SAW Bandpass Filter F2434 Features Narrow bandpass filter High attenuation Usable bandwidth 50kHz 50Ω single-ended operation Ceramic Surface Mounted Device (SMD) Package Package Dimensions 5.00 7.00± 0.15 3 4 10 1.00± 0.15 2.54 2434 0.60 5.00± 0.15 ITF 1 2 5 9 7 8 1.50± 0.1 6 Dimensions shown are nominal in millimeters Pin Configuration Body : Al2O3 Ceramic Lid : Kovar, Ni Plated Terminations : Au plating 0.3 ~ 1.0 um, Over a 1.27 ~ 8.89 um Ni Plating 9 Input 4 Output Others Ground Maximum Ratings Parameter Unit Minimum Typical Maximum Operating Temperature Range °C -25 25 60 Storage Temperature Range °C -30 - 70 Power Handling Capability dBm - - 10 Electrostatics Sensitive Device (ESD) I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F2434 Rev. Date 2012-06-18 Rev. NCNF01-AS01 1/7 SAW Bandpass Filter F2434 Specifications Fc = 243MHz Minimum Typical Maximum MHz - 243 - Insertion Loss (Fc +/- 25 kHz) dB - 3.7 6.0 Amplitude Ripple (Fc +/- 25 kHz) dB - 0.2 1.0 usec - 0.5 2.0 50 42 29 29 42 50 63 64 68 64 63 55 - - -0.032 - Center Frequency ( Fc ) Group Delay Variation (Fc +/- 25 kHz) Attenuation Fc -115 Fc -1 Fc -0.6 Fc +0.4 Fc +0.6 Fc +1 ~ ~ ~ ~ ~ ~ Fc -1 MHz Fc -0.6 MHz Fc -0.4 MHz Fc +0.6 MHz Fc +1 MHz Fc +115 MHz Temperature Coefficient of Frequency dB ppm/°C2 Notes : 1) All specifications are based on the matching schematic shown below, measured by Agilent Network analyzer and full 2 port calibration. 2) Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances 3) All attenuation measurements are measured relative to insertion loss I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F2434 Rev. Date 2012-06-18 Rev. NCNF01-AS01 2/7 SAW Bandpass Filter F2434 Matching Schematic ( Actual matching values may vary due to PCB layout and parasitics ) , L1 ,L2 = 120nH C1 ,C2 = 1.5pF Marking Configuration ITF1) 24342) 1) Manufacturer name 2) Part Number I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F2434 Rev. Date 2012-06-18 Rev. NCNF01-AS01 3/7 SAW Bandpass Filter F2434 Typical Performance ( at 25℃ ℃ ) I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F2434 Rev. Date 2012-06-18 Rev. NCNF01-AS01 4/7 SAW Bandpass Filter F2434 Typical Performance ( at 25℃ ℃ ) I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F2434 Rev. Date 2012-06-18 Rev. NCNF01-AS01 5/7 SAW Bandpass Filter F2434 Packing Specification 1. Reeling Quantity : 1000 pcs / reel 2. Taping Structure : The tape shall be wound around the reel in the direction shown below. TOP COVER TAPE REEL CARRIER TAPE Tape Specification 1. Leader part and vacant position specification Vacant 150mm min. Component contained Vacant 150mm min. Leader part 250mm min. END START Tape Running Direction 2. Tensile strength of carrier tape 4.4N/mm width Direction of pull Top cover tape 3. Top cover tape adhesion 0~ 15 degree 1) pull off angle : 0~15° 2) speed : 300mm/min 3) force : 20~70g I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Carrier tape Part No. F2434 Rev. Date 2012-06-18 Rev. NCNF01-AS01 6/7 SAW Bandpass Filter F2434 Carrier Tape Dimensions [unit : mm] A 5.50 ± 0.1 B 7.50 ± 0.1 C 9.25 ± 0.1 D 1.80 ± 0.1 E 16.00 ± 0.3 F 8.00 ± 0.1 Part Direction Tape Running Direction Reel Dimensions [unit : mm] G = 2G = 16.40 mm I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F2434 Rev. Date 2012-06-18 Rev. NCNF01-AS01 7/7