voltage, Single Supply, DPDT Analog Switch The Intersil ISL43L410 device is a low ON-resistance, low voltage, bidirectional, double-pole/double-throw (DPDT) analog switch designed to operate from a single +1.65V to +3.6V supply. It is equipped with an inhibit pin to simultaneously open all signal paths. Targeted applications include battery powered equipment that benefit from low RON (0.25Ω) and fast switching speeds (tON = 12ns, tOFF = 5ns). The digital logic input is 1.8V logiccompatible when using a single +3V supply. Cell phones, for example, often face ASIC functionality limitations. The number of analog input or GPIO pins may be limited and digital geometries are not well suited to analog switch performance. This part may be used to “mux-in” additional functionality while reducing ASIC design risk. The ISL43L410 is offered in small form factor packages, alleviating board space limitations. The ISL43L410 is a committed double-pole/double-throw (DPDT) that consists of two normally open (NO) and two normally closed (NC) switches. This configuration is perfect for use in differential 2-to-1 multiplexer applications. FN6090.2 Features • Pb-Free Plus Anneal Available (RoHS Compliant) (see Ordering Info) • ON Resistance (RON) - V+ = +3.0V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.25Ω - V+ = +1.8V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.4Ω • RON Matching Between Channels . . . . . . . . . . . . . . . .0.03Ω • RON Flatness Across Signal Range . . . . . . . . . . . . . . .0.03Ω • Single Supply Operation. . . . . . . . . . . . . . . . +1.65V to +3.6V • Low Power Consumption (PD) . . . . . . . . . . . . . . . . . . <0.2µW • Fast Switching Action (V+ = +2.7V) - tON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12ns - tOFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5ns • ESD HBM Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >9kV • Guaranteed Break-before-Make • 1.8V Logic Compatible (+3V supply) • Available in 10 Ld 3x3 thin DFN and 10 Ld MSOP Packages Applications TABLE 1. FEATURES AT A GLANCE • Battery powered, Handheld, and Portable Equipment - Cellular/mobile Phones - Pagers - Laptops, Notebooks, Palmtops ISL43L410 Number of Switches 2 SW DPDT 3V RON 0.25Ω 3V tON/tOFF 12ns/5ns 1.8V RON 0.4Ω 1.8V tON/tOFF 20ns/8ns Packages 10Ld 3x3 thin DFN, 10Ld MSOP • Portable Test and Measurement • Medical Equipment • Audio and Video Switching Related Literature • Technical Brief TB363 “Guidelines for Handling and Processing Moisture Sensitive Surface Mount Devices (SMDs)” • Application Note AN557 “Recommended Test Procedures for Analog Switches” 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2004, 2006. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL43L410 Pinout Truth Table (Note 1) ISL43L410 (TDFN, MSOP) TOP VIEW INH ADD SWITCH ON 1 X NONE 0 0 NCX 0 1 NOX 10 NO2 V+ 1 9 COM2 NO1 2 COM1 3 8 INH ADD 4 7 NC2 NC1 5 6 GND NOTE: Logic “0” ≤0.5V. Logic “1” ≥1.4V with a 3V supply. Pin Descriptions PIN LOGIC V+ NOTE: 1. Switches Shown for Logic “0” Input. FUNCTION System Power Supply Input (+1.65V to +3.6V) GND Ground Connection INH Digital Control Input. Connect to GND for Normal Operation. Connect to V+ to turn all switches off. ADD Address Input Pin COM Analog Switch Common Pin NO Analog Switch Normally Open Pin NC Analog Switch Normally Closed Pin Ordering Information PART NUMBER PART MARKING TEMP. RANGE (°C) PACKAGE PKG. DWG. # ISL43L410IR L40 -40 to 85 10 Ld 3x3 thin DFN L10.3x3A ISL43L410IR-T L40 -40 to 85 10 Ld 3x3 thin DFN Tape and Reel L10.3x3A ISL43L410IU L410 -40 to 85 10 Ld MSOP M10.118 ISL43L410IU-T L410 -40 to 85 10 Ld MSOP Tape and Reel M10.118 ISL43L410IRZ (See Note) L40Z -40 to 85 10 Ld 3x3 thin DFN (Pb-free) L10.3x3A ISL43L410IRZ-T (See Note) L40Z -40 to 85 10 Ld 3x3 thin DFN Tape and Reel (Pb-free) L10.3x3A ISL43L410IUZ (See Note) L410Z -40 to 85 10 Ld MSOP (Pb-free) M10.118 ISL43L410IUZ-T (See Note) L410Z -40 to 85 10 Ld MSOP Tape and Reel (Pb-free) M10.118 NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 2 FN6090.2 July 28, 2006 ISL43L410 Absolute Maximum Ratings Thermal Information V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 4.7V Input Voltages NO, NC, ADD, INH (Note 2) . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V) Output Voltages COM (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V) Continuous Current NO, NC, or COM . . . . . . . . . . . . . . . . . ±300mA Peak Current NO, NC, or COM (Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . ±500mA ESD Rating: HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>9kV MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>500V CDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>1kV Thermal Resistance (Typical, Note 3) θJA (°C/W) 10 Ld 3x3 DFN Package . . . . . . . . . . . . . . . . . . . . . 110 10 Ld MSOP Package . . . . . . . . . . . . . . . . . . . . . . . 190 Maximum Junction Temperature (Plastic Package). . . . . . . . 150°C Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to 150°C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C (Lead Tips Only) Operating Conditions Temperature Range ISL43L410IX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 2. Signals on NC, NO, ADD, INH, or COM exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings. 3. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details. Electrical Specifications - 3V Supply PARAMETER Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, VINH = 1.4V, VINL = 0.5V (Note 4, 6), Unless Otherwise Specified TEST CONDITIONS TEMP (°C) (NOTE 5) MIN Full 0 - V+ V 25 - 0.29 0.4 Ω Full - - 0.4 Ω 25 - 0.03 0.06 Ω TYP (NOTE 5) MAX UNITS ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG ON Resistance, RON V+ = 2.7V, ICOM = 100mA, VNO or VNC = 0V to V+, See Figure 5 RON Matching Between Channels, ∆RON V+ = 2.7V, ICOM = 100mA, VNO or VNC= Voltage at max RON, Note 9 RON Flatness, RFLAT(ON) V+ = 2.7V, ICOM = 100mA, VNO or VNC = 0V to V+, Note 7 NO or NC OFF Leakage Current, INO(OFF) or INC(OFF) V+ = 3.3V, VCOM = 0.3V, 3V, VNO or VNC = 3V, 0.3V COM ON Leakage Current, ICOM(ON) V+ = 3.3V, VCOM = 0.3V, 3V, or VNO or VNC = 0.3V, 3V Full - - 0.06 Ω 25 - 0.03 0.1 Ω Full - - 0.1 Ω nA 25 -2 - 2 Full -40 - 40 nA 25 -3 - 3 nA Full -60 - 60 nA ns DYNAMIC CHARACTERISTICS Turn-ON Time, tON V+ = 2.7V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF, See Figure 1, Note 8 25 - 14 20 Full - - 25 ns 25 - 6 12 ns Turn-OFF Time, tOFF V+ = 2.7V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF, See Figure 1, Note 8 Full - - 17 ns Break-Before-Make Time Delay, tD V+ = 3.3V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF, See Figure 3, Note 8 Full 2 7 - ns Charge Injection, Q CL = 1.0nF, VG = 0V, RG = 0Ω, See Figure 2 25 - 95 - pC OFF Isolation RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1VRMS, See Figure 4 25 - 68 - dB Crosstalk (Channel-to-Channel) RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1VRMS, See Figure 6 25 - -95 - dB Total Harmonic Distortion f = 20Hz to 20kHz, VCOM = 2VP-P, RL = 600Ω 25 - 0.003 - % NO or NC OFF Capacitance, COFF f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7 25 - 115 - pF COM ON Capacitance, CCOM(ON) 25 - 224 - pF 3 f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7 FN6090.2 July 28, 2006 ISL43L410 Electrical Specifications - 3V Supply PARAMETER Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, VINH = 1.4V, VINL = 0.5V (Note 4, 6), Unless Otherwise Specified (Continued) TEST CONDITIONS TEMP (°C) (NOTE 5) MIN Full 1.65 3.6 V 25 - - 40 nA Full - - 750 nA Full - - 0.5 V Full 1.4 - - V Full -0.5 - 0.5 µA TYP (NOTE 5) MAX UNITS POWER SUPPLY CHARACTERISTICS Power Supply Range Positive Supply Current, I+ V+ = +1.65 to 3.6V, VIN = 0V or V+ DIGITAL INPUT CHARACTERISTICS Input Voltage Low, VINL Input Voltage High, VINH Input Current, IINH, IINL V+ = 3.3V, VIN = 0V or V+ (Note 8) NOTES: 4. VIN = input voltage to perform proper function. 5. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. 6. Parts are 100% tested at +25°C. Limits across the full temperature range are guaranteed by design and correlation. 7. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range. 8. Guaranteed but not tested. 9. RON matching between channels is calculated by subtracting the channel with the highest max Ron value from the channel with lowest max Ron value. Electrical Specifications - 1.8V Supply PARAMETER Test Conditions: V+ = +1.65V to +2V, GND = 0V, VINH = 1.0V, VINL = 0.4V (Note 4, 6), Unless Otherwise Specified TEST CONDITIONS TEMP (°C) (NOTE 5) MIN Full 0 - V+ V 25 - 0.4 0.6 Ω TYP (NOTE 5) MAX UNITS ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG ON Resistance, RON V+ = 1.8V, ICOM = 100mA, VNO or VNC = 0V to V+, See Figure 5, Note 8 Full - - 0.6 Ω NO or NC OFF Leakage Current, INO(OFF) or INC(OFF) V+ = 2.0V, VCOM = 0.3V, 1.8V, VNO or VNC = 1.8V, 0.3V 25 -2 - 2 nA Full -40 - 40 nA COM ON Leakage Current, ICOM(ON) V+ = 2.0V, VCOM = 0.3V, 1.8V, or VNO or VNC = 0.3V, 1.8V 25 -3 - 3 nA Full -60 - 60 nA V+ = 1.65V, VNO or VNC = 1.0V, RL =50Ω, CL = 35pF, See Figure 1, Note 8 25 - 22 28 ns Full - - 33 ns V+ = 1.65V, VNO or VNC = 1.0V, RL =50Ω, CL = 35pF, See Figure 1, Note 8 25 - 9 15 ns Full - - 20 ns DYNAMIC CHARACTERISTICS Turn-ON Time, tON Turn-OFF Time, tOFF Break-Before-Make Time Delay, tD V+ = 2.0V, VNO or VNC = 1.0V, RL =50Ω, CL = 35pF, See Figure 3, Note 8 Full 2 9 - ns Charge Injection, Q CL = 1.0nF, VG = 0V, RG = 0Ω, See Figure 2 25 - 49 - pC OFF Isolation RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1VRMS, See Figure 4 25 - 68 - dB Crosstalk (Channel-to-Channel) RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1VRMS, See Figure 6 25 - -95 - dB NO or NC OFF Capacitance, COFF f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7 25 - 115 - pF COM ON Capacitance, CCOM(ON) 25 - 224 - pF f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7 DIGITAL INPUT CHARACTERISTICS Input Voltage Low, VINL Full - - 0.4 V Input Voltage High, VINH Full 1.0 - - V Full -0.5 - 0.5 µA Input Current, IINH, IINL V+ = 2.0V, VIN = 0V or V+ (Note 8) 4 FN6090.2 July 28, 2006 ISL43L410 Test Circuits and Waveforms V+ LOGIC INPUT V+ tr < 5ns tf < 5ns 50% C 0V tOFF SWITCH INPUT SWITCH INPUT VNO VOUT COM ADD 90% SWITCH OUTPUT VOUT NO or NC 90% 0V LOGIC INPUT GND INH CL 35pF RL 50Ω tON Logic input waveform is inverted for switches that have the opposite logic sense. Repeat test for all switches. CL includes fixture and stray capacitance. RL V OUT = V (NO or NC) -----------------------------R L + R ( ON ) FIGURE 1A. MEASUREMENT POINTS FIGURE 1B. TEST CIRCUIT FIGURE 1. SWITCHING TIMES V+ RG SWITCH OUTPUT VOUT C VOUT COM NO or NC ∆VOUT VG INH GND ADD CL V+ ON ON LOGIC INPUT LOGIC INPUT OFF 0V Q = ∆VOUT x CL Repeat test for all switches. FIGURE 2A. MEASUREMENT POINTS FIGURE 2B. TEST CIRCUIT FIGURE 2. CHARGE INJECTION V+ VNX V+ NO 0V RL 50Ω ADD LOGIC INPUT VOUT COM NC LOGIC INPUT SWITCH OUTPUT VOUT C GND CL 35pF INH 90% 0V tD Repeat test for all switches. CL includes fixture and stray capacitance. FIGURE 3A. MEASUREMENT POINTS FIGURE 3B. TEST CIRCUIT FIGURE 3. BREAK-BEFORE-MAKE TIME 5 FN6090.2 July 28, 2006 ISL43L410 Test Circuits and Waveforms (Continued) V+ C V+ C SIGNAL GENERATOR RON = V1/100mA NO or NC NO or NC ADD VNX 0V or V+ 100mA 0V or V+ ADD V1 COM ANALYZER GND INH COM RL GND Signal direction through switch is reversed, worst case values are recorded. Repeat test for all switches. INH Repeat test for all switches. FIGURE 4. OFF ISOLATION TEST CIRCUIT FIGURE 5. RON TEST CIRCUIT V+ C V+ C SIGNAL GENERATOR NO or NC COM 50Ω NO or NC ADD ADD 0V or V+ 0V or V+ IMPEDANCE ANALYZER NC or NO COM ANALYZER GND INH COM N.C. GND INH RL Signal direction through switch is reversed, worst case values are recorded. Repeat test for all switches. FIGURE 6. CROSSTALK TEST CIRCUIT Repeat test for all switches. FIGURE 7. CAPACITANCE TEST CIRCUIT Detailed Description Supply Sequencing And Overvoltage Protection The ISL43L410 is a bidirectional, double pole/double throw (DPDT) analog switch that offers precise switching capability from a single 1.65V to 3.6V supply with low on-resistance (0.25Ω) and high speed operation (tON = 12ns, tOFF = 5ns). The device is especially well suited for portable battery powered equipment due to its low operating supply voltage (1.65V), low power consumption (2.7µW max), low leakage currents (60nA max), and the tiny DFN and MSOP packages. The ultra low on-resistance and Ron flatness provide very low insertion loss and distortion to applications that require signal reproduction. With any CMOS device, proper power supply sequencing is required to protect the device from excessive input currents which might permanently damage the IC. All I/O pins contain ESD protection diodes from the pin to V+ and to GND (see Figure 8). To prevent forward biasing these diodes, V+ must be applied before any input signals, and the input signal voltages must remain between V+ and GND. If these conditions cannot be guaranteed, then one of the following two protection methods should be employed. 6 Logic inputs can easily be protected by adding a 1kΩ resistor in series with the input (see Figure 8). The resistor limits the input current below the threshold that produces FN6090.2 July 28, 2006 ISL43L410 permanent damage, and the sub-microamp input current produces an insignificant voltage drop during normal operation. This method is not acceptable for the signal path inputs. Adding a series resistor to the switch input defeats the purpose of using a low RON switch, so two small signal diodes can be added in series with the supply pins to provide overvoltage protection for all pins (see Figure 8). These additional diodes limit the analog signal from 1V below V+ to 1V above GND. The low leakage current performance is unaffected by this approach, but the switch signal range is reduced and the resistance may increase, especially at low supply voltages. OPTIONAL PROTECTION DIODE V+ OPTIONAL PROTECTION RESISTOR INX VNO or NC VCOM GND OPTIONAL PROTECTION DIODE FIGURE 8. OVERVOLTAGE PROTECTION Logic-Level Thresholds This switch family is 1.8V CMOS compatible (0.5V and 1.4V) over a supply range of 2.0V to 3.6V (See Figure 15). At 3.6V the VIH level is about 1.27V. This is still below the 1.8V CMOS guaranteed high output minimum level of 1.4V, but noise margin is reduced. The digital input stages draw supply current whenever the digital input voltage is not at one of the supply rails. Driving the digital input signals from GND to V+ with a fast transition time minimizes power dissipation. High-Frequency Performance In 50Ω systems, the signal response is reasonably flat even past 30MHz with a -3dB bandwidth of 120MHz (See Figure 16). The frequency response is very consistent over a wide V+ range, and for varying analog signal levels. An OFF switch acts like a capacitor and passes higher frequencies with less attenuation, resulting in signal feedthrough from a switch’s input to its output. Off Isolation is the resistance to this feedthrough, while Crosstalk indicates the amount of feedthrough from one switch to another. Figure 17 details the high Off Isolation and Crosstalk rejection provided by this part. At 100kHz, Off Isolation is about 68dB in 50Ω systems, decreasing approximately 20dB per decade as frequency increases. Higher load impedances decrease Off Isolation and Crosstalk rejection due to the voltage divider action of the switch OFF impedance and the load impedance. Leakage Considerations Power-Supply Considerations The ISL43L410 construction is typical of most single supply CMOS analog switches, in that they have two supply pins: V+ and GND. V+ and GND drive the internal CMOS switches and set their analog voltage limits. Unlike switches with a 4V maximum supply voltage, the ISL43L410 4.7V maximum supply voltage provides plenty of room for the 10% tolerance of 3.6V supplies, as well as room for overshoot and noise spikes. The minimum recommended supply voltage is 1.65V but the part will operate with a supply below 1.5V. It is important to note that the input signal range, switching times, and onresistance degrade at lower supply voltages. Refer to the electrical specification tables and Typical Performance curves for details. V+ and GND also power the internal logic and level shifters. The level shifters convert the input logic levels to switched V+ and GND signals to drive the analog switch gate terminals. Reverse ESD protection diodes are internally connected between each analog-signal pin and both V+ and GND. One of these diodes conducts if any analog signal exceeds V+ or GND. Virtually all the analog leakage current comes from the ESD diodes to V+ or GND. Although the ESD diodes on a given signal pin are identical and therefore fairly well balanced, they are reverse biased differently. Each is biased by either V+ or GND and the analog signal. This means their leakages will vary as the signal varies. The difference in the two diode leakages to the V+ and GND pins constitutes the analogsignal-path leakage current. All analog leakage current flows between each pin and one of the supply terminals, not to the other switch terminal. This is why both sides of a given switch can show leakage currents of the same or opposite polarity. There is no connection between the analog signal paths and V+ or GND. This family of switches cannot be operated with bipolar supplies, because the input switching point becomes negative in this configuration. 7 FN6090.2 July 28, 2006 ISL43L410 Typical Performance Curves TA = 25°C, Unless Otherwise Specified 0.32 0.7 V+ = 2.7V ICOM = 100mA ICOM = 100mA V+ = 1.5V 0.3 0.6 85°C 0.28 RON (Ω) RON (Ω) 0.5 0.4 V+ = 1.8V 0.3 V+ = 3.6V V+ = 2.7V 0.26 25°C 0.24 0.22 -40°C 0.2 0.2 V+ = 3V 0.18 0.1 0 1 2 3 0 4 0.5 1 1.5 2 2.5 3 VCOM (V) VCOM (V) FIGURE 10. ON RESISTANCE vs SWITCH VOLTAGE FIGURE 9. ON RESISTANCE vs SUPPLY VOLTAGE vs SWITCH VOLTAGE 0.5 100 V+ = 1.8V ICOM = 100mA 0.45 75 85°C V+ = 3V 50 0.35 Q (pC) RON (Ω) 0.4 25 V+ = 1.8V 0.3 0 25°C -40°C 0.25 -25 0.2 0 0.5 1 1.5 -50 2 0 0.5 1 VCOM (V) 1.5 2 2.5 3 VCOM (V) FIGURE 11. ON RESISTANCE vs SWITCH VOLTAGE FIGURE 12. CHARGE INJECTION vs SWITCH VOLTAGE 60 14 13 12 50 10 40 tOFF (ns) tON (ns) 11 30 9 85°C 8 -40°C 7 85°C 25°C 6 20 25°C 5 -40°C 4 10 1 1.5 2 2.5 3 V+ (V) 3.5 4 FIGURE 13. TURN - ON TIME vs SUPPLY VOLTAGE 8 4.5 3 1 1.5 2 2.5 3 3.5 4 4.5 V+ (V) FIGURE 14. TURN - OFF TIME vs SUPPLY VOLTAGE FN6090.2 July 28, 2006 ISL43L410 Typical Performance Curves TA = 25°C, Unless Otherwise Specified (Continued) 1.4 1.3 VINH AND VINL (V) 1.2 1.1 VINH 1 0.9 V+ = 3V 0 GAIN -20 0 PHASE 20 0.8 40 VINL 0.7 60 0.6 80 0.5 0.4 RL = 50Ω VIN = 0.2VP-P to 2VP-P 0.3 1 1.5 2 2.5 3 3.5 4 4.5 1 10 100 FREQUENCY (MHz) V+ (V) FIGURE 15. DIGITAL SWITCHING POINT vs SUPPLY VOLTAGE -10 100 600 FIGURE 16. FREQUENCY RESPONSE 10 V+ = 3V -20 20 Die Characteristics -30 30 SUBSTRATE POTENTIAL (POWERED UP): -40 40 -50 50 -60 60 ISOLATION -70 70 -80 80 GND OFF ISOLATION (dB) CROSSTALK (dB) PHASE (DEGREES) NORMALIZED GAIN (dB) 1.5 TRANSISTOR COUNT: 114 PROCESS: Submicron CMOS CROSSTALK -90 90 -100 100 -110 1k 10k 100k 1M 10M 110 100M 500M FREQUENCY (Hz) FIGURE 17. CROSSTALK AND OFF ISOLATION 9 FN6090.2 July 28, 2006 ISL43L410 Thin Dual Flat No-Lead Plastic Package (TDFN) L10.3x3A 2X 0.10 C A A 10 LEAD THIN DUAL FLAT NO-LEAD PLASTIC PACKAGE D MILLIMETERS 2X 0.10 C B SYMBOL MIN NOMINAL MAX NOTES A 0.70 0.75 0.80 - A1 - - 0.05 - E A3 6 INDEX AREA TOP VIEW B // A C SEATING PLANE 0.08 C b 0.20 0.25 0.30 5, 8 D 2.95 3.0 3.05 - D2 2.25 2.30 2.35 7, 8 E 2.95 3.0 3.05 - E2 1.45 1.50 1.55 7, 8 e 0.50 BSC - k 0.25 - - - L 0.25 0.30 0.35 8 A3 SIDE VIEW D2 (DATUM B) 0.10 C 0.20 REF 7 8 N 10 2 Nd 5 3 Rev. 3 3/06 D2/2 NOTES: 6 INDEX AREA 1 2 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. 2. N is the number of terminals. NX k 3. Nd refers to the number of terminals on D. (DATUM A) 4. All dimensions are in millimeters. Angles are in degrees. E2 E2/2 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. NX L N N-1 NX b 8 e (Nd-1)Xe REF. BOTTOM VIEW 5 7. Dimensions D2 and E2 are for the exposed pads which provide improved electrical and thermal performance. 0.10 M C A B 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. 9. Compliant to JEDEC MO-229-WEED-3 except for D2 dimensions. CL NX (b) (A1) L1 5 9 L e SECTION "C-C" C C TERMINAL TIP FOR ODD TERMINAL/SIDE 10 FN6090.2 July 28, 2006 ISL43L410 Mini Small Outline Plastic Packages (MSOP) N M10.118 (JEDEC MO-187BA) 10 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE E1 E INCHES SYMBOL -B- INDEX AREA 0.20 (0.008) 1 2 A B C TOP VIEW 4X θ 0.25 (0.010) R1 R GAUGE PLANE SEATING PLANE -CA 4X θ A2 A1 b -H- 0.10 (0.004) L SEATING PLANE C -Ae D 0.20 (0.008) C C a SIDE VIEW CL E1 0.20 (0.008) C D -B- MILLIMETERS MAX MIN MAX NOTES A 0.037 0.043 0.94 1.10 - A1 0.002 0.006 0.05 0.15 - A2 0.030 0.037 0.75 0.95 - b 0.007 0.011 0.18 0.27 9 c 0.004 0.008 0.09 0.20 - D 0.116 0.120 2.95 3.05 3 E1 0.116 0.120 2.95 3.05 4 e L1 MIN 0.020 BSC 0.50 BSC - E 0.187 0.199 4.75 5.05 - L 0.016 0.028 0.40 0.70 6 L1 0.037 REF 0.95 REF - N 10 10 7 R 0.003 - 0.07 - - R1 0.003 - 0.07 - - θ 5o 15o 5o 15o - α 0o 6o 0o 6o - END VIEW Rev. 0 12/02 NOTES: 1. These package dimensions are within allowable dimensions of JEDEC MO-187BA. 2. Dimensioning and tolerancing per ANSI Y14.5M-1994. 3. Dimension “D” does not include mold flash, protrusions or gate burrs and are measured at Datum Plane. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E1” does not include interlead flash or protrusions and are measured at Datum Plane. - H - Interlead flash and protrusions shall not exceed 0.15mm (0.006 inch) per side. 5. Formed leads shall be planar with respect to one another within 0.10mm (.004) at seating Plane. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. Dimension “b” does not include dambar protrusion. Allowable dambar protrusion shall be 0.08mm (0.003 inch) total in excess of “b” dimension at maximum material condition. Minimum space between protrusion and adjacent lead is 0.07mm (0.0027 inch). 10. Datums -A -H- . and - B - to be determined at Datum plane 11. Controlling dimension: MILLIMETER. Converted inch dimensions are for reference only All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 11 FN6090.2 July 28, 2006