SAW Bandpass Filter F7512 Features RF bandpass filter High attenuation Matching 50Ω single-ended operation Ceramic Surface Mounted Device (SMD) Package ( 5.0 mm * 5.0 mm ) RoHS Compliant 5.00± 0.15 0.6± 0.15 2.08± 0.15 Package Dimension – SMD 5.0 × 5.0 1.2± 0.15 ITF 7512 7 1 6 2 5 3 1.27± 0.05 1.35± 0.15 5.00± 0.15 8 4 Pin Configuration Dimensions shown are nominal in millimeters 2 Input 6 Output Body : Al2O3 Ceramic 1, 3, 4, 5, 7, 8 Lid : Kovar, Ni Plated Terminations : Au plating 0.3 ~ 1.0 um, Over a 1.27 ~ 8.89 um Ni Plating Case ground Maximum Ratings Parameter Unit Minimum Typical Maximum Operating Temperature Range ℃ -30 25 70 Storage Temperature Range ℃ -40 25 85 Power Handling Capability dBm - - 10 Electrostatics Sensitive Device (ESD) I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F7512 Rev. Date 2011-07-27 Rev. NCMF01-AS01 1/7 SAW Bandpass Filter F7512 Specifications Fc = 757.5 MHz Terminating source impedance : 50Ω Terminating load impedance : 50Ω Minimum Typical Maximum Unit Center Frequency ( Fc ) - 757.5 - MHz Insertion Loss (757MHz ~ 758MHz) - 2.2 5.0 dB Amplitude ripple (757MHz ~ 758MHz) - 0.2 1.5 dB VSWR (757MHz ~ 758MHz) - 1.5 2.0 40 40 15 30 40 43.5 42 29 40 48 - Attenuation DC 707 MHz 764 MHz 787 MHz 798 MHz ~ 707 MHz ~ 730 MHz ~ 776 MHz ~ 788 MHz ~ 2000 MHz Input/Output Impedance dB 50 Ohms Notes : 1) All specifications are based on the matching schematic shown below, measured by Agilent Network analyzer and full 2 port calibration. 2) Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F7512 Rev. Date 2011-07-27 Rev. NCMF01-AS01 2/7 SAW Bandpass Filter F7512 Matching Schematic ( Actual matching values may vary due to PCB layout and parasitics ) Input 50Ω Output 50Ω Marking Configuration ITF 1) 7512 2) 1) Manufacturer name 2) Marking Number * Ink or Laser Marking available I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F7512 Rev. Date 2011-07-27 Rev. NCMF01-AS01 3/7 SAW Bandpass Filter F7512 Typical Performance ( at 25℃ ℃) I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F7512 Rev. Date 2011-07-27 Rev. NCMF01-AS01 4/7 SAW Bandpass Filter F7512 Input / Output VSWR Charts Input / Output Smith Charts I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F7512 Rev. Date 2011-07-27 Rev. NCMF01-AS01 5/7 SAW Bandpass Filter F7512 Packing Specification 1. Reeling Quantity : 1000 pcs / reel 2. Taping Structure : The tape shall be wound around the reel in the direction shown below. TOP COVER TAPE REEL CARRIER TAPE Tape Specification 1. Leader part and vacant position specification Vacant 150mm min. Component contained Vacant 150mm min. Leader part 250mm min. END START Tape Running Direction 2. Tensile strength of carrier tape 4.4N/mm width Direction of pull Top cover tape 3. Top cover tape adhesion 0~ 15 degree 1) pull off angle : 0~15° 2) speed : 300mm/min 3) force : 20~70g I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Carrier tape Part No. F7512 Rev. Date 2011-07-27 Rev. NCMF01-AS01 6/7 SAW Bandpass Filter F7512 Carrier Tape Dimensions [unit : mm] A 5.50 ± 0.1 B 5.50 ± 0.1 C 7.25 ± 0.1 D 1.95 ± 0.1 E 12.00 ± 0.1 F 8.00 ± 0.1 Part Direction Tape Running Direction Reel Dimensions [unit : mm] I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F7512 Rev. Date 2011-07-27 Rev. NCMF01-AS01 7/7