DC-AC INVERTER UNIT PS-DA0416-01(S) (18 W DUAL OR QUAD OUTPUTS) (PRELIMINARY INFORMATION) DESCRIPTION : This low profile DC/AC inverter is developed for dual and quad lamps. Optimized for NEC Display: NL10276BC30-18 APPLICABLE LCD: 15inches quad lamps Lamp Voltage 620 Vrms Lamp Current 4 x 6,0 mArms Lamp Start Up Voltage 1.800 Vrms (Vin : 12 Vdc) FEATURES : Remote ON/OFF for 2 pairs independent or 4 CCFL Open lamp detection Wide dimming range Wide operating temperature RoHS compliant (S) TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity DIMENSIONS : -10°C ~ +70°C -20°C ~ +85°C 95 %RH max L x B x H 200 x 44 x 14 mm Unit : mm Weight :60 (g) typ. Note: Please use plastic screw in case of a non-insulating mounting base! Components No. 1 2 3 Part Description PCB Connector CN1 + CN6 Connector CN2 ~ CN5 Qty. 1 2 4 Input side CN1: Pin No. Symbols Ratings Vin 10.8 ~ 13.2 Vdc CN 1-1 Vin 10.8 ~ 13.2 Vdc CN 1-2 GND CN 1-3 GND CN 1-4 Vrm t 0 ~ 0.5 = OFF / 3.3 ~ Vin = ON CN 1-5 N.C. CN 1-6 Vbr 0 ~ 5.0 Vdc CN 1-7 Material UL94V-0 (FR-4 or CEM-3) S7B-PH-K-S SM02(8.0)B-BHS-1-TB Note t=1.6m m JST or equal JST or equal Input side CN6: Pin No. Symbols Ratings Vin 10.8 ~ 13.2 Vdc CN 1-1 Vin 10.8 ~ 13.2 Vdc CN 1-2 GND CN 1-3 GND CN 1-4 Vrm t 0 ~ 0.5 = OFF / 3.3 ~ Vin = ON CN 1-5 N.C. CN 1-6 Vbr 0 ~ 5.0 Vdc CN 1-7 Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (1) Version 2.0.1, 16th May 2014 DC-AC INVERTER UNIT PS-DA0416-01(S) (18 W DUAL OR QUAD OUTPUTS) (PRELIMINARY INFORMATION) Output side CN2 ~ CN5 Pin No. Symbols Ratings Vhigh 620Vrm s (6.0 m Arm s ) CN 2-1 N.C. CN2-2 Vlow (GND) CN 2-3 ELECTRICAL CHARACTERISTICS : Conditions Parameters Symbols Output Current Output Current Input Current Frequency Open Circuit Voltage Iout Iout Iin F Vopen Note 1 : Vin (V) Vbr (V) 12±1.2 12±0.6 12±1.2 12±1.2 11.4 0.0 5.0 0.0 0.0 0.0 Specification Tu (°C) -10 -10 -10 -10 -10 ~ +70 ~ +70 ~ +70 ~ +70 ~ +70 Min. Typ. Max. 5.5 50 1.550 6.0 15 1.67 55 1.800 6.5 2.17 60 - Unit Note m Arm s % Adc kHz Vrm s Dut y 100% Dut y Please keep a minimum of 2mm clearance in all directions between inverter high voltage areas and any conductors as marked on mechanical drawing. Please provide Vcc before applying any control signals into inverter. Revere the sequence during power off which is control signal off first then Vcc. Note 2: TEST CIRCUIT : F A Vin 10.8 ~ 13.2 V 1000:1 PROBE F Vopen Iin CN1-1 CN1-2 V V ~ CL1 CN2-1 SW3 CN1-3 CN1-4 T1 Vrmt 0 / 3.3 Vdc CN2-2 N.C. RL1 A ~ a V b SW1 CN1-6 CN1-7 Vbr 0 ~ 5.0 Vdc CN4-1 CN6-3 CN6-4 SW4 b SW2 Non Op erat ion SW 2 Operat io of unit a Operat io n b Non Op erat ion CN6-5 CN4-3 A ~ Iout 1 A ~ Iout 1 A ~ Iout 1 SW6 SW7 CN4-2 N.C. CN5-1 N.C. b RL1 RL1 a V Operat io n SW5 CN3-2 N.C. CN6-1 CN6-2 V Vrmt 0 / 3.3 Vdc CN3-1 CN3-3 Iin A Vin 10.8 ~ 13.2 V Operat io of unit a CN1-5 CN2-3 N.C. Iout 1 SW 1 SW8 SW9 CN6-6 CN6-7 CN5-2 N.C. Vbr 0 ~ 5.0 Vdc CN5-3 RL1 SW10 Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (2) Version 2.0.1, 16th May 2014