Centaur Series T H R E E S T E P B AT T E R Y C H A R G E R FEATURES • • • • • • • 240W - 1440W 12V and 24V Battery Systems Three Step Charger Temperature Compensation Three Separate Outputs Charge 3 battery banks Corrosion Resistant SPECIFICATIONS INPUT PROTECTION Input Frequency 90 - 265Vac 90 - 400Vdc 45 - 65Hz Power Factor 1.0 Input Voltage Absorption Charge Voltages Float Charge Voltages Three Outputs Yes. Short Circuit Protection Yes. Over Temperature Protection Yes. STANDARDS OUTPUT Battery Charging Ignition Protected Optimum absorption charge and float voltages for Flooded Lead-acid, Gel-Cell or AGM batteries. Selectable by dip switch 14.3Vdc and 28.5Vdc See selection table 13.5Vdc and 27.0Vdc See selection table 3 isolated outputs that each can supply up to the fully rated current. Combined total rated current cannot be exceeded. Keeping within the total power rating of the battery charger. Safety EN60335-1, EN60335-2-29, UL1236. Emission Immunity EN55014, EN61000-3-2 Automotive Directive EN55012-2, EN61000-3-3 C-tick AS/NZS CISPR11: Group 1, Class A. ENVIRONMENTAL Operating Temperature -20°C to +60°C. Derating Full load up to 40C ambient, Output will reduce to approximately 80% of nominal at 50C and 60% of nominal at 60C Cooling Temperature and current controlled fan. 95% max (non condensing). Total Output Ammeter Yes. Humidity MECHANICAL Charge Characteristic Charges at the absorption rate, until the output has reduced to 70% of rated current. At which time a 4hour timer begins, then the charger switches to float rate Temperature Sensor Internal, -2mV/°C per cell. Battery Monitor The BMV-700 battery monitor features an advanced control and measuring system for battery voltage and charge/discharge current. The battery monitor displays battery voltage, current, consumed AH or time to go. Battery Alarm An excessively high or low battery voltage is indicated by an audible and visual alarm AC Connection Screw-clamp 4mm² (AWG 6) Battery Connection M6 or M8 studs See selection table Protection Category IP21. Material & Colour Aluminium epoxy powder coated cases (blue RAL 5012), Stainless steel fixings Size & Weight 12/20-12/30: 355 x 215 x 110mm, 3.8Kg 12/40-12/60, 24/30: 426 x 239 x 135mm, 5Kg 12/80-12/100, 24/40-24/60: 505 x 255 x 130m, 12Kg 12/200, 24/80-24/100: 505 x 255 x 230mm, 16Kg APPLICATION Doc. No. Centaur Rev.A 19-10-15 Centaur Series T H R E E S T E P B AT T E R Y C H A R G E R SELECTION TABLE Centaur 12/20 ABSORPTION CHARGE VOLTAGE 14.3V FLOAT CHARGE VOLTAGE 13.5V 20A BATTERY CONNECTION M6 studs RECOMMENDED BATTERY SIZE 80-200Ah Centaur 12/30 14.3V 13.5V 30A M6 studs 120-300Ah Centaur 12/40 14.3V Centaur 12/50 14.3V 163.5V 40A M8 studs 160-400Ah 13.5V 50A M8 studs 200-500Ah Centaur 12/60 14.3V 13.5V 60A M8 studs 240-600Ah Centaur 12/80 14.3V 13.5V 80A M8 studs 320-800Ah Centaur 12/100 14.3V 13.5V 100A M8 studs 400-1000Ah Centaur 24/16 28.5V 27V 16A M6 studs 45-150Ah Centaur 24/30 28.5V 27V 30A M8 studs 120-300Ah Centaur 24/40 28.5V 27V 40A M8 studs 160-400Ah Centaur 24/60 28.5V 27V 60A M8 studs 240-600Ah MODEL NUMBER OUTPUT CURRENT TECHNICAL ILLUSTRATIONS Doc. No. Centaur Rev.A 19-10-15 Powering Progress – www.powerbox.com.au