pdf

Description
Purpose and application
The TOUCH DIM RMC radio remote control enables the
wireless control of two TOUCH DIM RC radio receivers, each
with two channels. Up to four connected luminaire groups, each
with up to 15 electronic control gears featuring the TOUCH DIM®
function, can be independently operated.
TOUCH DIM RMC
Function
The TOUCH DIM RMC radio remote control sends radio signals
to the radio receiver, which converts these and transmits them
to the connected electronic control gears.
The radio remote control does not require batteries and is absolutely maintenance-free. The necessary transmission energy is
generated by an integrated inductive energy converter when the
pushbutton is pressed.
Design
A
C
B
D
The radio remote control is made up of the following components:
• Button 1: pushbutton for luminaire group (A) connected to
Ch 1 of the first radio receiver
• Button 2: pushbutton for luminaire group (B) connected to
Ch 2 of the first radio receiver
• Button 3: pushbutton for luminaire group (C) connected to
Ch 1 of the second radio receiver
• Button 4: pushbutton for luminaire group (D) connected to
Ch 2 of the second radio receiver
Radio remote control
Operating instructions
Operation
Functionality
The radio remote control can be used to operate two TOUCH
DIM RC radio receivers (E).
Ch 1
The radio control system of each radio receiver consists of two
channels (Ch 1 und Ch 2). The luminaire groups connected to
outputs „Ch 1“ and „Ch 2“ of the radio receivers can be independently operated with the radio remote control:
Ch 1
TOUCH DIM RC
First radio receiver:
TOUCH DIM RC
• Luminaire group on channel 1: button 1
Ch 2
• Luminaire group on channel 2: button 2
Ch 2
Second radio receiver:
• Luminaire group on channel 1: button 3
• Luminaire group on channel 2: button 4
Basically, the transmitters can be used to operate all TOUCH
DIM/TOUCH DIM sensor functions of OSRAM electronic control
gear.
The radio remote controls must be trained in the radio receiver.
Note:
To train the radio remote controls, see the separate instructions
of the TOUCH DIM RC radio receiver.
The radio transmission range between the radio remote control
and radio receiver is influenced by the following factors:
• Construction materials
• Type and number of obstacles between the transmitter and
receiver
2x
< 30 s
1
2
• Sources of interference and signal reflections
3
Switching on and off the luminaires
Via short press.
• Button 1: luminaire group on channel 1 of the first radio
receiver
A
2x
1
2 s
< 30
1
2
3
max
• Button 2: luminaire group on channel 2 of the first radio
receiver
3
• Button 3: luminaire group on channel 1 of the second radio
receiver
...
B
• Button 4: luminaire group on channel 2 of the second radio
receiver
Changing the brightness
A
> 30 s
1
2
1
3
2
max
Via long press.
3
B
...
• Button 1: luminaire group on channel 1 of the first radio
receiver
• Button 2: luminaire group on channel 2 of the first radio
receiver
• Button 3: luminaire group on channel 1 of the second radio
receiver
1
> 30 s
2
3
• Button 4: luminaire group on channel 2 of the second radio
receiver
Each repeated long key button press causes a toggle between
increased brightness and decreased brightness.
Page 1 of 2
Operation (cont.)
Troubleshooting
If you cannot remedy the fault, please contact the Customer
Service department of the luminaire manufacturer.
Luminaire does not function
No mains voltage present.
à Use a voltage tester to test if mains voltage is present.
Illuminants are faulty.
à Replace illuminant.
Luminaire was switched off via the wall-mounted or hand-held
transmitter.
à Switch on luminaire.
Luminaire does not react as expected to the press of a
button.
Hand-held transmitter has not been trained.
à Train the hand-held transmitter.
Radio receiver is too far away from the hand-held transmitter.
à Reduce the distance between the hand-held transmitter and
the radio receiver.
Button on the hand-held transmitter was pressed too long or
too short.
à See „Changing the brightness manually“.
Appendix
Technical data
Transmission
power
10 mW
Operating
temperature
-20 °C ... +50 °C
Frequency
band
868.3 MHz
Switching
cycles
> 50,000
Functional
range
In the open air: Approx. 300 m
Halls: Approx 100 m
Passageways and corridors: Approx. 50 m
Rooms with wooden or plasterboard walls:
Approx. 30 m (max. 7 walls)
Rooms with brick or autoclaved aerated
concrete walls:
Approx. 20 m (max. 3 walls)
Rooms with reinforced concrete walls:
Approx. 10 m (max. 1 wall)
Protection
type
IP 20
Weight
Approx. 46 g
Dimensions
(L x W x H)
82 x 49 x 20 mm
20 mm
82 mm
Dimensioned drawing
49 mm
IV 2009
Touch-DIM-RMC_ba0904en_we1.01.indd
OSRAM GmbH
Kunden Service Center
Customer-Service-Center (CSC)
Steinerne Furt 62
86167 Augsburg
Germany
Tel : +49 (0) 1803 677 - 200
(kostenpflichtig / charges apply)
Fax.: +49 (0) 1803 677 - 202
www.osram.com
www.osram.de
40083211830336
4008321183033
Conformity with the relevant EU directives is
confirmed by the CE symbol.
Page 2 of 2