Toggles Series FR02 Rockers General Specifications Pushbuttons Electrical Capacity (Resistive Load) Switching Rating: 100mA @ 5V DC 100mA @ 50V DC Programmable Illuminated PB Other Ratings Contact Resistance: 100 milliohms maximum for circuit; 30 milliohms maximum for contact point Insulation Resistance: 1,000 megohms minimum @ 250V DC Dielectric Strength: 250V AC minimum for 1 minute minimum Mechanical Life: 10,000 detent operations minimum Electrical Life: 10,000 detent operations minimum Notes: A detent operation is one actuator position operation or stepping. A cycle is one 360° rotation. 10,000 detent operations equal 625 cycles for hexadecimal devices or 1,000 cycles for decimal devices. Nominal Operating Torque: 0.008Nm for decimal devices; 0.01Nm for hexadecimal devices Contact Timing: Nonshorting Keylocks Rotaries Slides Tactiles Tilt Touch Indicators Nonswitching Rating: Materials & Finishes G Actuator: Housing & Base: Leaf Spring: Movable Contacts: Stationary Contacts: Terminals: Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: Screwdriver and Plastic Shaft - Glass fiber reinforced polyamide (UL94V-0) Glass fiber reinforced polyamide (UL94V-0) Stainless steel Copper alloy with gold plating Phosphor bronze with gold plating Phosphor bronze with gold plating –25°C through +85°C (–13°F through +185°F) 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 5 minutes; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Processing Soldering: Cleaning: Standards & Certifications Flammability Standards: Reflow Soldering Recommended. See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Note: During soldering process, set the switch to the following position: FR02FR10P, FR02FR16P, FR02KR10P, FR02KR16P: 0 position; FR02FC10P, FR02KC10P: 7 position; FR02FC16P, FR02KC16P: F position These devices are not process sealed. Hand clean locally using alcohol based solution. UL94V-0 rated actuator, housing, & base The FR02 Series rotaries have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current circuit. When used as intended, the results do not produce hazardous energy. Supplement Accessories 10mm Ultra-Thin SMT DIP Rotaries G12 www.nkk.com Toggles Series FR02 10mm Ultra-Thin SMT DIP Rotaries Rockers Distinctive Characteristics Pushbuttons Slim .150” (3.8mm) body has the lowest profile in the industry and allows close stacking of PC boards. Programmable Illuminated PB Highly visible legends and choice of screwdriver or shaft actuators with arrow position indication provide trouble-free code setting. Detent mechanism gives crisp, positive action for accurate switch setting. Gull-winged terminals ensure mechanical stability during soldering and simplify solder joint inspection. Cam activated movable contact and gold contacts assure contact reliability and continuity. G Actual Size Slides Tape-reel packaging meets EIA-481-2 Standard. Tilt Tactiles Coplanarity: all considered surfaces must lie between two parallel planes that are a maximum distance apart of .0059” (0.15mm). (Additional coplanarity details in Terms and Acronyms in the Supplement section.) TRUTH TABLES (CIRCUITS & POSITIONS) 10 Decimal 16 Hexadecimal 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 A B C D E F 1 Model Numbers: FR02FR, FR02KR 2 Indicators R Real Coded 4 8 Accessories Coded Model Numbers: FR02FC, FR02KC 1 2 4 8 Supplement C Complement Touch Actuator Position x = ON Terminal No. (Output) Rotaries Keylocks Use of heat resistant resin allows infrared convection reflow soldering. Terminal numbers are actually on the switch. www.nkk.com G13 Series FR02 Toggles 10mm Ultra-Thin SMT DIP Rotaries TYPICAL SWITCH ORDERING EXAMPLE Pushbuttons Rockers FR 02 F Mounting Programmable Illuminated PB 02 10 P Circuits SMT S Terminals R Real Coded (Orange Actuator) C Complement Coded (Yellow Actuator) Gull Wing for Upright Mount P Positions Actuation Packaging Screwdriver 10 Decimal K Plastic Shaft 16 Hexadecimal Keylocks F DESCRIPTION FOR TYPICAL ORDERING EXAMPLE S Stick-Tube 50 Pieces/Stick R Tape-Reel FR02F: 500 Pieces/Reel FR02K: 200 Pieces/Reel FR02KR16P-S G Shaft Actuated Hexadecimal Actuator Positions Real Coded Packaged in Stick-Tube Slides Rotaries R Gull Wing Terminals for Upright Mount ACTUATION Tactiles F K Screwdriver Plastic Shaft Adjusted by hand or with flat tipped screwdriver Adjusted with a flat tipped screwdriver Tilt Actuators are fully rotational either clockwise or counterclockwise. Actuator Colors: Orange for real coded devices; Yellow for complement coded devices. Touch TYPICAL SWITCH DIMENSIONS Upright • Screwdriver Indicators P CL (0.2) .008 Supplement BCD 78 Accessories 456 G14 (13.0) .512 (3.8) Dia .150 (10.0) .394 FR02FC10P 8 89 67 A (3.8) Dia .150 (10.0) .394 01 EF 2 3 45 23 (10.0) .394 901 Decimal (2.54) Typ .100 (0.1) Typ .004 (0.2) .008 4 2 Hexadecimal www.nkk.com (3.9) .154 (1.27) Typ .050 1 1 2 4 8 (10.5) .413 C C (0.2) Typ .008 (10.0) .394 (2.54) Typ .100 (0.5) Typ .020 (1.0) Typ .039 (1.75) Typ .069 Series FR02 Toggles 10mm Ultra-Thin SMT DIP Rotaries TYPICAL SWITCH DIMENSIONS P Rockers Upright • Plastic Shaft CL 8 (13.0) .512 (3.8) .150 (10.0) .394 Decimal 2 1 1 2 4 8 (10.5) .413 C C (0.2) Typ .008 (3.8) Dia .150 (10.0) .394 4 Pushbuttons D BC E 78 456 (3.8) Dia .150 F 012 789A 23 (10.0) .394 3456 901 (0.5) Typ .020 (7.0) (3.9) .276 .154 (1.0) Typ .039 (1.75) Typ .069 Hexadecimal FR02KC16P PACKAGING Stick-Tube Keylocks S FR02F & FR02K Each stick-tube contains 50 switches. Switches must be ordered in 50-piece increments. G (16.2) .638 (540.0) 21.260 FR02K Switches must be ordered in 200-piece increments. This packaging meets EIA-481-2 Standard. Each tape-reel of 550 pockets contains 500 switches. Minimum Leader Length: 15.748” (400mm) Minimum Trailer Length: 6.299” (160mm) Each tape-reel of 250 pockets contains 200 switches. Minimum Leader Length: 15.748” (400mm) Minimum Trailer Length: 6.299” (160mm) (80.0) Dia 3.150 901 (80.0) Dia 3.150 78 (2.0) Typ .079 (4.0) Typ .157 (16.0) Typ .630 (1.2) Typ .047 901 78 456 Direction of Feed www.nkk.com (12.2) .480 (1.5) Dia Typ .059 23 (1.5) .059 (10.3) Typ .406 (2.1) Typ .083 3 Max (11.5) .453 (24.0) .945 (24.0) .945 (0.4) .016 Direction of Feed (1.75) .069 FR02K (10.0) .394 456 (24.4) .961 (4.1) .161 (4.6) .181 (1.5) Dia Typ .059 3ϒMax (11.5) .453 (30.4) Max 1.197 (10.5) Typ .413 (2.0) Typ .079 (10.3) Typ .406 Touch (1.2) Typ .047 (24.0) .945 (6.5) R .256 Overall Dia (330.0) 13.0 (16.0) Typ .630 23 FR02F (2.0) Typ .079 (4.0) Typ .157 Accessories (1.75) .069 Tilt FR02F Switches must be ordered in 500-piece increments. This packaging meets EIA-481-2 Standard. Tactiles Tape-Reel Supplement R Slides (16.6) .654 Indicators (10.0) .394 (1.27) Typ .050 Programmable Illuminated PB (0.2) .008 (2.54) Typ .100 Rotaries (0.2) .008 (2.54) Typ .100 (0.1) Typ .004 (0.5) .020 G15