SAW Bandpass Filter F1G5A Features GPS Application High attenuation Usable bandwidth 2.4MHz No matching 50Ω single-ended operation Ceramic Surface Mounted Device (SMD) Package ( 3.0 mm * 3.0 mm ) RoHS Compliant Package Dimension – SMD 3.0 × 3.0 1 2 I 1G5A 3 6 6 1 5 5 2 4 4 3 Pin Configuration Dimensions shown are nominal in millimeters 2 Input Body : Al2O3 Ceramic Lid : Kovar, Ni Plated Terminations : Au plating 0.3 ~ 1.0 um, Over a 1.27 ~ 8.89 um Ni Plating 5 Output 1, 3, 4, 6 Case ground Maximum Ratings Parameter Unit Minimum Typical Maximum Operating Temperature Range ℃ -30 25 70 Storage Temperature Range ℃ -40 25 85 Power Handling Capability dBm 10 Electrostatics Sensitive Device (ESD) I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. NCMB02-F1G5A Rev. Date 2011-3-16 Rev. AS 01 1/7 SAW Bandpass Filter F1G5A Specifications Fc = 1575.42 MHz Terminating source impedance : 50Ω Terminating load impedance : 50Ω Minimum Typical Maximum Unit Center Frequency ( Fc ) - 1575.42 - MHz Insertion Loss (In Fc +/- 2.4 MHz) - 1.5 2.0 dB Amplitude Ripple (In Fc +/- 2.4 MHz) - 0.2 1.0 dBp-p VSWR (In Fc +/- 2.4 MHz) - 1.5 2.0 DC ~ 1400 MHz 37 42 - 1400 ~ 1490 MHz 40 45 - 1490 ~ 1520 MHz 33 40 - 1625 ~ 1635 MHz 30 49 - 1800 ~ 3000 MHz 33 38 - -30 25 70 ℃ - 10 - dBm Relative Attenuation Temperature Range (Operational) Input RF Power (In Fc +/- 2.4 MHz) Input/Output Impedance 50 dB Ohms Notes : 1) All specifications are based on the matching schematic shown below, measured by Agilent Network analyzer and full 2 port calibration. 2) Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. NCMB02-F1G5A Rev. Date 2011-3-16 Rev. AS 01 2/7 SAW Bandpass Filter F1G5A Matching Schematic ( Actual matching values may vary due to PCB layout and parasitics ) Input 50Ω Output 50Ω Marking Configuration 1) I2) 1G5A3) 1) Pad Number 1 Index 2) Manufacturer name 3) Marking Number * Ink or Laser Marking available I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. NCMB02-F1G5A Rev. Date 2011-3-16 Rev. AS 01 3/7 SAW Bandpass Filter F1G5A Typical Performance ( at 25℃ ℃) I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. NCMB02-F1G5A Rev. Date 2011-3-16 Rev. AS 01 4/7 SAW Bandpass Filter F1G5A Input / Output VSWR Charts Input / Output Smith Charts I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. NCMB02-F1G5A Rev. Date 2011-3-16 Rev. AS 01 5/7 SAW Bandpass Filter F1G5A Packing Specification 1. Reeling Quantity : 1000 pcs / reel 2. Taping Structure : The tape shall be wound around the reel in the direction shown below. TOP COVER TAPE REEL CARRIER TAPE Tape Specification 1. Leader part and vacant position specification Vacant 150mm min. Component contained Vacant 150mm min. Leader part 250mm min. END START Tape Running Direction 2. Tensile strength of carrier tape 4.4N/mm width Direction of pull Top cover tape 3. Top cover tape adhesion 0~15 degree 1) pull off angle : 0~15° 2) speed : 300mm/min 3) force : 20~70g I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Carrier tape Part No. NCMB02-F1G5A Rev. Date 2011-3-16 Rev. AS 01 6/7 SAW Bandpass Filter F1G5A Carrier Tape Dimensions [unit : mm] A 3.40 ± 0.1 B 3.40 ± 0.1 C 7.25 ± 0.1 D 1.70 ± 0.1 E 12.00 ± 0.1 F 8.00 ± 0.1 Part Direction Tape Running Direction Reel Dimensions [unit : mm] I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. NCMB02-F1G5A Rev. Date 2011-3-16 Rev. AS 01 7/7