SAW Bandpass Filter F1G90 Features RF bandpass filter High attenuation No matching single-ended operation Ceramic Surface Mounted Device Package ( 3.0 mm × 3.0 mm ) RoHS Compliant Package Dimension 1 I 1G90 2 3 6 6 1 5 5 2 4 4 3 Pin Configurations Dimensions shown are nominal in millimeters Body : Al2O3 Ceramic Lid : Kovar, Ni Plated Terminations : Au plating 0.3 ~ 1.0 um, Over a 1.27 ~ 8.89 um Ni Plating 2 Input 5 Output 1, 3, 4, 6 Case ground Maximum Ratings Parameters Unit Minimum Typical Maximum Operating Temperature Range ℃ -20 25 70 Storage Temperature Range ℃ -40 - 85 Power Handling Capability dBm - - 10 Electrostatics Sensitive Device (ESD) 2010 I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F1G90 Rev. Date 2014-03-21 Rev. NCLH01-AS02 1/7 SAW Bandpass Filter F1G90 Specifications Fo = 1900.0 MHz Minimum Typical Maximum Unit Center Frequency ( Fc ) - 1900.0 - MHz Insertion Loss (In Fc ±20.0 MHz) - 2.7 3.5 dB Amplitude Ripple (In Fc ±20.0 MHz) - 0.8 1.5 dB VSWR (In Fc ±20.0 MHz) - 1.5 2.0 30 35 - 1000.0 MHz ~ 1700.0 MHz 30 35 - 1700.0 MHz ~ 1830.0 MHz 32 38 - 1970.0 MHz ~ 2400.0 MHz 38 45 - 2400.0 MHz ~ 3000.0 MHz 30 40 - Relative Attenuation 0.3 MHz ~ 1000.0 MHz Input/Output Impedance dB 50 Ohm Notes : 1) All specifications are based on the matching schematic shown below 2) All specifications are measured by Agilent Network analyzer and full 2 port calibration at room temperature 3) All attenuation measurements are measured relative to insertion loss 2010 I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F1G90 Rev. Date 2014-03-21 Rev. NCLH01-AS02 2/7 SAW Bandpass Filter F1G90 Matching Schematic ( Actual matching values may vary due to PCB layout and parasitics ) Input 50Ω Output 50Ω Marking Configuration 1) I2) 1G903) 1) Pad Number 1 Index 2) Manufacturer name 3) Marking Number * Ink or Laser Marking available 2010 I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F1G90 Rev. Date 2014-03-21 Rev. NCLH01-AS02 3/7 SAW Bandpass Filter F1G90 Typical Performance ( at +25℃ ℃) 2010 I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F1G90 Rev. Date 2014-03-21 Rev. NCLH01-AS02 4/7 SAW Bandpass Filter F1G90 2010 I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F1G90 Rev. Date 2014-03-21 Rev. NCLH01-AS02 5/7 SAW Bandpass Filter F1G90 Packing Specification 1. Reeling Quantity : 3000 pcs / 13” reel ( or 1000 pcs / 7” reel ) 2. Taping Structure : The tape shall be wound around the reel in the direction shown below. TOP COVER TAPE REEL CARRIER TAPE Tape Specification 1. Leader part and vacant position specification Vacant 150mm min. Component contained Vacant 150mm min. Leader part 250mm min. END START Tape Running Direction 2. Tensile strength of carrier tape 4.4N/mm width Direction of pull Top cover tape 3. Top cover tape adhesion 0~15 degree 1) pull off angle : 0~15° 2) speed : 300mm/min 3) force : 20~70g 2010 I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Carrier tape Part No. F1G90 Rev. Date 2014-03-21 Rev. NCLH01-AS02 6/7 SAW Bandpass Filter F1G90 Carrier Tape Dimensions [unit : mm] A 3.40 ± 0.1 B 3.40 ± 0.1 C 7.25 ± 0.1 D 1.70 ± 0.1 E 12.00 ± 0.1 F 8.00 ± 0.1 Part Direction Tape Running Direction Reel Dimensions [unit : mm] 2010 I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F1G90 Rev. Date 2014-03-21 Rev. NCLH01-AS02 7/7