SAW Bandpass Filter F1G5N Features RF bandpass filter No matching 50Ω single-ended operation Ceramic Surface Mounted Device Package ( 1.4 mm × 1.1 mm ) RoHS Compliant This part is compliant with AEC-Q200 Package Dimensions Pin Configuration Dimensions shown are nominal in millimeters 1 Input Body : Al2O3 Ceramic Lid : Kovar, Ni Plated Terminations : Au plating 0.3 ~ 1.0 um, Over a 1.27 ~ 8.89 um Ni Plating 4 Output 2, 3, 5 Ground Maximum Ratings Parameter Unit Minimum Typical Maximum Operating Temperature Range ℃ -40 25 105 Storage Temperature Range ℃ -40 - 105 Power Handling Capability dBm - - 10 I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F1G5N Rev. Date 2015-11-30 Rev. AS03 1/6 SAW Bandpass Filter F1G5N Specifications Fc = 1575.42 MHz Minimum Typical Maximum Unit Center Frequency ( Fc ) - 1575.42 - MHz Insertion Loss ( 1574.22 ~ 1576.62 MHz ) - 1.3 1.8 dB Amplitude Ripple ( 1574.22 ~ 1576.62 MHz ) - 0.1 0.5 dB p-p VSWR ( 1574.22 ~ 1576.62 MHz ) - 1.2 1.6 0.3 ~ 824 MHz 37 42 824 ~ 894 MHz 37 42 1710 ~ 1880 MHz 40 45 1920 ~ 2170 MHz 42 50 2170 ~ 3000 MHz 45 50 Attenuation Input/Output Impedance - dB - 50 Ohms Notes : 1) All specifications are based on the matching schematic shown below, measured by Agilent Network analyzer and full 2 port calibration. 2) Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F1G5N Rev. Date 2015-11-30 Rev. AS03 2/6 SAW Bandpass Filter F1G5N Matching Schematic ( Actual matching values may vary due to PCB layout and parasitics ) Input 50Ω Output 50Ω Marking Configuration 029 2) B 1) 1) Series Number 2) Date Code * Ink or Laser Marking available I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F1G5N Rev. Date 2015-11-30 Rev. AS03 3/6 SAW Bandpass Filter F1G5N Typical Performance ( at 25℃ ℃) I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F1G5N Rev. Date 2015-11-30 Rev. AS03 4/6 SAW Bandpass Filter F1G5N Input / Output VSWR Charts Input / Output Smith Charts I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F1G5N Rev. Date 2015-11-30 Rev. AS03 5/6 SAW Bandpass Filter F1G5N Packing Specification 1. Reeling Quantity : 3000 pcs / 13” reel ( or 1000 pcs / 7” reel ) 2. Taping Structure : The tape shall be wound around the reel in the direction shown below. TOP COVER TAPE REEL CARRIER TAPE Tape Specification 1. Leader part and vacant position specification Vacant 150mm min. Component contained Vacant 150mm min. Leader part 250mm min. END START Tape Running Direction 2. Tensile strength of carrier tape 4.4N/mm width Direction of pull Top cover tape 3. Top cover tape adhesion 0~15 degree 1) pull off angle : 0~15° 2) speed : 300mm/min 3) force : 20~70g I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Carrier tape Part No. F1G5N Rev. Date 2015-11-30 Rev. AS03 6/6