l11767 kled1059e

Red LED
L11767
High output power red emitting diode
The L11767 is a high output red LED that delivers light output more than twice that of our previous products. Electric power
required to provide the same brightness as the previous products is reduced by as much as 70%. The L11767 also offers
high reliability since it is a 4-element (AlGaInP) LED.
Features
Applications
High radiant output power (more than twice compared to previous products)
13 mW (IF=20 mA typ.)
High reliability
Optical switches, etc.
Absolute maximum ratings (Ta=25 °C unless otherwise noted)
Parameter
Reverse voltage
Forward current
Derating rate of forward
current
Pulse forward current
Derating rate of pulse
forward current
Power dissipation
Operating temperature
Storage temperature
Soldering condition
Symbol
VR
IF
IFP
P
Topr
Tstg
-
Condition
Value
5
60
Unit
V
mA
Ta > 25 °C
0.8
mA/°C
Pulse width=10 μs
Duty ratio=1%
0.5
A
Ta > 25 °C
6.7
mA/°C
180
-30 to +85
-40 to +100
Less than 260 °C, within 5 seconds *2
mW
°C
°C
-
*1
*1: Guaranteed to resist temperature cycle test of up to 5 cycles
*2: At a position at least 1 mm away from the lead base
Note: Exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. Always be sure to use the
product within the absolute maximum ratings.
Electrical and optical characteristics (Ta=25 °C)
Parameter
Symbol
Condition
Peak emission wavelength
λp
IF=20 mA
Spectral half-width
Δλ
IF=20 mA
Forward voltage
VF
IF=20 mA
Reverse current
IR
VR=5 V
Radiant flux
φe
IF=20 mA
Cutoff frequency*3
fc
IF=20 mA ± 1 mAp-p
Min.
650
10
3
Typ.
660
18
2.1
13
6
Max.
670
30
2.5
20
-
Unit
nm
nm
V
μA
mW
MHz
*3: Frequency at which the light output drops by 3 dB relative to the output at 100 kHz
www.hamamatsu.com
1
Red LED
L11767
Emission spectrum
Radiant flux vs. forward current
(Typ. Ta=25 °C, IF=20 mA)
100
(Typ. Ta=25 °C, tw=100 μs, 0.1%)
1000
Radiant flux (mW)
Relative light output (%)
80
60
40
100
10
20
0
600
620
640
660
680
1
10
700
100
Wavelength (nm)
1000
Forward current (mA)
KLEDB0344EA
KLEDB0345EC
Forward current vs. forward voltage
Directivity
(Typ. Ta=25 °C, tw=100 μs, 0.1%)
1000
20°
10°
0°
10°
(Typ. Ta=25 °C)
20°
30°
30°
40°
40°
50°
Forward current (mA)
50°
60°
60°
100
70°
70°
80°
90°
100
10
80°
80
60
40
20
0
20
40
60
80
90°
100
Relative light output (%)
Excluding light reflected from base
1
1
2
3
4
5
6
Forward voltage (V)
KLEDB0346EB
KLEDB0348EA
2
Red LED
L11767
Light output vs. ambient temperature
Allowable forward current vs. ambient temperature
(Typ. IF=20 mA)
Relative allowable forward current (%)
3
Relative light output (dB)
2
1
0
-1
-2
-3
-4
-5
-40
-20
0
20
40
60
80
100
Ambient temperature (°C)
100
80
60
40
20
0
-40
-20
0
20
40
60
80
100
Ambient temperature (°C)
KLEDB0347EA
KLEDB0027EC
Allowable forward current vs. duty ratio
(Ta=25 °C)
1000
Pulse width=1 μs
Allowable forward current (mA)
Pulse width=10 μs
Pulse width=100 μs
100
10
0.01
0.1
1
10
100
Duty ratio (%)
KLEDB0349EB
3
Red LED
L11767
Dimensional outline (unit: mm)
1.12 ± 0.1
Clear epoxy resin ϕ4.2 ± 0.1
ϕ0.45
lead
13.5
2.3 ± 0.3
ϕ5.4 ± 0.1
ϕ2.54 ± 0.2
Common to case
KLEDA0009ED
Related information
www.hamamatsu.com/sp/ssd/doc_en.html
Precautions
∙ Disclaimer
∙ Metal, ceramic, plastic products
Information described in this material is current as of November, 2015.
Product specifications are subject to change without prior notice due to improvements or other reasons. This document has been carefully prepared and the
information contained is believed to be accurate. In rare cases, however, there may be inaccuracies such as text errors. Before using these products, always
contact us for the delivery specification sheet to check the latest specifications.
The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that
one year period. However, even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product use.
Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission.
www.hamamatsu.com
HAMAMATSU PHOTONICS K.K., Solid State Division
1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184
U.S.A.: Hamamatsu Corporation: 360 Foothill Road, Bridgewater, N.J. 08807, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218
Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 8152-375-0, Fax: (49) 8152-265-8
France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10
United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777
North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 35 16440 Kista, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01
Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moia, 1 int. 6, 20020 Arese (Milano), Italy, Telephone: (39) 02-93581733, Fax: (39) 02-93581741
China: Hamamatsu Photonics (China) Co., Ltd.: B1201, Jiaming Center, No.27 Dongsanhuan Beilu, Chaoyang District, Beijing 100020, China, Telephone: (86) 10-6586-6006, Fax: (86) 10-6586-2866
Cat. No. KLED1059E03 Nov. 2015 DN
4