Freescale Semiconductor Technical Data Document Number: MC34712 Rev. 8.0, 5/2015 3.0 A 1.0 MHz Fully Integrated DDR Switch-Mode Power Supply 34712 The SMARTMOS 34712 is a highly integrated, space efficient, low cost, single synchronous buck switching regulator with integrated N-channel power MOSFETs. It is a high performance point-of-load (PoL) power supply with the ability to track an external reference voltage. Its high efficient 3.0 A sink and source capability combined with its voltage tracking/sequencing ability and tight output regulation, makes it ideal to provide the termination voltage (VTT) for modern data buses such as Double-Data-Rate (DDR) memory buses, including but not limited to DDR, DDR2, DDR3, and DDR4 memories. It also provides a buffered output reference voltage (VREF) to the memory chipset The 34712 offers the designer the flexibility of many control, supervisory, and protection functions to allow for easy implementation of complex designs. It is housed in a Pb-free, thermally enhanced, and space efficient 24 pin exposed pad QFN. Features SWITCH-MODE POWER SUPPLY • 50 m integrated N-channel power MOSFETs • Input voltage operating range from 3.0 V to 6.0 V • 1% Accurate output voltage, ranging from 0.6 V to 1.35 V • 1% Accurate buffered reference output voltage • Programmable switching frequency range from 200 kHz to 1.0 MHz with a default of 1.0 MHz • Overcurrent limit and short-circuit protection • Thermal shutdown • Output overvoltage and undervoltage detection • Active low power-good output signal • Active low standby and shutdown inputs VIN (3.0 TO 6.0 V) EP SUFFIX 98ARL10577D 24-PIN QFN 34712 PVIN VDDQ BOOT VREFIN VTT SW VIN VOUT VDDI FREQ GND SD TERMINATING RESISTORS VDDQ INV DDR MEMORY CHIPSET COMP VREFOUT PGND MCU STBY VREF VIN DDR MEMORY CONTROLLER PG Figure 1. 34712 Simplified Application Diagram © Freescale Semiconductor, Inc., 2007-2015. All rights reserved. MEMORY BUS VDDQ 1 Orderable Parts Table 1. Orderable Part Variations Part Number MC34712EP (1) Temperature (TA) Package -40 °C to 85 °C 24 QFN Notes 1. To order parts in Tape & Reel, add the R2 suffix to the part number. 34712 2 Analog Integrated Circuit Device Data Freescale Semiconductor 2 Internal Block Diagram STBY Thermal Monitoring PG Internal Voltage Regulator System Reset M1 System Control Ilimit Current Monitoring Isense FREQ SD M2 VDDI Discharge VIN BOOT VBOOT PVIN Oscillator Prog. Frequency VIN Buck Control Logic M3 FSW Gate Driver SW Isense PGND M4 VDDI Bandgap Regulator VBG Ramp Generator COMP PWM Comparator + – VDDI COMP Error Amplifier VREFIN + – RREF1 INV – + RREF2 Buffer M5 Discharge M6 VOUT Discharge GND VREFOUT Figure 2. 34712 Simplified Internal Block Diagram 34712 Analog Integrated Circuit Device Data Freescale Semiconductor 3 BOOT PVIN PVIN Pinout Diagram VIN 3.1 VIN Pin Connections VDDI 3 24 23 22 21 20 19 GND 1 18 PVIN FREQ 2 17 SW NC 3 16 SW 15 SW Transparent Top View PG 4 STBY 5 14 PGND SD 6 13 7 8 9 10 11 12 VREFIN VREFOUT COMP INV VOUT PGND PIN 25 PGND Figure 3. 34712 Pin Connections 3.2 Pin Definitions A functional description of each pin can be found in the Functional Pin Description section beginning on page 12. Table 2. 34712 Pin Definitions Pin Number Pin Name Pin Function Formal Name Signal Ground Definition 1 GND Ground 2 FREQ Passive Analog signal ground of IC 3 NC None No Connect No internal connections to this pin 4 PG Output Power Good Active-low (open drain) power-good status reporting pin 5 STBY Input Standby 6 SD Input Shutdown 7 VREFIN Input Voltage Tracking Reference Input 8 VREFOUT Output Reference Voltage Output 9 COMP Passive Compensation Buck converter external compensation network pin 10 INV Input Error Amplifier Inverting Input Buck converter error amplifier inverting input pin 11 VOUT Output Output Voltage Discharge FET Discharge FET drain connection (connect to buck converter output capacitors) 12,13,14 PGND Ground Power Ground Ground return for buck converter and discharge FET Frequency Adjustment Buck converter switching frequency adjustment pin Standby mode input control pin Shutdown mode input control pin Voltage tracking reference voltage input Buffered output equal to 1/2 of voltage-tracking reference 34712 4 Analog Integrated Circuit Device Data Freescale Semiconductor Table 2. 34712 Pin Definitions (continued) Pin Number Pin Name Pin Function Formal Name 15,16,17 SW Output Switching Node 18,19,20 PVIN Supply Power-circuit Supply Input 21 BOOT Passive Bootstrap 22,23 VIN Supply Logic-circuit Supply Input 24 VDDI Passive Internal Voltage Regulator 25 GND Ground Thermal Pad Definition Buck converter power switching node Buck converter main supply voltage input Bootstrap switching node (connect to bootstrap capacitor) Logic circuits supply voltage input Internal VDD regulator (connect filter capacitor to this pin) Thermal pad for heat transfer. Connect the thermal pad to the analog ground and the ground plane for heat sinking. 34712 Analog Integrated Circuit Device Data Freescale Semiconductor 5 4 Electrical Characteristics 4.1 Maximum Ratings Table 3. Maximum Ratings All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or permanent damage to the device. Symbol Ratings Value Unit Notes Input Supply Voltage (VIN) Pin -0.3 to 7.0 V PVIN High-side MOSFET Drain Voltage (PVIN) Pin -0.3 to 7.0 V VSW Switching Node (SW) Pin -0.3 to 7.0 V BOOT Pin (Referenced to SW Pin) -0.3 to 7.0 V - PG, VOUT, SD, and STBY Pins -0.3 to 7.0 V - VDDI, FREQ, INV, COMP, VREFIN, and VREFOUT Pins -0.3 to 3.0 V ±3.0 A (2) V (3) -40 to 85 °C (4) -65 to +150 °C ELECTRICAL RATINGS VIN VBOOT - VSW IOUT VESD1 VESD2 VESD3 Continuous Output Current ESD Voltage • Human Body Model • Machine Model (MM) • Device Charge Model (CDM) ±2000 ±200 ±750 THERMAL RATINGS TA Operating Ambient Temperature TSTG Storage Temperature TPPRT Peak Package Reflow Temperature During Reflow Note 6 °C TJ(MAX) Maximum Junction Temperature +150 °C PD Power Dissipation (TA = 85 °C) 2.9 W (5),(6) (7) Notes 2. Continuous output current capability so long as TJ is TJ(MAX). 3. ESD testing is performed in accordance with the Human Body Model (HBM) (CZAP = 100 pF, RZAP = 1500 ), the Machine Model (MM) (CZAP = 200 pF, RZAP = 0 ), and the Charge Device Model (CDM), Robotic (CZAP = 4.0 pF). 4. 5. The limiting factor is junction temperature, taking into account power dissipation, thermal resistance, and heatsinking. Pin soldering temperature limit is for 10 seconds maximum duration. Not designed for immersion soldering. Exceeding these limits may cause malfunction or permanent damage to the device. Freescale’s Package Reflow capability meets Pb-free requirements for JEDEC standard J-STD-020C. For Peak Package Reflow Temperature and Moisture Sensitivity Levels (MSL), Go to www.freescale.com, search by part number [e.g. remove prefixes/suffixes and enter the core ID to view all orderable parts. (i.e. MC33xxxD enter 33xxx), and review parametrics. Maximum power dissipation at indicated ambient temperature. 6. 7. 34712 6 Analog Integrated Circuit Device Data Freescale Semiconductor Table 3. Maximum Ratings (continued) All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or permanent damage to the device. Symbol Ratings Value Unit Notes THERMAL RESISTANCE (8) RJA Thermal Resistance, Junction to Ambient, Single-layer Board (1s) 139 °C/W (9) RJMA Thermal Resistance, Junction to Ambient, Four-layer Board (2s2p) 43 °C/W (10) Thermal Resistance, Junction to Board 22 °C/W (11) RJB Notes 8. 9. 10. 11. The PVIN, SW, and GND pins comprise the main heat conduction paths. Per SEMI G38-87 and JEDEC JESD51-2 with the single-layer board (JESD51-3) horizontal. Per JEDEC JESD51-6 with the board (JESD51-7) horizontal. There are no thermal vias connecting the package to the two planes in the board. Thermal resistance between the device and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on the top surface of the board near the package. 34712 Analog Integrated Circuit Device Data Freescale Semiconductor 7 4.2 Static Electrical Characteristics Table 4. Static Electrical Characteristics Characteristics noted under conditions 3.0 V VIN 6.0 V, - 40 C TA 85 C, GND = 0 V, unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 °C under nominal conditions, unless otherwise noted. Symbol Characteristic Min Typ Max Unit 3.0 - 6.0 V Notes IC INPUT SUPPLY VOLTAGE (VIN) VIN Input Supply Voltage Operating Range IIN Input DC Supply Current • Normal Mode: SD = 1 & STBY = 1, Unloaded Outputs - - 25 mA (12) Input DC Supply Current • Standby Mode, SD = 1 & STBY = 0 - - 15 mA (12) Input DC Supply Current • Shutdown Mode, SD = 0 & STBY = X - - 100 µA (12) 2.35 2.5 2.65 V IINQ IINOFF INTERNAL SUPPLY VOLTAGE OUTPUT (VDDI) VDDI Internal Supply Voltage Range BUCK CONVERTER (PVIN, SW, GND, BOOT, INV, COMP) PVIN High-side MOSFET Drain Voltage Range 2.5 - 6.0 V VOUT Output Voltage Adjustment Range 0.6 - 1.35 V (13), (17) Output Voltage Accuracy -1.0 - 1.0 % (13), (14), (15) REGLN Line Regulation • Normal Operation, VIN = 3.0 to 6.0 V, IOUT = ±3.0 A -1.0 - 1.0 % (13) REGLD Load Regulation • Normal Operation, IOUT = -3.0 to 3.0 A -1.0 - 1.0 % (13) VREF Error Amplifier Common Mode Voltage Range 0.0 - 1.35 V (13), (16) VUVR Output Undervoltage Threshold -8.0 - -1.5 % VOVR Output Overvoltage Threshold 1.5 - 8.0 % IOUT Continuous Output Current -3.0 - 3.0 A ILIM Overcurrent Limit, Sinking and Sourcing - 4.0 - A Short-circuit Current Limit • (Sourcing and Sinking) - 6.5 - A - ISHORT RDS(on)HS High-side N-CH Power MOSFET (M3) RDS(ON) • IOUT = 1.0 A, VBOOT - VSW = 3.3 V 10 - 50 m (13) RDS(on)LS Low-side N-CH Power MOSFET (M4) RDS(ON) • IOUT = 1.0 A, VIN = 3.3 V 10 - 50 m (13) Notes 12. 13. 14. 15. 16. 17. See section Modes of Operation, page 16 has a detailed description of the different operating modes of the 34712 Design information only, this parameter is not production tested. ±1% is assured at room temperature. Overall output accuracy is directly affected by the accuracy of the external feedback network, 1% feedback resistors are recommended. The 1% output voltage regulation is only guaranteed for a common mode voltage range greater than or equal to 0.6 V at room temperature. If a VOUT =0.6 V is desired, make sure PVIN is kept below 3.6 V and the Switching Frequency FSW is lower than 500 kHz to allow enough room for output regulation 34712 8 Analog Integrated Circuit Device Data Freescale Semiconductor Table 4. Static Electrical Characteristics Characteristics noted under conditions 3.0 V VIN 6.0 V, - 40 C TA 85 C, GND = 0 V, unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 °C under nominal conditions, unless otherwise noted. Symbol Min Typ Max Unit M2 RDS(on) • (VIN = 3.3 V, M2 is on) 1.5 - 4.0 ISW SW Leakage Current (Standby and Shutdown modes) -10 - 10 µA IPVIN PVIN Pin Leakage Current • (Standby and Shutdown Modes) -10 - 10 µA IINV INV Pin Leakage Current -1.0 - 1.0 µA AEA Error Amplifier DC Gain - 150 - dB (18) Error Amplifier Unit Gain Bandwidth - 3.0 - MHz (18) Error Amplifier Slew Rate - 7.0 - V/µs (18) -3.0 0.0 3.0 mV (18) RDS(on)M2 UGBWEA SREA OFFSETEA Characteristic Error Amplifier Input Offset Notes TSDFET Thermal Shutdown Threshold - 170 - °C (18) TSDHYFET Thermal Shutdown Hysteresis - 25 - °C (18) 0.0 - VDDI V VREFIN External Reference Voltage Range 0.0 - 2.7 V VREFOUT Buffered Reference Voltage Range 0.0 - 1.35 V VREFOUT Buffered Reference Voltage Accuracy -1.0 - 1.0 % IREFOUT VREFOUT Buffered Reference Voltage Current Capability 0.0 - 8.0 mA IREFOUTLIM VREFOUT Buffered Reference Voltage Overcurrent Limit - 11 - mA RTDR(M6) VREFOUT Total Discharge Resistance - 50 - (18) RTDR(M5) VOUT Total Discharge Resistance - 50 - (18) IVOUTLKG VOUT Pin Leakage Current • (Standby Mode, VOUT = 3.6 V) -1.0 - 1.0 µA OSCILLATOR (FREQ) VFREQ Oscillator Frequency Adjusting Reference Voltage Range TRACKING (VREFIN, VREFOUT, VOUT) VREFIN VREFOUT - (18) (19) CONTROL AND SUPERVISORY (STBY, SD, PG) VSTBYHI STBY High Level Input Voltage 2.0 - - V VSTBYLO STBY Low Level Input Voltage - - 0.4 V RSTBYUP STBY Pin Internal Pull-up Resistor 1.0 - 2.0 M VSDHI SD High Level Input Voltage 2.0 - - V VSDLO SD Low Level Input Voltage - - 0.4 V RSDUP SD Pin Internal Pull-up Resistor 1.0 - 2.0 M VPGLO PG Low Level Output Voltage • (IPG = 3.0 mA) - - 0.4 V IPGLKG PG Pin Leakage Current • (M1 is off, Pulled up to VIN) -1.0 - 1.0 µA Notes 18. Design information only, this parameter is not production tested. 19. The 1 % accuracy is only guaranteed for VREFOUT greater than or equal to 0.6 V at room temperature. 34712 Analog Integrated Circuit Device Data Freescale Semiconductor 9 4.3 Dynamic Electrical Characteristics Table 5. Dynamic Electrical Characteristics Characteristics noted under conditions 3.0 V VIN 6.0 V, - 40 C TA 85 C, GND = 0 V, unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 °C under nominal conditions, unless otherwise noted. Symbol Characteristic Min Typ Max Unit Notes BUCK CONVERTER (PVIN, SW, GND, BOOT) tRISE Switching Node (SW) Rise Time • (PVIN = 3.3 V, IOUT = ±3.0 A) - 14 - ns (21) tFALL Switching Node (SW) Fall Time • (PVIN = 3.3 V, IOUT = ±3.0 A) - 20 - ns (21) tOFFMIN Minimum OFF Time - 150 - ns tONMIN Minimum ON Time - 180 - ns tSS Soft Start Duration • (Normal Mode) 1.3 - 2.6 ms tLIM Overcurrent Limit Timer - 10 - ms Overcurrent Limit Retry Timeout Period 80 - 120 ms Output Undervoltage/Overvoltage Filter Delay Timer 5.0 - 25 µs tTIMEOUT tFILTER OSCILLATOR (FREQ) FSW Oscillator Default Switching Frequency • (FREQ = GND) - 1.0 - MHz FSW Oscillator Switching Frequency Range 200 - 1000 kHz (20) CONTROL AND SUPERVISORY (STBY, SD, PG) tPGRESET PG Reset Delay 8.0 - 12 ms tTIMEOUT Thermal Shutdown Retry Timeout Period 80 - 120 ms (21) Notes 20. Oscillator Frequency tolerance is ±10%. 21. Design information only, this parameter is not production tested. 34712 10 Analog Integrated Circuit Device Data Freescale Semiconductor 5 Functional Description 5.1 Introduction In modern microprocessor/memory applications, address commands and control lines require system level termination to a voltage (VTT) equal to 1/2 the memory supply voltage (VDDQ). Having the termination voltage at midpoint, the power supply insures symmetry for switching times. Also, a reference voltage (VREF) that is free of any noise or voltage variations is needed for the DDR SDRAM input receiver, VREF is also equal to 1/2 VDDQ. Varying the VREF voltage effects the setup and hold time of the memory. To comply with DDR requirements and to obtain best performance, VTT and VREF need to be tightly regulated to track 1/2 VDDQ across voltage, temperature, and noise margins. VTT should track any variations in the DC VREF value (VTT = VREF +/- 40mV), (See Figure 4) for a DDR system level diagram. The 34712 supplies the VTT and a buffered VREF output. To ensure compliance with DDR specifications, the VDDQ line is applied to the VREFIN pin and divided by 2 internally through a precision resistor divider. This internal voltage is then used as the reference voltage for the VTT output. The same internal voltage is also buffered to give the VREF voltage at the VREFOUT pin for the application to use without the need for an external resistor divider. The 34712 provides the tight voltage regulation and power sequencing/tracking required along with handling the DDR peak transient current requirements. Buffering the VREF output helps its immunity against noise and load changes. The 34712 utilizes a voltage mode synchronous buck switching converter topology with integrated low RDS(ON) (50 m) N-channel power MOSFETs to provide a VTT voltage with an accuracy of less than ±2.0%. It has a programmable switching frequency that allows for flexibility and optimization over the operating conditions and can operate at up to 1.0 MHz to significantly reduce the external components size and cost. The 34712 can sink and source up to 3.0 A of continuous current. It provides protection against output overcurrent, overvoltage, undervoltage, and overtemperature conditions. It also protects the system from short -circuit events. It incorporates a powergood output signal to alert the host when a fault occurs. For boards that support the Suspend-To-RAM (S3) and the Suspend-To-Disk (S5) states, the 34712 offers the STBY and the SD pins respectively. Pulling any of these pins low, puts the IC in the corresponding state. By integrating the control/supervisory circuitry along with the Power MOSFET switches for the buck converter into a space-efficient package, the 34712 offers a complete, small-size, cost-effective, and simple solution to satisfy the needs of DDR memory applications. Besides DDR memory termination, the 34712 can be used to supply termination for other active buses and graphics card memory. It can be used in Netcom/Telecom applications like servers. It can also be used in desktop motherboards, game consoles, set top boxes, and high end high definition TVs. VDDQ VTT VDDQ RT RS VREF BUS DDR Memory Controller DDR Memory Input Receiver Figure 4. DDR System Level Diagram 34712 Analog Integrated Circuit Device Data Freescale Semiconductor 11 5.2 Functional Pin Description 5.2.1 Reference Voltage Input (VREFIN) The 34712 tracks 1/2 the voltage applied at this pin. 5.2.2 Reference Voltage Output (VREFOUT) This is a buffered reference voltage output that is equal to 1/2 VREFIN. It has a 10 mA current drive capability. This output is used as the VREF voltage rail and should be filtered against any noise. Connect a 0.1 µF, 6.0 V low ESR ceramic filter capacitor between this pin and the GND pin and between this pin and VDDQ rail. VREFOUT is also used as the reference voltage for the buck converter error amplifier. 5.2.3 Frequency Adjustment Input (FREQ) The buck converter switching frequency can be adjusted by connecting this pin to an external resistor divider between VDDI and GND pins. The default switching frequency (FREQ pin connected to ground, GND) is set at 1.0 MHz. Select the switching frequency based on the PVIN to VTT ratio. Refer to the Switching Frequency Selection section. 5.2.4 Signal Ground (GND) Analog ground of the IC. Internal analog signals are referenced to this pin voltage. 5.2.5 Internal Supply Voltage Output (VDDI) This is the output of the internal bias voltage regulator. Connect a 1.0 µF, 6.0 V low ESR ceramic filter capacitor between this pin and the GND pin. Filtering any spikes on this output is essential to the internal circuitry stable operation. 5.2.6 Output Voltage Discharge Path (VOUT) Output voltage of the Buck Converter is connected to this pin. it only serves as the output discharge path once the SD signal is asserted. 5.2.7 Error Amplifier Inverting Input (inv) Buck converter error amplifier inverting input. Connect the VTT voltage directly to this pin. 5.2.8 Compensation Input (COMP) Buck converter external compensation network connects to this pin. Use a type III compensation network. 5.2.9 Input Supply Voltage (VIN) IC power supply input voltage. Input filtering is required for the device to operate properly. 5.2.10 Power Ground (PGND) Buck converter and discharge MOSFETs power ground. It is the source of the buck converter low-side power MOSFET. 5.2.11 Switching Node (SW) Buck converter switching node. This pin is connected to the output inductor. 34712 12 Analog Integrated Circuit Device Data Freescale Semiconductor 5.2.12 Power Input Voltage (PVIN) Buck converter power input voltage. This is the drain of the buck converter high-side power MOSFET. 5.2.13 Bootstrap Input (BOOT) Bootstrap capacitor input pin. Connect a capacitor (as discussed on page 24) between this pin and the SW pin to enhance the gate of the high-side Power MOSFET during switching. 5.2.14 Shutdown Input (SD) If this pin is tied to the GND pin, the device is in Shutdown mode. If left unconnected or tied to the VIN pin, the device is in Normal mode. The pin has an internal pull-up of 1.5 M. This input accepts the S5 (Suspend-To-Disk) control signal. 5.2.15 Standby Input (STBY) If this pin is tied to the GND pin, the device is in Standby mode. If left unconnected or tied to the VIN pin, the device is in Normal mode. The pin has an internal pull-up of 1.5 M. This input accepts the S3 (Suspend-To-RAM) control signal. 5.2.16 Power Good Output Signal (PG) This is an active low open drain output that is used to report the status of the device to a host. This output activates after a successful power up sequence and stays active as long as the device is in normal operation and is not experiencing any faults. This output activates after a 10 ms delay and must be pulled up by an external resistor to a supply voltage (e.g.,VIN.). 5.3 Functional Internal Block Description MC34712 - Functional Block Diagram Internal Bias Circuits System Control and Logic Oscillator Protection Functions Control and Supervisory Functions Tracking and Sequencing Buck Converter Figure 5. 34712 Internal Block Diagram 34712 Analog Integrated Circuit Device Data Freescale Semiconductor 13 5.3.1 Internal Bias Circuits This block contains all circuits that provide the necessary supply voltages and bias currents for the internal circuitry. It consists of: • Internal voltage supply regulator: This regulator supplies the VDDI voltage that is used to drive the digital/analog internal circuits. It is equipped with a Power-On-Reset (POR) circuit that watches for the right regulation levels. External filtering is needed on the VDDI pin. This block turns off during the shutdown mode. • Internal bandgap reference voltage: This supplies the reference voltage to some of the internal circuitry. • Bias circuit: This block generates the bias currents necessary to run all of the blocks in the IC. 5.3.2 System Control and logic This block is the brain of the IC where the device processes data and reacts to it. Based on the status of the STBY and SD pins, the system control reacts accordingly and orders the device into the right status. It also takes inputs from all of the monitoring/protection circuits and initiates power up or power down commands. It communicates with the buck converter to manage the switching operation and protects it against any faults. 5.3.3 Oscillator This block generates the clock cycles necessary to run the IC digital blocks. It also generates the buck converter switching frequency. The switching frequency has a default value of 1.0 MHz and can be programmed by connecting a resistor divider to the FREQ pin, between VDDI and GND pins (See Figure 1). 5.3.4 Protection Functions This block contains the following circuits: • Overcurrent limit and short-circuit detection: This block monitors the output of the buck converter for overcurrent conditions and shortcircuit events and alerts the system control for further command. • Thermal limit detection: This block monitors the temperature of the device for overheating events. If the temperature rises above the thermal shutdown threshold, this block alerts the system control for further commands. • Output overvoltage and undervoltage monitoring: This block monitors the buck converter output voltage to ensure it is within regulation boundaries. If not, this block alerts the system control for further commands. 5.3.5 Control and Supervisory Functions This block is used to interface with an outside host. It contains the following circuits: • Standby control input: An outside host can put the 34712 device into standby mode (S3 or Suspend-To-RAM mode) by sending a logic “0” to the STBY pin. • Shutdown control input: An outside host can put the 34712 device into shutdown mode (S5 or Suspend-To-Disk mode) by sending a logic “0” to the SD pin. • Power good output signal PG: The 34712 can communicate to an external host that a fault has occurred by releasing the drive on the PG pin high, allowing the signal/pin to be pulled high by the external pull-up resistor. 5.3.6 Tracking and Sequencing This block allows the output of the 34712 to track 1/2 the voltage applied at the VREFIN pin. This allows the VREF and VTT voltages to track 1/2 VDDQ and assures that none of them is higher than VDDQ at any point during normal operating conditions. For power down during a shutdown (S5) mode, the 34712 uses internal discharge MOSFETs (M5 and M6 on Figure 2) to discharge VTT and VREF respectively. These discharge MOSFETs are only active during shutdown mode. Using this block along with controlling the SD and STBY pins can offer the user power sequencing capabilities by controlling when to turn the 34712 outputs on or off. 34712 14 Analog Integrated Circuit Device Data Freescale Semiconductor 5.3.7 Buck Converter This block provides the main function of the 34712: DC to DC conversion from an un-regulated input voltage to a regulated output voltage used by the loads for reliable operation. The buck converter is a high-performance, fixed frequency (externally adjustable), synchronous buck PWM voltage-mode control. It drives integrated 50 mN-channel power MOSFETs saving board space and enhancing efficiency. The switching regulator output voltage is adjustable with an accuracy of less than ±2.0% to meet DDR requirements. Its output has the ability to track 1/2 the voltage applied at the VREFIN pin. The regulator's voltage control loop is compensated using a type III compensation network, with external components to allow for optimizing the loop compensation, for a wide range of operating conditions. A typical Bootstrap circuit with an internal PMOS switch is used to provide the voltage necessary to properly enhance the high-side MOSFET gate. The 34712 is designed to address DDR memory power supplies. The integrated converter has the ability to both sink and source up to 3.0 A of continuous current, making it suitable for bus termination power supplies. 34712 Analog Integrated Circuit Device Data Freescale Semiconductor 15 6 Functional Device Operation 6.1 Operational Modes SD = 1 & STBY=0 VIN < 3.0 V SD = 0 & STBY=x Shutdown VTT = Discharge VREF = Discharge PG = 1 Power Off VTT=OFF VREF=OFF PG = 1 Standby VTT = OFF VREF = ON PG = 1 3.0 V<=VIN<=6.0 V SD = 1 & STBY=1 SD = 1 & STBY=1 IOUT>=ISHORT VTT>VOV Overvoltage VTT=ON VREF=ON Normal VTT = ON VREF=ON VTT<VOV Short-circuit TIMEOUT Expired VTT=OFF VREF=OFF PG = 1 PG = 0 PG = 1 VTT>VUV TJ<=145 °C TIMEOUT Expired Undervoltage VTT<VUV VTT=ON VREF=ON Thermal Shutdown VTT=OFF VREF=OFF PG = 1 PG = 1 TIMEOUT Expired Over-current VTT=OFF VREF=ON PG = 1 IOUT1>=ILIM1 For>=10 ms TJ >= 170 °C Figure 6. Operation Modes Diagram 6.1.1 Modes of Operation The 34712 has three primary modes of operation: 6.1.1.1 Normal Mode In normal mode, all functions and outputs are fully operational. To be in this mode, the VIN needs to be within its operating range, both Shutdown and Standby inputs are high, and no faults are present. This mode consumes the most amount of power. 6.1.1.2 Standby Mode This mode is predominantly used in Desktop memory solutions where the DDR supply is desired to be ACPI compliant (Advanced Configuration and Power Interface). When this mode is activated by pulling the STBY pin low, VTT is put in High Z state, IOUT = 0 A, and VREF stays active. This is the S3 state Suspend-To-Ram or Self Refresh mode and it is the lowest DRAM power state. In this mode, the DRAM preserves the data. While in this mode, the 34712 consumes less power than in the normal mode, because the buck converter and most of the internal blocks are disabled. 34712 16 Analog Integrated Circuit Device Data Freescale Semiconductor 6.1.1.3 Shutdown Mode In this mode, activated by pulling the SD pin low, the chip is in a shutdown state and the outputs are all disabled and discharged. This is the S4/S5 power state or Suspend-To-Disk state, where the DRAM loses all of its data content (no power supplied to the DRAM). The reason to discharge the VTT and VREF lines is to ensure upon exiting, the Shutdown mode that VTT and VREF are lower than VDDQ, otherwise VTT can remain floating high, and be higher than VDDQ upon powering up. In this mode, the 34712 consumes the least amount of power since almost all of the internal blocks are disabled. 6.1.2 Start-up Sequence When power is first applied, the 34712 checks the status of the SD and STBY pins. If the device is in a shutdown mode, no block powers up and the output does not attempt to ramp. If the device is in a standby mode, only the VDDI internal supply voltage and the bias currents are established and no further activities occur. Once the SD and STBY pins are released to enable the device, the internal VDDI POR signal is also released. The rest of the internal blocks is enabled and the buck converter switching frequency value is determined by reading the FREQ pin. A soft start cycle is then initiated to ramp up the output of the buck converter (VTT). The buck converter error amplifier uses the voltage on the VREFOUT pin (VREF) as its reference voltage. VREF is equal to 1/2 VDDQ, where VDDQ is applied to the VREFIN pin. This way, the 34712 assures that VREF and VTT voltages track 1/2 VDDQ to meet DDR requirements. Soft start is used to prevent the output voltage from overshooting during startup. At initial startup, the output capacitor is at zero volts; VOUT = 0 V. Therefore, the voltage across the inductor is PVIN during the capacitor charge phase which creates a very sharp di/dt ramp. Allowing the inductor current to rise too high can result in a large difference between the charging current and the actual load current that can result in an undesired voltage spike once the capacitor is fully charged. The soft start is active each time the IC goes out of standby or shutdown mode, power is recycled, or after a fault retry. To fully take advantage of soft starting, it is recommended not to enable the 34712 output before introducing VDDQ on the VREFIN pin. If this happens after a soft start cycle expires and the VREFIN voltage has a high dv/dt, the output naturally tracks it immediately and ramp up with a fast dv/dt itself and this defeats the purpose of soft starting. For reliable operation, it is best to have the VDDQ voltage available before enabling the output of the 34712. After a successful start-up cycle where the device is enabled, no faults have occurred, and the output voltage has reached its regulation point, the 34712 pulls the power good output signal low after a 10 ms reset delay, to indicate to the host the device is in normal operation. 6.2 Protection and Diagnostic Features The 34712 monitors the application for several fault conditions to protect the load from overstress. The reaction of the IC to these faults ranges from turning off the outputs to just alerting the host that something is wrong. In the following paragraphs, each fault condition is explained: 6.2.1 Output Overvoltage An overvoltage condition occurs once the output voltage goes higher than the rising overvoltage threshold (VOVR). In this case, the power good output signal is pulled high, alerting the host that a fault is present, but the VTT and VREF outputs stays active. To avoid erroneous overvoltage conditions, a 20 µs filter is implemented. The buck converter uses its feedback loop to attempt to correct the fault. Once the output voltage falls below the falling overvoltage threshold (VOVF), the fault is cleared and the power good output signal is pulled low, the device is back in normal operation. 6.2.2 Output Undervoltage An undervoltage condition occurs once the output voltage falls below the falling undervoltage threshold (VUVF). In this case, the power good output signal is pulled high, alerting the host that a fault is present, but the VTT and VREF outputs stays active. To avoid erroneous undervoltage conditions, a 20 µs filter is implemented. The buck converter uses its feedback loop to attempt to correct the fault. Once the output voltage rises above the rising undervoltage threshold (VUVR), the fault is cleared and the power good output signal is pulled low, the device is back in normal operation. 34712 Analog Integrated Circuit Device Data Freescale Semiconductor 17 6.2.3 Output Overcurrent This block detects overcurrent in the Power MOSFETs of the buck converter. It is comprised of a sense MOSFET and a comparator. The sense MOSFET acts as a current detecting device by sampling a ratio of the load current. That sample is compared via the comparator with an internal reference to determine if the output is in over-current or not. If the peak current in the output inductor reaches the over current limit (ILIM), the converter starts a cycle-by-cycle operation to limit the current, and a 10 ms over-current limit timer (tLIM) starts. The converter stays in this mode of operation until one of the following occurs: • The current is reduced back to the normal level before tLIM expires, and in this case normal operation is regained. • tLIM expires without regaining normal operation, at which point the device turns off the output and the power good output signal is pulled high. At the end of a timeout period of 100 ms (tTIMEOUT), the device attempts another soft start cycle. • The device reaches the thermal shutdown limit (TSDFET) and turns off the output. The power good output signal is pulled high. 6.2.4 Short-circuit Current Limit This block uses the same current detection mechanism as the overcurrent limit detection block. If the load current reaches the ISHORT value, the device reacts by shutting down the output immediately. This is necessary to prevent damage in case of a permanent short circuit. Then, at the end of a timeout period of 100 ms (tTIMEOUT), the device attempts another soft start cycle. 6.2.5 Thermal Shutdown Thermal limit detection block monitors the temperature of the device and protects against excessive heating. If the temperature reaches the thermal shutdown threshold (TSDFET), the converter output switches off and the power good output signal indicates a fault by pulling high. The device stays in this state until the temperature has decreased by the hysteresis value and then after a timeout period (TTIMEOUT) of 100 ms, the device retries automatically and the output goes through a soft start cycle. If successful normal operation is regained, the power good output signal is asserted low. 34712 18 Analog Integrated Circuit Device Data Freescale Semiconductor Typical Applications BOOT VIN Compensation Network C15 0.1 F VDDI VOUT R2 12.7 k_nopop x 4 PG PGOOD LED VMASTER VMASTER R8 10 k_nopop 5 STBY VIN 6 SD R7 1k VREFIN VREFIN D1 LED R9 10 k_nopop 3 NC PVIN VIN GND GND VMASTER VOUT Optional nopop 3 2 1 3 2 1 PVIN PVIN SW PG STBY SD GND 7 8 9 C13 0.1 F 10 11 18 17 16 SW SW 15 14 GND 13 GND 12 INV C11 0.1 F COMP VOUT Jumpers 4.7_nopop R16 SW MC34712 I/O Signals C16 0.1 F PVIN SW VREFOUT C17 10 F 19 FREQ LED VIN BOOT VIN SGND C12 0.1 F VIN Capacitors 20 GND 2 VIN 1 R11 10 k 21 INV C19 1.9 nF R1 20 k 22 COMP R14 300 23 VREFOUT R15 15 k C20 1.0 nF 24 VDDI FREQ C18 0.02 pF PVIN C14 0.1 F VREFIN R12 10 k_nopop INV COMP PVIN SW VOUT 7 J2 J3 PVIN VMASTER STBY_nopop LED 1 2 1 2 1 3 5 7 9 J1 2 4 6 8 10 VREFIN PG STBY SD CON10A SD VDDI Buck Converter FREQ R6 POT_50 k_nopop SW PVIN Capacitors D3 PMEG2010EA _nopop L1 1.5 H VOUT2 VOUT1 VOUT R3 4.7_nopop C7 C6 C8 C9 100 F 100 F 100 F 1 nF_nopop PVIN C1 0.1 F C2 1 F C3 C4 C5 100 F 100 F 100 F 34712 Analog Integrated Circuit Device Data Freescale Semiconductor 19 7.1 Component Selection 7.1.1 Switching Frequency Selection The switching frequency defaults to a value of 1.0 MHz when the FREQ pin is grounded, and 200 kHz when the FREQ pin is connected to VDDI. Intermediate switching frequencies can be obtained by connecting an external resistor divider to the FREQ pin. Table 6 shows the resulting switching frequency versus FREQ pin voltage. To ensure the VTT (VOUT) regulation, frequency should be selected such that the buck regulator switch ON time is higher than 300 ns. For example, for a 3.3 VIN bus and 0.6 V VTT, choose fSW of 466 kHz. Table 6. Switching Frequency Adjustment FREQUENCY VOLTAGE APPLIED TO PIN FREQ 200 2.341 – 2.500 253 2.185 - 2.340 307 2.029 - 2.184 360 1.873 - 2.028 413 1.717 – 1.872 466 1.561 – 1.716 520 1.405 - 1.560 573 1.249 - 1.404 627 1.093 - 1.248 680 0.936 - 1.092 733 0.781 - 0.936 787 0.625 - 0.780 840 0.469 - 0.624 893 0.313 - 0.468 947 0.157 - 0.312 1000 0.000 - 0.156 RFQH RFQL VDDI FREQ GND Figure 7. Resistor Divider for Frequency Adjustment 34712 20 Analog Integrated Circuit Device Data Freescale Semiconductor 7.2 Selection of the Inductor Inductor calculation is straight forward, being where, Maximum OFF time percentage Switching period. Drain – to – source resistance of FET Winding resistance of Inductor Output current ripple. 7.3 Output Filter Capacitor For the output capacitor, the following considerations are more important than the actual capacitance value, the physical size, the ESR and the voltage rating: Transient Response percentage, TR_% (Use a recommended value of 2 to 4% to assure a good transient response.) Maximum Transient Voltage, TR_v_dip = Vo*TR_% Maximum current step, Inductor Current rise time, where, D_max = Maximum ON time percentage. IO = Rated output current. Vin_min = Minimum input voltage at PVIN 34712 Analog Integrated Circuit Device Data Freescale Semiconductor 21 As a result, it is possible to calculate In order to find the maximum allowed ESR, The effects of the ESR is often neglected by the designers and may present a hidden danger to the ultimate supply stability. Poor quality capacitors have widely disparate ESR value, which can make the closed loop response inconsistent. Io Io_step Current response dt_I_rise Worst case assumption Figure 8. Transient Parameters 7.3.1 Type III Compensation Network Power supplies are desired to offer accurate and tight regulation output voltages. To accomplish this requires a high DC gain, but with high gain comes the possibility of instability. The purpose of adding compensation to the internal error amplifier is to counteract some of the gains and phases contained in the control-to-output transfer function that could jeopardized the stability of the power supply. The Type III compensation network used for 34712 comprises two poles (one integrator and one high frequency pole to cancel the zero generated from the ESR of the output capacitor) and two zeros to cancel the two poles generated from the LC filter as shown in Figure 9. Gate Driver FSW SW PWM Comparitor + – Ramp Generator L VOUT RS Error Amplifier – + VREFOUT RO CO CS INV RF COMP CX CF 34712 Figure 9. Type III Compensation Network 34712 22 Analog Integrated Circuit Device Data Freescale Semiconductor Consider the crossover frequency, FCROSS, of the open loop gain at one-tenth of the switching frequency, FSW. Then, 10 F CROSS = ---------------------------2 R O C F 10 C F = --------------------------------------2 R O F CROSS where RO is a user selected resistor. Knowing the LC frequency, it can be obtained the values of RF and CS: This gives as a result, & Calculate Rs by placing the Pole 1 at the ESR zero frequency: Equating the Pole 2 to 5 times the Crossover Frequency to achieve a faster response and a proper phase margin, 34712 Analog Integrated Circuit Device Data Freescale Semiconductor 23 5 F CROSS = F 1 ---------------------------------------P2 = CF CX 2 R F --------------------CF + CX 7.3.2 Bootstrap Capacitor The bootstrap capacitor is needed to supply the gate voltage for the high-side MOSFET. This N-Channel MOSFET needs a voltage difference between its gate and source to be able to turn on. The high-side MOSFET source is the SW node, so it is not ground and it is floating and moving in voltage, so it cannot just apply a voltage directly to the gate of the high-side that is referenced to ground, a voltage referenced to the SW node is needed. That is why the bootstrap capacitor is needed for. This capacitor charges during the high-side off time, since the low-side is on during that time, so the SW node and the bottom of the bootstrap capacitor is connected to ground and the top of the capacitor is connected to a voltage source, so the capacitor charges up to that voltage source (say 5.0 V). Now when the lowside MOSFET switches off and the high-side MOSFET switches on, the SW nodes rises up to Vin, and the voltage on the boot pin is VCAP + VIN. So the gate of the high-side has VCAP across it and it is able to stay enhanced. A 0.1 F capacitor is a good value for this bootstrap element. 7.3.3 Layout Guidelines The layout of any switching regulator requires careful consideration. First, there are high di/dt signals present, and the traces carrying these signals need to be kept as short and as wide as possible to minimize the trace inductance, and therefore reduce the voltage spikes they can create. To do this, an understanding of the major current carrying loops is important. See Figure 10. These loops, and their associated components, should be placed in such a way as to minimize the loop size to prevent coupling to other parts of the circuit. Also, the current carrying power traces and their associated return traces should run adjacent to one another, to minimize the amount of noise coupling. If sensitive traces must cross the current carrying traces, they should be made perpendicular to one another to reduce field interaction. Second, small signal components which connect to sensitive nodes need consideration. The critical small signal components are the ones associated with the feedback circuit. The high impedance input of the error amp is especially sensitive to noise, and the feedback and compensation components should be placed as far from the switch node, and as close to the input of the error amplifier as possible. Other critical small signal components include the bypass capacitors for VIN, VREFIN, and VDDI. Locate the bypass capacitors as close to the pin as possible. The use of a multi-layer printed circuit board is recommended. Dedicate one layer, usually the layer under the top layer, as a ground plane. Make all critical component ground connections with vias to this layer. Make sure that the power ground, PGND, is connected directly to the ground plane and not routed through the thermal pad or analog ground. Dedicate another layer as a power plane and split this plane into local areas for common voltage nets. The IC input supply (VIN) should be connected with a dedicated trace to the input supply. This helps prevent noise from the Buck Regulator's power input (PVIN) from injecting switching noise into the IC’s analog circuitry. In order to effectively transfer heat from the top layer to the ground plane and other layers of the printed circuit board, thermal vias need to be used in the thermal pad design. It is recommended that 5 to 9 vias be spaced evenly and have a finished diameter of 0.3 mm. VIN1 VIN2PVIN and 3 Loop Curr ent HS ON HS Loop Curr ent HS ON Buck Converter SW3 SW2 and SW1 SD HS Loop Current SD ON LS Loop Current LS ON GND2 and 3 PGND Figure 10. Current Loops 34712 24 Analog Integrated Circuit Device Data Freescale Semiconductor 8 Packaging 8.1 Packaging Dimensions Package dimensions are provided in package drawings. To find the most current package outline drawing, go to www.freescale.com and perform a keyword search for the drawing’s document number. Package Suffix 24-Pin QFN EP Package Outline Drawing Number 98ARL10577D 34712 Analog Integrated Circuit Device Data Freescale Semiconductor 25 34712 26 Analog Integrated Circuit Device Data Freescale Semiconductor 34712 Analog Integrated Circuit Device Data Freescale Semiconductor 27 9 Revision History REVISION DATE DESCRIPTION OF CHANGES 1.0 2/2006 2.0 11/2006 3.0 2/2007 4.0 5/2007 • • • • • • • • • • • • • • • • • • • • • • • • • • • • 5.0 12/2008 • • • Pre-release version Implemented Revision History page Initial release Converted format from Market Assessment to Product Preview Major updates to the data, form, and style Replaced all electrolytic capacitors with ceramic ones in Figure 1 Deleted Deadtime in Dynamic Electrical Characteristics Moved Figures 8 ahead of Type III Compensation Network Changed Features from 2% to 1% Changed 34712 Simplified Application Diagram Removed Machine Model in Maximum Ratings Added minimum limits to Input DC Supply Current Normal mode, Input DC Supply Current Standby mode, and Input DC Supply Current Shutdown mode Added High-side MOSFET Drain Voltage Range Changed Output Voltage Accuracy Changed Short-circuit Current Limit Changed High-side N-CH Power MOSFET (M3) RDS(ON) and Low-side N-CH Power MOSFET (M4) RDS(ON) Changed M2 RDS(on) Changed PVIN Pin Leakage Current Changed VREFOUT Buffered Reference Voltage Accuracy, VREFOUT Buffered Reference Voltage Current Capability, and VREFOUT Buffered Reference Voltage Overcurrent Limit Changed STBY Pin Internal Pull-up Resistor and SD Pin Internal Pull-up Resistor Changed Soft Start Duration, Overcurrent Limit Retry Timeout Period, and Output Undervoltage/Overvoltage Filter Delay Timer Changed Oscillator Default Switching Frequency Changed PG Reset Delay and Thermal Shutdown Retry Timeout Period Changed drawings in Typical Applications Changed drawing in Type III Compensation Network Removed PC34712EP/R2 from the ordering information and added MC34712EP/R2 Changed the data sheet status to Advance Information Made changes to Switching Node (SW) Pin, BOOT Pin (Referenced to SW Pin), Output Undervoltage Threshold, Output Overvoltage Threshold, High-side N-CH Power MOSFET (M3) RDS(ON), Low-side N-CH Power MOSFET (M4) RDS(ON), Device Charge Model (CDM) Added Machine Model (MM), SW Leakage Current (Standby and Shutdown modes), Error Amplifier DC Gain, Error Amplifier Unit Gain Bandwidth, Error Amplifier Slew Rate, Error Amplifier Input Offset Added pin 25 to Figure 3 and the 34712 Pin Definitions Added the section Layout Guidelines 6.0 4/2012 • Changed typical for Minimum ON Time on page 10 7.0 3/2015 • Added note (17) to Static Electrical Characteristics 8.0 5/2015 • Minimum output voltage extended to 0.6 V 34712 28 Analog Integrated Circuit Device Data Freescale Semiconductor How to Reach Us: Information in this document is provided solely to enable system and software implementers to use Freescale products. Home Page: freescale.com There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits based Web Support: freescale.com/support Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no on the information in this document. warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale data sheets and/or specifications can and do vary in different applications, and actual performance may vary over time. All operating parameters, including “typicals,” must be validated for each customer application by customer’s technical experts. Freescale does not convey any license under its patent rights nor the rights of others. Freescale sells products pursuant to standard terms and conditions of sale, which can be found at the following address: freescale.com/SalesTermsandConditions. Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. SMARTMOS is a trademark of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © 2015 Freescale Semiconductor, Inc. Document Number: MC34712 Rev. 8.0 5/2015