SAW Bandpass Filter F2G3E Features Low-loss RF filter for digital radio No matching 50Ω single-ended operation Ceramic Surface Mounted Device (SMD) Package ( 3.0 mm * 3.0 mm ) RoHS Compliant This part is compliant with AEC-Q200 Package Dimension – SMD 3.0 × 3.0 1 2 I 2G3E 3 6 6 1 5 5 2 4 4 3 Pin Configuration Dimensions shown are nominal in millimeters 2 Body : Al2O3 Ceramic Lid : Kovar, Ni Plated Terminations : Au plating 0.3 ~ 1.0 um, Over a 1.27 ~ 8.89 um Ni Plating Input 5 Output 1, 3, 4, 6 Case ground Maximum Ratings Parameter Unit Minimum Typical Maximum Operating Temperature Range ℃ - 25 - Storage Temperature Range ℃ - 25 - Power Handling Capability dBm 10 Electrostatics Sensitive Device (ESD) I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F2G3E Rev. Date 2016-04-12 Rev. AS01 1/5 SAW Bandpass Filter F2G3E Preliminary Specifications Fc = 2332.5 MHz Minimum Typical Maximum Unit Center Frequency ( Fc ) - 2332.5 - MHz Insertion Loss ( 2320 ~ 2345 MHz ) - 0.65 0.95 dB Amplitude Ripple ( 2320 ~ 2345 MHz ) - 0.2 0.5 dB p-p VSWR ( 2320 ~ 2345 MHz ) - 1.4 1.8 824 ~ 894 MHz 15.0 22.0 - 1710 ~ 1755 MHz 16.0 18.5 1850 ~ 1990 MHz 16.0 18.5 - 2400 ~ 2415 MHz 15.0 35.0 - 2415 ~ 2600 MHz 15.0 20.0 - Attenuation Input/Output Impedance dB 50 Ohms Notes : 1) All specifications are based on the matching schematic shown below, measured by Agilent Network analyzer and full 2 port calibration. 2) Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances 3) All attenuation measurements are measured relative to insertion loss I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F2G3E Rev. Date 2016-04-12 Rev. AS01 2/5 SAW Bandpass Filter F2G3E Matching Schematic ( Actual matching values may vary due to PCB layout and parasitics ) Input 50Ω C1 C2 Output 50Ω C1, C2 = 3.3 pF Marking Configuration 1) I2) 2G3E3) 1) Pad Number 1 Index 2) Manufacturer name 3) Marking Number * Ink or Laser Marking available I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F2G3E Rev. Date 2016-04-12 Rev. AS01 3/5 SAW Bandpass Filter F2G3E Typical Performance ( at 25℃ ℃) I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F2G3E Rev. Date 2016-04-12 Rev. AS01 4/5 SAW Bandpass Filter F2G3E Input / Output VSWR Charts Input / Output Smith Charts I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F2G3E Rev. Date 2016-04-12 Rev. AS01 5/5 SAW Bandpass Filter F2G3E Packing Specifications 1. Reeling Quantity : 3000 pcs / 13” reel ( or 1000 pcs / 7” reel ) 2. Taping Structure : The tape shall be wound around the reel in the direction shown below. TOP COVER TAPE REEL CARRIER TAPE Tape Specification 1. Leader part and vacant position specification Vacant 150mm min. Component contained Vacant 150mm min. Leader part 250mm min. END START Tape Running Direction 2. Tensile strength of carrier tape 4.4N/mm width Direction of pull Top cover tape 3. Top cover tape adhesion 0~15 degree 1) pull off angle : 0~15° 2) speed : 300mm/min 3) force : 20~70g I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Carrier tape Part No. F2G3E Rev. Date 2016-04-12 Rev. AS01 6/5 SAW Bandpass Filter F2G3E Carrier Tape Dimensions [unit : mm] A 3.40 ± 0.1 B 3.40 ± 0.1 C 7.25 ± 0.1 D 1.70 ± 0.1 E 12.00 ± 0.1 F 8.00 ± 0.1 Part Direction Tape Running Direction Reel Dimensions [unit : mm] I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F2G3E Rev. Date 2016-04-12 Rev. AS01 7/5